Search Documents

Some of the problems associated with drill core evaluation of alluvial tin deposits and correlation with plant-scale recovery are discussed. Panning churn-drill cores on site tends to undervalue such deposits because of failure to recover completely all the available liberated cassiterite, and secondary gravity processing may also fail to give an accurate determination of potentially recoverable tin. However, by using a combination of heavy liquid separations, x-ray fluorescence analysis for Sn, and normal methods of reflected and transmitted polarized light microscopy, a quantitative assessment of alluvial material can be carried- out. The information obtained may include the liberation characteristics and distribution with size of the cassiterite, the nature and quantities of the various gangue minerals, and the amount of potentially recoverable cassiterite in the material as compared with the amount locked with light gangue minerals and hence difficult or impossible to recover. In addition, an analysis of the efficiencies of the various gravity processes, such as panning, jigging, and tabling, used to determine "recoverable tin" in the alluvial material, can be carried out. A detailed example is given of this type of investigation, in which an assessment was made of a churn-drill core from Uncia, Bolivia.

Jan 1, 1970

By Richard Weinstein, Richard Snoby

There are many advantages to upgrading coal with dry jigging technology. The most obvious is the lack of process water, which eliminates the need for fines dewatering and slurry confinement. Dry jigging eliminates the clean coal moisture penalty associated with wet processing. Particulate emissions are virtually nonexistent due to inclusions of fabric dust collectors on all modern dry jig plants. Because of the environmentally friendly nature of dry jig plants, installation permits are often measured in days, not months. There has also been a fundamental advance in dry jigging efficiency. All of these advantages have renewed the coal industry’s interest in dry jigging. But air jigging is not right for every application. There are limitations due to particle size, particle shape, moisture and near gravity content. This article explores the evolution of dry jigging. It reviews parameters important for determining the suitability of dry jigging. It also compares historical performance data as measured by imperfection, against results from modern dry jigging technology. The article also presents data from modern dry jig installations.

Jan 1, 2007

By J. K. Whyatt

This report describes a microcomputer-based instrumentation system for structural monitoring of the circular, concrete-lined Silver Shaft in northern Idaho, The 1-ft-thick concrete lining and surrounding rock mass were instrumented with a total of 12 multiple-point borehole extensometers, 16 pressure cells, 22 concrete embedment strain gauges, and 12 thermistors. The instruments were distributed among four test sites and installed immediately above the shaft bottom during sinking at the 2,414, 4,063, 5,191, and 5,955 levels. Limited access to the instruments prompted the development of a microcomputer-based remote data acquisition system that could be operated from the surface. The system scanned the instruments on a programmed schedule, printed out reduced data, and stored the data for plotting and recall. Data acquisition from off-site and uploading of data to mainframe computers were accomplished by the addition of modems to the basic system. The system is suitable for use in monitoring the structural behavior of any deep mine opening, especially in harsh operating environments and where access is limited.

Jan 1, 1986

By V. N. Cox, C. H. Grant

Both the underwater method and the rock cratering method contribute useful information in evaluating and comparing new explosive compositions. Results indicate that metallized explosive systems which contain no high explosives can be formulated to offer more energy and to do potentially more work than other slurry explosive systems. Commercial field trials are presently being conducted with a metallized explosive that does not contain any high explosive. Although there have been only a few commercial blasts to date, the results are encouraging. The Dow Chemical Co. has been engaged in explosives research since 1953. The incentive for this research was based on the desire to find additional markets and uses for magnesium metal of which DOW is a heavy producer. The thermodynamic calculations for explosives incorporating light metals indicate energies approximately twice that of nonmetallized explosives currently being used. Early in 1960, additional patent rights were acquired from independent inventors and a development station at Virginia, Minn., was set up to conduct a commercial testing and market evaluation program with this new product. The actual manufacturing of the explosive was to take place in the boreholes. Due to the complexities involved in controlling the manufacture of the explosive in the borehole, performance was sometimes in doubt. Furthermore, experience indicated that the metallized explosive systems could not be evaluated by the standard laboratory methods then being used, and it was necessary for us to look for more suitable research methods. Tests were conducted on several known methods for explosive evaluation. The most promising were the Navy underwater method for energy evaluation and a modified Livingston crater method intended to compare explosive performance in rock. After shooting over 2000 charges of 8 to 60 lb under water and in taconites and granites with many types of explosives, a metallized explosive was developed which is now being manufactured at a pilot plant in Virginia, Minn. and is being evaluated commercially. UNDERWATER METHOD An underwater method of evaluating explosives has a number of advantages. A permanent site can be established and operated indefinitely. A large number of charges may be fired in a short length of time. The medium in which the explosive is shot is exactly the same for successive shots. Data are recorded electronically minimizing human judgment. A disadvantage of the underwater method is the lack of confinement provided by the water medium. Many explosive compositions require a greater degree of confinement to develop good energy release. Although the relative significance of the two components of energy release that are usually measured, the shock energy and the bubble energy, and their relationship to breaking rock are not clearly understood, the underwater method is a valuable research tool for screening explosive compositions and gaining an insight into the manner in which explosives release their energy. Fig. 1 shows schematically the underwater apparatus. The piezoelectric gages are calibrated tourmaline crystals which convert the shock wave to an electrical impulse which is transmitted to an oscilloscope and recorded on Polaroid film. The shock traces are picked up by scopes 1 and 2. Scope 1 is timed to pick up the full trace whereas scope 2 is timed to cover the first increment of the shock trace expanded, and therefore allows full inspection of the propagation and peak pressures. Scope 3 records the bubble trace. When the explosion occurs, a bubble of gaseous detonation products is formed. The outward momentum of the water keeps expanding the bubble even after

Jan 1, 1963

By R. R. Joseph, K. A. Gschneidner

The solid solubility of magnesium in the close-packed modifications of lanthanum, cerium, praseodymium, neodymium, gadolinium, dysprosium, and lutetium was determined from approximately 250°C to the eutectoid temperature by the X-ray parametric technique. The maximum solubility at the eutectoid temperature was found to be 9.4 at. pet in La, 8.2 in Ce, 9.2 in Pr, 8.2 in Nd, 14.1 in Gd, 13.5 in Dy, and 11.5 in Lu. The solubility when compared at a homologous temperature was found to increase in a smooth manner with decreasing size factor from lanthanum to lutetium. It was found that the apparent atomic radius of magnesium when dissolved in the lanthanide solvent was constant and could be accounted for by consideration of several models dealing with departures from Vegard's law. The eutectoid temperatures for the lanthanide-rich La-Mg, Ce-Mg, and Nd-Mg systems were found to be 544", 505°, and 551°c, respectively. A study of the solid solubility of magnesium in the lanthanide metals was initiated because the valency and electron egativity difference are essentially constant and favorable for solid-solution formation, and thus one could examine the effect of size on terminal solid solutions. The size factors based on metal radii range from 14.6 pet for lanthanum to 7.5 pet for lutetium. Since the electronegativity difference is small, 0.06 unit or less, application of the Hume-~othery' and Darken and Gurry2 criteria for solid-solution formation indicates that the solubility of magnesium would be expected to be small for lanthanum (between 5 and 10 at. pet) and to increase as we proceed along the lanthanide series. A search of the literature revealed no data on the solubility of magnesium in the lanthanide metals except for the solubility of magnesium in cerium at 450oCA typical phase diagram for the lanthanide-rich end of the lanthanide-magnesium phase diagram is shown in Fig. 1. EXPERIMENTAL PROCEDURES Preparation of Alloys. The lanthanide metals used in the preparation of alloys for this investigation were prepared from the corresponding fluoride by metallothermic reduction techniques previously described by Daane.4 The chemical analyses of the metals used are listed in Table I.

Jan 1, 1965

The Bureau has published much data on sulfur (4, 15, 23)3, most of it dealing with national or international aspects of the sulfur industry. Little information, however, is available on sulfur marketing in specific States or areas, Therefore, the Bureau has conducted a survey of the resources, production, consumption, and economic future of the sulfur and sulfuric acid industry in States of the Central and Southern Rocky Mountain area - Wyoming, Colorado, Utah, Arizona, and New Mexico - and in the Northern Plains States - North Dakota, South Dakota, and Nebraska, even though these States do not represent an economic or marketing unit. The purpose of this survey is to review the demand for sulfur and primary sulfur compounds that draws upon the natural resources of the region, to discover opportunities for better use of these resources, and also to analyze and evaluate the patterns of consumption, sources of supply, and other factors that affect the demand for these mineral products. While this survey stresses the economic and marketing phases of the industry, a complementary report (32) emphasizes the resources of sulfur in Wyoming, Colorado, Utah, New Mexico, and Arizona.

Jan 1, 1962

By Frederick M. Fowkes

Dusts can be filtered out of air streams onto polymer surfaces by electrostatic trapping resulting from the spontaneous transfer of electrons upon contact between dust particles and the polymer surfaces. Such spontaneous contact electrification has been studied quantitatively in this contract with the aid of modern semiconductor charge-sensors with the aim of determining what basic principles govern the sign and magnitude of contact electrification. Information obtained by capacitance-voltage measurements of thin polymer films on silicon showed that charges as large as 4 x 1012 electrons per cm2 develop spontaneously, and that such a charge gives adhesional forces of 165 pounds per square inch (11 atmospheres). Direct measurement of dust polymer contact electrification, using silicon surface channel conductance sensors, also showed spontaneous charges of more than 1012 electrons per cm2. Some polymers can either donate or accept electrons. These included chlorinated polyethylene, chlorinated polypropylene, polyethylmethacrylate, and a copolymer of maleic anhydride with n-octadecylvinylether. Other polymers never accepted electrons but could donate electrons; these included polystyrene, pulychlorostyrune, polyvinylchloride, polyvinylacetate, a polycarbonate (Lexan), and cellulose tributyrate. Contact electrification studies were made with dusts (coal dust, a channel black, or a silica powder) contacting thin films of various polymers solvent-cast onto the semiconductor charge-sensor. Sometimes charging was instantaneous and sometimes slower, but in all but one case (coal dust on a copolymer of maleic anhydride with n-octadecylvinyl ether) the charge trunsfer was a donation of electrons by the polymer to the dust. Some

Jan 1, 1973

By J. P. Schmid

Results of a comprehensive investigation of the impact of underground mine waste disposal on the health and safety of miners are presented. Information was gathered through an extensive search of American and foreign literature and personal communication with professionals in private industry and government. All conceivable health and safety hazards directly or indirectly related to underground mine waste disposal are analyzed, catagorized, and ranked on an industry-wide basis. Positive health and safety effects are analyzed and ranked in a similar way. Both potential and known hazards and positive impacts are included. Recommendations on abatement techniques for the various hazards are presented. Case histories of a fill-related accident in a metal mine and a health hazard associated wtih coal waste backfilling are included and causes and possible abatement procedures are discussed. The rule of management in the promotion of health and safety in backfilling operation is discussed.

Jan 1, 1982

By Donald F. MacDonald

This report aims to discuss, from the viewpoint of the mining geologist, the bearing of topographic and geologic conditions on cer- tain problems that arose in the construction of the Panama Canal. T+ is published by the Bureau of Mines as a contribution to engineer- ing liters ure because it presents information that shows how geology and topography must be considered by the mining engineer in plan- ning excavations and in removing loose material and solid rock in the safest and most efficient manner. The printing of this bulletin has been approved by the governor of the Panama Canal, as it was impracticable for the Panama Canal to give this information to the general public in any of its publications. The "sword cut" of Goethals and his men did not sever the Isth- mian barrier; it merely clove the hills to a depth of 40 feet above sea level. This cut and the great areas of low valleys at both ends of it have been covered with fresh water to the 85-foot level. This high-level lake held by dams at either end, the 85-foot locks, by which ships enter it, and the dredged approaches from the two oceans constitute the Panama Canal. In the preparation of accurate estimates concerning the cost of large excavations information regarding the geologic conditions, as obtained by a study of natural features, is necessary. Drill holes and test pits will furnish supplementary geologic information, but without a gen- eral knowledge of the geologic conditions it will not be possible for the constructing engineer to answer such questions as the following: (1) What rock units will be encountered in the excavation and in what proportion? (2) What will be the cost of drilling each for blasting (3) How far apart and how deep must the drill holes be to efficiently break the rock of each to the proper size-not too fine nor yet too coarse? In this connection jointing, fissuring, bedding, toughness, and other physical characteristics must be considered (4) How steep will the slopes of the excavation stand, and to what extent will they wash and trench on exposure to the atmosphere? (5) What proportion of the material to be excavated is of such physical character that it may be utilized in any other part of the project, such as in concrete construction, road making, wharves, breakwaters, riprap work, etc.

Jan 1, 1915

By A. W. Khair

Laboratory studies indicate that the specimen size influences the compressive strength of coal significantly. In the past, the diameter/height ratio of coal and rock specimens with different geometry and its influence on failure characteristics was discussed (Khair, 1993; Khair, 1994; Khair and Xu, 1994). In the current attempt, tests are designed and carried out under uniaxial condition in the laboratory to investigate the influence of specimen size. Cubical specimens of coal with edge dimension ranging from 5 cm (2 in.) through 20 cm (8 in.) were prepared according to the standards and tested uniaxially. Results show that compressive strength of coal is dependent on specimen size until certain level and later the change in specimen size would not yield significant change in compressive strength. Cubical specimens were chosen for testing because they are not only in close resemblance to underground pillars, but they are also the most stable shape under loading. The failure characteristics of these specimens were analyzed and their applicability to pillar design aspects in coal mines is studied. A detailed analysis of the physical and mechanical properties of the tested coal seam is also presented.

Jan 1, 1996

By Donald J. Knight

HEAT Treatment at 1500' F of a mild steel containing 0.1 pct C, in an atmosphere which is oxidizing to both carbon and iron, results in the progressive oxidation of the metal surface with little or no change in the carbon content of the underlying metal. Further heat treatment of the scaled metal in either a neutral atmosphere or in a vacuum may or may not result in the decarburization of the metal depending upon the physical nature of the scale. It is apparent that if a continuous layer of oxide is present on the steel surface, the reaction OScale + Cmetal Cogas cannot progress since the SO formed gas would be unable to leave the oxide/metal interface. Thus, in order for the reaction to progress, the oxide must be cracked or porous. Vacuum heat treatment at 1500" F of samples with a thick continuous oxide scale showed no decarburization of the steel. However, when cracks were introduced mechanically into the scale prior to the vacuum heat treatment notable decarburization of the metal resulted and a structure as shown by Fig. 1 obtained, i.e., reduction of the crack walls to ferrite. With reference to the diagram of Fig. 2, it would appear that a mechanism of the following type takes place. Carbon atoms arriving at an oxide/metal/void interface, such as 'A', Fig. 2(a), can combine with oxygen atoms from the scale and leave the reaction site as Cogas thereby reducing the oxide to metal. On a greatly magnified scale, Fig. 2(b),this will appear as a ferrite projection along the crack wall. Carbon atoms entering this projection can react with oxygen atoms at point 'C', which is a new interface, and so on leading to a progressive growth of the ferrite along the crack wall and to the surface, Figs. 2 (c) and 1. It would appear that the only means by which thickening of the ferrite film can take place is by a diffusion of oxygen through the ferrite film to react with carbon at the newly formed ferrite/ void interface. Since the diffusion rate of carbon is reportedly much greater than that of oxygen, and since there is a low probability factor of oxygen and carbon atoms arriving simultaneously at the same site on the ferritehoid interface, there will be a tendency for more rapid lengthening than thickening of the ferrite layer, as is observed.

Jan 1, 1962

By Y. C. Kim

This paper describes the implementation aspect of a blast hole kriging system which has been developed for the purpose of daily ore-waste control in an open pit mine. The primary goal of blast hole kriging is to improve the ore-waste delineation procedure. A complete computer program package called Blast Hole Kriging (BHK) System was developed for IBM/PC AT or XT computer, using Fortran language and supplemented by a few Assembly language routines for bit-map manipulation. The emphasis of this paper is on the implementation aspect of the developed system. For this reason, the requirements for practical implementation and the system design considerations are discussed in the paper, as well as the main features of the University of Arizona's BHK System.

Jan 1, 1990

By Frederick H. Raab

A power-line proximity-warning (PLPW) system must have a high probability of detection (alarm activation at a specific distance), low probability of false alarm, and minimal set-up and maintenance. Tests of electric-field sensors have not demonstrated a dependable alarm distance. Alternative sensing methods such as microwave radar, optical radar, and sonar can meet the requirements by direct measurement of the range from the boom to the power line. Suitable microwave techniques include RF pulse, chirp FM/CW, and baseband pulse. Baseband-pulse radar has adequate range capability and does not require expensive microwave components. The radar cross section of a power-transmission cable is adequate for its detection optical-radar systems based upon LEDs and photodiodes are inexpensive, but can achieve only marginal performance in this application because of their limited modulation bandwidth. Since laser diodes and cryogenically cooled photosensors must be used to achieve the desired range resolution, the cost of an optical-radar system is greater than that of a microwave radar system. Sonar systems are feasible, but are not as precise and cost at least as much as baseband-pulse-radar systems. The performance of both optical-radar and sonar systems is degraded by dirt, necessitating the inclusion of a "windshield wiper.' Baseband radar appears well suited to the PLPW application. The cost of a baseband-pulse radar PLPW system is expected to be comparable to that of an electric-field PLPW system. Development and testing of an experimental model are therefore recommended.

Jan 1, 1982

By R. Sharma, S. Svoronos, S. Gupta, N. A. Abdel-Khalek

This paper presents the results of column flotation of a fine feed sample of Florida phosphate. A central composite design is used to study the main and interaction effects of parameters affecting column efficiency. The statistical design is also used to determine the optimum conditions. The results indicate that, depending on the experimental conditions, it is possible to achieve a concentrate of high grade and recovery. A concentration of 15 ppm of non-ionic frother is found to be enough to maximize the recovery at the pH of 9.5.

Jan 1, 1999

By Silvano Morelli, Giovanna Cassani, Renzo Bindi, Antonio Nicola

More than 70 km of main line and service tunnels have been excavated to date for crossing the Apennines between Bologna and Florence. A new design and construction approach, known as Analysis of the Controlled Deformation in Rock and Soils, (ADECO-RS), was adopted to tackle the extreme heterogeneity of the ground and the particular stress-strain conditions. The goal of this system is to obtain constant and predictable full section advance rates, even in very poor geology, with the highest possible level of safety and reliability. The execution of this gigantic project required the mobilization of 21 job-sites, with the concurrent operation of 30 excavation headings. The global production rates confirm the high quality of the design and the high level of industrialization reached during the construction stage, levels not previously obtained in similar conditions, using other approaches such as NATM.

Jan 1, 2003

By D Craw, G Eis

Late Cretaceous Blue Spur Conglomerate preserved as isolated remnants at Gabriels Gully, Weatherstones, Forsyth, Waitahuna Gully and Adams Flat was deposited during the intiation and early stages of extensional movement on the Tuapeka Fault zone at each locality. The deposits represent successive courses of a single fluvial system flowing across the Tuapeka Fault zone from the up-thrown (northeast) block. Each course, beginning with the channel at Gabriels Gully, was abandoned as a result of uplift-induced defeated antecedence in favour of a new course farther to the southeast around the southeast-propagating tip of the Tuapeka Fault zone. Schist and quartz in the conglomerate was derived ultimately from schistose rocks northeast of the Tuapeka Fault zone. Caples Terrane greywacke detritus in the middle and upper beds of the conglomerate was probably recycled from pre-existing sedimentary cover on the up-thrown block, following initiation of uplift on the Tuapeka Fault zone at each locality. Most of the gold is derived from vein sources in Otago Schist rocks to the north, and/or associated placers. Hydrothermal veins at Waipori, Hindon, Barewood, and Macraes are the most likely primary sources. There is no evidence to support previous interpretations of deposition by river systems flowing from the southwest, or axially along the Tuapeka Fault zone from northwest to southeast. High gold grades within Blue Spur Conglomerate should have a linear trend more or less similar to the orientation of the host channels, but are likely to drop off rapidly to the southwest. Extensions of the conglomerate-filled channels are unlikely to be preserved, but there is a strong probability that younger placers recycled from the former channels exist.

Jan 1, 1999

By P. P. Jenkins, T. G. Ball

Paper presented at the Drillex '90 conference held in London, 5 April 1990. Two drilling techniques are employed - guided longhole drilling and reverse circulation coring - for underground longhole exploration of the coal reserves and the fault structures that affect them. These are complementary to, or replacements for, surface boreholes, underground development drivages and seismic techniques. The developments of the drilling techniques and some case histories are presented in detail.

Jan 1, 1991

By Douglas C. Brunot

Mabey Inc. is providing for the shoring design for the Naples bay Center project, located in Naples, FL. The excavation is approximately 374' long by 164' wide and is 27'-8" deep at the shoring line with a groundwater level six feet below present grade. The project Excavation is for a multi-use facility for residential and retail with underground parking. The shoring design will be incorporated into the foundation walls for the building. Mabey is using its pre-engineered Super Powerbrace Plus (SPP) wales and Mega Struts to support the excavation in two phases. The system design and the design of all the pre-engineered components are by Mabey. The foundation is supported on drilled shafts arranged with the building column grid. The excavation will be completed in two phases to allow for equipment mobilization and operation on a site with limited access. The construction sequence will begin with placement of the drilled shafts. The drilled shafts will also serve as the building columns. After the drilled shafts have cured, 630 AZ24-700 x 45 ft. long sheet piles will be installed. The sheets will be arranged in two phases, divided by a center row of piles. Since de-watering in south Florida is very expensive and often downright impossible prior to placing the seal slab, all the initial foundation and excavation bracing work will be completed with groundwater in situ. The entire excavation will be excavated to 5 ft. below ground surface to allow for the installation of the wale support brackets at 12 ft. on center, welded to the sheet piles. After the support brackets are installed, the SPP hydraulic wales and the Mega Strut hydraulic braces may be installed for both phases. Once the frames and struts are in place, Phase 1 excavation is completed, followed by Phase 2 excavation. The 4-ft. thick seal slab is then placed and cured in the wet. De-watering is now possible with the seal slab in place. Once the excavation is de-watered the leveling slab is placed and cured. The center row of sheet piles is then cut off at the top of leveling slab. With the leveling slab cured, the sheet piles have enough strength to support the excavation without the frames and struts near the ground surface. The permanent sheet piles are then seal welded for water proofing and the foundation walls are cast with the sheet piles. The design is modelled in 3D using REVIT to ensure accuracy of the design. The earth pressures are developed using Coulomb theory as there is a top frame and the frame and sheet pile are flexible and move to develop an active pressure wedge. Earth pressure uniform loads and loads from predicted surcharge are modeled in STAAD to determine load effects on the SPP frames and Mega Struts. Coulomb theory and Mabey’s structural model will be tested through monitoring with Mabey’s LIVEPin system. LIVEPin will be placed in struts for each phase of construction. The LIVEPin results will be calibrated with the structural model to determine actual frames forces and will also determine the actual earth pressures applied to the system from surrounding soil. Mabey has used the LIVEPin system in similar applications and this has helped us determine modelling accuracy.

Jan 1, 2018

By K. Kohli

A case study involving a historic structure undermined by longwall mining is presented in this paper. The location of this study is in South Western-Pennsylvania; USA. The structure is 150-years old and subsided 4.5 feet. This paper discusses the mitigation measures taken to reduce the subsidence damage and its effectiveness.

Jan 1, 2002

Economic Sustainable Power for Mineral Processing

Sep 13, 2010