Search Documents

By J. D. Miller, C. L. Lin

Appropriate software and hardware necessary to adapt a x-ray CT analyzer for determination of coal washability has recently been developed and sucessfully tested for well characterized samples under laboratory conditions. Evaluation of the CT-based analyzer under simulated on-line conditions is also presented to verify the on-line capabilities of the newly developed x-ray CT analyzer for the control of coarse coal cleaning circuits. The investigation shows that the data obtained from CT washability analyses compare favorably with experimental sink-float data. Further, image frequency was considered to evaluate the CT-Based coal washability analyzer for simulated on-line conditions. Specifically the number of observations (image spacing) needed for accurate sampling and the total time required to perform the calculations for a representative data set were determined.

Jan 1, 2001

By Peter Yen

This session consists of five papers. Three involved research on the properties of grout materials, specifically ultrafine cements and polyurethane grouts. Two papers present the development of soil grouting technology and monitoring methods. Of great interest are the papers on ultrafine grout penetrability testing focusing on the pressure filtration effects encountered in permeation grouting applications (Ericksson, Stille and Mittag, Savidis). The comparison testing of hydrophilic and hydrophobic polyurethane grouts submitted by Vrignaud, Ballivy, Perret and Fernagu assessed the long-term performance of these materials for repairing saturated cracks in concrete, subject to thermal expansion and contraction. Two very practical papers present the development of soil grouting, where permeation, fracture, replacement, jetting and other grouting techniques are utilized. The papers by Lees with Chuaqui and Warner present experience with ultrafine and other commonly used grout materials. Methods to measure and monitor the injection process and verify production progress are discussed.

Feb 10, 2003

By S. J. Schatzel

Longwall coal mine operators in the US are required to ventilate multi-panel longwall districts but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs), and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. Consequently, the performance of coal mine bleeders is an important aspect of underground worker safety. U.S. coal mining stakeholders have acknowledged their belief that the T- junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. The percentage of air directed inby towards the bleeders and bleeder fan and outby to the submains is often not well-defined and can vary over the life of a longwall panel. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the intake air stream along the panline of active longwall panels and in the bleeder/gob ventilation air inlets of an inactive panel. Tracer gas sampling was conducted underground using tube bundles attached to permissible vacuum pumps in the gateroads, former gateroads, and bleeders. Surface tracer gas monitoring was also conducted from operating gob boreholes and from bleeder fans. Testing was performed on multiple longwall panels which included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. The applied methodology defines and describes coal bed gas pathways, rates, and volumes of movement at the bleeder/gob interfaces, and indicates flow rates for air/gas mixtures within these gobs. These findings are reported for three stages of longwall extraction using direct field-based measurements. Changes in the T-junction ventilation air distribution over the life of a longwall panel and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements and to achieve the desired ventilation patterns through multiple phases of longwall panel extraction.

Jan 1, 2011

By G. H. Bennett

A field experiment was performed in a production unit of an operating copper room and pillar mine to compare the support capabilities provided by resin and mechanical roof bolts. Resin and mechanical roof bolts were alternately installed in eight intersections in a single entry. Rock mechanics instrumentation was installed to measure roof sag, bed separation, convergence, bolt pullout, torque, and strain. Bolt cost and installation time are included. Two analyses of the test were made. The analysis of the rock mechanics data showed there was no definite difference between the two bolting systems. From a broader analysis on a mine-wide basis it was concluded that resin bolts gave better support. A critical view of the experiment is given in the appendix.

Jan 1, 1974

By Michael Young, Peter Allum, Mingwei Gao

"Tough economical conditions and high grade but fine-grained ore processing have forced the mining industry to look for more efficient processes. Isa Mill Technology for ultra-fine and fine grinding is one such process employed at several mining operations in Australia including Mount Isa Mines Limited in Australia. Mount Isa Mines is a business unit of MIM Holdings Limited. MIM is an Australian-based international mining and mineral processing company with around 8000 employees worldwide. Major products include copper, gold, zinc-lead-silver, coal and technology sales.The Isa Mill is a horizontal stirred mill with sizes up to 3 m3 chamber net volume and 1 120 kW installed motor. It was jointly invented by Mount Isa Mines of Australia and Netzsch Feinmahltecknik GmbH of Germany for ultra-fine and fine grinding duties in the minerals industry. Isa Mill operations started in 1994 at the Mount Isa Mines Leadzinc Concentrator and then at MIM’s McArthur River Mine in 1995. These Isa Mills have been used to liberate sphalerite and galena at Mount Isa and silica at McArthur River by grinding to less than 7 micron.This paper discusses the Isa Mill Technology and reports on the metallurgical performance of the Isa Mills at Mount Isa Mines, including work done over the last 9 years to improve mill design, process efficiency and maintenance, which has resulted in the current state-of-the-art Isa Mill Technology.INTRODUCTIONThe current leadzinc deposits at Mount Isa Mines (George Fisher, Hilton and Isa) have an average grade of 10.5% zinc, 7.2% lead and 165g/t silver. Fine grinding, in particular in the zinc retreatment circuit requiring a milled product P80 of 7 micron, is essential to treat the ores from the Mount Isa Mines deposits. Every one micron size reduction in the zinc retreatment circuit below a P80 of 10 micron improves the overall plant zinc recovery by 1%, resulting in an increase in revenue of about 1 million dollars per annum."

Jan 1, 2002

By Verya Nasri, Heather M. Ivory, Kevin Clarke, Eric Cole

Development of the New York City Water Supply System The New York City water supply system serves a population of almost nine million, including residents in neighboring counties. Peak day demands on the system are currently running at about 70 m3/sec (about 1,600 mgd), which is significantly lower than in the 1990s. This trend of reducing demands over the past 25 years, which has been experienced in other major urban centers in the US, is mainly the result of conservation measures and increased cost consciousness on the part of water users. In the long term, demands are expected to once again follow an increasing trend with population growth, so that by the end of the planning horizon of these studies, the year2045, the peak day demand is expected to increase to about 85 m3/sec (2,000 mgd).The system is served largely by surface water sources, regulated by a system of 19reservoirs and three controlled lakes, which are connected to the City by a series of aqueducts, the longest of which is about 87 km (54 miles). The total storage in the sys-tem amounts to about 560 billion gallons, providing a system firm yield of about1300 mgd. The Delaware system provides about 50% of the City’s water, the Catskill about 40%, with the remaining 10% provided by the Croton. The system as a whole, which is shown on Figure 1, has been built up over the past 150 years, and is truly a marvel of engineering. The Catskill and Delaware aqueducts both discharge into Kensico Reservoir, which is a daily balancing reservoir located in Westchester County about 24 km(15 miles) north of the New York City line. The two aqueducts extend south for a further 14 miles to combine again at Hillview Reservoir in the Bronx, which provides hourly balancing storage for New York City system. The Croton aqueduct runs nearby as shown on Figure 2, but does not connect into the two reservoirs. From Hillview Reservoir the water is supplied to the city via three main distribution tunnels, known as City Tunnels 1, 2, and 3. City Tunnel No.1 was developed in the 1920s as part of the Catskill system. City Tunnel No. 2 followed in the 1960s as part of the Delaware system. City Tunnel No. 3 (CT3) is partly under construction and partly in operation, and is being implemented to permit the other distribution tunnels to be taken out of operation for the first time for inspection and maintenance. Presently CT3 is supplied with water from Hillview Reservoir via a large underground valve chamber, the Van

Jan 1, 2007

By Clayton V. Deutsch

Indicator Kriging (IK) is being commonly applied to mineral resource assessment problems. More recently, indicator simulation has also been used for sensitivity analysis and difficult change of support problems. The essential theory underlying indicator geostatistics has not changed since its introduction 10 years ago; however, the last decade has produced many important developments in its implementation. The objective of this paper is to consider some of the more important implementation details. Examples from the Porgera gold deposit in Papua New Guinea are used to illustrate the steps in an indicator geostatistical study and the importance of various implementation decisions. Specifically, in many precious metals deposits the continuity of the grades is typically quite anisotropic. This anisotropy varies in both magnitude and direction throughout the deposit. Building a model of this anisotropy can considerably improve the local kriged or simulated points. One approach to build this model is presented. In addition, there is typically more than one mineralization style and geological rock type; the spatial character of the mineralization can be quite different within each geological rock type. The rational treatment of anisotropy and geological subdivisions is common to all mineral resource assessment procedures; the importance of this qualitative geological information is not diminished with more sophisticated techniques such as indicator kriging. This paper presents an overdue comprehensive look at the practical aspects of indicator methodology. Many of the techniques and procedures documented in this paper have been developed during the course of detailed mine feasibility studies.

Jan 1, 1992

By Lutz Markworth, Wolfram Jaspers, Johannes Kottmann

PNEUFLOT® technology has been applied for the past 20 years in coal, ore and other minerals processing plants. During the last two years this technology has achieved a breakthrough with some 42 units being sold signifying a rising trend. »Humboldt Wedag Coal & Minerals Technology« has performed extensive research and development work over the last five years. The results of which were used to design a new fourth generation aerator. Humboldt Wedag, through its association with EKOF, can offer a holistic solution encompassing both flotation equipment and reagents. It is the only company in the world able to offer such a package. The association with EKOF strengthens the Humboldt Wedag product offering, especially as the company in-troduced pneumatic flotation cells to the South African market in the form of the PNEUFLOT®. Before starting pilot scale test work, a mineralogical analysis has to be carried out to determine the mineral com-position as well as the liberation grade. HW-CMT works together with independent institutes. Different reagent regimes can be tested in laboratory scale. Pilot machines, each packed in a 20? container, are available to carry out extensive test work at customers? processing plants. A group of engineers from HW-CMT is involved in the pilot test work. The flexible pilot machines are designed to cater for coal, ores and other minerals. The small feed rates of 7 ? 12 m³/h only means the pilot machines do not disturb the operation of process plants. Batch tests have to be carried out to determine the numbers of PNEU-FLOT® stages. New applications in iron ore, copper ore, platinum group minerals, rock phosphate and potash were suc-cessfully tested in the last three years. In applications where the feed material is very fine, PNEUFLOT® technology is able to achieve high recoveries with particle sizes where conventional technology failed.

Jan 1, 2007

By Hiroshi Soda, Atsumi Ohno, Hiroyuki Yamazaki, Alexander McLean

INTRODUCTION The method of heat removal during a casting process strongly influences the crystal morphology of the cast product and hence the metallurgical and mechanical properties of the solidified materials. In this paper, the Ohno Continuous Casting Process (OCC) is described in terms of the casting conditions and the type of structure observed in the cast product. Significant improvements are observed in workability, fatigue strength and corrosion resistance of castings produced by the OCC method, Ohno (1988). Applications of this technique to low melting point nonferrous metals and alloys are discussed. The feasibility of the application of this technology to high melting point materials is outlined. THE OCC PROCESS The OCC process involves delivering liquid metal into a heated mold, the temperature of which is held just above the solidification temperature of the metal to be cast. This is the key point which differentiates the OCC process from the conventional continuous casting method. A schematic illustration of the OCC process is shown in Figure 1. The Formation of a Single Crystal When the mold is heated above the solidification temperature of the metal to be cast, nucleation on the mold surface is prevented and solidification takes place only at the mold exit. The heat is extracted through the product being cast by a cooling device located near the mold outlet. Crystals are formed only at the tip of the dummy bar at the start of casting, and as the dummy bar travels away with a progressively increasing speed from the mold, the position of the solid liquid interface will align with the mold exit, producing a unidirectionally

Jan 1, 1990

By Xiao Caimei

The method of Substance Flow Analysis (SFA) provides a helpful tool for the study of the industrial metabolism of a certain metal within a regional level, such as copper, lead etc. In this paper the flows and inventory of cobalt in China, 2008, were traced with the STAF model, and the situations of production, fabrication and manufacturing, use and waste management in China were introduced. The result revealed that the resource of cobalt in China was so poor that a large amount of cobalt material or cobalt products needed to be imported, and there was lack of recycling of cobalt resources.0

Jan 1, 2010

Multiple regression analysis was used to predict elemental concentrations of copper and nickel in soils from consideration of the concentration of these elements in vegetation in an ultrabasic complex in New Zealand. Regression equations were computed from sixteen independent variables involving concentrations of ten elements in plant ash, and various physical factors such as slope and altitude of the site, and height of the tree. One elemental and one physical variable were significant for nickel at the 90 per cent level of probability and five elemental and two physical variables were significant for copper at the same level. Use of the regression equations explained 32·5 per cent and 26·5 per cent of the variance in the respective relative accumulations (amount in plant divided by amount in soil) of copper and nickel.Predicted concentrations of copper and nickel in soils agreed more closely with the observed values in the soils than did the levels of these elements in plant ash.Although the results may specifically apply only to the test area, the principles should have universal application.

Jan 1, 1972

By G. Song

"SynopsisAccording to the overlying rock strength and thickness of 10 shallow coal seams in China, the strata are classified into four types: weak and laminated strata (hereinafter referred to as WL), weak and massive strata (WM), strong and laminated strata (SL), and strong and massive strata (SM). The four types of strata, together with longwall panel height (M), panel length (L), and seam depth (H) are factors that influence the loads on hydraulic power supports. Principal component analysis was used to study the seven influencing factors. It turns out that seam depth (H) is multicollinear with WL, WM, SL, and SM. Thus the enumerated seven factors are divided into two models. In Model 1, six factors; panel height, panel length, and layer thickness of the four type strata are involved. In Model 2, three factors; panel height, panel length, and seam depth are included. Using multivariate regression analysis, two equations to calculate loads on supports are obtained for each model. The equations were applied to shallow coal seams. The equation of Model 1 is more accurate than that of Model 2, but Model 2 could be further used in deep coal seams. The equations were coded through VB programming to simplify the calculation.IntroductionTo ensure coal production in the long term, the focus of coal mining has been gradually shifted to the western areas of China in recent years due to rich coal resources in this region. Most of the coal seams in this area are shallow but the support loads are abnormally high. In these circumstances, the chock loads estimating methods used in the past do not work. If the rated working resistance of a support is larger than needed, the shield is unable to fully perform, while a lower working resistance would lead to accidents like shield crushing or even casualties. This problem is frequently found in shallow coal seams such as Shenfu-Dongsheng, Yulin, Tuha, Lingwu etc. (Zhang, 2011). Thus, to ensure safety and efficiency during mining, the estimation of support loads and selection of supports are of great significance."

Jan 1, 2015

By Ana E. Bohé, Georgina De Micco, Juan P. Gaviría, FEDERICO J. POMIRO, Gastón G. Fouga

Chlorination and carbochlorination processes have industrial applications in metallurgical activity for extraction and purification of uncommon metals such as rare earth elements (REE). This study reviews the chlorination and carbochlorination reactions of light REE (LREE) oxides with chlorine considering the thermodynamic, stoichiometric, and kinetic aspects of the reactions. Lanthanides between lanthanum to gadolinium were considered as LREE, in agreement with previous literature, and the results were detailed in this review. LREE were analyzed taking into account their oxidation states and were divided into three groups accordingly. The results presented show that, although the LREE are chemically similar, their behaviors during the reactions with Cl2 and Cl2–C, and the different LREE-O–Cl compounds formed, have particularities. It was observed that gadolinium, in both thermodynamic calculations and experimental results, presents some differences, and it can be considered intermediate between light and heavy REE; i.e., reactions between LREE2O3 and Cl2(g) begin at approximately 250 °C, except for Gd2O3 that begins at 327 °C. The present work will contribute to a better understanding of the chemistry of LREE oxides and Cl2 under different conditions and the products obtained in the LREE–O––Cl2(g) and LREE–O–C–Cl2(g) systems.

Oct 15, 2021

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

Incident investigation is of utmost importance in most high-risk industries and is often used to improve organisational safety. This study was undertaken to examine the content of past incident investigation reports to determine the effectiveness of the incident investigations. The study uses a semi-quantitative method to assess the effectiveness of incident investigations in the Ghanaian mining industry by evaluating the quality of past investigation reports. The assessment tool consists of five elements with several indicators and rating scales for assessing the quality of an investigation report as a measure of the effectiveness of the investigation. The method was applied to 304 investigation reports of three Ghanaian large-scale gold mines, and the results correlated with incidence rates of the mines to determine if any relationship existed. The results showed that the mines differ significantly in the quality of their investigation reports, suggesting differences in the effectiveness of their investigations. In addition, the incidence rates of the mines negatively correlated with some elements of the assessment tool. In general, the method was found useful and revealed areas where improvement is needed.

By Preston C. Holloway

Transformational roasting involves the heating of a material along with specific additives to induce mineralogical changes in the starting material. By controlling the chemical composition, roasting atmosphere, temperature and time of reaction, the mineral transformations induced during roasting can be engineered to control the distribution of valuable, or harmful, metals and to produce new mineral assemblages that are more amenable to conventional methods of metals recovery or to environmentally safe disposal. To date, this type of process has only been applied to the recovery of a limited number of metals, but current research is looking to expand the application of these techniques to the recovery of metals from a wider range of materials. An introduction to these techniques is presented along with preliminary results from their application to metals recovery from zinc bearing wastes, such as zinc ferrite leach residues and carbon steel electric arc furnace dust.

Jan 1, 2006

By Juliana Colacioppo

La voladura es un procedimiento que está diseñado para obtener pilas a través de una fragmentación adecuada para el carguío y transporte, aumentando así la productividad de las palas y camiones y asegurando la estabilidad de los taludes y condiciones del piso de los bancos en la mina. Asimismo, el diseño de la voladura debe optimizar las operaciones posteriores tales como chancado, zarandas, clasificación, molienda, flotación y lixiviación. En ese sentido, el presente texto describe la metodología de optimización de procesos de la miina Antamina hasta la oncentradora a través de la recolección de datos de campo, caracterización, modelación matemática y simulación de las operaciones, donde además se utilizan sistemas de rastreamento de minerales y de análisis continuo de imágenes.

Sep 9, 2007

By Warren E. Morrison

Stimulated by 4 years of continuous economic growth without inflation, demand for energy in the United States reached an alltime high in 1964. Total value of production of goods and services (gross national product--GNP) for the year was $629 billion, an increase of 6.8 percent from 1963. Allowing for price changes based on 1958 dollars, the gain in real terms was 5 percent. In 1964 the Federal Reserve Board Index of Industrial Production stood at 132, a rise of 6.2 percent. With the impetus provided by personal income and corporate tax reductions during the year, aggregate wages, profits, and consumption reached record levels. Even the persistent balance of payments problem improved. Against this background the national consumption of commercial energy increased 4.2 percent. Energy needs continued to be met largely from domestic resources with imports, mainly crude petroleum and refined petroleum products, accounting for but 7 percent of the total. Mineral energy resources, namely gas, coal, and petroleum, contributed 96 percent of the input of energy into the economy during the year. The remaining 4 percent came from hydropower and nuclear power.

Jan 1, 1965

By Jay A. Berger

Nondestructive testing of deep foundations for integrity problems made great strides in the late 1980's. Inexpensive portable computers have allowed the immediate and rapid processing of field measured acceleration records which can provide insight into the relative structural integrity of a previously installed foundation member. Although the gathering, processing and displaying of the data is now straightforward, interpretation remains at times rather challenging. This paper provides a brief introduction into the theoretical basis for data interpretation and the hardware necessary for data acquisition. Five case studies are discussed which demonstrate the varied applications of low strain integrity testing of deep foundations and the efficiency at which they are completed. BACKGROUND One dimensional wave mechanics, when applied to a linear elastic pile with a length that is an order of magnitude greater than its width, provides a straightforward basis for the interpretation of motion measurements made at a pile top. When impacted, a stress wave travels through the pile at a wave speed, c, which is a function of the elastic modulus, E, and mass density p (i.e., E=pc2). The applied load F, and particle velocity v, at a point are related by the equation F=Zv. For a cross-sectional area A, the proportionality constant Z is equal to EA/c. Because Z is a measure of the pile's resistance to change in velocity it is called the pile impedance.

Jan 1, 1990

By E. C. Robertson

D.G. Wilder I found the suggestion that the amount of displacement of a fault can be numerically related to the thickness of gouge or breccia to be both intuitively satisfying and intriguing. I have long agreed that there is some type of relationship between the amount of gouge and the amount of displacement of faults. I congratulate the author for developing a numerical relationship between them. However, I am concerned that the limits for applying this relationship be fully understood. An underlying assumption in this approach is that there is either a uniform thickness of gouge or breccia along a given fault or the thickness does not vary widely. Since it is not always possible to confirm this, the displacements derived by this method should be viewed with caution unless significant fault extent can be observed. At the Nevada Test Site, in drifts constructed in granite for test emplacement of spent nuclear reactor fuel, we found a fault with 0.3 to 0.4 m (12 to 16 in.) of clay gouge. Within a few meters of this location, the fault had no clay gouge, but rather consisted of a highly fractured zone with significantly altered rock and some slickensides. Based on Fig. 1, the 0.3 to 0.4 m (12 to 16 in.) thickness of gouge would indicate a displacement in excess of 30 m (98 ft). However, no gouge thickness would indicate essentially no displacement. Based on a quartz vein that terminated on the fault, and is not identified nearby, an estimated displacement of more than a few meters was made. This estimate is consistent with that obtained using the regression line proposed in the paper if the 0.3 to 0.4 m (12 to 16 in.) thickness for the gouge is used. However, using the regression curves with zero thickness would not yield results consistent with what was observed in the field. Therefore, it is important to recognize that the suggested procedure would properly yield a range of probable displacements. ? *Work performed under the auspices of the US Department of Energy by the Lawrence Livermore National Laboratory under Contract W-7405-Eng-48. Reply by E.C. Robertson It is certainly true that the t (thickness) of gg-bx (gouge and breccia) on a fault does vary along the fault. My observations have been that near the termination of a fault, the displacement d is small and the t is also small, whereas the maximum d and t will usually be found in the central part of the fault. The information on gg-bx and t of the fault found in granite in the NTS tunnel by Mr. Wilder could be interpreted somewhat differently than he does. He speaks of the fault changing within a few meters from 0.3 to 0.4 m (12 to 16 in.) of clay gg to "a highly fractured zone with significantly altered rock and some slickensides," but no gg. The highly fractured rock may be taken to be bx, rock not so finely ground as gg but still crushed by the fault movement, equivalent to the gg in my usage, and probably occupying about the same t. Mr. Wilder's estimates for the fault in the NTS tunnel for t of 0.3 to 0.4 m (12 to 16 in.) and for d of a quartz vein, in excess of "a few meters," would place the point on the low side of the central trend line in my Fig. 1, at the lower limit. There is, of course, a problem with determining d using displacement of only one planar surface. It would be greater or lesser depending on the rake of the movement. Finally, estimating the d of a fault from its t should be made with awareness of our present uncertainties, as pointed out by Mr. Wilder. Although the central trend line in my Fig. 1 has a ratio of d/t of 100, I have put the limiting ratios at 10 and 1000. Understanding of the values of the ratio will be improved only with collection of more data, for which the discussion of Mr. Wilder is much appreciated. G.C. Waterman E.C. Robertson's paper provides significant information to a geologist attempting to deduce fault offset by noting the products of structural dislocation. However, considerable mapping in underground and open-pit mines, and examination of structures produced in different geological settings, have convinced me that gouge and breccia thickness are controlled by geological conditions and fault movement. The following paragraphs suggest geological variables that control them. 1. Depth of Loading A near-surface fault resulting from tensional stress has more breccia/gouge than is produced by a similar stress at considerable depth. A deep-loaded compressional stress may produce a linear zone of schist, or structural dislocation may occur along an earlier formed belt of schist. Such "shear zones" are common in Canadian mines in precambrian rocks. In neither case can offset be directly deduced by an analysis of the minimal gouge/breccia in the shistose rocks. At greater depth, stress may be partially to wholly relieved by flowage. I vividly recall first noting the regional "Midas Thrust" in the Lark mine, Bingham Mining District, UT (where we called the structure the North Fault). My recorded notes, as I remember them, showed a narrow gouge streak separated the `Jordan" and "Commercial" limestone units from impure, muddy limestone beds of uncertain stratigraphic position. The visible structure did not indicate the great importance of this premineral fault

Jan 12, 1984