Search Documents

By A. C. Fieldner

The Sectional Committee on Classification of Coals, functioning under the sponsorship of the American Society for Testing Materials and the rules of the American Standards Association, in its 1934 report recommended to the American Society for Testing-Materials5 that Specifications for Classification of Coals by Rank be adopted as tentative. These specifications, slightly modified as recommended by the Sectional Committee, in its 1935 report,6 wore approved as tentative standards by the society in 1935. The specifications rover the classification of coals according to their degree of metamorphism, or progressive alteration, in the natural eerie s from lignite to anthracite. The basic scheme of classification is according to fired carbon and calorific value (expressed in B.t.u.) calculated to the mineral-matter-free basis. The higher-rank coals are classified according to fixed carbon on the dry basis, and the lower-ran]: coals according; to B.t.u. on the moist basis, that is, containing its natural bed moisture but free of visible surface moisture. Agglutinating and weathering indices arc used to differentiate between certain adjacent groups.

Jan 1, 1935

When the mining and milling of 1100 copper orebody commenced at Mount Isa a satisfactory grade of copper concentrate was difficult to produce. The major concentrate contaminants were fine pyrite and silica, particularly in the minus 10 microns fraction. Studies of the 1100 orebody showed that much of the fine grained pyrite and a proportion of the silica present in the ore contained carbonaceous matter in the form of complete or partial rims and as internal carbon films disseminated throughout grains. The hydrophobic surface property of the carbonaceous material resulted in inherently flotable fine pyrite and siliceous particles.The addition of a 60:40 mixture of nigrosine and dextrine, initially to a prefloat concentrate of the inherently flotable carbonaceous material and finally to the total copper flotation feed, successfully controlled the flotation rates of the carbonaceous pyrite and silica. The objective of a 25 per cent Cu concentrate grade was then achieved without decreasing copper recovery.

Jan 1, 1971

By M. Kawakami, K. Suzuki, T. Takenaka, S. Yokoyama

Molten NaNO3-NaNO2-KNO3mixture is used as a heat transfer medium at high temperature. One of the most important properties of this mixture is the heat capacity. In the present work, the enthalpy change with temperature was measured by the drop calorimetric method to evaluate the heat capacity. The results are summarized as follows: The enthalpy of the mixture increased linearly with the temperature. From the slope of the line, the heat capacity was evaluated. The heat capacity of pure NaNO3, NaNO2and KNO3was 0.129,0.110 and 0.142 kJ/mol/K, respectively. These values are in fairly good agreement with the published data. In the binary and ternary systems, the molar additivity of heat capacity, which is well known as Neumann-Kopp’s law, was obtained. The heat capacity of HTS1and HTS2, which are well known ternary mixtures of practical use, were in the range of published data.

Jan 1, 2004

By Olliver J. G

Over 400,000 tonnes of kaolin, sillimanite, mica, kyanite, feldspar and rutile have been mined from the unique Williamstown orebodies since their discovery in the early 1900's. Numerous companies; both large and small were associated with the early development of these deposits but since the formation of Australian Industrial Minerals in 1947, this company has been the only significant producer. A combination of mining and management problems almost forced closure of the mine in the late 1970's but this was averted by a changed attitude towards mine planning. Mine development is now based on detailed geological and technical investigations, exploration for additional ore reserves is being conducted and laboratory and pilot scale studies are being undertaken to utilise both low grade ores and waste materials. The professional approach to mine and market development will ensure that Williamstown mineral products will continue to be available for many years.

Jan 1, 1989

By R. S. Dean

[During the past year the Metallurgical Fundamentals Section gave about an equal amount of time to the experimental determination of fundamental thermodynamic constants and to the demonstration of the application of such data to more directly practical metallurgical problems. The first division of the work - the actual experimental measurements of typical thermodynamic constants - was carried out an two problems, termed ?continuing? programs, namely, (1) measurements of Specific Heats at Low Temperatures and (2) Measurements of Heats of Formation and Free Energies. Specific substances chosen for investigation are classified as (n) those that have been the subject of requests for information from the industry and that, upon examination, seem of sufficient practical importance to justify study, and (b) compounds that are difficult to treat metallurgically, or whose specific thermodynamic properties have not yet been determined satisfactorily and for which accurate data might suggest improved or new methods of Metallurgical treatment, or (c) materials recognized as belonging to a social class with exceptional thermodynamic properties and, hence, of scientific as well as technical importance.]

Jan 1, 1938

By N. W. Johnson

"Two analysis tools which have been applied to problems in industrial flotation processes are the application of kinetics and detailed mineralogical or liberation data, both on a size-by-size basis. This paper describes practical examples of the application of kineticsto examination of the entrainment recovery mechanism, the retardation of valuable minerals at the commencement of flotation sections and the resolution of problems related to valuable species with reduced rate constants at the end of sections. Examples of the usefulness of size-by-size liberation data for monthly composite samples of products from a concentrator are also described.IntroductionMuch of the published industrial flotation data on the behaviour of minerals in various size fractions have been obtained from specially conducted surveys with a duration of several hours. Such data are very valuable and provide a record of the behaviour of the entire flotation plant or sections during the interval of the survey. Some examples from the literature can be cited Cameron et al. (1971), Lynch et al. (1981), Frew (1982). Less attention has been given to the value of complementary sized data derived from compositing shift or daily inventory samples over an interval of one or several weeks with repetition of the procedure at the completion of each interval. Mineralogical point count data of the size fractions of such samples and data interpretation are rare in the literature.Kinetic data on the behaviour of valuable and gangue minerals in various size fractions have been reported often for flotation banks. In the experience 0 f the writer, there has been a tendency among operating metallurgists to ascribe problems in the flotation process to rate constant values for gangue minerals which were believed to be unsatisfactorily high. Less attention has been paid to the value for the rate constant for the valuable mineral over the length of a particular bank.Examples of the types of data which were mentioned previously have been obtained from the lead-zinc concentrator at Mount Isa Mines Limited. The various types of data have been collected to evaluate their worth in order to provide relevant information for both research and operational aspects of the plant."

Jan 1, 1987

By Richard Rice

TURBO blowers for blast-furnace blowing have now been in use for some years, and a review of the experience gained and the present state of progress may be interesting. FIG. 1.-STEAM TURBINE DIRECT CONNECTED TO AIR COMPRESSOR. The first blast-furnace blowing engine of this type to be installed in America was built by the General Electric Co. and is installed at the oxford Furnace of the Empire Iron & Steel Co. This machine was put into operation March 8, 191.0. A duplicate unit is situated at the furnace of the Northern Iron Co. at Port Henry, N. Y., which unit was put into opera ion June 30, 1910 (Fig. 1).

Jan 5, 1914

By Slechta J. J

An evaluation of a pilot scale Delkor horizontal belt filter at Bellambi's South Bulli Colliery showed high productivities and low moisture contents for a range of feed slurries. When treating flotation concentrate, a productivity in excess of 1000 kg/m2/hr (dry) at a moisture content of less than 22 per cent was obtained. The results indicated the belt filter had a capacity twice that of conventional drum or disc filters, and was capable of dewatering a very fine, thickened, classifying cyclone overflow slurry to an acceptable moisture content. The superior performance of this filter is discussed in terms of the factors influencing cake formation and the stratification of solids in the filter bowl of a conventional rotary vacuum drum filter.

Jan 1, 1986

By M. Dworzanowski

The physical beneficiation of iron ore that has a wide particle-size distribution is problematic, regardless of the process applied, whether dense medium separation, gravity concentration, magnetic separation, or flotation. The problem of particle size is further compounded when there is a significant -10 µm fraction. Generally the approach to a wide particle-size distribution is to split into narrower size ranges and treat each separately. More often than not the -10 µm fraction is not treated but discarded. This approach results in a more complicated and expensive flow sheet and the loss of any potential value in the -10 µm fraction. Wet high-intensity magnetic separation (WHIMS) bench-scale test work was conducted on a haematite-rich material with a particle size of -200 µm. What made this material different was that it contained a 60% -10 µm fraction, hence discarding the -10 µm material was not an option. The objective of the test work was to determine how to maximize the recovery of the haematite across the full particle size range. Given the unusual particle size distribution, it was concluded that WHIMS would be the only practical beneficiation route. The -200 +10 µm and -10 µm fractions were treated separately and together under varying WHIMS conditions. For a given concentrate grade, the mass yield obtained was greater when the total particle-size distribution was treated. The inferred optimum conditions, using the same material, were tested on a pilot-scale WHIMS and similar results were obtained.

Jan 1, 2014

By William D. Leech, Ronald E. Romley, Gary N. Sheppard

The Price Road Drainage Tunnel was constructed for the Arizona Department of Transportation (ADOT) in 1988 and 1989 to provide surface water drainage for the proposed outer Loop Highway (SR 117). The 5.4 km (3 mile) long, 6.6 m (22 ft) excavated diameter tunnel was driven through sand, gravel and cobbles utilizing an open face digger shield. Precast concrete segments were erected for initial ground support. A second-pass reinforced concrete final lining was placed, which was followed by contact grouting. This paper will consider the owner's representatives' view of the effectiveness of using precast concrete segments for this project. Topics discussed include segment design and erection, ground support, geotechnical instrumentation, segment erection verses contact grout interactions and tunnel production.

Jan 1, 1991

By H. S. Price, J. C. Cavendish, R. S. Varga

A numerical formulation of bigh-order accuracy, based on variational methods, is proposed for the solution of multidimensional diffusion-convection-type equations. Accurate solutions are obtained without the difficulties that standard finite difference approximations present. In addition, tests show that accurate solutions of a one-dimensional problem can be obtained in the neighborhood of a sharp front without the need for a large number of calculations for the entire region of interest. Results using these variational methods are compared with several standard finite difference approximations and with a technique based on the method of characteristics. The variational methods are shown to yield higher accuracies in less computer time. Finally, it is indicated how one can use these attractive features of the variational methods for solving miscible displacement problems in two dimensions. INTRODUCTION The problem of finding suitable numerical approximations for equations describing the transport of heat or mass by diffusion and convection simultaneously has been of interest for some time. Equations of this type, which will be called diffusionconvection equations, arise in describing many diverse physical processes. Of particular interest here is the equation describing the process by which one miscible liquid displaces another liquid in a one-dimensional porous medium. The behavior of such a system is described by the following parabolic partial differential equation:

Jan 1, 1969

By Wellington Pereira Inácio

This work investigated the toughness behavior of polyester matrix composites reinforced with up to 30% in volume of long, continuous and aligned sisal fibers by means of Charpy impact tests. It was found that the addition of sisal fibers results in a marked increase in the absorbed impact energy of the composites. Macroscopic observation of the post-impact specimens and SEM fracture analysis showed that longitudinal rupture through the sisal fiber interface with the polyester matrix is the main mechanism for the remarkable toughness of these composites.

Jan 1, 2010

By T Atkinson, A Cobb, R AJIington

Risk management is concerned with the whole spectrum of financial, geological, engineering, legal, governmental, social and occasionally ethnic issues, concerned with mining projects. The inherent risks in mining operations are well publicised, but new issues and hazards arrive on the scene and lake precedence, but the older risks still remain, while insurance cover may not he ‘full cover’ in the future. It has long been recognised that quantitative approaches to risk analysis can play a major role, but although these methods are capable of considerable theoretical precision, the lack of sound risk input data and experienced personnel limits the usefulness of theoretical analysis. It can, however, greatly assist in comparing cases, in identifying areas of risk and help in the investment decision process. Its major contribution to a mining project is that it imposes an investigative discipline that also assists in improving the quantitative approach to risk analysis and hence risk management. Risk analysis and risk management also requires sound common sense and major inputs from experienced geologists, mining, mechanical, electrical and mineral processing engineers. The Engineering Council, in 1992, issued a ten point code of professional practice entitled ‘Engineers and Risk Issues’ (The Engineering Council. 1992), covering our professional responsibilities, the law, our conduct, the need for a systematic approach to risk issues, the use of professional judgement, communications, risk management, evaluation of risk, our professional development in this field and the encouragement of public awareness of risk issues. This is a specific area of training perhaps long neglected by our industry and academic institutions (Atkinson. 1983).

Jan 5, 1996

By Steve Dillingham

There are some blasters and blasting companies that just seem to have better safety reputations than others. This is in spite of the fact that they are essentially doing the same type of work under similar conditions. To achieve that enviable safety reputation, it simply comes down to a strong safety culture prompted by a responsibility for others, as well as yourself and your company.

Jan 1, 2003

The University of New South Wales (UNSW Australia) has been a world leader in the development of innovative virtual reality technologies over the last 15 years. AVIE (Advanced Visualisation and Interactive Environment) was developed by iCinema as a collaborative venture between UNSW?s Faculties of Engineering and the College of Fine Arts. This is the world?s first 360°-surround, virtual reality (VR) stereo projection theatre system. The School of Mining Engineering at UNSW Australia has developed 18 different virtual reality modules aimed at mine safety training and mining engineering education. These modules are being regularly used in both the mining industry and the university. The School of Mining Engineering is continuously involved in the development of different modules. Research is also currently being conducted on the implementation of other technologies into this environment. Artificial intelligence (AI) and fuzzy logic are tools that the authors would like to consider implementing in future module development. This paper will review current research in both these areas and consider options for applying these technologies.

Jan 1, 2014

The effect of conditioning energy input on the metallurgical results of an emulsion flotation process has beenattributed by previous authors to a detergency process.This paper shows that such a process does not explain the data and that an attrition mechanism is more appropriate.

Jan 1, 1970

PERSPECTIVE ?Natural resources exploration, extraction and beneficiation is complex and challenging: ?Input costs rising, complexity increasing, rising stakeholder management needs, regulatory compliance issue, etc. ?With increasing costs and complexity of managing operations are we simply getting less bang for our buck?

May 1, 2013

Copper mineralization associated with minor molybdenum, silver, and gold occurs in a hydrothermally altered brecda within a granodiorite mass of Upper Permian age. A dyke system of rhyolite, dacite, and andesite forms plug-like bulges near the breccia and probably caused mineralization as a late stage effect.Base metal sulphides occur as disseminations, fracture and cavity fillings in the breccia. A pyritic halo in hydrothermally altered granodiorite surrounds the breccia and grades into unaltered granodiorite. Drilling during 1969 indicated the grade is subeconomic.

Jan 1, 1972

By M. J. Allan

"The paper describes the author's experiences in the startup of autogenous and semiautogenous grinding circuits gained over the last twenty years on both large and small grinding circuits. Typical phases in commissioning from construction to startup with ore are covered. The paper also describes experiences with material handling systems, slurry pumping, vibrating screens, trommel screens and pebbles crushing systems. INTRODUCTIONThe commissioning of any new mineral processing plant is an important and exciting milestone in any project. It is at this point in time that the efforts of developers, design engineers, equipment suppliers and operators culminate in a finished product. The successful completion of any project requires that the plant achieve design throughput as quickly as possible. The success of any startup can generally be anticipated by the amount of careful planning which takes place before equipment is operated. The first part of this paper describes the steps in going from construction through to introduction of ore. The organization and planning of startup activities is also covered.The second part of this paper describes some typical problem areas and past experiences in the startup of semi-autogenous grinding circuits. Semi-autogenous grinding circuits present some special challenges in the startup phase. The description of some of these problems and experiences will hopefully provide other operators with suggestions on how to avoid (or at least prepare for) these problems."

Jan 1, 1992

By Esher Hsu

Keywords: Recycling, Consumer Battery, Fee rates On November 11, 1999, all types of spent consumer batteries are proclaimed to be collected in Taiwan. Under current recycling system, all producers and importers of consumer batteries have to pay a collection/recycling fee to the Recycling Management Fund (RMF) of EPA based upon the rate approved by EPA. Collectors and recycling plants receive subsidies from RMF according to the collected and treated amounts audited by an independent auditing organization. Collected spent consumer batteries only reached 923 tons in 2002 equivalent to 10% of the total quantity sold at the same year. How to increase the collection efficiency of used batteries becomes an important issue for EPA in Taiwan. The objective of this study is to explore current recycling system of spent consumer battery in increasing collection efficiency. Results provide some suggestions to Taiwan EPA regarding recycling route, recycling system, recycling rates, and recycling subsidies.

Jan 1, 2005