Search Documents

By Mark E. Smith

Oxide ores can consume enormous amounts of expensive sulfuric acid. The problem is amplified with increasing heap heights. One solution is to provide a thin liner and drainage system between each lift of ore, thereby intercepting the pregnant leach leach solution (PLS) after it exits the active lift. However, these liner systems require special attention to hydraulics, slope stability and geomembrane design criteria. Inadequate attention to the first two can result in reduced recoveries, increased acid consumption andsystem failures. The geomembrane selection criteria are different from the base liner, and optimizing its selection can have significant effects on the operation’s bottom line.

Jan 1, 1996

By Nikhil Dhawan, Ashwini Kumar, Yogendra Pratap, Himanshu Tanvar

India does not possess any soluble potash reserves and depends completely on imports. In this study, an attempt has been made to recover potash (K) values from the mica sample employing thermal and mechanical routes followed by leaching. Direct leaching of mica in different lixiviants is found to be ineffective with very low K-dissolution (1–5%). Heat treatment with different fluxes, such as NaCl, NaOH, and CaCl2, is carried out and almost 85% K-values are recovered. Mechanical activation of mica and with different calcium additives is carried out to recover potash values. K is recovered in leach solution in the form of soluble salts, such as K2CO3, K2SO4, and KOH, and leach residue consists mainly of calcium-alumino-silicates. Using mechanical activation with flux, it is possible to recover >95% K-values from mica sample. Mechanical activation with calcium-based flux is found sustainable in the recovery of K-values from mica.

By Chris Breeds, Larry Leone, Jerry Wallace

Project Owners typically require General and Detailed Blast Plans when blasting close to important structures and specify the maximum allowable peak particle velocity for each potentially affected structure. Low, residential level PPV limits may be specified which significantly restricts the potential for blasting to be effectively used. Contractor’s responding to these contract conditions typically cite historic case studies which may, or may not, apply to the specific situation and/or types of structures for which limits have been set. A long submittal cycle typically follows.

Jan 1, 2010

By Donald J. Murphy

Longevity of structural units, as compared to the planned useful life of a facility, always is a design consideration. Typical concerns include slow decay due to environmental factors, and changes in constitutive relationships governing the performance of the material involved. With respect to foundations, the usual items of interest are corrosion of steel and concrete, and time dependent behavior of the soil/structure system. For piles, as with other foundations, deterioration is precluded, mitigated or otherwise accounted for by assessing properly the ambient situation (sulphates, pH, stray currents, resistivity) and providing safeguards, such as resistant construction products, oversizing, coatings, and/or cathodic protection. On the other hand, long term performance of the pile foundations, as affected by time dependent characteristics of the supporting soil or rock, can be predicted and controlled only with a synergetic coupling of analyses and field tests. The history of a project for which this approach was followed forms the basis for this paper.

Jan 1, 1986

By Tariq B. Hamid

Deep excavation is commonly associated with construction of different deep below-grade structural elements (e.g., basement walls and slabs, tunnels, retaining walls, tanks, utilities, etc.) Deep Excavation Retaining Systems (DERS) are required when open cuts with safe slopes are not possible. Careful analysis, design, and planning of the DERS are required to provide safe below-grade construction and secure nearby structures from damaging effects that may result from the deep excavation. Selection and design of temporary or permanent DERS (e.g., soldier pile and lagging, sheet piling walls, secant pile walls, tie backs, etc.) can have significant impact on time, cost, and performance. In order to design DERS using conventional methods, it is necessary to obtain shear strength parameters, angle of internal friction (ø), and cohesion (c), of retained soils. Residual shear strength parameters (ø'res, c'res) obtained from drained direct shear tests and triaxial tests on saturated samples have been commonly used in practice for the analysis and design of DERS. However, there are cases where ground water table remains at or below the base of excavation during the design lifetime of DERS. In such cases, the soil above the ground water table is in an unsaturated state. Therefore, it is important to account for the unsaturated conditions of soils in order to optimize the design of DERS. This paper is focused on implementing the basic concepts of unsaturated soils mechanics including matric suction and soils-water characteristic curve (SWCC) to estimate design shear strength parameters of unsaturated soils (i.e., ø°, c', and ø') for the design of a cantilever sheet pile walls, a typical case of study of the DERS. The results of this study indicate that the determination of unsaturated soil strength shear strength parameters is simple. In addition, using unsaturated soil mechanics theories has an outstanding impact on the design of retaining systems.

Jan 1, 2006

By Alain Bouchard, Germain Labonté, Jim Barrett

"Mill feed materials that are not run-of-mine ore are often a challenge for mineral processors and tend to accumulate in stockpiles, where they remain unprocessed for many years and become “slow moving inventories”. During a complete re-evaluation of the Clarabelle Mill operation (38,000 ton/day capacity) in 2000, it was concluded that there was an opportunity to assemble a 5,000 ton/day custom circuit to treat such stockpiles in the equipment that remained available during regularly scheduled maintenance shut-downs.This project was part of the larger Mill Redesign Project and involved testing the intended flowsheet under a number of operating scenarios for the first material to be treated: spent refractory bricks. The laboratory focus was on how to maximize returns using the available equipment and reagents.The circuit was successfully commissioned in the fall of 2000. As the brick stockpile was depleted, other potential feeds were evaluated at the laboratory, as well as in the new custom circuit itself. Processing of the spent refractory brick has yielded a significant contribution to the profitability of INCO. Significant opportunities lie ahead for generating more value from other slow moving inventories.INTRODUCTIONIntegrated mining operations tend to have slow moving inventories along the path from the mines to the finished products. Spent refractory bricks from furnaces and converters and furnace bottoms are materials that often end up in long-tern stockpiles. Such stockpiles are a challenge, although they represent small tonnages on an annual basis, because they are unique materials, which cannot be readily brought into the process at a rate anywhere near that at which they are produced, due to the high contents of deleterious components such as chromite or magnesia. Accumulation over years will eventually yield a metal inventory worthy of consideration given the right opportunity, such as availability of spare equipment or peak metal prices."

Jan 1, 2002

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By Roberto Maldonado

El presente texto señala el proyecto de profundización en la mina Animón considerando sus características como: geología e hidrogeología, parámetros geomecánicos, niveles de producción, costos de capital y operación, eficiencia del sistema, flexibilidad para cambios en las operaciones, reservas de mineral y consistencia con el sistema de explotación. De forma que a través del conocimiento de estas y de las herramientas gráficas tridimensionales, se pueda analizar las diferentes alternativas, incluyendo condiciones que debe cumplir el proyecto de profundización, el cual abarca también los servicios auxiliares y ventilación.

Sep 12, 2005

By R. A. Williams

The Pascua Lama Project is situated on the border of Chile and Argentina at an elevation of 4,800 m. The ore contains gold, silver and copper, and an initial milling production rate of 33,000 t/d is planned. The mineralogy of this deposit is unusual. The ore is hard and abrasive, and it contains a complex array of sulphate minerals, such as chalcanthite, jarosites and alunites. The sulphides are predominantly enargite and pyrite. A novel flowsheet has therefore been developed, which includes dry grinding and ore washing to remove and then neutralize the soluble salts, prior to flotation, cyanide leaching and Merrill-Crowe recovery of the precious metals. These metallurgical issues and challenges associated with plant design and construction in the high and remote Andes Mountains make this a particularly challenging project.

Jan 1, 2001

By Roy McKinstry, Mark Rantapaa, Thomas Bolles

"More efficient drilling and blasting techniques have shown measurable improvements in throughput at the Barrick Goldstrike wet grinding mill.A decrease in throughput at the autoclave, due to increasingly hard ore, was identified in early 2002. A team of individuals from the Open Pit and Process areas participated closely on the Drill-to-Mill (D2M) Continuous Improvement initiative to ensure that it would address the needs of both groups, with the target of improving throughput in future years, despite the projected harder ores. Plant studies were conducted to determine if adjustments to drilling and blasting could positively influence throughput. At the Goldstrike mill the greatest opportunity from the D2M initiative is realized on the hardest ore. Grinding throughput for softer ore, <15 kWh/st, can meet or exceed the downstream pressure oxidation requirements. Grinding throughput for harder ore, >15 kWh/st, is limited by the SAG milling capacity. Better fragmentation in the D2M ore, as demonstrated by image analysis, increased throughput 5% to 10% (25 to 50 stph) compared to the standard mining methods.Better fragmentation and a subsequent increase in mill throughput were achieved through the use of:1) Electronic caps for more precision and flexibility, as well as for allowing extremely fast shots.2) Explosives with a higher velocity of detonation (VOD), to provide for improved shock energy.3) Improved distribution of the explosives by decreasing pattern spacing.INTRODUCTIONThe Barrick Goldstrike Open-Pit group, along with the Process division, began experimenting with novel blasting technology and techniques to improve mill throughput in the spring of 2001. A series of tests were developed to determine if fragmentation and ultimately mill throughput could be influenced by optimizing the drilling and blasting program in known"

Jan 1, 2004

[This Report represents the culmination of work perfomed under Contract No. .,JG1551A8 for the U.S. Bureau of Mine.The &apos;.:o-< embeded a site evaluation, engineering E:-y- ,, esign, and preparation of specifications for construction of a Transport Research 7 :4 (HTRF)The HTRF is designed as a research facility J evaluate the hydraulic transport of large lump coal at a prototype ;e scale. The HTRF is to be constructed and operated by the Pittsburgh and Safety Research Center of ;. re U.-AN a*, their Bruceton, Pennsylvania test center. In terms of technical capability, the HTRF will have transport pipeline:: of -, twelve-, and eighteen-inch diameter _&apos; with supporting coal handling n , water forage a.^ &apos;d conveyance, mixing, pumping, and dewatering equipment, plus instrumentation and controls. Maximum design velocity 13 20 ft/sec.; solids concentration, by, volume, will; 1 be a maximum-- of sixty, percent. Each test loop is designed to accommodate solids of up to one-third the diameter e - of the pine. The Final Report Pr.-&apos;I-rents information of t HTHF,. including the site evaluation, design criteria, a description of the a description of the procedure to be used for operation of the facility, an estimate of the cost to construct the f^Cilit:r, 1 p el_~lli.&apos;iU construe`, icn Schedule, and a construction suicJ_iicaT.l_ccn&apos;. T e c011SLr?Jc&apos;.ion soecl_ i.on _ccnta_i:s technic.&apos;..i re7,uir: (-n`,s for !&apos;urr1S~ &apos;~latcr..al. and ec-uipr,ent for :":C1 C_`:_C ti on of ti,_ H ice&apos; u:&apos;.:i ._II u s(-.6 for ~.Iir: .3!7 soliciting bids. `.l_o included n cc&apos;;,art_- c?r~.air sV:et..: :s ^nd rr^.?]

Jan 1, 1976

By M. Beus, S. Inverson, B. Stewart

Abstract Recent ore pass failures have underlined the need for improved designs, standards, structural mon¬itoring methods and better hang-up prevention and removal tech¬niques. Researchers at the Spokane Research Laboratory of the Na¬tional Institute for Occupational Safety and Health (NIOSH) are investigating methods to improve safety during the transport of ore in ore passes. Design criteria and hang-up prevention and remedia¬tion strategies involve studies of the effects of static and dynamic ore and waste-rock loads on chutes, walls, gates and support structures. Particle flow analysis methods were used to simulate the response of various ore pass designs to a wide range of ore loading condi¬tions. A full-scale mockup of ac¬tual ore pass and chute assemblies was duplicated and tested for load response. Data from a particle flow code and the mock-ups were com¬pared Loads on an active ore pass chute were measured.

By James McNally, Adam Stremcha, John MacGregor

With 13.7km of TBM tunneling in Atlanta’s hard gneiss well under way, drill and shoot work continues on several sites throughout the city. In order for the City of Atlanta to meet the consent decree imposed by the federal government, an aggressive construction schedule was a necessity. Construction consists of two deep, large diameter tunnels, four construction shafts, a pumping station, one overflow shaft, three large intake structures, and two connecting tunnels. Due to the multitude of blasting insensitive urban environments, a high standard of seismic and air-overpressure criteria, coupled with time restrictions, was adopted for the project. At any given time, drill and blast operations were under way at four of the seven sites requiring a certain amount of coordination between the TBM excavation, surface work, and the forces of Mother Nature. This paper addresses the challenges faced and the techniques used to safely and successfully complete the rock excavation of the West Area CSO Tunnel and Pumping Station project.

Jan 1, 2007

By Maral Papazian Bedian

Construction contracts in the USA contain the clause "Value Engineering" ? an interesting and curious clause allowing contractor initiated design changes. Misleading is the interpretation of value engineering implying cost saving and sharing with the owner, and curious is the timing, just before beginning of actual construction. It is not surprising that such a clause would simply be ignored, because it involves change, often major design changes in very short time; and change is feared, moreover, it is vehemently resisted by all parties, owner, designer, contractor. The problem in the USA may lie in the divergence and separation of the two entities: Designer/Engineer and Builder/Contractor, assigned to the "one" engineering project. The priorities and incentives of these two groups are very different. The Engineer spends years, even decades, in design and prepares contract drawings often without a deep understanding of construction methods. Worse, with all the time available to him and in our era of tremendous advances in computational methods and speed, the designer turns in plans that are inexcusably exaggerated code-based design with excessive safety factors. As to the Contractor, he builds, often without appreciation of design principles or regard for design engineers. Redesign to apply a new technology or optimization of an inferior design just before construction becomes unthinkable. It is not surprising that adverse and hostile relationship between the designer and the contractor is a norm with extended disputes and claims, not to mention the cost these entail. Surprisingly, "Value Engineering" was successfully implemented in record speed on several very large projects in the metropolitan New York area. The process of change was unconventional, painful, and even comical. Four case studies are presented: two Design/Build: the 1.2 billion dollars Hudson-Bergen Light Rail Transit System in New Jersey and the 90 million dollars MTA Bus Depot in Manhattan, and two Conventional Design/Bid/Build: the 90 million dollars Queens Boulevard Bridge and the 150 million dollars Long Island Expressway.

Jan 1, 2002

China has made great progress in thick coal seam mining, commonly characterized by longwall top-coal caving mining and single-pass longwall mining with a large cutting height. At present, the maximum mining thickness of longwall top-coal caving reaches 20 m while that of single-pass longwall mining approaches 8.8 m. The top-coal caving–related technologies have significantly improved the mining efficiency of thick coal seams and have also made a great contribution to the centralized underground mining of coal. Thus, the number of underground coal mines is greatly reduced in China. However, due to the increase of the mining height and the changes in mining operations, the overburden movement caused by the mining of thick coal seams is more intense, and the influence scope is larger, which brings a series of new problems on ground control of longwall faces. In order to enhance ground control and improve the mining efficiency of thick coal seams

Jul 28, 2020

"Rock falls involving a relatively small amount of material are a leading cause ofinjuries in underground mines in the United States. A contributing factor is unwantedblast damage and over-break. A goal of the United States National Institute forOccupational Safety and Health is to reduce the number of ground fall-related accidents by improving drift driving practices through the introduction of perimeter control blast designs. This paper presents a blast design technique based on a hydrodynamic method. Using commonly available explosive and geometry data, the theoretical particle velocity is calculated as a function of distance away from a cylindrical charge. A calibration factor is introduced to account for actual conditions by comparing the predicted values to a set of field data. The calibrated curve can then be applied for design. The paper introduces modifications to account for different explosives from those used in a calibration test. The application of the approach is demonstrated with respect to a data set from a large-scale concrete block test."

Jan 1, 2009

By Peter (Yunqing) Zhang

Longwall recovery under weak roof conditions could have considerable delay if the immediate roof is weak and deteriorates during screening. A pre-driven longwall recovery room is a feasible solution to minimize the impact of longwall move on production. In this longwall recovery project, a 16-ft recovery room was pre-driven to cover screening, and the shearer cut another 16 ft outby to reach the final recovery line. The pre-driven recovery room was carefully monitored as the face was approaching it. The longwall face operated very well as it cut into the recovery room. The recovery process took about 13 days, and considerable time was saved compared with the previous panel. The support in pre-driven recovery room was designed to handle both front abutment pressure and weak immediate roof conditions. Pumpable standing support was used to support the cantilevered roof as the fender pillar narrowed and collapsed when the face cut into the recovery room. To ensure the stability of the recovery room, 3-D computer modeling was used to evaluate the support system. Abutment pressure, critical fender pillar width, bolting system, pumpable cribs and shield support were considered in the model. The recovery room was carefully monitored during longwall recovery. Roof-to-floor convergence and crib convergence were recorded every shift as the longwall face was approaching the recovery room. Roof, floor and pillar activities and crib performance were also observed as the face cut into the recovery room. This paper presents the support design for the recovery room, evaluation of the support system through computer modeling, and details of the monitoring results.

Jan 1, 2006

The first principle one usually Learns about blasting is that cunpetence in this field is best gained by experience in making blasts rather than by reading a book or by listening to a lecture. The reason for this is that there are a large number of variables affecting blasting results and not all of these can be accounted for by a few rules or a few sets of equations. Even an experienced blaster when operating in a new area, may have to make one or two shots just to acclimate himself to the new conditions with which he is faced.

Jan 1, 1989

The principal dirnensions of the chimney were fixed as follows: Height from formation to coping, 328 ft. 8 in.; inside diameter concrete shell, 13 ft. Gin.; inside diameter of the 4~-in. brick lining. 11 ft. (j in. ; shell thickness above flue inlet at a point 39 ft. above formation, 1 ft. 8in.; shell thickness at coping, 6 in. That is, the inside of chimney is cylindrical, wldst the outside is gradually stepped inwards with of 1 in. and less until the shell is 6 in. thick only at the top. With these dimensions in mind, it will be seen that some close thought was necessary to ensure a satisfactory of fonn which could be kept rigid and plumb to a height and at the same time provide safe working conditions for the labourers employed.FOUNDATIONSThe spread base of the chimney is 45 ft. in diameter, and foundations were carried down to a depth of 8 ft. 6 in. below natural surface into good hard clay which was known to be the best foundation obtainable in the vicinity being capable of withstanding, when dry, a load of 3 tons to 4 tons per square foot, whereas dead load is 1A tons per square foot and the maximum load expeeted under the most severe wind condition is 2 tons per square foot to ensure the foundation being kept dry and unaffected by ground water, the site was surrounded by a ring drain at a distance of six feet from edge of concrete foundation and at a minimum depth of one foot below bottom of concrete. Open-jointed pipes were laid in the bottom ofthe drain and graded to a pipe drain with outfall clear of the site.

Jan 1, 1924

Using a series-model of an automotive short range radar sensor (SRR) and a recently completed experimental radar system, field tests have been performed in a surface mine. It was examined, to what extent low-cost electronically scanning radar sensors can provide useful data for assistance systems on large scale mining machines. Simple sensors are useful for anti-collision safety zones or hopper car automation. The more complex and sophisticated experimental radar system using digital beam-forming can clearly detect and map the contours of trenches and slopes. The overall promising results refer to many more potential applications for electronically scanning radar in surface and underground mining as a reliable alternative to mechanical laser scanners.

Jan 1, 2007