Search Documents

By Lorenzo Pellegrini

The respect of EPB reference pressure during TBM advance and hyperbaric activities, the complete and effective filling of the annular gap between tunnel lining extrados and the excavation section and a well organized monitoring system, to control surface settlements and ground distortion, are items of utmost importance in EPB tunnelling process. The paper describes how these concepts have been applied while excavating in the difficult underground conditions found at Sao Paulo (Brazil) during the execution of the Sao Paulo Metro Line 4-Lot 1. In this project, the annular gap has been filled by two components type, cement grouting. The back feed of the extensive monitoring campaign carried out to check the surface settlements during the excavation and hyperbaric maintenance operations will also be described in the paper.

By Y. C. Liu

Both the habit plane of martensite and the orientation relationship between the matrix and martensite platelets of different habit planes have been investigated in binary titanium alloys with molybdenum, chromium, and iron. The effect of the mode of deformation on the martensite habit plane was studied. A micrograph of an exposed mar-tensite platelet is presented. IN the study of martensitic transformation in Ti-Mn alloys,' two martensite habit planes—{334), and {344)8—were reported. The {334), habit was also observed in unalloyed titanium upon transformation,' although there is disagreement with respect to the exact indices. The other habit plane, {344),, has not been reported in martensitic transformation in any other alloys. The present investigation was made to determine whether other binary titanium alloys with P-stabil-izing elements would exhibit a crystallography of transformation similar to that of Ti-Mn alloys. Furthermore, since martensite platelets can be induced by deformation under certain conditions, it was of interest to investigate whether the mode of deformation, compressive or tensile, would influence the formation of martensite platelets on a specific plane in an alloy system which possesses two martensite habit planes. Experimental Procedure The material used for the preparation of the binary alloys of iodide titanium with molybdenum, chromium, and iron had the following purities: 99.99 pct iodide titanium, 99.9 pct molybdenum, 99.423 pct chromium, and 99.9 pct iron. The compositions of alloys listed in this paper are in nominal weight percentage. All specimens used were prepared and treated according to the procedure described in reference 1, unless stated. For the subzero temperature treat,ment the following experimental schedule was followed. After specimens had undergone the grain-growth treatment, they were quenched into an ice-water bath and were then metallographically examined. In specimens of higher alloy content, no martensitic transformation was observed. In those in which mar-tensitic transformation did occur, only specimens in which the martensite platelets existed as fine needles in localized regions were used. All specimens were reannealed 17 hr at 1200°C, quenched into ice water. and the capsule was broken. They were held in the ice water for from 5 to 10 sec, then transferred to a liquid-argon bath. This stepped quenching procedure was found to be more efficient than direct quenching into liquid argon. In the latter case, as soon as the hot specimen was immersed in the liquid argon, a protective, insulating layer of argon gas formed, and the specimen continued to glow vividly in the bath for some time. In the study of the habit behavior of martensite produced by deformation, specimens were deformed at room temperature either by compression, tension, or rolling. Martensite habit planes were determined by the two-surface analysis procedure described in reference 1. A stereographic net of 153/4 in. diam was used throughout the investigation. The method for determining the orlentation relationship between martensite and the matrix follows that used by Greninger and Troiano.' A diamond-polishing table with its auxiliaries was used in order

Jan 1, 1957

By M. W. Hildyard

A blast was engineered close to a tunnel in a deep-level mine with the purpose of studying the wave interaction with the tunnel. Numerical modelling of seismic wave propagation was used in both the forward planning and the back-analysis of this experiment. This paper presents the forward analysis. A likely model for a propagating blast was investigated and developed. This model predicts the influence of the velocity of detonation of the blast and the rise-time of the blast on the radiation pattern, and hence on the expected positions of maximum velocity at the tunnel surface. An attempt was made to quantify the parameters of the blast model, using waveform data from two other blast experiments. The blast model caused particle velocities which were an order of magnitude lower than these measured velocities. Large values for blast pressure were required to match the amplitudes of the recorded velocities. An alternative ?effective? source with a similar mechanism but increased diameter was proposed to account for the higher velocities. It was established that distant velocities scale with the square of the borehole diameter. A calibration blast at the experimental site was also modelled. Agreement in the waveforms was not sufficient for conclusive statements to be made about the validity of the source model. However, the modelled waveforms show an encouraging correspondence with some measured waveforms. This gave confidence that the model could be used to examine wave propagation around the tunnel, and allowed a scaled source to be developed for forward analysis of the main experiment.

Jan 1, 2001

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

Tougher physical mining and processing conditions as well as economic circumstances are causing many mining companies to re-evaluate the effectiveness of their mine planning. The recent wave of inexpensive computing power provides the engineer an opportunity to go beyond the simple one-off manual mine design and production schedule. The basis of a good mine plan is a good reserves model. Concepts of mine model development are explored. The only advanced computer methods that have found consistent success in optimising mine planning functions are economic pit limits determination and material scheduling. Three pit 'optimisation' methods are examined; the moving cone, the Lerchs-Grossman 3-D graph algorithm, and the new network flow algorithm. A comparison between the methods in terms of total profits generated and computer time involved are made. The results show that both algorithms produced a higher profitability than the simple moving cone, but at much higher execution times. However, the profit increase never exceeded much more than 1 % of the base moving cone case. Finally, a method for the development of long range material production schedules with forward waste planning is presented.

Jan 1, 1989

By Jean-Michel Rendu

Computer systems are an integral part of the mining industry. Before a new operation is started, software requirements, and the need for hardware and communications must be determined. The personnel required to use the software, and to support the necessary infrastructure, must be hired and trained. In this sense, this paper emphasized the needs that geologists and mining engineers have for technical software. Similar requirements apply to all other aspects of a mining operation. These requirements will become even more critical in the years to come, and must be fully assessed before construction of a new mine begins. Dependency of a mine operation on its computer systems must never be underestimated.

Jul 17, 2000

By M. C. Villeneuve

A numerical modelling approach was developed to explicitly simulate geomechanical characteristics of intact rock: mineralogy, grain size and fabric. The approach involved creating a representative constitutive model for each of three common rock-forming minerals: mica, quartz and feldspar. The constitutive models developed are valid within the low confinement realm of excavation boundaries, where tensile fracture processes dominate. The mineral types were assigned to numerical elements, which were associated with each other through an algorithm created in a finite difference model, FLAC 2D (Itasca 2007a), to simulate real crystal geometries and orientations. The numerical models were used in a parametric investigation of the geomechanical characteristics and compared with published observations of the rock yielding process in laboratory testing. This approach has allowed the explicit grain-scale investigation of the impact of geomechanical characteristics on rock yielding at low confinement, leading to an improved mechanistic understanding of excavation-scale rock yielding processes at excavation boundaries.

May 1, 2009

Underground mine planning is characterised by a series of designs, starting with prefeasibility and culminating in operational. Information on the mineralisation and geotechnical conditions is available in increasing levels of detail, as development occurs. In the recently completed AMIRA Planning and Rapid Integrated Mine Optimisation (PRIMO) project, a methodology for producing good strategic and then tactical designs using new optimisation tools, was developed. At the strategic level, fundamental decisions must be made such as those relating to cut-off grade, bench heights, mining methods, access and haulage systems, properties of the mill, etc. The inputs are the block and financial models, geotechnical data, infrastructure and production costs, etc. Stope definition for strategic designs includes bench RLs (relative levels), orebody envelopes, and design and placement of amalgamated or simplified stopes. If multiple mining methods are under consideration, then stopes need to be associated with these. Access design must take into account decisions such as declines versus shafts, a template for level layouts and the topology of the access network. Some of the geotechnical and physical constraints are relaxed for strategic design stages. Strategic scheduling is high level, from a month to a year at a time. In the PRIMO project, software tools have been developed enabling the mine planner to rapidly produce a large number of such strategic designs. After the designs have been evaluated, the highest value designs are chosen and a small number of these can then be further refined at a tactical level. For these designs, the first step is determination of all stopes meeting physical and geotechnical requirements and constraints, allowing for complex stope shapes. Next, detailed layout of the mine access network is obtained, satisfying all operational and geotechnical constraints. Finally, more detailed scheduling is performed, over shorter time periods. The Melbourne University group has focused on optimal access design. In particular, the access network is optimised for minimum cost, taking into account the cost of haulage and development over the lifetime of the mine. Costs vary over the different parts of the network depending on the quantity of haulage and so a weighted network optimisation problem has to be solved. We have developed two software tools for this task, decline optimisation tool (DOT) and planar underground network optimiser (PUNO). DOT produces an optimal network of declines and crosscuts connecting access points on the levels to a portal or break-out point from existing infrastructure. PUNO designs the level layout, including footwall and hanging wall drives, development drives and connections to vent raises. A survey will be given of the capabilities of DOT and PUNO when used on some recent case studies. Our current goals include incorporating some aspects of ventilation design and modelling the development costs when additional ground support is required. This is an abstract only. A full paper was not prepared for this abstract.

Dec 6, 2010

By Helen D. Robinson

The seawalls that surround Ellis Island were constructed in the early 1900s and now show varying degrees of deterioration. An innovative approach to the structural repair of the seawalls was developed, which consisted of the use of micropiles for stabilization of vertical and horizontal seawall movements. The micropiles were installed through the existing seawalls and penetrated through a thick overburden, consisting of soft alluvial deposits and relatively hard glacial till, and were bonded into Manhattan Schist. Drilling of the micropiles often encountered timber and other obstructions. The selection of micropiles for stabilization of the seawalls offered significant advantages over other foundation systems and over alternative soil improvement techniques. They allowed drilling through a variety of materials without the need for significant retooling or changes to the drilling procedure. This reduced the impact of foundation construction on the sensitive historical landscape and structures, and prevented the need for significant foundation work from the water side of the seawalls. In addition, micropiles offered relatively high installation rates and flexibility to adapt to the varying conditions along the seawalls.

Jan 1, 2008

The mechanization of the coal industry in New South Wales involved the introduction of large face and transport machines. The trend is towards still higher capacity units with .greater horsepower and it became apparent that a potential risk of damage to the hearing of workmen existed. In order to assess whether the sound levels were SUfficiently high to impair the hearing of workmen a sound level survey of all major operations in the industry was carried out by the Mining Engineering Division of the Joint Coal Board.The results indicated ·that the operations could be classified into three categories of risk, probably hazardous, of doubtful hazard due to the intermittency of the operations, and of low hazard.Legislation has subsequently been enacted requiring the wearing of hearing preservation aids in some of the probable risk operations.

Jan 1, 1974

By Schlanger H. P

A theoretical model for gas outbursts in underground coal mines is as follows. An outburst is the structural failure ofcoal due to excess stress resulting from body forces caused by gas pressure gradients. These body forces influence the stability of a mine face in the same manner that gravitational body forces affect the stability of the roof of a mine. The magnitude ofthese body forces can be appreciated when it is realized that for an average density coal, the gravitational body force is equal in magnitude to the force from a gas flow with a pressure gradient of 14 kPa m-I. Gas pressure gradients and the resultant stresses within a seam can be calculated with numerical methods. Thus, providing the necessary parameters can be measured or estimated, in principle the theory can be applied to compare the outburst risk of various mining arrangements.

Jan 1, 1985

By Dhar B. B, Gupta R. C

Grinding of iron ore is an essential step to utilise ore fines for pelletisation needed for DRI units. While preparing iron ore pellets for DRI production, the iron ore needs extensive grinding which is highly energy consuming step causing the process to become non-viable in some cases. In the present paper an attempt has been made to evaluate grinding performance of thermally treated ore compared to normal ore grinding. Such thermal pre-treatment has been found to reduce the energy requirement with lower consumption rate of grinding media. It has been observed that by applying thermal shock the ore is rendered weak with improved grindability. The stresses generated due to thermal treatment may extend existing micro-cracks in the ore and in some cases it may even nucleate fresh cracks. Experimental studies carried out on thermally treated hematitite ore reveals that the heating to 400¦C followed by water quenching can cause a reduction of 45 per cent in grinding energy. The paper gives the details of the experiment and the Results.

Jan 1, 1999

In considering the preparation of any paper concerning bearing metals, one feels a certain amount of diffidence in venturing into a field which has been capably explored at great length and in great detail during recent years. Many excellent articles have appeared in technical literature, dealing with the general theory of bearings and of bearing metals, the properties of white metals of the tin-base and lead-base types, and of the recently developed lead-bronzes.The justification for this further excursion into the field lies in the fact that it treats a branch of the bearing metal family which has so far received very little attention, and that of a somewhat sketchy nature, in published papers.The author's object is to give some outline of the history, development, present status and possibilities of the cadmium-base bearing metal alloys, particularly those in which copper is the main alloying element.GENERAL CONSIDERATIONS.It is desirable that attention should first of all be given to the general theory, constitution, and necessary attributes of bearing metals, in order that some of the problems met with during the development work may be better appreciated.Despite some evidence to the contrary, it is fairly generally maintained that an alloy for bearing metal use should be of a heterogeneous nature. It should consist of particles of a hard constituent uniformly distributed through a softer matrix.The basic idea is that the hard constituent should actually bear the load and resist wear, while the matrix imparts the necessary ductility and allows the bearing to align itself on the shaft in service.

Jan 1, 1934

By C. M. Rule

Energy efficiency is currently a significant area of interest due to the Eskom power situation, which led to severe power impacts to the PGM, and indeed whole SA primary industries, in early 2008. Anglo Platinum has focused on energy efficiency for a number of years, especially in the concentrator operational area. New comminution technologies have been aggressively developed, which have shown real metallurgical efficiency gains as well as significant energy efficiency and saving potential for Anglo Platinum?s total electrical consumption as the company expands into a growing PGM demand market. This paper illustrates this programme?s activities, potential and considerable achievements to date.

Jan 1, 2009

By Lee W. Abramson, Kenneth P. Akins

The authors have accumulated published data on residual soil and rock tunnels in the United States and have compared it to transit tunneling experience in Atlanta, Georgia, and tunnels in other soil and rock conditions. Two 6.1 meter (20 foot) diameter shield driven, compressed air tunnels were constructed for the Metropolitan Atlanta Rapid Transit Authority (MARTA) connecting the Five Points Station (central hub) with the Peachtree Center Station (first station on the north line). Because of the historic multi-story structures above the tunnels and the variety of subsurface conditions, a comprehensive ground monitoring and observation program was conducted. Conclusions are drawn regarding residual soil and rock ground response due to tunneling. Comparisons are made to ground response due to tunneling in other soil and rock conditions.

Jan 1, 1983

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of the cementation of cadmium, lead, and silver from dilute aqueous solutions. This work is an extension of studies carried out on the Cu-Zn and Cu-Fe systems for which the reaction rate was found to be completely solution phase mass transfer controlled.When the amount of material deposited was greater than 0·2 to 0·4 mg/cm2 there was an apparent enhancement in rate which is attributed to the formation of a roughened deposit. This same phenomenon was observed in the Cu-Zn and Cu-Fe systems. Again, the rate of reaction of each system investigated was found to be solution-phase mass transfer controlled.

Jan 1, 1971

By Kumar A, Mishra N. C

For each tonne of chromite ore mined in Sukinda, approximately ten tonnes of fine overburden material is generated. The overburden typically contains about 30 - 60 per cent Fe2O3, 0.3 - 1.1 per cent Ni, four to nine per cent Cr2O3 and 0.04 - 0.2 per cent cobalt and is being discarded leading to loss of valuable metals and creating environmental pollution. In order to take the advantage of presence of iron, nickel and chromium, the present studies advocate the utilisation of nickel lateritic chromite overburden for production of Ni bearing pig iron through blast furnace extracting maximum iron and nickel from the chromite overburden. The present paper deals mainly with the beneficiation of chromite overburden, sintering characteristics and thermodynamic studies. The beneficiation study shows that a beneficiated concentrate having Fe - 50 per cent and Ni -- 1.1 per cent can be achieved from chromite overburden having Fe - 30 per cent and Ni -- 0.7 per cent. Sintering studies have been carried out with bed height of 300 and 450 mm at a suction of 600 and 900 WG respectively. The results reveal that good quality sinter can be produced from chromite overburden concentrate with a basicity of about 1.0 and coke breeze consumption rate about 16 per cent. In all the experiments, Tumbler Index, Abrasion Index and Shatter Index was found to be in the range of 65 - 70, 4.5 - 5.5 and 85 - 90 respectively. The other parameters namely softening temperature, melt down temperature, reduction degradation test and relative reducibility have also been determined. A thermodynamic analysis has also been carried out to make a technological assessment of the process for the production of alloyed pig iron from chromite overburden in blast furnace which shows that it is possible to produce nickel bearing pig iron in blast furnace using the sinter up to 80 per cent. Techno-economic analysis reveals that this route will yield a substantial profit even after accounting for cost of beneficiation, extra coke, raw materials and extra slag produced.

Jan 1, 1999

By A. R. Katti

The stone columns are widely used in the improving the bearing capacity of weak soils mostly for supporting flexible foundation systems. The load carrying capacity of a stone column is complex in nature. The load capacity is derived from the lateral stresses acting on the stone column due to load transmitted from the flexible structure due to deformation to soil mass and which in turn transmits lateral pressure in s3 direction. The load capacity is also function of the f value of the stone column, cohesion of the surrounding soil, K0 and Gb2 of surround­ing soil including passive resistance developed to lateral deformation of the stone column. The assessment of axial and radial deformation is much more complex. Recently Katti et.al. have developed a method based on a granular heap approach and computed with equivalent fe. which combines the effect of s3a and equivalent volume concept to estimate radial and axial strains. In this paper an attempt is made to put forward guidelines for design of stone column accounting for both stability with respect to shear and also with respect to settlement. The estimate of settlement are based on the internal properties of stone column and surrounding soil. It is considered thus the settlements computed are more realistic.

Jan 1, 1996

By Georgene Renner, William R. Yernberg, Steve Kral

ABB provides integrated pro-cess control, optimization and information systems, drives and power-distribution equipment as well as other services and support to the mining industry. ABB also supplies electrical equipment and control systems for the openpit mining industry. This includes products for the automation of electrical equipment in mine shovels. The company offers low- and medium-voltage drives for various mineral- industry applications. And ABB provides gearless mill drives for equipment, such as semiautogenous grinding mills that are too large for conventional drives. ABB Industrial IT provides innovative hardware and software systems that cover all the requirements of the modern mining and processing plant.

Jan 1, 2004

By Changqing Su

A batch incubation experiment has been carried out to investigate the optimal condition for the microbial remediation of hexavalent chromium (Cr(VI)) in soils contaminated by chromate ore processing residue at Hunan Iron-Alloy Factory in China. The optimal condition was obtained by comparing the remediation efficiency of Cr (VI) by indigenous bacteria under different culture media, the quantity of nutrient sources, the pH and the temperature. The results indicated that glucose and yeast extract was the optimal component of culture medium and the quantities of the above components were 8 g L-1 and 13 g L-1, respectively. The optimal temperature and pH value were 30_ and 10.0, respectively. A bioreactor was operated under the optimal condition to evaluate the efficiency of Cr(VI) remediation in the contaminated soil. The result showed that water soluble Cr(VI) in soils was reduced from 320 mg kg-1 Cr(VI) of the initial concentration to below detection limit after 30 h in a bioreactor. Thus, there is a large potential to make bioremediation for the reduction of Cr(VI) to Cr(III) by the addition of optimal culture medium under aerobic condition.

Jan 1, 2010