Search Documents

By L. D. Gent

This report reviews the current state of the art of remote control techniques for underground continuous miners. A delineation of aspects requiring additional data is presented. Also a summary and delineation are presented in overview form for the related section functions: roof control, haulage, ventilation, power supply and rock dusting. The automated remotely controlled continuous miner project is a long-range research effort. However, the program has been divided into intermediate steps resulting in incremental production increases throughout the program. Data are developed relating the impact of our proposed research and development accomplishments to potential productivity impact.

Jan 1, 1975

By Dale Matthews

The Getchell Mine, near Winnemucca, NR, was discovered in the 1930s and was initially mined to recover gold from oxide ores. During the 1940s and 1950s, gold was recovered from the highly refractory arsenic sulfide ores using horizontal kilns to roast the ores. During the 1960s, fluid bed roasters were used to oxidize the ore and recover the gold. The mine was shut down from 1968 through 1985. In 1985, heap leaching was started on the low-grade oxide ores that were available. In 1989, a pressure oxidation circuit was started to recover gold from the higher grade sulfide ores. Flowsheet The basic plant flowsheet of the Getchell Mine are shown in Figs. 1 and 2. The plant was designed to process a nominal 2.7 kt/d (3000 stpd) of ore with about an 85% onstream availability and a gold production of 15.5 kg/d (500 oz/ day). Run-of-mine (ROM) ore is fed directly to a wet semiautogenuous grinding (SAG) mill after the +457-µm (+18in.) rock is removed on a stationary grizzly. From the SAG mill, the ore goes to a ball mill where it is ground to 80% -75 µm (-200 mesh) and is then sent to a thickener. The SAG and ball mill operate in closed circuit using cyclones.

Jan 1, 1994

The methods and equipment developed and used at the Mount Isa mine to obtain samples of uncemented hydraulic fill lying above major horizontal pillars are described. From existing underground development, samples were obtained at distances up to 50 m, of which up to 30 m was through hard rock. Samples were used to predict fill behaviour as it affected mining security during recovery of the pillars.Specialized equipment for difficult sampling situations and also other sampling exercises are described.

Jan 1, 1976

By G. Bulut

The recovery of copper and cobalt from ancient copper slags from the Küre region of Turkey was investigated. A fayalitic-type of ancient copper slag containing 1.24% Cu, 0.53% Co and 53.16% Fe were subjected to an experimental study. Two different routes were followed to recover the metal values. The first route was roasting the slag with pyrite followed by leaching. The second route was flotation of the slags, roasting of the flotation tailings with pyrite and leaching. The second route was found to be suitable for the treatment of the copper slag studied. In the flotation step, a copper concentrate containing approximately 11% Cu was produced with a 77% recovery while 93% of the cobalt stayed in the tailings. In the roasting experiments, the effects of roasting time, pyrite: slag ratio and roasting temperature on the dissolution efficiencies of Cu and Co were investigated, and the optimum conditions were determined. In the tests, 87% of the cobalt dissolution was observed after one hour of roasting at 500°C with a pyrite: slag ratio of 3:1. The copper dissolution in the tests was 31%. Based on the results of this study, a process flowsheet is proposed for the evaluation of these slags.

Jan 1, 2007

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By R. Loots

High temperature creep resistant alloys are used in power plants as steam pipes and headers where they have to withstand super heated steam temperatures of up to 600ºC for the lifetime of the plant. Frequently certain portions of pipes may be subjected to excessive temperatures and consequently suffer from creep damage. Damaged portions then have to be replaced by welding new steel to the service exposed steel. Such welds will have to be subjected to a post weld heat treatment (PWHT) to relieve residual stress. During such a PWHT it is then possible for the steel to crack in the heat affected zone (HAZ) by what is known as Reheat Cracking (RHC), also known as stress relief cracking. For the present purpose the RHC susceptibility of service exposed steel was compared with that of new steel by reproducing the temperature cycle to which the HAZ will be subjected during welding in a weld simulator. This was followed by PWHT where the influence of residual stress was studied by applying a constant stress to such a weld-simulated specimen in a creep testing machine. A sharp spiral was machined along the length of the cylindrical specimen to simulate the presence of a possible weld defect. In this way it is possible to subject all portions of the simulated HAZ to the same stress intensity. For the purpose of the investigation 1/2Cr-1/2Mo-1/4V steel known to be susceptible to RHC was chosen. During testing a constant tensile stress was maintained while the temperature was increased to follow the thermal cycle prescribed for PWHT. It was found that the new steel in all instances failed by RHC along the grain boundaries in the high temperature heat affected zone. In the case of the service exposed steel the creep strength of parent metal was lower than that of new steel as a result of exposure to a steam temperature of 540°C for about 15 years. Consequently, all of the failures during testing occurred in a ductile manner by necking outside the HAZ rather than by RHC. When service exposed steel is welded to new material, it is expected that the creep strain associated with stress relaxation will mostly be concentrated in the parent steel outside the HAZ. Accordingly, it should probably not be necessary to make any extra allowance for reheat cracking during repair of steam pipes manufactured from 1/2Cr-1/2Mo-1/4V steel other than that applicable for welding new steel.

Jan 1, 2004

Three main divisions of the Proterozoic are recognized in the North-West Division of Western Australia. These are referred to, in order of decreasing age, as the Mt. Bruce Supergroup, the Bresnahan Group, and theBangemall Group. The stratigraphy and distribution of each is described, their relative ages discussed, and a brief geological history of the whole area is presented.

Jan 1, 1966

By J. E. Crawshaw

"The few previous observations of the effect of turbulence on limits of inflammability have been made on a small scale in turbulence produced either by a fan or by movement of the mixture.By a suitable amount of turbulence from a fan the lower limit of methane was 5 per cent as compared with 5 per cent observed for quiescent mixtures in the same vessel.3 With a streaming movement of the gas mixture within the range of speed from 35 to 65 centimeters per second (69 to 128 feet a minute) the lower limit was approximately 5 percent,4 For a quiescent mixture of ethane the lower limit was 3.10 per cent ethane, but with fan running at a moderate speed a 3 per cent mixture exploded.5The object of the tests herein reported was (1) to determine the lower limit of natural gas in a mixture of natural gas and air Which would be ignited and propagate violently when the turbulence was produced by explosives fired from a cannon into the mixture; (2) to observe the behavior when the mixture contained less than this low limit; and (3) to determine how turbulence produced by a fan affects thin limit.Four series of tests were run, three of which were to determine the effect of different sources of ignition: Tests with (1) an electric igniter; (2) 3F black blasting powder stemmed with 2 pounds of dry fire clay stemming used to ignite the mixture, and (3) 40 per cent straight nitroglycerin dynamite unstemmed. The fourth was made to study the effect of turbulence produced by a two-speed electric fan, using an electric igniter as the source of ignition.In both series of tests with explosives, charges of 50 and 200 were used to determine the effect of increased quantity of explosives on the lower limit of natural gas."

Jul 1, 1930

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

The history of soft and hard rock underground mining is blemished with regional instabilities of mine workings. Whilst the potential consequences of regional instability events are recognised to be high, there is a false perception that the probability of them occurring is very low. In fact, Australia has averaged more than one event per year for the past 20 years. At least five fatalities and over $100 million of losses have been associated with the events. As such, they are a core risk to underground mining and have a significant effect on the quadruple bottom line of business û safety, environment, community acceptance and economics. This paper explores the important roles that risk management has in reducing the probability and consequences of regional instabilities. It concludes that education and continuing professional development are essential elements for effectively managing the risk.

Jan 1, 2003

By Arnulf Muan, Egil Aukrust

Activities of COO in the three solid solution series COO-MgO, COO-MnO, and COO-"FeO" have been determined at 1200°C by equilibrating oxide samples with a metal phase (cobalt or a Co-Fe alloy) in atmospheres of known oxygen activities. The systems COO-MgO and COO-MnO are ideal, within limits of experimental error, whereas the system COO-"FeO" shows a slight positive deviation from ideality at the temperature of this investigation. KNOWLEDGE of activities of oxide components in solid solutions is necessary for the calculation of the cation distribution among coexisting oxide phases in many important metallurgical, ceramic, and geochemical systems. Very few activity-composition curves are available for such systems at the present time. A start on the prodigious job of obtaining such data has been made by studies of solid solutions with simple sodium chloride type structure containing NiO or "FeO" as a component.1-3 The present paper describes similar studies for solid solutions with sodium chloride type structure containing COO as a component. For the systems COO-MgO and COO-MnO, the activity solid solution is determined by the equation Here po and are the oxygen activities of the gas phase in equilibrium with the phase assemblages metallic cobalt plus oxide solid solution, and metallic cobalt plus pure COO, respectively. In the system CoO-"Fe07', the metal phase is a Co-Fe alloy rather than pure cobalt. In this case the activity of COO in the oxide solid solution is calculated from the equation where a& is the activity of cobalt in the metal phase. Because the system Co-Fe is close to ideal4 and the metal phase appearing in the present work contains less iron than cobalt even at the lowest COO concentrations of the oxide phases used may be set equal to N . Hence, Eq. [2] becomes The value of Nc, can be estimated from the relative stabilities of the oxides COO (see below) and I) EXPERIMENTAL METHOD Two different but closely related procedures were used in the present investigation to determine the activity-composition curves. In one method, the oxide solid solutions were equilibrated against

Jan 1, 1963

By Peter Cain

In response to the appearance of excessive convergence of bolted gateroads in the front abutment zone of retreating coal faces at Phalen Colliery, staff from the CANMET Cape Breton Coal Research Laboratory in Sydney, N.S. initiated a programme of roof profile measurements in the front abutment zone of longwall headgates. The results of these measurements allowed a characteristic deformation curve to be determined for each headgate, and the early identification of areas showing an unstable deformation trend. These areas were then reinforced with supplementary support. The monitoring programme was adopted and enlarged by the rock mechanics staff of the Cape Breton Development Corporation, and has been continuing for a period of approximately two years. A sufficient quantity of data now exists to be able to make an assessment of the effects of a number of mining parameters on the performance of the gateroad in the front abutment zone. The following paper describes the method of measurement, illustrated by typical results, and goes on to relate variations in rate and patterns of movement to geology, interaction, method of support and pre-mining stresses.

Jan 1, 1996

By D N. Castendyk, J L. Mauk

The world-class Waihi (>6.6 Moz Au, >41.8 Moz Ag) and adjacent Favona (>0.5 Moz Au) deposits are within a single volcanic-hosted epithermal Au-Ag district located in the southern Coromandel Peninsula, New Zealand. Gold and silver mineralised quartz veins at both deposits are hosted in porphyritic andesite flows of the Waipupu Formation. Both deposits have veins surrounded by intense widespread hydrothermal alteration that is characterised by the assemblage of quartz, pyrite, adularia, illite or interstratified illite-smectite, plus less common chlorite and albite, which is locally overprinted by minor calcite or rare kaolinite. Quantitative mass transfer calculations using Gresen's general metasomatic equation indicate that hydrothermally altered andesite at both deposits is enriched in silicon, potassium, rubidium, barium, sulphur, gold, arsenic and antimony, whereas sodium, strontium and calcium are mostly lost. Iron and magnesium show mixed gain and loss. Element gain or loss can be directly related to the prevailing alteration mineralogy. Addition of potassium, rubidium and barium coupled with the concomitant loss of sodium, strontium and calcium in intensely altered wall rocks corresponds to the replacement of plagioclase by adularia or illite. Partial retention of sodium and calcium reflects the presence of hydrothermal albite and calcite, respectively. Mass balance calculations show distinct element gain and loss that can be related to the intensity and type of alteration mineralogy. However, because most rocks are intensely altered and the progression into less altered peripheral rocks is not observed in this study, the lateral extent of elements gain or loss is unconstrained with anomalies extending at least 200 to 300 m away from major veins.

Jan 1, 2003

By Frank P. Frandina, Michael J. Loehr, Paul E. Gabryszak

The Heartland Corridor Clearance Improvement Project is part of a regional Public-Private initiative to allow double stack container trains a direct route from the Port of Norfolk through Virginia, West Virginia, Eastern Kentucky and into Central Ohio. In the Preliminary Engineering stage, 30 existing tunnels were assessed and 28 were found to need clearance improvements to allow the use of double stack trains. Alternative tunnel enlargement methods were developed to achieve the desired clearance improvements, while maintaining structural integrity and minimizing disruption to train traffic. This paper summarizes the geometric and condition investigations of the existing tunnels, as well as describes the preferred methodologies to achieve the desired clearance. The clearance improvements will be implemented beginning in the summer of 2007.

Jan 1, 2007

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By R Tom Watts

The blasting industry has changed more in the last five years than in any period to date. The equipment utilized to load boreholes has changed in response to more precise blasting products and programs, and the need to maintain tighter control over product formulations produced by bulk loading equipment. Tread Corporation has built over 1,300 heavy ANFO type bulk loading units currently operating in over 40 countries worldwide. These units have been designed to meet almost every possible loading scenario but there are always new situations that require special designs and configurations to meet the challenge. The focus of this presentation is to make you aware of the process that should be used to determine the equipment best suited for your application. We will discuss loading cycle times, delivery rates, multiple product mixing capability, capacities, manpower utilization, regulatory compliance, and where and when to use automation in the loading process. We will also discuss the suitability of chassis with regard to ground pressure, turning radius, terrain, weather conditions as well as highway suitability. The US Bridge Law as well as laws that cover the concept of axle loading and spacing will be covered. Through new computer aided design and modular design capabilities, you can now have almost any configuration required to meet your bulk loading objectives. We will also review the range of equipment currently available in the market place and discuss tradeoffs between price, capacity, and complexity.

Jan 1, 2000

By I Clark, S C. Dominy

Bulk sampling programs are typically applied in coarse gold mineralised systems to verify resource/reserve grades. In recent years, there have been controversies surrounding some results of underground bulk sampling exercises compared to the predictions using diamond drill data. Just how realistic is it to predict 100 t lots from drilling that was designed to model blocks of several thousand tonnes? This study looks at the variation of relatively small units within larger planned mining units and compares some of the geostatistical techniques which purport to provide tools for such studies. Relative difficulty of application, computer timings and summaries of results will be used to illustrate the likely variation in bulk sampling units as opposed to mining units and large-scale planning units. A case study based on publicly available data from a gold project in North America is presented. A simplistic and unconditional geostatistical simulation model demonstrated that up to 50 per cent of a relatively high-grade mining block could show as uneconomic low-grade subblocks. A subsequent study will consider a similar demonstration using uniform conditioning. Erroneous impressions of early sampling results can lead to unsupported prejudgements of the final results. Bulk sampling programs require detailed planning based on ore characteristics, where protocols must fit the mineralisation type. Any program requires definition of aims and data quality objectives across grade, geological, geotechnical and geometallurgical parameters.CITATION:Clark, I and Dominy, S C, 2017. Underground bulk sampling, uniform conditioning and conditional simulation – unrealistic expectations?, in Proceedings Eighth World Conference on Sampling and Blending , pp 3–20 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By Junji Shibata

It is important to recover and reuse the metal values contained in various industrial wastes in a viewpoint of environmental preservation. Most of industrial products are made through the processes to separate impurities in raw materials, solid and liquid wastes being necessarily discharged as industrial wastes. Chemical methods such as solvent extraction, ion exchange and membrane, and physical methods such as heavy media separation, magnetic separation and electrostatic separation are considered as the methods for separation and recovery of the metal values from the wastes. In this paper, some examples of the application of solvent extraction to the treatment of wastes are introduced. The treatment of solid wastes such as Ni-Co alloy scrap, Sm-Co alloy scrap, fly ash and flue dust, and liquid wastes such as plating solution, the rinse water, etching solution and pickling solution are accomplished using solvent extraction technique.

Jan 1, 1996

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940

By A. R. T. Denues

The Explosives Division of the Bureau of Mines, United States Department of the Interior, is investigating cushioned blasting at the Explosives Testing Station, Bruceton, Pa. The general interests of this investigation are practical and relate particularly to safety. The immediate concern is an application of cushioned blasting in coal mining. In cushioned blasting, various means are employed to reduce the intensity of the application of energy in an explosive action in a borehole. The primary object is to increase the efficiency of the use of explosives.

Jan 1, 1940