Search Documents

By Robert J. Maron, Mark Fernald, Alex Van der Spek, O’Keefe. Christian, Tim Bailey

"Sonar array-based non-invasive flow measurement technology is becoming an accepted and many times a preferred method of measuring challenging single and multi-phase flows in the mineral processing industry. This fundamental sensor and measurement technology has been extended to two developments that provide new measurement capabilities useful for monitoring and managing slurry flows and pipes.The first development is the non-invasive measurement of real-time velocity profile of slurry flow in horizontal pipes. Multiple non-invasive passive sensors measure localized velocities and are combined to provide a velocity profile measurement. This information can be used to determine the approach and onset of solid deposition on the bottom of the pipe. Having this information in real time can enable operation at lower velocities and/or higher solids concentration while avoiding solids deposition or plugging and its associated operational costs.The second development is the non-invasive measurement of pipe wear on slurry lines. Presently, such measurements are made by hand-held portable ultrasonic thickness gages. The numerous shortfalls associated with the manual method are overcome with a set of permanently or semi-permanently installed transducers clamped onto the outside of the pipe. This ring of sensors contains a series of conformable ultrasonic transducers spaced around the circumference, which are used to measure the thickness of the pipe under their respective locations. Compared to manual methods, this system and approach results in better repeatability and accuracy. It also decreases inspection labor costs and pipe access requirements. The minimal accuracy variations in the presence of varying environmental temperatures will be shown. Trending of pipe wall thicknesses in high wear pipelines will be illustrated. The benefits of significantly improved pipe wear monitoring in hydrotransport lines with abrasive solids, and associated improvement in the ability to insure safe operation and avoidance of costly environmental damage due to leaks caused by pipe wear will be discussed."

Jan 1, 2009

By Dermot Winters

The Surface Mining Control and Reclamation Act (SMCRA, or the Act) was enacted on August 3, 1977. The Act was written, in part, to put an end to uneven environmental standards and to establish minimum national standards. Certainly, one of the motivating factors for passage of the Act was the success of the Federal Coal Mining Health and Safety Act of 1969 in reducing deaths and injuries in the coal industry nationwide. Section 516 (b) (1) of the Act requires *that subsidence be prevented from causing material damage to the extent technologically and economically feasible except in those instances where the mining technology requires planned subsidence in a predictable and controlled manner. Section 516 (c) of the Act authorizes the regulatory authority to suspend underground mining if there is imminent danger to inhabitants of urbanized areas, cities, towns, and communities. On December 13, 1977, the interim program, which applies a portion of the performance standards of the Act, was promulgated. Then on September 18, 1978, the proposed permanent program was published for public comment. Finally, on March 13, 1979, the final permanent program was promulgated and the States were given a period of time to submit their programs for approval.

Jan 1, 1986

By Patrick Pelletier Jr., Pierre-Alexandre Bossé, Gianni Bartolacci, Ian Orford, Steve Parent

"Over the last decades, many authors have shown the importance of froth in the flotation process. Mineral recovery is related to froth recovery and flotation. Selectivity is affected by froth characteristics, especially structure and loading. The characteristics of froth textures could therefore be used for diagnosing flotation.Machine imaging, especially image texture analysis, allows on-line measurement of important froth characteristics and process state classification. The measured characteristics include froth texture, loading and stability indicators. To extract information from images, texture analysis tools are used as well as a block-matching algorithm (BMA). For process state classification, images are analyzed with the same tools and clustering is done with multivariate data analysis algorithms.Two case studies, Brunswick Mine Concentrator Cu/Pb circuit and LaRonde Mine Zn circuit, are presented to show that these indicators may be used for diagnosis and control. The influence of manipulated variables on measured froth features is shown as well as the relationship between froth characteristics, mineral recovery and flotation selectivity.INTRODUCTIONImaging is a way to depict abstract characteristics of a scene or an object; it is often related to other types of scientific observations, chemical component concentrations, for example (Geladi and Grahn, 1996). In this paper, the scene is flotation froth. Imaging can be especially useful in applications where it is difficult to obtain the measurements needed for process analysis – froth flotation, for example."

Jan 1, 2006

By R. Le Houillier, M. Nagamori, A. J. Plumpton

"Asbestos tailings are a typical serpentine, hydrated magnesium silicate, consisting primarily of antigorite and a few per cent of unrecovered fibrous chrysotile. Serpentine has unique thermal properties in that dehydroxylating calcination at 600 to 700°C can yield an amorphous structure in which most of the magnesia is liberated from the original bond with silica and thereby rendered chemically active. The amount of activated magnesia can be quantified by selective leaching with a weak acid such as acetic acid. Many wet processes have been proposed to extract magnesium values from calcined or natural serpentine by means of various acids and their ammonium salts. However, the only commercial utilization of serpentine today is found in dry processes such as the production of fused magnesium phosphate fertilizer .The present paper reviews the physical chemistry of the dehydroxylation of serpentine and also various wet and dry processes in order to provide a general view regarding the chemical transformation of asbestos tailings.IntroductionAsbestos fibers occur as chrysotile, a serpentine polymorph. More than nine tenths of mined asbestos ores consist of massive non-fibrous serpentine, primarily the polymorph antigorite, which is discarded as tailings after fiber extraction. For many decades, Quebec has been a world leader in the production of asbestos fibers. As a result, colossal tonnages of serpentine have accumulated in the Eastern Townships'!'. Serpentine minerals are found in large deposit s throughout the world, and significant research efforts have been made, particularly in Japan and the USSR, mostly in attempts to extract magnesia or silica values therefrom.The chemical composition of serpentine (chrysotile and antigorite) may be ideally expressed as Mg3Si2Os(OH). which corresponds to 43.7% MgO and 43.3% SiO2. Natural serpentines often contain a few per cent of Ni-bearing magnetite and other impurities, and therefore the contents of MgO and Si02are both about 40% or lower.Serpentine (hydrated magnesium silicate) is virtually insoluble in weak acids. However, when dehydroxylated under controlled conditions, ' it decomposes to an amorphous state in which magnesia and silica are isolated and chemically active. The magnesia so activated is readily soluble in weak acids. This unique characteristic of calcined serpentine, first discovered in 1942,, has since attracted the attention of innumerable researchers, whence many processes have been proposed."

Jan 1, 1980

By Wolfgang Gütter

India is targeting to boost its electrical capacity from 100 GW to 200 GW within the next 10 years. The National Hydroelectric Power Corporation (NHPC) has decided in2001 to take execution of the 800 MW Stage-II of the prestigious 2,051 MW Parbatihydrol electric project in Kulu district of the northern province Himachal Pradesh. Two parallel 30° inclined underground pressure shafts of 1.542m in length each will be excavated in different geological formations and lined with hexagonal concrete segments by a hard rock double shield TBM. That kind of heading will be a novelty to India and an innovative method for inclined pressure shafts. The 4.88m Mitsubishi DSTBM will be assembled underground on a swivelling steel platform especially designed for the launching as well as for the acceptance of the TBM in the upper cavern of each shaft. The hexagonal segmental lining system causes a significant higher job safety than an open TBM with conventional support. Each ring consists of four honeycomb segments with 20 cm thickness. After finalisation of the excavation a steel liner will be installed and concreted. The Joint Venture Jäger-Seli will perform the two pressure shafts as a sub-contractor for the Indian company Gammon India Ltd.

Jan 1, 2005

By Theo. A. M. Salet

The historic centre of one of the most beautiful cities in Northern Europe -Amsterdam - is being excavated to accommodate the new North/South metro line. This new line is due for completion in 2012, and will link the Buikslotermeerplein district north of the harbour, underneath the Central Station and the old city with its gables and picturesque canals, to the commercial centre in Amsterdam Zuid/WTC. Three underground stations are being construction in the old city at Rokin, Vijzelgracht and Ceintuurbaan. The logistics of working in the middle of an historic city are demanding -maintaining tram, vehicular traffic and pedestrian access along narrow streets, providing suitable protection for the public alongside the working areas, arranging adequate delivery routes, as well as monitoring the old and mostly historical buildings for potential settlement. Safety of both the public and adjacent properties is paramount. Diaphragm walling - 1.2m & 1.5m thick and up to 48m deep - was chosen as the support system for the three deep metro stations. Challenging engineering as well as state-of-the-art equipment to construct the diaphragm walls was needed in order to meet the tight working specifications, in the narrowest locations imaginable. Extreme conditions call for innovative solutions.

Jan 1, 2006

By M. R. Geer, H. F. Yancey

"INTRODUCTION With the advent of war in 1941, military operations in Alaska were enlarged on such a scale that the demand for coal in the Territory more than doubled. Coal was needed urgently for heating forts and other military establishments, for use on large construction projects, and for handling the greatly increased volume of traffic on the Alaska Railroad. -The additional tonnage required, estimated at perhaps 250,000 tons per year, probably could have been supplied by the United States, but shipping space between Pacific Coast ports and Alaska was already overburdened with military supplies and construction materials. Moreover, although of only secondary importance in wartime, the cost of coal shipped into the Territory is reported to have been as high as $40 per ton. The alternative to importing coal was, of course, to increase the Production of the Alaska mines.Production of coal in Alaska reached, 350,000 tons in 1944, or more than double the prewar' output. The responsibility for increasing coal production was assumed largely by the Army, A Coal Commission attached to the Alaska Department arranged financial assistance for some mining operations, aided the operators in producing equipment for mechanization, and provided most of the labor necessary to operate the mines. The Bureau of Mines contributed to the program in several ways. First, exploration by the Bureau in the Moose Creek district revealed a substantial tonnage of coal of better grade than any currently mined in the Territory, 4/ and drilling in the Broad Pass district, where a mine to supply coal for the army had been started, revealed that the reserves were far less than had been supposed; this operation was abandoned. Second, coal-preparation practices were studied, and recommendations for improvements made, at two of the operating mines at which the quality of the coal makes preparation a factor of vital importance. Some of the information obtained in these studies forms the basis for the present report."

Jan 1, 1946

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

Provide the U.S. mining industry with technology for designing environmentally sound, low-cost in situ leach mining operations to produce copper from small, deep, and/or low-grade copper oxide deposits. Approach Investigate the feasibility of a new mining method--in situ leach mining-as an alternative to conventional mining for copper. Study fundamental leaching technology that will facilitate future commercial operations. Develop guidelines and procedures that will enable mine operators to design and evaluate in situ leach mining operations for any specific copper oxide deposit.

Jan 1, 1989

By N. I. Aziz

The importance of using disc cutters for rock excavation is reflected by their wide application in hard rock cutting machines such as tunnel boring machines and raise borers. The forces involved in the cutting process are those due mainly to thrust and rolling forces and are greater than that required by cutting picks. An interesting feature of cutting with discs is the formation of surface crushing, surface and sub-surface chipping and primary crack formation. Experimental, as well as analytical, work has been carried out to determine the optimum spacing between the disc cutters to control primary crack orientation. Wedge bit indenters were used to simulate disc cutters. The paper concludes by proposing a new approach to rock excavation by hybrid cutting based on controlling the primary crack orientation.

Jan 1, 1992

Comparing Energy Efficiency of Multi-Pass High Pressure Grinding Roll (HPGR) Circuits With increased emphasis on reducing costs and carbon emissions in mineral processing, it is becoming essential to employ the most efficient comminution devices and to use them to maximum effect. High pressure grinding rolls (HPGR) are considered highly efficient compared with other devices, however their relative efficiency in multi-HPGR circuits is less well understood. A series of comminution tests was carried out to evaluate three multi-pass HPGR circuits and a jaw crusher-ball mill circuit. Combinations of HPGR units (1.0 m and 0.25 m diameter), jaw crushers and Bond ball mills were used to grind a 32 mm top size porphyry copper feed (BBWI = 12.1) to a product P80 size of about 150 ¦m. Up to three passes of HPGR were used in each circuit, with energy measurement and size analysis at each point in the comminution process. The energy efficiencies of individual comminution stages and of the overall circuits were quantified and evaluated using three different approaches. The operating work index method for comparing comminution energy efficiency underestimated HPGR performance due to the large amount of fines generated. The -75 ¦m efficiency factor and F50/P50 reduction ratio interpolation methods both give a fairer measure because they better take into account the amount of fines generated by HPGR. The results show that the relative comminution efficiencies of the three multi-pass HPGR circuits tested differ by as much as 22%, providing insights as how to best employ HPGR in a comminution circuit. The most energy efficient of the circuits tested was a three-pass HPGR circuit with a 1.0 m diameter roll on the first pass in closed circuit with an 8 mm screen followed by a second and third pass in a 0.25 m roll.

Sep 13, 2010

The Electricity Generating Authority of Thailand (EGAT) Mae Moh coal mine is an open-cut coal mine in Thailand that produces about 16 Mt of lignite annually to generate 2400 MW of electricity. The surface mine pit covers is 4 km by 7 km with mining depths ranging up to 260 m. A large pit slope is formed with the progression of the mining operation. However, massive slides in the pit slope occur often due to the existence weak planes such as faults and bedding, and the weak mechanical properties of the rocks. Hence, 200 m to 300 m boundaries of rock block including coal seams are left in front of faults in order to prevent slides and maintain the stability of the pit slope. As a result, there are significant coal reserves beneath the abandoned area along the pit slope. Moreover, the mined coal seams are very thick and their thickness range from 15 to 30 m.This paper discusses the application of multi-slicing highwall mining system with stowing to this very thick coal seam left around large pit slopes by means of numerical analysis.

Dec 6, 2010

By J. R. Menasce

Mechanization in low-stope panels situated in hard rock infers roof support by tensile bolting to allow free passage of trackless mining equipment in the production areas. This is in sharp contrast to conventional mining, where compressive roof supports?such as timber and grout packs?have traditionally been used, up to 1.5 metres from the production face. Bolting is a hazardous operation because material is dislodged from the roof during the drilling activity. Even with temporary roof support installed, small pieces of rock are dislodged by the percussive action of the drifter. Operations with the man situated directly under the drill, during the drilling activity, are hazardous. The only way to remove the hazard is to move the man away from the machine for as much as possible throughout the complete cycle Costs associated with safety cannot be quantified, but need to form part of the decision-making process. Machine selections based on purchase and running costs alone do not justify the investment cost of mechanized bolters. The equipment selection process needs to take into account the total cost of mining as well as the human safety impact and loss of production costs from having to re-bolt roofs in a production panel to prevent falls of ground. Labour costs in mechanized low-stope bolting are between one-quarter and half the labour costs of non-mechanized bolting. This paper reviews the mechanized bolting option versus handheld bolting from a mining process and cost perspective in a hard rock, low-stope room-and-pillar mining operation in the platinum and chrome industries.

Jan 1, 2006

By Anthony Iannacchione

Designing coal pillars to provide resistance against overburden loads has long been an aim of rock mechanics engineers. The need for accurate pillar strength models has become more urgent as greater overburdens are encountered and pillar sizes grow larger. Current pillar design models differ widely in their predictions of the trend in pillar strength with increasing pillar width-to-height ratio. The goal of this paper is to evaluate current pillar strength theories, using a comprehensive data base of stress measurements from coal pillars. The stress measurements indicate that coal pillars maintain relatively high stresses near the ribline, and that the stress gradient within the yield zone can be approximated as a straight line. Several problems are identified for further research, including calibration procedures for different types of stress cells, strain softening behavior in the yield zone, and measurement of stresses in the cores of very wide pillars.

Jan 1, 1992

By Brian P. Waagner

Construction law in general and the law of deep foundations in particular continues to develop rapidly, particularly in the areas of risk allocation. Public and private owners are increasingly using contractual disclaimers to shift the risk of differing site conditions to contractors, and courts are increasingly willing to enforce these contractual devices. Perhaps also in an effort to control costs, public and private owners are turning to design-build contracting techniques. While design-build offers many advantages over traditional project delivery systems, it does not answer all of the risk-allocation questions that frequently arise. Even in design-build, problems with unanticipated subsurface conditions and defective design are not easily addressed. Finally, developments in electronic commerce present the potential to transform the construction industry.

Jan 1, 2002

By Lewis Robert M.

The importance of phosphate in feeding the people of the world has been recognized by mining companies as they continue their search for new ore deposits and ways of improving phosphate production. An extensive phosphate-recovery research project involving investigation of beneficiation variables by batch testing, flotation pilot-plant processing of the major portion of the ore, gravity separation of the coarse fraction, and recovery of byproduct heavy minerals of a North Carolina phosphate deposit has been completed. Data obtained through batch tests enabled the development of an economical flowsheet which proved successful for the efficient recovery of a good quality phosphate concentrate in a pilot plant.

Jan 1, 1975

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the' Bureau of Mines since 1917. The analysis published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By B. J. Moore

This publication contains routine analyses and related source data for 528 natural gas samples from 21 States collected during calendar year 1965 as part of a continuous survey of the United States for occurrences of helium in natural gas. This survey has been conducted by the Bureau of Mines since 1917. The analyses published herein were made by mass spectrometer and a special helium analysis apparatus, which are described in Bureau of Mines Bulletins 4863 and 576.4

Jan 1, 1966

By Ghosh I, Vanangamudi M

Experiments have been made in a laboratory heavy media separator at various specific gravities of separation using zinc chloride solution and magnetite suspension as media for different types of coals. The results indicate that the magnetite bath gives at better separation than zinc chloride solution. Even though the probable error remains the same for most conditions of operation, the error area is found to have a wide variation which emphasises the importance of the error area over probable error in evaluating the performance of a cleaning unit.

Jan 1, 1981

Recently, work was carried out by the Shotcrete Working Group to study anisotropy in steel fibre reinforced shotcrete using strain-controlled, compressive strength testing methods. The shotcrete materials used and specimen preparation procedures as well as testing methods are described. The test results are discussed and it is concluded that, because of the anisotropic nature of fibre reinforced shotcrete, it may be worthwhile investigating the degree of such anisotropy in practice using strain-controlled, strength testing techniques.

Jan 1, 2001