Search Documents

By R. W. Mei, R. A. Strombom, D. J. Moore

"Heat-shrinkable cable accessories are solving problems in the mining industry. This paper describes a range of products used by the industry, including low-voltage splices, high-voltage splices to 8.7 k V, cable repair sleeves, mining cable terminations used on system voltages up to 25 kV and motor connection kits up to 8 k V. Technical procedures and designs are illustrated.IntroductionThe development of high-performance heat-shrinkable materials slightly over 20 years ago proved to be one of the major technological breakthroughs in power cable accessories. Heat-shrinkable products were introduced initially for use as low-volt age cable accessories in the aircraft and electronics industry. A program of continuous development and product introduction now enables the manufacturer to offer a broad range of products for mining, industrial and utility electrical systems.With the advent of atomic energy, an important discovery was made-exposure of some plastic materials to high-energy electrons can cause the permanent crosslinking, or intermolecular joining, of adjacent molecules. Once the material has been crosslinked, it will not melt or flow at any temperature.The unique properties of heat-shrinkable products also result from the exposure of special thermoplastic formulations to high-energy electrons. Because of crosslinking, these products have perfect elastic memory. The heat-shrinkable products are supplied in expanded condition. When heated, they will shrink and tightly cover the object over which they have been placed. 'The functional and operating demands of mine cable accessories exceeded the classic electronic applications of heat shrinkable materials. These demands required a very sophisticated program to develop materials and adhesive systems that could endure the operational environment associated with the mining industry,Ease of assembly, low installed cost and operational reliability are among the main reasons for the acceptance of heat-shrinkable mine cable accessories in electrically powered mines. For over a decade, these systems have been demonstrating proven performance."

Jan 1, 1980

By P. K. Narasimharaghavan

The major threat to the sustainability of Aluminium Industry is its significant contribution to global warming by way of generation of non eco-friendly gases during its production cycle from Bauxite to the finished product. Though reduction measures are taken in control and effective recovery of values from pot room gases, efforts in use of environment friendly additives in the final products production line is warranted. In this line, the present paper describes our efforts in the use of a new generation refining flux which apart from helping in effective removal of alkali metals, reduction in inclusions and ensure a better metal cleanliness shall also aide in reduction of obnoxious gases generated during the metal refining process prior to casting. The aim of the current work was to reconcile the practical results with the old generation fluxes used. Further improvements to bring in a better metal cleanliness will also be discussed.

Jan 1, 2010

Most analysts determining tungsten trioxide in low grade samples are aware that colorimetric procedures do not possess the inherent disadvantages of gravimetric methods operating on milligram quantities of tungsten trioxide. Apart from the inaccuracies associated with weighing four or five milligrams of ignited oxide in a platinum crucible of about 30 gm. weight with a large surface area to absorb moisture, using a 5 gm. charge on samples less than about 0·15 per cent tungsten trioxide, it is extremely difficult toget complete or pure precipitation of tungsten with cinchonine, cinchonine plus alpha benzoin oxime, rhodamine B or any other of the commonly used precipitants. Table 2', No. 8, illustrates the low results obtained by gravimetric as opposed to colorimetric procedures. In addition the colorimetric determination requires only a small portion of the time consumed by gravimetric practices and the increased accuracy obtainable in low ranges together with the saving in time made it highly desirable to develop a colorimetric method suitable for King Island ores.The most commonly used colorimetric method is that introduced by Feigl and Krumholz (1932), since modified by various investigators (Grimaldi and North, 1943; Sandell, 1946; Westwood and Mayer, 1947; Gentry and Sherrington, 1948; Freund, Wright and Brookshier, 1951; Grouthamel and Johnson, 1954; and others). Stannous chloride is used to reduce tungsten followed by colour development with a thiocyanate, usually sodium, potassium or ammonium.Other reducing agents have been proposed (Emery and Curtis, 1948), but only in recent years have the conditions governing maximum colour development been fully estab...

Jan 1, 1958

By A Rojc, J Ronaszeki, C Smith

Nuclear logging was tested for the in situ determination of Fe, Si, and Al in iron ore blastholes with field tests at the BHP Billiton Iron Ore, Mount Waleback Mine. Prompt gamma neutron activation analysis (PGNAA) was used to determine percentages of Fe and Si while natural gamma logging was employed for the determination of Al. The accuracy given by nuclear logging is comparable to the accuracy provided by the laboratory analysis which was determined by taking the average of four samples collected from the cuttings deposited on the surface around the perimeter of a drill hole. The work also indicated that there is a chance of determining Al by PGNAA.

Jan 1, 2002

By R. K. Jade

Although several studies in combining and bifurcating flows in two-way junctions and splits are reported, deviations persist in the estimated shock loss coefficients (SLCs). Due to their complex nature, more work has to be done to be able to correctly predict flow losses at these locations. In two-way splits, the flow at bifurcation is known to be characterized mainly by two recirculating zones in the downstream branches, whereas, in a junction one recirculating zone is observed immediately downstream of the main branch. The relative flow rate in the branches (quantity ratios) is treated as the only parameter defining the losses at these locations. However, the effect of wall roughness, if any, on SLCs becomes important for mine ventilation. This paper presents the critical determinants of shock losses at splits and junctions at varying quantity ratios. The flow at 90º split and junction was examined both experimentally and numerically for Reynolds number in the range of 1.0×104 to 1.6×105. With a well designed laboratory setup, using precision instruments, velocity and pressure measurements were carried out, by using two scales of wall roughness. 3D numerical simulations for these experiments were conducted by using ANSYS CFX modeling tool. CFD simulations yielded results that are reasonably close to experiments, providing high degree of satisfaction in numerically predicting losses across the splits and junctions. However, comparisons of these numerical simulation results with existing literature standards showed significant under-estimation of shock losses by the standard literature by as much as 50%. A clear rise in the magnitude of shock losses was noted in both the approaches, with increased wall roughness. Based on the current studies, predictor equations incorporating quantity ratios are developed for accurate estimation of shock losses. Further investigations on roughness are needed, before one is able to incorporate wall roughness into the prediction of SLC.

Jan 1, 2009

By D P. Sainsbury, B L. Sainsbury, A Vakili, H-D Paetzold, P Lourens

The cave propagation behaviour of a jointed rock mass is strongly governed by the unique nature of joints and discontinuities, together with the intact strength of rock bridges that make up the rock fabric. A discrete finite difference (DFD) modelling technique has been developed to allow for the detailed consideration of the rock mass structural fabric at many scales and through many different stress paths that can be used for complex mine-scale analysis. The DFD methodology uses interfaces to explicitly represent large-scale structures and ubiquitous joints embedded within the simulated rock mass matrix to characterise intermediate structures. Through simulated testing of DFD materials, properties such as strength anisotropy and scale effects can be obtained. This paper discusses the successful application of implementing a DFD modelling technique for the back-analysis of caving-induced subsidence behaviour of Lift 1 at the Palabora mine.CITATION:Sainsbury, D P, Sainsbury, B L, Paetzold, H-D, Lourens, P and Vakili, A, 2016. Caving-induced subsidence behaviour of Lift 1 at the Palabora block cave mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 415–426 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Anthony D. Hammond

The use of geographic information systems (GIS) as a tool to analyze and display data is gathering momentum in the mining industry. Of particular interest is the capability of GIS to link spatial features and tabular data. The application of GIS in underground mining discussed here concentrates on four technical areas. They are land ownership and mineral claims, exploration management, production and mine safety.

Jan 1, 2002

By Jinsheng Chen, S. S. Peng

The relationship between support performance parameters and parameters representative of mining and roof conditions is characterised by uncertainty, non-linearity and dependence, so the theory of artificial neural networks was selected as a basis for shield design. A computer program based on a back-propagation training algorithm was written to derive the weighting factors between inputs and outputs from field data; once these had been established two mathematical models were developed to describe the relationship. Back-calculation of field data indicates that the results generated from the neural network models are much more accurate than those derived by traditional methods and can be used with a higher level of confidence. The support density, possible yield frequency of face supports and interval of periodic roof weighting under specific mining and roof conditions can be determined by application of the models

Jun 21, 1905

By J. R. Stone, J. T. Roy

ASARC09s continuous tapper for lead blast furnace is described. Its use throughout the company's plants has resulted in higher production rates, lower labor costs, and better working conditions. It has also permitted wide latitude in blast pressures, as well as in charge and slag compositions. The practice of tapping a lead blast furnace has remained essentially unchanged for many years. In principle, it is a batch operation discharging the products from the continuous smelting of lead-bearing materials. As such, it imposes certain restrictions on the proper functioning of the smelting operation. First, it calls for a highly developed sense of timing, and a considerable amount of physical effort on the part of the operator. Dirty and hot working conditions, as well as the hazards of flying metal and slag, usually prevail. These conditions have resulted in higher labor costs, both in rate and in amount. Labor turnover has also been high. Secondly, rigid control of mechanical and metallurgical factors must be maintained. Frequent oxygen lancing of the tap hole is needed to permit tapping, thereby increasing operating costs. Rapid increases in smelting rate, plugged tap holes, or forgetfulness on the part of the operator may permit the molten material to rise above the tuyeies and freeze the furnace. Also, the operator will often blow out the tap hole after draining, filling the area with fume. Composition of charge also vitally affects the tapping. The type of lead-bearing material being smelted will naturally affect the smelting rate, and thus the frequency of tapping. The amounts and types of fluxing materials, which determine the ultimate fluidity of the slag, must be regidly controlled. Finally, the batch tapping of a continuous smelting operation of this type appears to be wrong in principle. The molten material drains into the crucible at the bottom of the furnace where it starts cooling immediately and continues to cool until tapped out. While keeping the lead molten is no particular problem, maintaining a fluid slag at all times is often difficult, and sometimes impossible. These factors all point to the desirability of a method for the continuous tapping of a lead blast furnace. The expected advantages would be more desirable working conditions, lower labor costs, increased production, and a much wider latitude in both blast pressure and charge composition. CONTINUOUS TAPPING Historical. A number of devices, e.g., mechanical tappers, siphons, and lead wells, have been tried in the past in attempting to effect continuous tapping. None proved to be entirely satisfactory for tapping lead and slag simultaneously. It was not until 1955, however, that ASARCO designed and put into operation a successful tapping unit at its East Helena, Mont. lead smelter. This unit is described in detail in U.S. Patent NO. 2,890,951. Continuous Tapping Unit—See Figs. 1 and 2. Fig. 1 is a schematic drawing of the unit in place, showing front and side views. The component parts are identified in the caption. Fig. 2 is an actual photograph, front view, of the tapping unit attached to the base of the blast furnace. Operation. The operation of the tapping unit is quite simple. Essentially it consists of a narrow tapping bay surrounding the furnace tap hole, with a deep notch in the front wall. When the blast furnace is started this notch is open down to the level of the tap hole. Starting the furnace may be accomplished in several ways but the most satisfactory method is to plug the tap hole with clay, permitting metal and slag to build up inside the furnace. Before the liquid reaches the tuyeres, the plug is removed and the furnace is drained to the settler. The blast is then stopped momentarily while the notch in the front wall of the tapping bay is dammed with chrome brick and plastic chrome ore. The blast is again started, and the height of the dam is adjusted so that the liquid in the bay will counterbalance the internal pressure of the furnace. When the desired level is reached the slag and metal will overflow to the settler. It should be noted that the molten material ,is not siphoned from the furnace and that the metal 'acts as a liquid valve controlling the flow of slag through the tap hole. During normal operations the tapping bay is filled primarily with lead, covered with a thin layer of slag. Thus, the heavier lead plays the major role in compensating for variations in furnace pressures. Due to the high specific gravity of lead, changes in the liquid level in the tapping bay will never exceed a few inches. For this reason it is seldom necessary to change the height of the dam due to minor variations in operating conditions. Some turbulence of the liquid in the bay is essential at all times. This indicates that the level of the

Jan 1, 1963

By J. A. Theron

"This paper provides guidelines on performing mass and energy balance modelling involving coal and coal derivatives. Usually, the inputs to a pyrometallurgical process would be specified in terms of elements and compounds. Reliable thermochemical data is more widely available for species involving uniquely defined, relatively smaller molecules. However, in the case of coal, the molecules are extremely large and not uniquely defined. Consequently, modelling processes involving coal and its derivatives involve several potential pitfalls. These are outlined in the present paper.It was found that coal proximate analysis should not be regarded as absolute; it could vary with several parameters, including heating rate. For modelling, the use of ultimate analyses should be considered a preferable option to proximate analyses, where ‘fixed carbon’ and ‘volatiles’ are not defined in terms of chemical composition. Significant errors could be incurred if the larger molecules are neglected during calculation of the calorific value (CV) of coal gas (the gas liberated when coal is heated in the absence of oxygen).For elemental analysis determination, the oxygen content (which is calculated by balance) should be checked to ensure it is within the expected range. For representation of sulphur in coal, one should avoid doublecounting due to SO3 in the ash analysis.Potentially, oxygen in coal could be represented as O2, H2O, CO, or CO2.However, use of some of these species without considering the experimentally determined gross CV leads to significant errors in the energy balance. If coal enthalpy is calculated from elemental analyses without correction, representation of coal oxygen as H2O(l) gives reasonable accuracy. Coal volatiles could be represented by a complex mixture of compounds, even using different oxygen-containing species than these four, provided the enthalpy is corrected.It is recommended that an ‘enthalpy correction value’ be incorporated in energy balances involving combustion, devolatilization, or conversion of coal and coal derivatives, e.g. coke, char, or tar. That would imply that proximate analysis, elemental analysis, as well as the gross CV would be required for all solid or liquid coal-derived substances being modelled. No other correction due to carbon being present in a form other than graphite should be used, as that would imply double-counting some effects."

Jan 1, 2015

By Collin Stewart

Bowie Resources maintains one of the most pro-active ground control programs in the U.S. mining industry today. Its guiding philosophy is that everyone in the organization, from the miners at the face all the way through the top management, are involved in ground control. Some of the unique elements of the Bowie ground control program include: ? Roof bolt operators log the stratigraphy of test holes in nearly every cut. These ?lithgraphs? are used by section foremen to determine the need for additional roof support, and they are entered into the geologic data base for use in geologic modeling and mapping. ? Underground core drilling is conducted to obtain data for CMRR and stability maps. ? Weekly ?Quality? meetings, involving mine management and technical staff, are held to ensure that ground control information is integrated into production operations. The paper will describe the program in detail, discussing the involvement of roof bolters, section foremen, surveyors, technical staff, and production managers. It will also show how the program has contributed to the mine planning process. Case histories of successful ground control interventions will be discussed.

Jan 1, 2006

By James M. Harrington, A. Azra Bilgin, JoAnn Silverstein

The prevention of AMD in situ is more attractive compared to subsequent downgradient treatment alternatives that do not involve source control. AMD source control can be achieved by shifting the microbial activity in the sulfidic rock from pyrite oxidation to anaerobic heterotrophic activity. This is achieved by adding biodegradable organic carbon amendments to the sulfidic rock. This technique was applied in an abandoned mine pool with a pH of 3-3.5. Following treatment, near-neutral pH and decreased effluent heavy metal concentrations were achieved. In situ bioremediation by enhancement of bacterial iron and sulfate reduction is a promising technology for AMD prevention.

Jan 1, 2005

By Graylin R. K, dea T. R, O&apos

The Wolgan Seam of the Upper Permian IlIawarra Coal Measures of the Western Coalfield of New South Wales consists of high volatile, low sulphur, medium hard coking coal with high fluidity. This seam, 1·8-2·4m thick, in the Wolgan area, dips gently at 1°_20 ENE and lies at 160-440m below the deeply dissected surface of the western margin of the Blue Mountains plateau.A detailed study of the deposit has revealed that the Wolgan Seam consists of four main coal plies separated by three distinct stone bands. Each of these subunits is lenticular and displays individual physical, chemical and mineralogical characteristics which exhibit distinct spatial distribution patterns across the area. Most noticeable is the presence of long linear ESE-trending zones of low ash - high volatiles - high fixed carbon - high fluidity which delineate the major distributary pattern within the deltaic environment of coal formation.This seam contains some of the highest fluidity coal in the world.The Wolgan area, close to the western margin of the Sydney Basin, is characterized by:I. a regional, closely spaced, homogenous joint fracture pattern dominated by an orthogonal pair set trending 3400 and 0700, to which the face- and butt-cleat directions respectively of the Wolgan Seam are sub-parallel, and2. a more widely spaced, heterogenous, cross-cutting pattern of regional structural fractures. Zones of bad roof conditions are probably associated with these lineaments which are subvertical and trend in three majordirections, viz., 005°,035° and 115°.

Jan 1, 1980

By Don Kay

A two year study into the effects of coal mining induced subsidence on cliff lines was undertaken by the Department of Mineral Resources with the support of a grant under the National Energy Research, Development and Demonstration Program. A new monitoring technique, using an Electronic Distance Meter and acrylic reflectors attached to the cliffs, provided safety for the surveyors and extensive and accurate three dimensional displacement data on the movement of the cliffs as they were being undermined. The study report included many graphs showing the measured vertical and horizontal displacements, differential subsidence, tilts and strains and included analysis of these movements with various parameters, such as, seam thickness, depth of cover and distances between the reflectors, longwall face and the edge of the chain pillar. Some of these graphs are presented in this paper and could be used, with caution, to predict subsidence movements around other cliff lines, after allowing for differences in geology and mining layout. A mechanism is suggested as an explanation for the observed high horizontal movements around the cliff lines. Sixteen percent of the overall lengths of cliffs that were undermined during the monitoring study fell and the contributions of various factors that appeared to influence the cliff falls are discussed. It is concluded that no single factor dominated as the major cause of the cliff falls and, often, many factors combined to cause cliff face instability.

Jan 1, 1992

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By Galen G. Waddell

This report describes a method of measuring and analyzing the initial deformation which occurs in the medium surrounding a mine accessway as the opening is created. Discussed are (1) the hypothesis upon which the research is based; (2) the in situ rock-deformation measuring equipment developed; (3) the field tests, consisting of measuring the deformation of the medium around two 4-foot-diameter raise bores as the boring progressed; and (4) a finite-element technique to correlate theoretical with experimental results, using elastic theory. Described also are the raise-bore operation and performance. The instrumentation developed proved to have the sensitivity and resolution necessary to measure rock deformation around a full-scale raise bore during excavation. Tests show the relationships of rock deformation to progress of the raise boring and to time. The initial deformation of the opening appeared to be elastic. Using the deformation records and an estimated field stress, the modulus of elasticity was determined for the rock mass. In addition, the importance of this type of measurement in assessing support-problem areas is discussed.

Jan 1, 1971

By M. L. Harris

In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. The National Institute for Occupational Safety and Health (NIOSH) has developed a hand-held instrument that uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture. This instrument is called the Coal Dust Explosibility Meter (CDEM). In this study, NIOSH personnel accompanied Mine Safety and Health Administration (MSHA) inspectors on their routine band surveys in five and three underground coal mines in MSHA District 2 (PA) and District 11 (AL), respectively. While underground, NIOSH personnel and MSHA inspectors used the CDEM to assess the explosibilities of the dust samples. The values of percent incombustible content (% IC) determined by the CDEM agreed well with those obtained later by low temperature ashing (LTA) in both MSHA and NIOSH laboratories. Further, the meter identified some samples as potentially explosible that LTA analysis had found to possess sufficient rock dust for inerting. The CDEM provides more information on the hazards in the mine. Rapid identification of areas with explosible dust mixtures using the CDEM allows for immediate intervention rather than a wait of several weeks for laboratory analysis.

Jan 1, 2008

By David C. Oyler, Hakan Gurgenli, Gregory M. Molinda

Historically, miners have known that roof rocks originally composed largely of mud were prone to slaking and deterioration when exposed to water and humidity. Mine Safety and Health Administration (MSHA) records show that roof falls are more prevalent in summer and late fall. Field data shows higher bolt loads and increased room convergence in summer months. Laboratory data shows that very high internal pressures can be generated by significant strain in clay-rich rocks. In summer months humidities ranging from 70-100% can cause rock strains up to 7%, and rock pressures of 14,000 psi, more than enough to break apart weak shales and fireclays. The National Institute for Occupational Safety and Health (NIOSH) conducted wet/dry immersion cycling of clay-rich rocks. Results show that the rocks most prone to moisture deterioration are fireclays, claystones, and sandy shales, all of which have disrupted bedding. Of the 7 mudrocks with a weatherability index above 40%, none showed consistent fissile bedding. Black shales were surprisingly resistant to wet/dry water immersion cycling. Generally, mixed rocks (stackrock), typically susceptible to horizontal stress, are more resistant to moisture-deterioration. Mine roof rocks tested with moisture sensitivity ratings above 50% (moisture sensitivity index ranges from 0-100 with 100 being the most sensitive) all came from mines which had roof skin problems and used supplemental support to prevent rock fall injuries. Some roof rocks showed lateral variability of moisture sensitivity values, suggesting the need for more samples in highly varying roof rocks. Swelling strains of mudrocks showed that almost all of the swelling occurred in the first 24 hours after immersion. The wet/dry immersion cycling test used provides an accurate, quick and inexpensive method for estimating the moisture sensitivity of mudrocks. With this information mine operators can begin to anticipate hazardous ground and prepare appropriate roof support.

By Christoph Mueller

Broad band mine communication traditionally is characterized mainly by individual solutions, which have in common their long development phases and their high cost for development, operation and service. The use of Ethernet and the TCP/IP family of standardized protocols provide an uniquely price efficient combination of high bandwidth open networking, universal use and accessibility of price efficient development tools, especially because it forms the technical infrastructure for the worldwide Internet. TCP/IP and Ethernet assures reliable networking however it is not able to guarantee the latency timing of forwarding network information. Therefore, the network design requires strict load limitation and application level traffic control especially if moving equipment has to be manually remotely controlled via the network. The paper discusses the technologies the application of Ethernet and WLAN in underground mining environments.

May 1, 2006

By R. E. Kennedy

"INTRODUCTION In a previous publication4 results were given of numerous experiments made on the in-flammability of gas mixtures consisting of methane, hydro a. carbon monoxide, nitrogen, and carbon dioxide. Data were obtained and tables prepared giving the inflammable limits of each of these combustibles when mixed with various proportions of carbon dioxide and nitrogen. By the use of these data and the application of Le Chatelier's law, it was found possible to calculate the limits of inflammability of any gas mixture containing any or all of the above gases.Various mixtures of the five gases given above were prepared and their limits determined experimentally and then calculated. Good agreement was found between the determined and calculated results when complex gases encountered in mine safety work were tested. Of special significance was the accurate calculation of the limits of inflammability of gases from mine fires, gases from mine explosions, detonation products of explosives, blast—furnace gases, automobile exhaust gas, and other gases of a similar character.Using the method given in the above report, Yeaw5 investigated a number of industrial gases including oven, coal, producer, blue, carbureted blue, and dry quencher gases, and found the determined and calculated results to agree remarkably well, thus giving further proof of the value of such a means of determining dangerous conditions when combustible gases are encountered in practice.GASES FROM A POTASH MINEGases were recently encountered in a potash nine in New Mexico, containing the com-bustibles, methane, hydrogen, and ethane. In one special case a mild explosion occurred when these gases were mixed with the right proportions of air and ignited it therefore became necessary to know the inflammability of these mixtures in order that the proper precautions could be taken to prevent explosions."

May 1, 1932