Search Documents

By S. G. Malghan, J. P. Van Dillen

Introduction Some uranium minerals are paramagnetic and hence are amenable to concentration by high gradient magnetic separation (HGMS). This paper describes effects of the HGMS parameters-pulp velocity, field strength, matrix loading, and magnetic field gradient-on the product recovery and grade. Unsatisfactory separation of uranium minerals by HGMS is related to ore-specific properties, such as lack of liberation, fine dissemination of uranium minerals, uniform distribution of magnetic minerals throughout the ore matrix, and interference of fine-sized slimes. Experimental techniques to identify and resolve some of these problems are outlined. HGMS of Uranium Ores The mechanism by which uranium minerals are attracted to a magnetic field is either due to its magnetic susceptibility or its association with other minerals that are magnetic. Data on magnetic susceptibility of uranium minerals are scarce. The only reported data are for uraninite at 2360 X 10-6 cm3/mole. Povarennykh (Andres, 1976) concluded that the magnetic properties of minerals depend on: • Structure of the outer electron shell in a mineral with electropositive atoms; • Valence of the atoms; • State of the chemical bonds; • Type of coordination; and • Proportion of magnetic atoms (Fe, Mn, Cr, and Ni) in the composition of the mineral. However, information on the magnetic susceptibilities of the constituent atoms of a mineral alone does not suffice for evaluating the mineral compound as a whole. Most often, uranium minerals can be beneficiated by HGMS if they are associated with other minerals that are magnetic. This appears to be a more predominant mechanism by which the uranium minerals are beneficiated. Experimental A Sala-HGMS (Malghan and Subramanian, 1981), model 10-15-20, separator was used in the experiments. The matrix material-ferromagnetic stainless steel in the form of expanded metal or steel wool-was packed into a 38-mm (1.5-in.) diameter by 360-mm (14-in.) long canister. The matrix material occupied only a 150-mm (6-in.) length. The experimental set-up and slurry flow direction are described elsewhere (lannicelli, 1976). The response of uranium ores in the HGMS was studied by feeding well-dispersed slurry at 10% solids and examining the influence of process variables on selectivity and overall uranium recovery. The chemical and mineralogical characteristics of the ores under study are presented in Table 1.

Jan 12, 1983

By Gilberto Yanarico Apaza

"El presente texto señala las pautas necesarias para realizar una evaluación técnica integral de la influencia del collar de bolas para las operaciones de molienda, afectando al desgaste de los revestimientos de los molinos convencionales. Para la determinación del collar de bolas es necesario realizar los análisis granulométricos con la finalidad de obtener el F80 y el P80 de las muestras obtenidas en la alimentación y producto de los molinos, definir el índice de trabajo (Wi) y consumo de energía. Asimismo, se debe considerar el porcentaje de la velocidad crítica, las dimensiones de los molinos, la densidad de los medios de molienda (bolas), el porcentaje de la carga de bolas, las características geométricas de las bolas para molienda y el diámetro real de bolas, que influye de forma inversamente proporcional en la tasa específica del consumo observada."

Jul 1, 2015

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By Charlie Watts, Ken Smales, Ron Fleming

The Manapouri Power Station is an underground hydro-electric station located in the South Island of New Zealand, and was constructed in the 1960s. Between 1997and 2002, a second 10m diameter tailrace tunnel was constructed to increase the out-put and to improve the overall hydraulic efficiency and output of the station. A critical economic and project approval consideration for the second tunnel was the outage time required for the breakthrough into the power station. The power station is in part dedicated to providing power to an aluminum smelter with the balance to the National Grid, and apart from the physical problems associated with providing an alter-native power supply to the smelter, the loss of generation revenue and supply risk were significant issues. Innovative planning reduced the planned outage time from several months to21 days, and the breakthrough was eventually achieved in 11 days as a result of additional value engineering measures implemented during construction. This paper describes the engineering optimization that took place during the planning stages of the project and later during construction, as well as describing the construction methodology used.

Jan 1, 2007

By Mazin Adnan

The 80m high dam at the Peribonka river in the Canadian province of Quebec was designed for the generation of 385 MW of hydro electrical power (Fig.1). The complex ground conditions required the employment of a variety of geotechnical construction methods stretched to limits never experienced before. Innovative grouting and trenching techniques were used for the construction of a plastic concrete cut-off wall down to a depth of about 116m, to cut hydraulic seepage through alluvial deposits forming the dam foundation. The bedrock where the cut-off wall is embedded forms a glacial gully with steeply sloped flanks, which created further challenging conditions. [ ]

Jan 1, 2008

By D. A. Bruce

Small diameter cast-in-place bored piles (pinpiles) have been installed throughout the world since 1952, but only more recently in the United States. The special features of their construction and performance makes them ideally suited for structural underpinning applications in difficult ambient and geological conditions. This paper describes the underpinning of part of a major industrial facility near Mobile, Alabama. In addition to being a most interesting and successful case history, per se, the paper also describes in detail a fundamental test pile program which has afforded a unique insight into the basics of load transfer mechanisms.

Jan 1, 1992

By Seffen Leppla, Rolf Katzenbach, Matthias Seip

"Abstract The economic and safe design of deep foundation systems in difficult soil conditions is based on a reduction of construction material used, construction time spent, energy consumed and a high-level modelling of the soil-structure-interaction. The special foundation system Combined Pile- Raft Foundation (CPRF), in-situ load tests on the construction site and a sufficient soil investigation allow cost optimised constructions. In any case at challenging projects the observational method has to be applied for verification and quality control of the design. Regarding the 4-Eye-Principle as basis of the quality control management an independent peer review of the planning, design and construction phases is the guarantee for safety, serviceability and optimisation of all projects. Main execution standards for the construction of deep foundations based on the Eurocode 7 are summarised and discussed. The paper presents the basics of the safe and qualified design and construction of foundation systems including quality assurance. The application in engineering practice is shown on achallenging project of high-rise buildings with difficult boundary conditions.IntroductionThe construction of deep foundation elements in inner cities are special challenges due to the limited space for the construction works and the effects on existing buildings (Figure 1).An economic and safe design of deep foundation systems in difficult soil conditions is based on the following main aspects:•,qualified experts for planning, design and construction•,interaction between architects, structural engineers and geotechnical engineers•,adequate soil investigation•,design of deep foundation systems using the Finite-Element-Method (FEM) in combination with•,enhanced in-situ load tests for calibrating the soil parameters used in the numerical simulations•,quality assurance by an independent peer review process (4-eye-principle) combined with theobservational method if necessary"

Jan 1, 2014

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Esher Hsu

In Taiwan, around 8,000 tons of batteries are consumed per year but only 17% of which were collected and transported to oversea for recovery. The dumping used batteries have become a potential environment problem. How to increase the collection efficiency of used batteries is an important issue for EPA in Taiwan. Besides, some treatment plants are on process to get permission for recovering used batteries. The objective of this study is to estimate the recycling cost of spent consumer battery and explore the feasibility of recovering used consumer batteries in Taiwan based upon the principle of cost-efficiency. The recycling cost including collection cost and recovery is estimated based on a survey. Results would provide some suggestions to Taiwan EPA regarding feasibility of recovering used batteries in Taiwan.

Jan 1, 2006

By J. Bakken, M. Th. Jonsson, G. Sævarsdottir

A typical three-phase submerged-arc furnace for production of silicon metal and ferrosilicon has arc currents ~100 kA, phase voltages ~100 V and total furnace power ~10 - 60 MW. The arcs burn in gas filled cavities or "craters", where the main atomic components of the plasma mixture are silicon, oxygen and carbon. Two quite different simulation models for high-current AC arcs have been developed: the simple Channel Arc Model (CAM), and the more sophisticated Magneto-Fluid-Dynamic Model (MFD). These models have been described extensively and results reported at INFACON-8 and INFACON-9, respectively. The coupling between the arcs and the AC power source is described by a complete three-phase Electric Circuit Model. Recent numerical modelling studies of industrial AC arcs show that the boundary conditions at the cathode and anode are critical for the simulation results. A novel Cathode/Anode Sub-Model for high-current AC arcs that treats both cathode and anode indicates a completely different cathode behaviour than previously assumed. A cathode spot which serves a high-current electric arc is shown to be dominated by the energy impact from the arc. This leads to lower cathode fall voltage than obtained from previously developed models. The anode fall voltage is negative, as the main function of the potential barrier is to repel plasma electrons. The cathode spot is diffuse in the sense that the arc in fact contracts away from the cathode. Simulation results are compared to measurements on both industrial furnaces and smaller scale pilot furnaces. An important conclusion, supported by our arc studies, is that the arc length in silicon metal and ferrosilicon furnaces does not exceed 15 cm and the arc may burn anywhere on the electrode, not necessarily beneath the electrode tip.

Jan 1, 2004

By P. Somasundaran, D. R. Nagaraj, Tarun Bhambani, P. Patra

Flotation separation and recovery of value minerals from ores containing fibrous silicate minerals are known to be quite challenging. Earlier studies have established that the metallurgical challenges (poor selectivity and recovery, high energy consumption, etc.) arise from the impact of the fibrous minerals (with high aspect ratio) on pulp rheology, which was found be rather complex. The complex rheological behavior of ore suspensions containing particles with high aspect ratio and its influence on flotation outcome are investigated in this study. Flotation tests and rheological measurements were carried out with both ores (containing fibrous minerals) and a model system comprising nylon fibers (chemically inert) added to a copper ore that had no fibrous mineral. These studies allowed the determination of contributions of physical properties of the fiber to pulp rheological behavior. Optical microscopy images of the fiber pulp indicated that the fibers entangled to form two levels of microstructures: two-dimensional (2D) aggregates under semi-dilute (< 20% solids) conditions and three-dimensional (3D) microstructures at concentrations > 30% solids. The yield stress (σ) values determined for the fiber pulp were logarithmically related to the volume fraction of the 2D/3D structures. The relationships developed here for different ARs showed that the yield stress of a flotation pulp changes with respect to shape, size, and the concentrations of the microstructures. Implications to the effects of such entangle networks on selectivity of flotation separation are discussed.

Up to the end of World War n, flat-back cut and fill stoping with or without square sets was the universal method of ore extraction. Rapid changes in practice occurred during the post-war years; first, ore extraction was fully mechanized; secondly, the stope design for new levels, notably No. 17 Level Zinc Corporation Ltd. and No. 19 Level New Broken Hill Consolidated Ltd., was modified to suit this mechanization; and thirdly, sub-level and shrinkage stopes were developed in orebodies where cut and fill methods would be uneconomical. The following is a brief survey of the changes that have occurred-most of which were inaugurated during the last five years.ROCK DRILLINGDuring 1951 open stoping was investigated in detail. In order to reduce steel handling problems, forged steel onepass detachable bits were introduced, but were soon superseded by the &quot;Swedish method&quot;. Investigation showed that when using a bar and arm mounted 3-in. drifter the overall drilling time was approximately 6 min. per ft. compared with 4 min. per ft. using the light jackhammer-airleg combination with 1-in. hex. by 4-in. collared shank tungsten carbide-tipped steel.Although competitive with tipped steels on a cost per foot drilled basis (excluding miner&apos;s time), detachable steel bits proved most unsatisfactory for hard drilling conditions.Rapid blunting necessitated frequent bit changes and thus caused lost drilling time. This, together with rapid gauge...

Jan 1, 1957

By W. Sondermann

"AbstractThe construction of a distribution centre of minerals for a global mining and resources cooperation demanded the control of deformations and displacement of the stack reclaimer facilities on very inhomogeneous subsoil conditions. The variation of quality from soft clay with CPT values below 1 MPa up to rock formations were the challenge in design and execution of all the foundation works.The advanced design considerations were resulting in a barrier wall system to limit the deformations of the up to 40 m deep bored pile of the stacker-reclaimers, whereas the layout of the barrier wall and the stiffness of the elements had a major impact on the residual lateral forces to be absorbed by the bearing structure.IntroductionA large international raw material distribution organisation is currently building an iron ore and pellet distribution centre on the north-western coast of Malaysia. The distribution centre will handle around 90 MTPA (million tons per annum) of iron ore and includes accompanying plants for loading and unloading iron ore and pellets, pelletizing plants as well as corresponding storage space for these raw materials. The total storage space extends about 800m north to south respectively 1400m east to west and is about 200m from the coastline. The project area is located in a wide valley basin, bounded by a range of hills to the north. The existence of soil with low bearing capability in the area designated for the plant meant that measurements for ground improvement were required in the storage areas, in order to combine the needs of iron ore and pellet storage areas with requirements of the loading facilities as the overall project demand.Project LayoutThe iron ore distribution centre and the pelletizing facility both consist of an import/export jetty, material handling facilities, pellet plant and the associated infrastructure. This publication describes the execution of ground improvement and foundation works for the loading and storage system, which consists of five rows of stockpiles and four intermediate rows of stacker-reclaimers. The total area of these systems comprises 278,881 m2 (Fig. 1)."

Jan 1, 2014

By F. Stober, D. Wanblad, J. Ndlovu, L. R. Nelson, L. P. S. de Villiers

The single six-in-line furnace of the Polokwane Smelter is the largest installed high-intensity furnace for platinum group metals (PGM) base metals sulphide smelting in the world. The furnace employs state-of-the art technology to deliver a planned throughput of 650 000 t/a dry concentrate at a design 68 MW power input. This furnace, at double the capacity of previously existing PGM furnaces, offers low unit operating and capital cost through the resulting economies of scale. Key features of the design include:

Jan 1, 2005

By Hugh Thompson

In mining today, planning is of paramount importance, even more so when one considers that the business margins are reducing, requiring the evaluation of diverse alternatives for the optimal use of scarce resources. Additionally the capital required to approve some projects demands the best planning possible. Modern planning requires that all of the aspects of the business be represented, and not just the planning of the extraction in an isolated form. In order to carry out integrated strategic planning in the mining business one needs to have implemented a culture within the organisation that allows the business to be understood as a interelated system of processes. These processes must be co-ordinated so that they interact properly between each other and so define an integrated plan that optimises the available resources and maximises the benefit to the company. This defined culture should consider the important variables of each activity within the processes, and its’ relevance to the strategic plan. In this sense, this paper shows an example of computer tools used in order to reach the described objectives.

Aug 25, 2002

By Richard D. Begley

This paper summarizes the development of a mechanistic model to predict longwall mining induced surface subsidence. The model was originally developed from data acquired from a recent field study conducted in Northern West Virginia. Additional data has been collected from published sources and used to refine the model. The original model utilizes a negative exponential equation to predict the subsidence profile after the maximum possible subsidence is predicted based on the following input parameters: mine geometry, angle of draw and expansion factors for the deformation zones that have been identified above a longwall excavation. The model refinement involved the development of relationships between physical properties of the overburden strata and angle of draw in addition to the expansion or bulking factors. Therefore the refined model now requires only mine geometry and a typical geologic column from the site to predict the subsidence profile. This paper provides the methodology that enables the model to determine the angle of draw and expansion factors breed on physical properties of the site geology i. e. percent of strong rock and Rock Quality Designation of the overburden strata. In addition :comparisons of predicted results with measured data for over H) different sites with various geological and geometrical parameters located throughout the United States will be presented.

Jan 1, 1989

By Mikko Ruonala, Pertti Lamberg, Olli Hyvärinen

The smelting of copper sulphide concentrate is the dominant route in copper production (Figure 1). Heap leaching of oxidized copper ores with weak sulphuric acid together with copper solvent extraction and electrowinning has gained popularity during recent decades, and it accounts for close to 20 % of primary copper production. Heap leaching offers advantages such as lower costs and consequently the construction of a production plant at a mine site is made possible. Limited resources of oxidized copper ores, the long leaching time of chalcopyrite and inability to recover gold inhibit this growth. The HydroCopperTM process developed by Outokumpu Technology at the laboratories of Outokumpu Research, Pori, Finland, is a new chloride leaching technology /1,2/, which offers an alternative to smelting and heap leaching (Figure 1). In the HydroCopperTM process sulphidic concentrates with various mineralogy and grade can be treated at the mine site to produce high-quality copper. Instead of copper cathodes the HydroCopperTM end products are copper wire rod, copper bars or copper billets. One of the advantages of HydroCopperTM technology is that gold can also be recovered in the process simultaneously /3/. To confirm the functioning of the new process and to dimension equipment Outokumpu Technology built the HydroCopperTM demonstration plant in Pori, Finland /4/. It has a capacity of 1 metric ton of copper per day. After testing with Pyhäsalmi copper concentrate in 2003, the first commercial demonstration run with Erdenet copper concentrate took place in 2004.

Jan 1, 2005

IN dealing with this subject the intention is not to write a detailed description of the various methods in vogue on the Kalgoorlie field, but rather to give a brief outline of three of the methods which are most universally in force, and from which, ultimately, a few comparisons may be drawn. The three methods which the writer proposes embodying in this article are known as &quot;The Rill,&quot; &quot;The Flatback,&quot; and &quot;The Shrinkage.&quot; For comparative purposes each method will be applied to a block of ore 500 feet in length, and opened up by levels 200 feet apart.&quot;The Rin&quot; System. It is necessary in this system, for facilitating mullocking, to make connections between levels by rising and winzing at about every 100 feet or 150 feet along the orebody. After the leading stope is beaten off for the full length ofthe drive, the level is timbered. Single stulls are put in up to a width of fourteen feet. If the span is too great for stulls, set timbers or saddleback stuUs are used. Stulls are lagged over with 4-in gimlet poles, and wooden chutes are built at intervals of 50-feet. Ore passes are cribbed up through the filling directly above each chute, and are constructed of 7-in. round timber or 9 in x 3 in square timber, the passes measuring 4 ft x 4 ft in the clear.Occasionally a double pass may be carried up, one side serving as a travelling way. Stoping is commenced off the winzes, and rills are gradually formed, one on either end of each winze. The rills are generally at an angle of 37&#176; off the horizontal, this allowing for the boring...

Jan 1, 1909

By Rob Sloan, Simon Yu, Rob Robison, Mark Schmidt

"In 2000-2009, Highland Valley Copper (HVC) tested new generation 660 mm cyclones supplied by various manufacturers in an aim to replace existing first generation 762 mm cyclones without success. Due to plant infrastructure limitations, new generation larger (838 and 800 mm) cyclones were not feasible. In 2010, an approach of testing hybrid 800 mm diameter cyclones was initiated by HVC. The hybrid cyclone consists of an 800 mm cyclone upper head section and the use of existing 762 mm cyclone conical sections. Three hybrid 800 mm cyclones were engineered and fabricated, targeting a throughput of 850-950 mtph and were installed in the E line cyclone cluster. Since starting operation on September 20, 2011, three hybrid 800 mm cyclones have been running at combined throughput ranges of 750 to 1050 mtph. Based on plant Daily Met Reports, the test hybrid cyclones demonstrated a decrease in misplacement of coarse copper bearing material to the cyclone overflow and better cyclone efficiency when compared to the existing 762 mm cyclones at the same throughput. The hybrid 800 mm cyclones also demonstrated significantly higher capacity per unit when compared to the existing cyclones. Based on the improvement demonstrated in the full plant trials, HVC decided to install the new hybrid 800 mm cyclones in all five grinding lines starting in July, 2012. A more detailed discussion of the full plant trials and initial results of the first complete retrofit of E line will be presented. INTRODUCTIONHighland Valley Copper Partnership (HVC) is Canada’s largest base metals mine and one of the world’s largest producers of Cu-in-concentrate. The mine, located in the central interior of British Columbia, is owned (97.5% interest) and operated by Teck Resources Ltd. In 2011, HVC produced about 210 million lbs. of Cu and 8 million lbs. of Mo. HVC’s Mill Modernization Project (MOP), which was budgeted for $475 M, is currently under intensive construction and is scheduled for commissioning in Q1 2014. The following description was valid at the time of writing this paper.The operation has been expanded a number of times since the startup of the original Lornex mill in 1972. The plant started up with two 9.75 m (32 foot) diameter primary SAG mills. It was expanded in 1981 with the addition of a 10.36 m (34 foot) diameter SAG mill. In 1988, the Highmont concentrator grinding mills and flotation section were moved and attached to the Lornex mill site. This added two10.36 m (34 foot) diameter AG primary mills to the Highland mill. This brought the total number of primary mills to five referred to as Line A, B, C, D and E: three SAG mills (A, B and C) each with two ball mills in parallel and two AG mills (D and E) each with one ball mill. Each AG mill line is equipped with one short head pebble crusher. Ball mill circuits are classified using 8 clusters of ten Linatex 762 mm cyclones to reach a target P80 330 micron (equivalent 43% +100 mesh), before the cyclone overflow product advances to the bulk flotation circuit."

Jan 1, 2013

By Peter K. Kaiser

Planning and design of deep underground mines involves a process of complex three-dimensional data integration utilizing information from exploration (geology, rock mass characteristics), engineering (mining method, excavation geometry, stress) and operations (time, in the form of sequencing). As new logging and monitoring technologies are being developed, the amount and data complexity becomes overwhelming and decisions are often made based on only a small part of the available data. Recently, Laurentian University opened a state-of-the-art Virtual Reality Laboratory (VRL), a Mining Exploratorium that is unique in the world of mining and offers an exceptional data interpretation environment for mine planning and design. The Mining Exploratorium combines a large format spherical stereoscopic projection system, equipped with high definition projection providing the highest resolution of active stereo in the world today, with advanced features of earth modeling software. Combined, this creates the first virtual reality facility geared specifically to the interpretation of mine geometry, geology, geochemistry, microseismicity, geomechanics and mining data sets. This paper demonstrates how value can be added to the mine planning and design process by utilizing this unique tool in the mining decision-making process via better comprehension of spatial relationships of data and by interpreting the data in a collaborative immersive virtual reality environment.

May 1, 2002