Search Documents

By M. M. Rajkovich

Just prior to the close of the century, the Federal Mine Safety and Health Review Commission issued its long-awaited decision in Berwind Natural Resources, et al v. Secretary of Labor, to usher in the new millennium. The case arose as a result of a mine explosion in Eastern Kentucky resulting in MSHA’s issuance of 225 citations, not only to the contractor, but to four affiliated entities of Berwind Corporation. While an Administrative Law Judge dismissed those citations as to three of the Berwind entities, both MSHA and the remaining Berwind entity appealed the case to the Commission. Although the Commission effectively left intact the Administrative Law Judge’s decision, it announced a new theory of liability that would apparently be applied in the future, namely the Unitary Operator Theory. This presentation will provide an in-depth look into the Berwind decision and explore the means under which MSHA might impose liability for contractor violations upon other entities in the future.

Jan 1, 2001

By Fogarty J. G H

Ausmelt Technology has a unique capability of removing the impurities, phosphorus and sulphur, from the feed materials to the process. Sulphur is removed to the gas phase almost completely because of the interactions of ore and coal in the reaction region at the top surface of the slag bath. Phosphorus is removed to the slag phase, with both basic and higher, controlled iron oxide levels in slag being achieved in the process. The significance of these features of the process relate to the production of pig iron with very low levels of these impurities for the further processing to steel, and to the treatment of high phosphorus and high sulphur raw materials. The marketability of pig iron and the raw materials are discussed in relation to this feature of Auslron.

Jan 1, 1999

A general outline of the significant features in the quality and manufacture of the more common refractories is given. Where possible, linkage between quality development and control and service applicationhas been shown and explained. INTRODUCTIONThe refractory industry is no stranger to change. New processes and revision of old processes in other industries are the harbinger of new and revised products in refractories.Few of the changes are dramatic; generally they are evolutionary rather than revolutionary. New developments are additional to, and inclusive of, established practice.Therefore in this paper it is necessary to repeat much of what is already known in order to show the development taking place.FIRECLAY REFRACTORIESGeneral technology Fireclay refractories are the most common, the most varied and the most versatile of all refractories. Virtually any composition of silica and alumina up to the composition of kaolin is possible. For purposes of comparison they may be classified in the Continental fashion in accordance with chemical composition or in the American way according to "duty". That the two methods are equivalent is shown by an inspection of the alumina-silica diagram of Bbwen and Greig (1924). 'Fireclay refractories are composed of a glassy and a crystalline component derived from the chemical and physical nature of the raw materials used in their manufacture.

Jan 1, 1961

By Shaoxian Song, Ling Xia, Hongqiang Li, Yubiao Li, Yunliang Zhao, Shaobing Xie

Since human daily demands for fresh water have been increased significantly, the supply of fresh water for the mining industry, especially froth flotation, should be considerably reduced. In addition, stricter environmental standards have been implemented in many countries to reduce the risks due to the disposal of wastewater, many flotation operators have to seek more efficient ways to utilize the limited fresh water sources. Recycling water with high concentrations of impurities is a normal strategy for most of the mineral processing plants; however, water quality should be carefully considered to guarantee a smooth flotation process. Recently, the application of seawater in flotation has attracted much attention due to its availability and abundance rather than fresh water. However, the influencing mechanisms due to the application of seawater in flotation have not been fully understood especially the reactions between mineral particles and bubbles in the presence of high concentrations of cations and anions. This would impede the application of alternatives to fresh water in the flotation. Therefore, this paper reviews the current water sources and the technologies for water recycling in the flotation process. Specifically, the life cycle of water in flotation was proposed. In addition, the strategies including high pulp density flotation as well as the most promising alternatives to fresh water have been discussed in details, with the related mechanisms being demonstrated.

By Les Johnston

_ BACKGROUND - About EPCOR - Genesee Generating Station - Phase 3 Expansion _ TECHNOLOGY SELECTION - Selection Criteria - Combustion Options - Flue Gas Emission Control Options _ STAKEHOLDER VIEWS _ PROJECT STATUS _ EPCOR is an integrated utility company for water, gas, electricity and technology services. _ EPCOR has about 1.6 million customers in Alberta, Ontario, Manitoba, BC, and the U.S. Pacific Northwest. _ EPCOR Generation Inc. operates three power stations in Alberta which were in operation before deregulation, including the coal-fired Genesee Generating Station. _ EPCOR Power Development Corporation owns generating stations in Alberta, BC and Washington State and will be building the Genesee Phase 3 expansion.

May 1, 2002

By M J. Daniel

Mineral resources all over the world are often heterogeneous and have variable ore properties and ore grade. As a result the ore processed in concentrating plants varies over the life of mines. Consequently the circuits often suffer from bottlenecks typically at the stages of crushing, semi-autogeneous (SAG) and ball milling. Bottlenecks may be remedied with equipment retrofits, however, design engineers should consider a phased approach to the circuit design that delays initial capital expenditure over the life-of-mine. This paper deals with the debottlenecking of existing mineral processing plants by means of high pressure grinding roll (HPGR) applications. It also deals with the use of innovative flow sheet designs using HPGRs for the design of Greenfield plants by engineering or mining companies. In the case of Greenfield plant design an analysis with respect to energy efficiency and operating cost (OPEX) is presented. The analysis compares the performance of SAG based circuits against HPGR circuits that may be influenced by variable ore properties. Globally about 600 HPGRs are installed in various applications in the cement and minerals industries. In excess of 100 of these HPGRs are used since the mid 1980s for crushing and grinding of various ore types including æhard rockÆ applications. HPGR technology is mature enough to be considered as an ideal debottlenecking device. HPGRÆs are versatile, they have a low installation footprint and they are flexible in its machine settings (pressure, roll speed), which can be adjusted to react to ore variations whilst maintaining a high throughput. Examples for the benefits of using HPGR in terms of energy efficiency and operating costs are presented by this paper. æEco-efficientÆ flow sheets and sustainable development initiatives are linked to energy savings as an æenergy costÆ and benefit to the environment. Energy savingsÆ can also be analysed in terms of the ædollar costÆ (OPEX) savings. This paper demonstrates that HPGR is more energy efficient and may reduce the overall grinding energy requirements in the order of 16 per cent depending on the target grind size and ore properties. The HPGR is more cost efficient and may reduce overall grinding costs by as much as 19.3 per cent depending on the cost of energy, grinding media and the rate of grinding media wear in the comminution circuit.

Jan 1, 2009

By O. Leuangthong, M. Nowak

"The impact of high-grade data on resource estimation has been a longstanding topic of interest in the mining industry. Concerns related to possible over-estimation of resources in such cases have led many investigators to develop possible solutions to limit the influence of highgrade data. It is interesting to note that the risk associated with including high-grade data in estimation appears to be one of the most broadly appreciated concepts understood by the general public, and not only professionals in the resource modelling sector. Many consider grade capping or cutting as the primary approach to dealing with high-grade data; however, other methods and potentially better solutions have been proposed for different stages throughout the resource modelling workflow.This paper reviews the various methods that geomodellers have used to mitigate the impact of high-grade data on resource estimation. In particular, the methods are organized into three categories depending on the stage of the estimation workflow when they may be invoked: (1) domain determination; (2) grade capping; and (3) estimation methods and implementation. It will be emphasized in this paper that any treatment of high-grade data should not lead to undue lowering of the estimated grades, and that limiting the influence of high grades by grade capping should be considered as a last resort. A much better approach is related to domain design or invoking a proper estimation methodology. An example data-set from a gold deposit in Ontario, Canada is used to illustrate the impact of controlling high-grade data in each phase of a study. We note that the case study is by no means comprehensive; it is used to illustrate the place of each method and the manner in which it is possible to mitigate the impact of high-grade data at various stages in resource estimation."

Jan 1, 2015

By P. J. Sylvester, D. H. C. Wilton, R. I. Wheeler, M. A. E. Huminick, D. Evans-Lamswood

"Abstract — Systematic characterization of the mineralogy of massive sulfide ore deposits can provide valuable insights into ore genesis and metallurgical processing that would not be apparent otherwise. We describe a method wherein (1) normative mineral abundances are calculated from whole-rock chemical assays using an algorithm, (2) the results are cast in block models, (3) the results are then verified with automated image analysis of a subset of samples prepared as grain mounts by backscattered electron imaging and X-ray mapping on a scanning electron microscope, and (4) those verified results are integrated with textural data determined by optical microscopy.The technique is applied to the magmatic Ni-Cu-Co sulfides of the Ovoid orebody, based on geochemical assays of 3175 whole-rock samples. Three principal ore zones are defined in the Ovoid. Type I ore occurs in the center of the deposit; it is magnetite-rich and pyrrhotite-poor with intermediate contents of pentlandite and chalcopyrite. Type II ore surrounds Type I ore and is pentlanditechalcopyrite- rich with intermediate contents of pyrrhotite and magnetite. Type III ore occurs at the base and along the outer periphery of the northern part of the orebody; it is pyrrhotite-rich and chalcopyrite- poor with an intermediate content of pentlandite, and a low-to-intermediate content of magnetite."

Jan 1, 2012

By A. Kapito

The ferrite-pearlite microstructure is the most popular microstructure for alloys used in structural applications, including railway wagon wheels. These alloys have been designed through alloying and thermo-mechanical processing to have a refined microstructure. Ferrite-pearlite alloys are low cost, weldable, have good fabricability, and are reliable under extreme conditions. Given these performance attributes, it seems unlikely then that their dominant position as structural steels would ever be challenged by alternative microstructures. One major achievement in the development of ferrite-pearlite steels has been in the refinement of their interlamellar spacing to very fine distances of the order of < 0.3 um. A refined microstructure increases the hardness of the alloy, thus increasing its life under wear conditions. The interlamellar spacing in pearlitic steels has, however, been refined almost to its theoretical limit. The increasing demand for speed and increased axle loading on railway wagons requires the use of stronger, tougher, and more durable materials. This has opened the window for the development of novel bainitic steels. Bainitic alloys have a higher level of microstructural refinement than pearlitic ones. They have shown to have good wear resistance and rolling-contact fatigue resistance, and high toughness. This paper will discuss the progress to date on the development of bainitic railway wheel alloys. Four alloy chemistries have been chosen for possible further development.

Jan 1, 2012

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By F N. Baez

This paper supplements a keynote address prepared for the MassMin 2016 conference on mass underground mining methods, including block, panel, inclined and sublevel caving. It advocates for a new cave mining paradigm that takes advantage of a number of new and disruptive technologies or innovations that have evolved over the last 15 years, some of which were initiated by major mining companies such as Codelco. The paper will address the challenges that the industry will be facing in the future as well as possible solutions. As background, the paper summarises the challenges that the industry has faced in the past and how such challenges were addressed. The author acknowledges that given his more than 30 years of experience with Codelco Chile (operations and corporate), aspects of his intelligent mining concept have no doubt been influenced and have matured during his invaluable time with Codelco also as the Head of Technology and Innovation. In the paper, he uses some of the innovations developed within Codelco and by the Chilean Government to illustrate the concept of ‘intelligent mining’.CITATION:Baez, F N, 2016. ‘Intelligent mining’ – the way of the future, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 3–8 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The profitability of gold placer mining operations is determined by more factors than many placer miners recognise until too late. This study is based upon field trips to examine the efficiency of mining and transportation of gravels to a wash plant by bulldozer and truck. At the examined open pit mining operations gravels were washed using water canons, derockers or scrubber trommels. The objective of this study was to determine the relationship between unit costs and power requirements for gravel mining and processing. The author conducted a number of time and motion studies at four open pit gold mines, including the Maly Patom Creek, the Nizhny Patom, the Taimendra Creek and the Kadali-Makit in the Bodaibo District, Irkutsk Region and collected and processed field data. As a part of the study significant correlations were determined and empiric regression equations derived between: power requirements (Ep) and unit cost (Cp) for gravel processing; and total power requirements (Et) and total unit cost (Ct) for gravel mining, transportation and processing. Based on the results of the study it was proposed to modify the current mining procedure methods and to replace water cannons at the Maly Patom Creek with a PPM-5 derocker. Introduction of the proposed technology resulted in 2004 in US$385 000 mining cost reduction at the Maly Patom Creek over a short-time Siberian mining season.

Jan 1, 2007

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By James Withers, Dongbo An, Jinhong Zhang

A micro-scale investigation was carried out by applying atomic force microscopy (AFM) to study in situ the adsorption of various collectors, i.e., oleic acid, octanohydroxamic acid (HA), and salicylhydroxamic acid (SHA), on bastnaesite in aqueous solutions. The obtained AFM images show that the surface morphology of bastnaesite changes greatly after it comes into contact with the solutions of the collectors, suggesting that all these collectors can effectively adsorb onto bastnaesite. Increasing temperature can facilitate the adsorption of oleic acid onto bastnaesite. Results from attenuated total reflectance–Fourier transform infrared spectrometry (ATR-FTIR) also show that all of these collectors adsorb strongly onto bastnaesite, with strong absorbance spectra being detected. The ATR-FTIR results confirm those obtained by AFM. In general, hydroxamic acid collectors (HA and SHA) adsorb onto bastnaesite mainly in the form of insoluble metal hydroxamate. This specific adsorption mechanism explains that a high selectivity with a moderate collectivity will be achieved with a hydroxamic acid collector for the flotation of bastnaesite.

By C M. Wawryk, S L. Garwin, J D. Foden

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Batu Hijau porphyry Cu-Au deposit in south-western Sumbawa, Indonesia is an ideal natural laboratory to study the fractionation of iron isotopes in magmatic rocks that range in composition from basaltic andesite to tonalite. Intrusive rocks are associated with a porphyry system that contains well-preserved early hypogene copper mineralisation. We analysed pre-, syn- and post-mineralisation igneous intrusive rocks. We also separated magnetite, chalcopyrite and bornite from hypogene porphyry-style quartz veins, and measured the Fe-isotope ratios of samples by solution multi-collector ICP-MS. Iron isotopic composition of samples from the magmatic suite show an increasing d57Fe with increasing SiO2, supporting geochemical and textural evidence that the Batu Hijau Tonalites underwent closed system fractionation. Equilibrium and co-existing mineral textures allow the calculation of the following preliminary empirical mineral-mineral fractionation factors at 500°C for certain mineral pairs.Iron isotopes have the potential to provide geothermometric data to complement fluid inclusion data, especially where heating stages have operational limitations and where fluid boiling results in a wide variety of inclusion types that may make analysis difficult.CITATION:Wawryk, C M, Foden, J D and Garwin, S L, 2015. Iron isotope fractionation in magmatic-hydrothermal minerals – a porphyry copper case study from the Batu Hijau deposit, Sumbawa, Indonesia, in Proceedings PACRIM 2015 Congress, pp 389–396 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Tad S. Golosinski

The paper describes Online Master of Engineering Program at the University of Missouri-Rolla and discusses the experience gained during the first three years of its offering. This innovative educational program is designed primarily for mature students with an engineering or science background who want to acquire or upgrade their knowledge of mining engineering. Students can specialize in several different areas of mining, such as surface mining, underground mining, mine environment and the like. All courses constituting the program are taken online, through the Internet, without the need to attend the UMR campus in person.

May 1, 2004

By Nan Hua

As a high production and high efficient mining method, top coal caving method is now widely used in China. However, as more extra-thick coal seams are mined, it becomes more and more difficult to make the top coal fully broken up, resulting in more and more top coals flowing into the gob, rather than onto the rear AFC at the working face as designed. This research is aimed to investigate the failure mechanisms of the extra-thick top coal caving mining method.

Jan 1, 2009

By Dippenaar R, Evans T

Twin-roll continuous casting technology is rapidly approaching commercialisation. Fundamentally different than conventional continuous casting, heat transfer and hence solidification during twin-roll casting are governed by the interfacial melt/mould thermal resistance, as opposed to the resistance of the solidifying shell. Under these conditions the interface resistance is predominantly controlled by the melt/substrate wetting behaviour. The very early stages of melt/mould contact are characterised by highly transient heat transfer conditions. The overall melt cooling rates prior to the formation of the first solid are reported to be in the range of 1000 - 50000 K/s with melt undercoolings of up to 300 K. At the points of intimate melt/mould contact the thermal resistance is approaching zero, where cooling rates and undercooling much larger than those reported in the literature are probably occurring. Improved wetting will reduce the energy barrier for nucleation while at the same time increasing the cooling rate of the liquid. Since the overall nucleation rate is controlled both by the rate of cluster formation and the rate of atom transfer to the nucleus, a critical cooling rate will exist above which the nucleation rate is expected to be reduced. Under these conditions, it is possible that the first solid phase to form is a metastable glass which subsequently transforms into a crystalline phase. The implications on nucleation and early growth are also discussed.

Jan 1, 1999

During the drilling campaign conducted between October, 1942; and May, 1943, to prove the extent of the scheelite deposit worked by King Island Scheelite N.L. at Grassy, King Island, Tasmania, 35 holes were drilled and 606 samples recovered and assayed for their content. Of these, 238 came from outside the limits of the orebody and were for the most part barren, although a few contained some scheelite. The present statistical analysis is made only of the 368 samples taken from diamond-drill cores of the orebody itself.Drilling Pattern and Sampling MethodsFrom the purely statistical viewpoint, it is realised that methods employed in selecting sites for diamong.-drilling, and of collecting samples from drill cores, do not give a completely unbiassed set of data for analysis. Fig. 1 is a sketch plan showing the relativepositions of the drillholes, which were inclined at an angle of depression of 50 deg. The pattern does not conform to a properly randomized and&apos; regularly-spaced grid, the positions of the later holes being determined by the results obtained from previous holes.Statistically, the bias is, therefore, favourable. The unequal spacing of the drill holes and the lack of uniformity in direction of the lines along which the holes were drilled are unsatisfactory from the mathematical viewpoint; but it is realised that these irregularitiesare difficult to avoid in determining by the most economical methods the extent of such an orebody, and are dictated by geological rather than mathematical necessity.Sampling, also, is lacking in complete uniformity. Each sample is approximately 10ft. in length. However, owing to the fact that 100% recovery of core is rarely achieved, and actual lengths of samples taken are ,primarily governed by the length of the drill runs,and secondarily by lithological changes, there is a considerable amount of variation in the sample length.AssayingWith the exception of 28 samples from three drill holes all samples dealt with in this paper were assayed in the Melbourne University Ore-Dressing Laboratory of the Commonwealth Scientific and Industrial Research Organisation. These assays were given to the nearest 0.05% WOg as it was considered that more accurate determination was not possible. This fact has been taken into consideration in the frequency analysis below. The 28 assays determined by the Tasmanian Mines Department were given to the nearest 0.01%.

Jan 1, 1950

By Anthony J. Konya

"This paper was written during part of the author’s student co-op with Cargill Salt at its Avery Islandunderground salt mine in Louisiana. Blasting salt is a unique type of blasting that is different than blasting other rock types. The plastic nature of salt, along with its large swell factor make salt a challenge to blast. The Cargill salt mines use and have tested a variety of different methods for breaking salt in an efficient manner, however these blasting methods are rarely used in other operations nor talked about today."

Jan 1, 2016