Search Documents

By M. Buxton

Sensor derived data can add value across the mining operating chain ranging from resource definition, extraction, pre ? concentration, mineral process monitoring and assessment of product quality. Most documented studies on the use of sensors in mining focus on specific technologies for specific applications. These studies do not take into account different aims, objectives and operating conditions at different steps in the value chain. The first part of this contribution assesses key physical performance and discriminatory requirements of sensors applied in each portion of the mining value chain. The second part proposes a framework of methods for quantifying the value added by additional sensor information. Integrating the sensor based technology and the economic value quantification allows for both, designing an economically optimal sensor monitoring network along the whole mining value chain and optimizing efficiencies. Illustrative studies demonstrate the significant economic benefits, in particular in reduction of exploration expenditures, increase in extraction efficiencies, increase in ore product quality and improvement of processing efficiencies.

Feb 27, 2013

By Burton Scott

A device for detecting carbon monoxide at ppm levels is described which is based on the measurement of infrared absorption at 4.65 microns. The unique feature of the nondispersive infrared instrument is contained in the optical design which includes a confocal cavity, increasing the effective optical path length by a large factor, thus greatly reducing the required package size. The cavity has the effect of reducing the total amount of radiation passing to the detector, but at the same time increasing the percent attenuation observed when adding CO, by a factor called gain. The radiation is chopped by a filter wheel which contains narrow band filters at 4.0 and 4.65 microns. The resultant signal produced by the pyroelectric detector is demodulated by the electronics to product an automatic gain control signal, proportional to the total radiation, and a difference signal, proportional to the CO present. Tests of a breadboard model are described which show cavity gains of 10 with noise levels equivalent to 2 to 10 ppm CO.

Jan 1, 1975

By S. Stefanizzi

In the present paper, numerical simulations based on a finite/discrete element approach are used to study deformation and failure process during standard rock mechanics. FEM/DEM modeling has been used as available with the ELFEN code, which explicitly model the transition from continuum to discontinuum. The transition is simulated through a crack nucleation and propagation that obeys to the Griffith?s failure criterion. If the fracture criterion within the intact rock (represented by FEM) is met, a new crack (represented by DEM) is initiated. Remeshing allows the fracture process through the FEM mesh to be tracked and visualized, thus contact properties can be assigned to pre-existing fractures and newly generated fractures. In this study, compressive tests of rock samples are simulated. The applicability of ELFEN to properly and efficiently simulate typical laboratory rock mechanics tests, with reference to the rock fracture process, is described in detail. In addition, an indirect validation of the extensional strain criterion proposed by Stacey (1981) is given.

May 1, 2009

By Richard F. Hewlett

The purpose of this Bureau of Mines paper is to provide the mineral industry with current information on high-speed data processing and to illustrate how some of these techniques can be applied to the industry. The need for applying these techniques is generally recognized, but not much information is readily available on specific applications. This paper briefly describes high-speed data processing and reduction equipment in an effort to familiarize the reader with the functions of the equipment. A list and explanation of some of the possible applications of high-speed data processing for the mineral industry are included. A few of these applications are illustrated by the use of specific examples of existing computer programs or processing methods, including their calculation times and costs. Some of the programs cited herein were developed by the author at the University of Arizona for a Masters thesis in mining engineering. When a reference is made to a specific computer, the reference is given to make the information that is being presented as factual as possible; most of the manufacturer's equipment that is mentioned in the references was available at the University of Arizona, and no specific endorsement of that manufacturer is intended.

Jan 1, 1962

By R. L. Pascual, W. J. Whiten

"The froth flotation process is not well understood. Both flotation models, and the parameters used to describe the stream flows are not well defined. They in fact vary considerably in different applications. This creates difficulties is designing a simulation program suitable for use by plant personnel, consultants, and researchers. In addition to simulation, an effective simulation program can be expected to provide a range of other services.This paper shows how a process circuit simulator can be designed with sufficient flexibility to satisfy these needs, and discusses some of the additional services.OVERVIEWThe development of a simulation program for froth flotation circuits faces several challenges as flotation models and the associated stream descriptions are not well defined. There is little agreement on the best form for a flotation model, or on how the plant streams should be defined.In addition to simulation, a flotation simulator is generally expected to provide other services such as data input, data reconciliation, model fitting, and accuracy estimation. Additional services may also be needed beyond what might initially be envisaged. A summary of some of these possibilities is included.To apply simulation to a flotation circuit it is necessary to develop a flotation cell model, for instance based on the general outline given in the appendices. Experimental data, usually from the plant, is needed to determine cell model parameters. This is generally done by first undertaking data reconciliation to determine if mass flow constraints are sufficiently closely satisfied. At the same time the data is inspected for outliers that might bias subsequent calculations. Next the data is fitted to a model to back calculate ore characteristics. If there is sufficient agreement between the fitted model and the data, the model can then used to make predictions of the effect of changes to the plant. The changes, that the simulation shows are beneficial, can be applied to improve plant performance"

Jan 1, 2003

By Unknown

We are indebted to the Consolidated Mining and Smelting Company of Canada Limited for the several pictures in this issue showing the progress made in new construction at Tadanac and at Bonnington Falls, B.C. Plate No. 1 shows the down-stream side of the No. 1 hydro-electric station of the West Kootenay Power and Light Co. Limited at Bonnington Falls, on the Kootenay river, at which 17,500 k.v.a. will be developed to meet the requirements of the enlarged zinc and lead refineries at Tadanac. The generators, exciters and switch apparatus were supplied by the Canadian General Electric Company and the step-up transformers by the Canadian Westinghouse Company Limited. The plant throughout was designed, manufactured and erected by Canadians. Plate No. 2 shows the casting room of the new lead-plant and plate No. 3 the new tank-room of the electrolytic lead refinery at Tadanac. These additions will increase the capacity of the lead refinery by some 150 tons daily. The extensions also include practically doubling the zinc plant, and the gold and silver refineries. With the exception of the new stack, all designing construction and installation of the various plants is being done by the Company's own employees at Tadanac. Plate No. 4 shows the progress made in the construction of the new reinforced concrete stack at Tadanac. This stack, of 21 feet inside diameter at the top, will be brick lined and when completed will rise 400 feet above its foundations: the tallest of its kind in the world. The construction is in charge of the Rust Engineering Company of Pittsburgh, Pa. Plate No. 5 is a panorama of the Tadanac smelters and refineries. The photograph was taken from the roof of the lead smelter and gives an excellent idea of the size of the plant and its surroundings. Tadanac produces electrolytic lead, zinc and copper and fine gold and silver. During 1924 the company treated 1,333,523 tons of ore and produced: 161,400,- 769 pounds of lead; 92,197,824 pounds of zinc; l,382,750pounds of copper; 4,074,044 ounces of silver, and 26,976 ounces of gold.

Jan 1, 1925

By Lianyang Zhang

For optimal design of rock socketed shafts used to support axial loading, it is important to predict the end bearing capacity. The existing empirical methods for determining the end bearing capacity of rock socketed shafts use the empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of intact rock, sc. Since rock socketed shafts are supported by the rock mass (both intact rock blocks and discontinuities separating them) not just the intact rock, one should consider not only the intact rock properties but also the influence of discontinuities when determining the end bearing capacity. Although the effect of discontinuities may have been implicitly (partially) included in the empirical relations derived from the results of load tests, it is not clear how big the effect is and how much of it has been included. In this paper, a database consisting of 50 test shafts, 25 of which contain the RQD (rock quality designation) value, is developed. Using the database, the applicability of the existing empirical relations is evaluated and two new empirical relations between the end bearing capacity, qmax, and the unconfined compressive strength of rock mass, scm, are derived. The new empirical relations explicitly consider the effect of discontinuities by using scm which is directly related to RQD. Finally, an example is presented to demonstrate the application of the newly derived relations.

Jan 1, 2008

By F. A. Camisani-Calzolari

The latter half of the 20th century has seen the proliferation of a series of codes to address commodity needs which were brought about by rapidly advancing technologies and the globalization of markets and consumerism. This paper addresses the specific needs and the origin of this surge and presents these codes in the context in which they were developed. It also compares the main codes or groups of codes and elaborates upon their strengths and weaknesses. Three main categories of codes are identified, namely codes for reporting to international agencies, codes addressing government needs and, finally, codes for the investors and the stock market. Codes governed by international agencies usually relate to strategic commodities which have highly specialized fields of usage such as nuclear power generation where international cooperationis eventually the only viable approach for both the development of technologies and their applications. Codes for reporting to governments address the necessity of each state to exploit its mineral potential profitably and to secure the preservation of wealth for future generations. Reporting to investors is experiencing a considerable popularity as of late because of globalization in mining and the growing need for outside financing of mining projects, whose capital requirements are getting out of reach for the average mid-cap mining company. All these codes have advantages and shortcomings dictated by the specific circumstances under which they were developed, therefore necessitating the definition and implementation of some kind of international standard whereby investments and the spread of information across political boundaries would be facilitated. Though none of these codes might ever become international in the true sense of the word because of significantly different legislations at national level, a step that would greatly contribute to the cross-border disclosure of information would be the reciprocal recognition of competent persons by the major mining countries, including China and Russia. It is also becoming essential that financial institutions and investors be properly advised on mining projects by reporting reserves and resources in a transparent and responsible way with the relevant public disclosures being compiled by professionals who take full responsibility for their submissions. Keywords: reporting codes, mineral resources, mineral reserves, competent person, UN Framework Classification, IAEA classification, JORC Code, SAMREC Code and CRIRSCO.

Jan 1, 2004

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By R A. Binns, S Murao

The PACMANUS and Jade deposits are two active hydrothermal fields that are forming massive sulphide deposits at the Pacific rim margin. Both are associated with felsic submarine volcanic rocks and both occur in back-arc settings. However, PACMANUS is associated with almost sediment-free dacites and lies on the crest of a volcanic ridge, whereas Jade occurs in a heavily-sedimented tectonic depression associated with a basement of pumiceous rhyolite. The PACMANUS deposit is richer in Cu and Au, and Jade in Pb. Zinc, Ag, As and Sb contents are similar. Sulfide textures at PACMANUS suggest formation of Cu and Zn sulfides by simultaneous double-diffusion involving inwards-moving seawater mixing with outwards-moving hydrothermal fluid. By contrast, at Jade there is a more complex history of formation where initial growth of barite on the sediment surface, probably associated with microbial activity, formed an impervious cap which trapped higher temperature hydrothermal solutions.  

Jan 1, 1995

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By A T. Job, P R. McAree

There is significant value at stake in the mining industry from the implementation of new technologies that support the enhanced profitability and sustainability of mines. However, in order to realise this value, new technology must be implemented in a way that is both effective and sustainable. The industry has a mixed history for technology implementation that provides fertile ground for understanding what is necessary for innovation to deliver value. This paper describes early stage research investigating why this is so, with the aim of improving how to deliver value. Several case studies are provided covering both successful and unsuccessful technology interventions. The paper identifies the common factors that emerge from the case studies, and offers a path forward for further research in this area.CITATION:Job, A T and McAree, P R, 2017. Three case studies on the implementation of new technology in the mining industry, in Proceedings Iron Ore 2017, pp 407–414 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

The Effect of Bulk Iron Concentration on the Copper Activation of Sphalerite at pH 9

Sep 13, 2010

By J. M. Cardoso, E. F. Quadros, A. Chiarini, F. Fernandes, G. Vilela, J. Ireno, L. C. Agostini

Based on the geological-geometric characterization of the basaltic rock at the site of a factory for chemical products situated in the Southern region of Brasil, and on results of a significant number of packer tests, the principal directions of flow were estimated, taking into consideration the intersection and the orientation of the joints and the amount of contaminant flow measured in each interval. The tests were performed using the multi-packer hydraulic multitest probe of IPT (HMTP) instrumented with an electric conductivity meter. A method of analysis for three-dimensional evaluation of the amount of contaminant flow in the area was proposed for future mitigation of the problem. Basé sur une caractérization géologique-géotechnique de la roche basaltique existant sur un site dune fabrique de produits chimiques située au sud du Brésil et sur les resultants dún nombre significantif déssais du type packer, les directions principales d´écoulement ont été estimées en considerant l´intersection et orientation des joints et la quantité de contaminant mesurée sur chaque intervale d´essais. Ceux-ci ont été realizes en utilisant une sonde multipacker developée au IPT – São Paulo (HMTP) instrumentée avec un mesureur de condictivité électrique. Une méthode d´analyse 3-D pour l´évaluation du transport du contaminant sur ce site a été proposée pour une future mitigation du problème. Auf Grund der geologischen Struktur des Basalts auf dem Gelände einer chemischen Fabrik in Südbrasilien und der Ergebnisse einer ansehnlichen Zahl von Pumpversuchen wurden die Hauptfließrichtungen bestimmt unter Berücksichtigung des Kluftgefüges und der in jedem Intervall gemessenen Menge kontaminierten Wassers. Die Versuche erfolgten mit dem im IPT entwickelten Verfahren (HMTP) mit Mehrfachpackern und elektrischen Leitfähigkeitsgebern. Ein analytisches Verfahren zur dreidimensionalen Ermittlung der Mengen kontaminierten Wassers wurde für die künftige Befassung mit dem Problem entwickelt.

Jan 1, 2003

By D Craw, C Smith, C Rufaut

Oceana Gold (NZ) LtdÆs, Macraes Gold Operation currently has two tailings impoundments, the larger of which covers approximately 75 ha. When an impoundment is temporarily out of use, the surface dries and dust can be blown from the surface to the surrounding area. At present water spraying is used to stabilise the surface, but this is not ideal as Macraes mine can experience water shortages during the summer. This paper examines an alternative method of surface stabilisation using vegetation as a ground cover. The tailings have a low natural fertility, so it is important to determine what will actually grow in the tailings, and whether amendments are necessary. Also important is the effect of the amendments on arsenic mobility in the tailings as the schist rock at Macraes has naturally elevated levels of arsenic. Three plants species, rye corn, barley, and lupin, were grown in metre-deep lysimeters at Macraes mine site. The plants were grown in unaltered tailings, and tailings with one of two amendments added: Bioboost (an organic fertiliser containing biosolids), and superphosphate fertiliser. The leachate from each lysimeter was collected and analysed monthly to determine the extent of arsenic mobility. In addition, laboratory experiments were set up to determine arsenic mobility in tailings with amendments at the centimetre scale.   All plants grew best with the fertiliser amendment, with rye corn growing the best overall. Plants growing in unaltered tailings either barely survived (rye corn, barley) or died (lupin). Plants in the Bioboost amended tailings grew only slightly better than in the unamended tailings. Laboratory experiments indicate that the addition of phosphate fertiliser greatly increases arsenic leaching at the centimetre scale when compared to unamended tailings. The addition of Bioboost only marginally increases arsenic leaching, compared to unamended tailings. This trend has not been repeated in the lysimeter trials on the metre scale over four months. Current results suggest that of the plant types trialed and amendments used, rye corn with superphosphate is the most practical short-term tailings stabilisation method at Macraes.

Jan 1, 2004

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By Robert S. Schechter

This report describes the development and application of PHASEQ/FLOW, a geochemical flow simulator capable of describing the dynamic changes in chemical composition of an aqueous solution during flow in a permeable medium. The solution components can react through intraaqueous reactions, redox, precipitation, or dissolution. The assumption of local thermodynamic equilibrium ensures maximum generality with respect to the number of species and components possible; however, the fluid flow itself is limited to one-dimension. The report describes several applications: generic batch equilibria, flowing equilibria, uranium roll-front deposition, and roll-front leaching.

Jan 1, 1985

By Akul Joshi, Ming C. Leu, Robert Guttenberg, Susan L. Murray

The aerospace and automotive industries are facing a significant risk for cumulative trauma disorders from high-repetition, long-duration tasks. Additional risk factors such as shocks, vibrations and sustained uncomfortable postures oftentimes contribute to musculoskeletal, neurological injuries associated with the hand-arm system. The power tools used for the operation reduce the comfort and working efficiency of the operators, thus lowering their health and safety and the quality of operation. This paper investigates the fastening operation on the assembly line of a major aerospace company for quantifying hand-arm vibrations with the objective of developing a dynamic model of the hand-arm system. The model will be used to ascertain the effect of the various risk factors on the quality of the operation. Experiment Setup A system of three tri-axial accelerometers is used to collect vibrations entering the hand-arm system and their positioning follows the ISO-5349 standard. Reaction force during the operation is measured using a force sensor. The posture of the hand-arm system is measured using two goniometers and one torsiometer. The pilot study conducted has two subjects and one pistol-grip power tool. The experiment setup and positions of various sensors is depicted in Figure 1. [ ] Analysis Method The analysis consists of transmissibility of vibrations and frequency weighted acceleration based on the recommendations of the ISO-5349 standard [1,2]. The transmissibility [3] was deduced in frequency domain after measuring data in time domain from the

Jan 6, 2006

By G. Styles, K. Lye, R. Tenbergen, M. Mayhew

Requirements to produce a higher bulk concentrate grade have necessitated extensive use of on-stream analyser data and computer programming to obtain the targets set for Frood Stobie Mill as required by overall milling considerations.A brief history of milling process changes associated with the changes from a low grade (3% Ni) bulk concentrate in the sixties to a high (6 to 8.5%). Nil bulk concentrate currently will be presented.The heart of the presentation will be the computer control schemes for ""self optimisation"" of the distinct flotation sections in the plant within certain restraints to achieve targets set by the mill metallurgist.

Jan 1, 1985

By D. Richter

The Pyrometallurgical refining stage of ferronickel manufacturing produces a slag rich in iron and nickel, which is usually further processed for metal recovery. The recovered material is returned to the refining or smelting stages, depending on the amount of impurities. A series of tests was carried out on the Mineração Morro Azul refining slags, aiming at the recovery of the metallic particles through physical processing. Minor changes in the process showed improved results. This paper compares the textures of these slags after being cooled at ambient temperature and granulated under water at high pressure and flow. It concludes that the cooling process is intimately connected to the work index of such slags, thus resulting in direct impact in operating costs.

Jan 1, 2011