Search Documents

By C. M. Haberfield

"1 INTRODUCTION Around the world, there is a demand for larger structures, tall buildings and large bridges. While good footing design is important for all structures, it is even more important in the case of large structures. Recent experience with footing design for tall buildings (e.g. Burj Al Alam development and Nakheel Tower in Dubai, the Gate of Kuwait in Kuwait, the City Centre Project in Bahrain and Eureka Tower and Freshwater Place in Melbourne) has shown the benefits of investing in footing planning, design and construction (Haberfield, 2011, Poulos and Bunce, 2007). The footing systems for most of these projects include the use of deep bored piles or barrettes (piles of rectangular cross-section). Many use piled rafts where the piles, while acting to support the load, are primarily used to reduce settlements. A clear understanding of the factors controlling the behaviour of the footing system is needed to enable a good engineering design to be achieved. This starts with a sound understanding of the ground characteristics and individual pile performance, including adequate collection of data and testing. The best footing solution can then be found using recent improvements in data collection and analytical techniques, complex and highly capable computer-based models and the availability of high speed computers. This paper focuses on the axial performance of deep bored piles socketed into rock – both their individual performance and their performance as part of a larger footing system. Recent research and construction practice is discussed. In practically all cases, serviceability conditions control the behaviour of the footings. Methods of establishing the parameters for input into sophisticated computer programs are described. Application of the methods to case studies is included and it is shown that the behaviour of individual piles can be closely predicted. These developments lead to lower construction costs, better constructability and shortened construction time because of the better understanding of footing behaviour. 2 FACTORS AFFECTING PERFORMANCE OF FOOTINGS ON ROCK For a typical pile-supported footing, it is necessary to consider both individual pile, pile group and raft performance. These require consideration of the behaviour of the ground immediately beneath the surface raft or footing, along the pile shaft, and at and beneath the pile toe (Figure 1). Immediately beneath the surface raft or footing, the important factors are strength for bearing capacity and stiffness for settlement and interaction effects. Along the pile shaft, of most interest are strength for bearing, excavatability and stability; stiffness for settlement and interaction effects; geology and permeability for pile stability and, most importantly, pile shaft resistance. At the pile toe all the above factors for the pile shaft are present and in addition the pile end bearing is of interest. Below the toe, stiffness for pile settlement is important to at least a depth of twice the building width."

Jan 1, 1900

By D. Bradbury

Sufco coal mine, a subsidiary of Arch Western Bituminous Group, recently purchased a reverse osmosis (RO) system. The systems intent was to remove impurities in the water being mixed with the hydraulic oil to maintain the viability of critical longwall hydraulic systems and to prevent degradation. This project not only ensured hydraulic components from corrosion, but also revealed a cost savings by reducing the percentage of hydraulic oil mixed with the RO water. SUFCO WATER TREATMENT HISTORY Sufco coal mine has been in operation for approximately 70 years. Old works extend up to 15 miles one way, not including adjacent mined out longwall panels. Due to the geologic conditions and strata, water treatment has been as simple as putting water in at a high point of a mined out area and recovering it at a low point to discharge. Doing this reduces the total suspended solids (TSS) to less than 25 parts per million (ppm) and the total dissolved solids (TDS) less than 1,200 ppm which complies with Sufco?s water discharge permit. Even though the requirements for the permit were met, the water is still corrosive in nature. A portion of this water is piped back into the fireline (makeup) water system. It is then boosted to pressures of up to 500 psi to support mining sections, belt systems, equipment, fire fighting systems and the longwall.

Jan 1, 2011

By John A. Wells, Leticia Conca, Kenneth G. Thomas

"Since about 2002 there has been significant capital cost escalation, not inflation, in the mining industry causing turmoil for successful project completion. Project capital costs have more than doubled and some cases tripled in this time period. This has rendered many projects to be economically challenged and in some cases not viable. In addition higher than expected operating costs have further adversely affected project metrics such as NPV and IRR. Capital cost increases for projects have been widely reported globally. This current paper reviews three items. Firstly, why such capital increases and the various components that make up capital estimates. Secondly, it looks at reasons why preliminary estimates, for example at scoping and pre-feasibility level, have been lower than the ultimate constructed costs. Such increases and differences in estimates have caused major problems for mine builders and have led to a general nervousness on the part of those providing project finance. Thirdly, what discipline is needed in project execution in an attempt to mitigate such capital increases. The paper will hopefully give a better understanding of the various issues and factors involved for those in the mining industry.INTRODUCTION The years 2012 and 2013 were a turbulent time for the mining industry. The European economic crisis, politics, metal price volatility and a wave of changes of CEO´s in some of the major mining companies all contributed to a challenging couple of years. Two issues stood out. First, the huge increases reported in the capital costs of projects, where increases of 100% - 300% were not uncommon and in some cases exceeded that during the first decade of the 21st century. Second, company write downs related to takeovers during the boom and the stabilization/correction in commodity prices. These have led to great uncertainty, made it difficult (or impossible) to raise project financing costs, contributed to the changes at CEO level and placed many projects either on hold or cancelled altogether. It is commonplace now to read of companies talking of reduced capital expenditure and making a complete review of their projects and operations to contain costs."

Jan 1, 2014

By Jason Rrno

The emergence of Impact and Benefit Agreements (IBAs) in the Canadian mining sector has been read by many as a positive governance innovation. Negotiated directly between mineral resource developers and Aboriginal communities with limited government interference, IBAs serve to manage impacts associated with a mining project and deliver tangible benefits to local communities. Notwithstanding their increasing use and significance, limited systematic analysis has been undertaken to determine whether they are, in fact, working. This paper reports on the effectiveness of a number of IBAs negotiated in support of three northern Canadian diamond mines, drawing on evidence from time-series data, key informant interviews, and focus group meetings in Yellowknife and Dettah, NWT, and Kugluktuk, NU. While some deficiencies were apparent and perceptions of effectiveness varied somewhat by Aboriginal community, the IBAs were generally found to be meeting their objectives, especially with respect to the delivery of benefits. For Aboriginal communities affected by mineral development in the Canadian North, this represents a significant change to typical outcomes of the past. Moving forward, research on IBA effectiveness needs to adopt a longer timeframe and begin to gauge the degree to which IBAs are able to address long-standing concerns associated with hinterland resource extraction beyond their agreement-specific objectives.

May 1, 2010

By J. B. Gilliatt

The discovery of ore at Wabana was quickly followed by the mining of the ore beds where they outcropped in the land areas. The third phase, as at present carried out, consists of extensive submarine operations, which were commenced in 1908, by driving a pair of slopes out under Conception bay, opening. the mine for a distance of a mile and a half from the shore. Two other slopes, now driven just beyond the shore line, are being sunk to the submarine territory where, it is generally recognized, huge reserves of ore lie under the bay. The process of erosion of the land, the solution and re-disposition of its iron-bearing minerals in thick beds of ore have been considered elsewhere, but these bear small relation to the physical forces which have acted upon the ore-beds since the deposition of the strata. These physical changes are made manifest by jointing and cleavage and faulting. The discussion of these, the relation they bear to each other, and to the folding of the strata, is the purpose of this article. For the benefit of those who may not be familiar with the formation in which the ore occurs, I include a general summary of the geology of Be!! island and its environs; also a description of conditions that prevailed during the period of deposition, so that the reader may appreciate some of the later changes that took place during or subsequent to its emergence from the sea, and the folding or tilting of the strata to the position it now occupies.

Jan 1, 1924

By Mary Stewart, Jim G. Petrie, Geoff Brent

"Life Cycle Assessment (LCA) is gaining increasing acceptance as a decision-support tool by which to evaluate the environmental performance of a product, process or service. This is evidenced by its inclusion in international policy documents (for example in the European Union’s Integrated Product Policy) and in environmental management standards (the ISO 14 040 series of environmental management codes relate to LCA). In response to this, the minerals industry has conducted a number of commodity-specific LCAs. These include studies for global production of a number of commodities including copper, nickel, aluminium and steel. In addition, a number of minerals companies profess to use LCA as part of their suite of project and technology assessment tools. Often, this collected use represents more a situation of “we do this because we’re told it’s good for business” rather than from any demonstrable evidence of this fact. This has led to a situation of much confusion and disillusionment within the industry, exacerbated by the obvious current limitations of LCA to accurately reflect the environmental performance of minerals and metals.Our point of departure here is that LCA, conforming as it does to the tenets of environmental systems analysis, is a valuable starting point, and that there is merit in exploring to what extent the methodology can be enhanced to better reflect the environmental performance of minerals and metals. Specifically, we explore here the further development of LCA to address the following:• Land Use issues• Consumption of Abiotic Resources including metallic and non-metallic minerals, water and soil)• Human and Eco-toxicity issues relating to mobility and bio-availability of metals• Salinityand address these through selected experimental and simulation case studies relating to energy- and base minerals production. Advances resulting from the United Nations Environment Programme/Society for Environmental Toxicology and Chemistry Life Cycle Initiative are presented in that they directly affect the application of LCA to mining, minerals and metals. Comments are offered on how best the mining and minerals industry might interface with future developments resulting from this Initiative in order that the Initiative can deliver outcomes which render LCA a useful tool for decision making in mining and minerals processing."

Jan 1, 2003

By Lily Ruíz

El presente texto evalúa el relave minero de SIMSA con el objetivo de obtener un producto ecológico que pueda ser utilizado como mejorador cationico de suelos y restaure el equilibrio de los suelos ácidos de la selva peruana. Para ello, se desarrolló un trabajo a nivel de laboratorio, obteniéndose resultados satisfactorios. Posteriormente se pasó al nivel piloto donde a través de la experimentación se utilizó el relave en diferentes concentraciones para la producción agrícola y forestal, reafirmando los resultados en las mejoras de la productividad en suelos ácidos.

Sep 9, 2007

By J. van der Merwe, D. Tharandt

The corrosion behaviour of 304L stainless steel laser-cladded with various amounts of ruthenium (Ru) was evaluated in solutions of sulphuric acid and sulphuric acid plus sodium chloride at 25°C and 45°C by open-circuit potential and cyclic potentiodynamic polarization tests. In general, the addition of Ru to the stainless steel increased its corrosion resistance in 1 M H2SO4, as well as in 1 M H2SO4 plus 1 wt% NaCl. This was observed for a number of parameters such as corrosion rate, corrosion potential, open-circuit potential, and current density. However, increasing the amount of Ru added beyond a certain level did not result in further improvement in corrosion protection. For each environment there is an optimal Ru concentration for the best corrosion protection. For example, in 1 M H2SO4 at 25°C, 2.44 wt% Ru shows the least active surface in terms of corrosion. Further research into ruthenium coatings on stainless steels is recommended.

Jan 1, 2015

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

By S. S. Cole, C. E. Wood, T. L. Joseph

"INTRODUCTION Iron ore containing titanium was first used in blast furnaces over a century ago. It is well known that TiO2 is a slag-forming material that will increase the amount of slag produced by the usual gangue materials, silica and alumina. Increase in the volume of slag due to the presence of TiO2 and a lack of information concerning its effect on the properties of the slag have prevented the general use of titaniferous ore. Also rather com¬mon belief among furnace operators that the bottom of the furnace builds up when ores containing TiO2 are smelted has militated against the use of titaniferous ore. This building up of the hearth has been attributed to the formation of copper-colored crystals of titanium cyanonitride, which have been observed in the salamanders of blast furnaces. Until recently the availability of nontitaniferous iron ore has left little incentive to use ore containing titanium.The presence of vanadium in certain deposits of titaniferous magnetite in New York State has created new interest in problems connected with the use of titanium-bearing ore. It appears that most of the vanadium in this ore can be recovered in pig iron, which can be blown in a converter to produce a slag containing vanadium in amounts suitable for the production of ferrovanadium.The Titanium Division of the National Lead Co. recently erected a largo mill to treat ore from Sanford Hill, in Essex County, New York, about 50 miles west of Port Henry. The ore deposit was acquired from the MacIntyre Iron Co. and is often referred to as Sanford ore. It is one of the largest deposits of Iron-bearing material to be found east of the Lake Superior region and is being mined by open-pit methods."

Jan 1, 1943

In a previous paper the writer dealt -with the jasper bar formations and their relationship to the structural geology of older pre-Cambrian rocks in the goldfields districts of Western Australia (24). He has pointed out in this ahd other papers that jasper bars, or banded iron formations, banded hematite or ,magnetite quartzites, jaspilites and related banded ferruginous or non-ferruginous cherts, occur in abundan'ce in the Older Greenstone Series of Western Australia (22), (24), (26). They are considered to represent special forms of banded ferruginous sediments, and are usually fpund in the field interbedded with more or less metamorphosed pasaltic 01' andesitic lavas and tuffs, now amphibolites, together with occasional thin bands of normal pelitic sediments, which go to make up a large proportion of the Older Greenstones in thfs State (26).Great thicknesses of fiat-bedded ]:landed ferruginous cherts are also found associated with cherty' carbonate rocks; quartzites, shales and thin-bedded dolomite whicIi constit'ute the Nullagine (Pl'oterozoic) system in the northwest of Western Australia. In the Hamersley Range district these banded ferruginous chert beds are the hosts of important deposits of blue amphibole asbestos.In the paper mentioned above brief reference was> made to the importance, of geological structure in relation to economic geology, particularly in the goldfields regions of Western Australia, and it was shown that jasper bars may have an important role in the study of 'the structural geology of many of these regions. Of possibly more immediate economic importance is the part that these rocks play, both directly and indirectly, as host rocks for mineral deposits-the chief of Which are gold, iron ores, blue asbestos, and manganese ores. The blue asbestos bearing banded iron formations mentioned above are confined to the younger pre-Cambrian Nullagine formations. They have been described in detail elsewhere (23). In this paper it is proposed to discuss the economic geology of the jasper bars found in the older pre-Cambrian series.The jasper 'bars have in themselves little or no intrinsic value except perhaps some of the more highly coloured and banded varieties which may be utilised for ornamental and decorative purposes. Probably the best known of such varieties is the so-called "marble bar;" a belt of, strikingly coloured banded chert occurring just south and west of the famous town of that name (see Fig. 1t). This consists of a hard, very fine, even-grained rock with alternate individual stripes varying from the thickness of a sheet of paper up to an inch or more in width, and ranging in colour from clear white to yellow, from various shades of pink to brilliant...

Jan 1, 1943

By Tassos Grammatikopoulos, Gary Pearse, Massoud Aghamirian, Charlotte Forstner, Stephen Mackie

"SGS Minerals Services (Lakefield, Ontario site) has conducted a number of developmental and pilot programs that examined methods for the beneficiation, extraction and recovery of lithium from a variety of spodumene containing hard rock sources. An overview of the beneficiation programs is presented separately by Aghamirian, Mohns, Grammatikopoulos, Imeson & Pearse (2011). The focus of this discussion will be the hydrometallurgical steps involved in producing a high grade lithium carbonate (Li2CO3) sample from the spodumene concentrate. SGS has applied the standard Li2CO3 hydrometallurgical flow sheet to a number of spodumene concentrates and has determined that all of these samples respond in a similar manner to the process and produce a final product having a Li2CO3 grade of >99.5%. The standard process is sufficiently robust to accommodate the observed variability in the concentrates that have been tested. Advantage of one spodumene deposit over another will thus be gained through process optimization and innovation. Optimization at the beneficiation stage and at the hydrometallurgical stage must be considered. Some aspects of the process optimization of the hydrometallurgical flow sheet will be presented.INTRODUCTION The current activity in the exploration, development, and mining of lithium based minerals is due in large part to the key role that this metal plays in the rechargeable battery industry (U.S. Geological Survey, 2011). Lithium battery technologies are widely applied in a range of portable electronic consumer products. The expanding development and production of hybrid and fully electric vehicles has contributed to the increased interest in finding and developing new lithium sources in order to meet the expected demand from the lithium battery industry. Lithium may be sourced from continental brines (sub-surface salars), hard rock minerals (pegmatite, spodumene), hectorite clay deposits, geothermal brines and oilfield brines. Currently the majority of the lithium products are produced from Li brines. The four major lithium producing countries are Chile, Australia, China, and Argentina (U.S. Geological Survey, 2009; Roskill, 2009). These countries accounted for 97.6% of the total lithium produced in 2010."

Jan 1, 2012

By Z. Hyder, M. Karmis

Underground or In-situ Coal Gasification (UCG or UICG), though not a new concept, is now attracting considerable global attention as a viable process to provide a "clean" and economic fuel from coal. Applying improved UICG technology to gasify deep, thin, and low-grade coal seams could vastly increase the amount of exploitable reserves. However, it is imperative that further development of this technology is based on integrating UCG practices and potential environmental impacts with accepted sustainability frameworks and processes. This paper evaluates the potential of UCG to conform to frameworks such as MMSD (Mining, Minerals and Sustainable Development), Natural Step and Green Engineering, in order to define its "sustainable" potential. The paper also discusses the potential contributions of UCG to sustainability during its design, operation, closure, and post-closure phases.

Jan 1, 2011

By T. J. Snell

Bolnore Village in Haywards Heath, Sussex, England, is a large development covering 8 to 10 hectares and expected to provide 1500 homes in five phases to assist in the continuing demand for new homes in the London area. Part of the development required housing on a relatively shallow slope found to have deep seated failure planes which are fairly prevalent in this part of Sussex. Locally the slope angle was around 20 degrees but more typically the gradient was 6 to 7 degrees. There were significant concerns about slope stability and bearing capacity due to pre-existing shear surfaces and the complex geotechnical profile. There was some evidence of instability in the form of residual shear surfaces and tension cracks. The development required terracing the site with retaining structures up to 5 meters in height, formation of access roads and foundations of new houses. The developer Crest Nicholson adopted a collaborative approach with consulting engineers Powell Tolner and specialist geotechnical contractor Keller Ground Engineering. The solution consisted of a novel combination of contiguous bored piling, ground anchors, and both block work and timbacrib retaining walls to ensure the geotechnical issues were adequately addressed within the time and cost constraints set by the team. The paper describes the geotechnics of the problem together with the design, practical implementation, and site progress achieved

Jan 1, 2006

By J. Wade Watkins, Joseph W. Horne, Arthur Matzick

"A successful procedure for the recovery of a valuable product from weathered tank-bottom settlings has been developed in the laboratories of the Bureau of lines and used in a field pilot plant. These heavy emulsion settlings, generally regarded by the industry as waste material, have usually been drained into open pits or storage ponds and eventually destroyed.Laboratory examination of the waste material shows it to consist essentially of a ""water-in-oil"" emulsion containing a considerable volume of congealed ""paraffin."" This paraffin is mainly high-melting-point wax; known in the industry as microcrystalline wax, for which there is an increasing demand.Because of the physical properties of this wax, the tank-bottom settlings are not responsive to conventional methods used for demulsifying ordinary crude-oil emulsions.The work upon which this report is based was conducted by the Bureau of Mines in cooperation with -the Kansas State. Board of Health and with special cooperative agreements-with the Cities Service Oil Co, Bartlesville, Okla., and the Bareco Oil Co,. Barnsdall, Okla. The studies were made under the general supervision of R. A. Cattell, chief engineer, Petroleum and Natural-Gas Division, Bureau of Mines, Washington; D. C., and H. C. Fowler, supervising engineer, Petroleum Experiment Station, Bureau of Mines, Bartlesville, Okla., and under the direct supervision of Ludwig Schmidt, senior petroleum engineer, Bureau of Mines, Bartlesville, Okla.Gratefully acknowledged are the assistance and cooperation given by the Cities Service Oil Co. of Oklahoma and especially by M. J. Kirwan, manager of production, and by Q. E. Beecher, general superintendent of production, Bartlesville, Okla., and to members of their staff at Oil Hill, Kans.The assistance and suggestions of V. R. Oakley, general superintendent, E. R. Wiles, director of research, L. G. Willis, field engineer in charge crude-oil supply, and Gerald DeWalt, chief chemist, and his staff of the Bareco Oil Co., Barnsdall, Okla., were of much value in the laboratory and recovery work."

Mar 1, 1946

By Mavor S.

Further discussion at the Mining Institute of Scotland's general meeting held in Edinburgh, 12 February 1916, with D.W. Mowat, president, in the chair, of a paper published in Trans. Inst. Min. Engrs., 1915, vol. L, p.625 and discussed vol. L, pp.92, 433, 468, and 704 included comments by Mowat D.W. and the author's reply

Dec 1, 1916

By Ren G. Dong, Kristine M. Krajnak, Dan Welcome

Continual occupational exposure to vibrating hand tools can damage the neural, vascular and other soft tissues of the fingers. Rat tail models have been developed to investigate the biological responses of the tissues to vibration.1-2 However, the biodynamic response of the tail relative to that of the human fingers has not been characterized. The objective of this pilot study was to compare the transmissibilities of rat tails measured via a scanning laser vibrometer to those of human fingers gripping a handle. Methods In Part I of this experiment, four male Sprague Dawley rats (6 weeks old) were exposed to discrete 5g-rms sinusoids of 32, 63, 125, 160, 250, and 500 Hz. The rats were restrained in Broome-style restrainers with their tails constrained without compression to an exposure platform via elastic straps as shown in Figure 1. The platform was attached to a vertically vibrating shaker. The vibration was measured for the array of points shown in Figure 1 using a scanning laser vibrometer (Polytec) and the transmissibility calculated for each point on the tail relative to the reference points on the platform. In Part II, three male human subjects were exposed at the frequencies specified in Part I - with the addition of 1000 Hz - at a magnitude at the ANSI <0.5-hr limit up to 63 Hz, after which the acceleration was held constant at 5g-rms. The subjects gripped an instrumented handle at 20 N as shown in Figure 2. The transmissibility was calculated relative to the reference points on the handle. [ ]

Jan 6, 2006

By Shosei Ph. D Serata

The Stress Control Method of mine design provides enhanced engineering control over the behavior of underground structures in comparison to conventional mine design methods. The same Method can be applied to achieve design control of surface subsidence. The basic mechanism relating undergroued deformation and surface subsidence is disclosed by mine simulations, using the REM (Rheological Element Method) computer code, whose predictions have been validated by field measurements. The key components of the underlying mechanism of surface subsidence have been shown to be the stress envelopes formed in the process of underground excavation. It has also been demonstrated that significant control of surface subsidence can be achieved by designing the geometry and timing of underground excavation to regulate the formation of stress envelopes. A field example is given in this paper to illustrate this application of the Stress Control Method.

Jan 1, 1986

By Elizabeth Wademan

Recessions Eventually End ??Companies aggressively cutting production and inventories ??these will come in-line with demand ??U.S. home inventories are declining ??Housing becoming more affordable ??Global trade recovering after collapsing ??Lower oil prices should act as a stimulus Protracted Deleveraging Process Beginning ??Era of leverage-driven consumption is over ??Greatest destruction of consumer wealth since WWII ??Consumers will no longer be able to substitute capital gains for savings ??Shift towards savings will be a headwind to economic growth ???Paradox of Thrift?

May 1, 2009

By Yi Luo

Bolting the mine roof is one of the noisiest underground mining operations. The main contribution to the noise is the drilling of the roof bolt holes, especially drilling in hard rock. Previous research shows that the specific energy consumed in drilling bolt holes is inversely proportional to the bite depth (i.e., penetration per drill revolution). Less specific energy at a reasonably high bite depth means less energy is wasted in the drilling process for producing heat, bit wear and noise. Therefore, proper control of the drilling operation to achieve a reasonably higher bite depth can reduce drilling noise from its sources as a proactive noise control approach. In order to explore the feasibility and develop the proactive technology for reducing drilling noise, drilling tests have been conducted in laboratory settings. The preliminary results show that significant reduction in noise dose can be achieved by drilling in medium hard rock with uniaxial compressive strength of about 276 bars (4,000 psi) and at a reasonably high bite depth of about 4.6 mm/rev (0.18 in./rev). This paper presents the findings from laboratory experimental studies.