Search Documents

By Rex C. Bryan

An accurate and dependable ore reserve estimate is important to any mining company. It is also essential for development drilling and production planning to know about the distribution of the ore within the area to be mined. This paper will show that in the case of more variable deposits such as uranium, the use of geostatistics is superior to conventional techniques. Unlike conventional methods, geostatistics includes the importance of spatial orientation of measured variables. With the use of variograms in conjunction with kriging, a point or a block may be estimated along with its error of estimation. The existence of disequilibrium can create a severe problem in uranium 'ore reserve estimation, and mine and production planning. Disequilibrium can be simply defined as the ratio of chemical or assay values to gamma equivalent values calculated from the downhole geophysical gamma-ray logs. Various methods for adjusting for disequilibrium have been proposed. Most, however, have side stepped the consideration of disequilibrium itself being a regionalized phenomena; or its, relation to surrounding geology. This paper presents methods of incorporating both aspects. The East Dilts Pit at the Bear Creek Uranium Mine in Wyoming, has been used as a case study. Polygonal, triangular, and lognormal kriging and various disequilibrium adjusted methods, including multi-factor cokriging have been com- pared with the mining experience.

Jan 1, 1982

By H. A. Guess

Introduction. History and Production Statements. Southeast Missouri is the oldest of the large producing districts of the United States. The first recorded production from disseminated ores was in 1869, although for many years prior to that time lead had been milled from shallow pockets, and steady growth in production has been shown ever since, the greatest increases being during the past five years. The production by years for each of the operating companies from 1869 to 1907, inclusive, is given in Table I. In Table 11. is given the production by years from 1908 to 1912, inclusive, for the district as a whole, showing the tonnage of crude ore mined, yield in concentrates, average assay of concentrates; yield in metallic lead both per ton of crude ore and in total; also approximate value of the yearly production. It is interesting to note that the production for the 5-yr. period 1908 to 1912, inclusive, is practically equal to the total previous production, viz., the 39-yr. period 1869 to 1907, the summary being as follows:

Jan 1, 1915

By A. Vishwakarma, V. Himanshu, K. Dey

Underground mining is the most feasible method after extinction of shallow depth ore deposits. Longhole stoping method is the most technically advanced method for the faster excavation. In this method, the holes are drilled in the form of ring pattern and explosives are used for the rock breakage. During blasting, the explosive energy sometimes also breaks the non-ore material. The non-ore material gets included in the extracted ore and enhances the ore dilution. Few uncontrollable factors which affects the ore dilution are ore body characteristics, rock quality, insitu stress condition etc. Apart from uncontrollable factors, explosive energy and blast design also plays an immense role in ore dilution. In the blasting practice, the purpose is to effectively utilise the explosive energy for rock breakage. The optimum delay is required so that the blast holes attain adequate free face before the blasting. This paper deals with the optimisation of blast design parameters to reduce ore dilution in underground hard rock mining having narrow vein. The study was carried out using numerical simulation. The explicit dynamics based modeller of Ansys was used for this purpose. The parametric variations in the models were done to optimise the parameters. The burden has been optimised first by varying the width of the narrow vein. The blasts of a ring consisting of single hole were conducted in the model by varying the width of the narrow vein. The damage contour under different parametric variations were analysed. The experimental trial has been also carried out at Zawar Group of Mine, Rajasthan, India. The optimum parameter was decided based on the result of experimental trial and numerical simulation model. The output of the model shows that optimum burden for 3.5 m narrow vein width is 1.12 m and for 1.0 m, it is 1.54 m. This shows that the optimised burden is higher in the vein having lesser width as compared to the greater width. The presence of joints/changed media/interface (between the sidewall and narrow vein) is the major reason behind this. The wave gets reflected back very fast on coming in contact with joints in a 1.0 m narrow vein as compared to a 4.0 m narrow vein. This will quickly convert the compressive wave into tensile wave giving rise to tensile slabbing. Hence proper utilisation of explosive energy will take place for the breakage of rock mass when the width of the narrow vein is smaller. The burden obtained from the experimental trial and numerical simulation models is less than 2.0 %. Hence the numerical simulation based approach can be used for the assessment of the optimum burden for ring blasting in narrow vein under different geomining conditions. This helped in reducing ore dilution and maximization of ore recovery. In the future, empirical relationships may be developed by considering different geological discontinuity, the strength of the rock mass and explosive parameters.

Jan 1, 2024

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

Jan 1, 1886

By Stokes WPC

The capital requirements to develop a new mining venture are becoming very large; amounts of the order of US$1,000 million are not now unusual among estimates to bring new mining complexes into production. At the same time prevailing political and economic conditions are making it increasingly difficult to determine whether or not a project is likely to be viable. These factors emphasise the need to carry out thorough evaluation studies of all mineral prospects before making major investment. Additionally with the rapidly changing economic climate existing at the present time, it is becoming more and more necessary to carry out reappraisals of existing mines. An important function of both initial evaluations and reappraisals is to provide the operators of the mine with effective mining plans to ensure that the operation will meet its required economic targets. P, p M. tl p b, c v, s c 1 n 1 f r d c e c e u w Modern computers are well equipped to store and manipulate large amounts of data with speed and reliability. Their use in the mining field r is increasing and this trend serves to free f technical staff from much of the time consuming m and error prone hand calculations which were o formerly required in determining reserves and w carrying out all forms of mine planning. r Nevertheless, computers are not a universal

Jan 1, 1980

By G. L. Oldright

The past reputation of zinc as an ingredient in lead blast furnace slags has been bad. Zinc is thought of as a cause of accretions in the shaft of the blast furnace, of hot tops, of the formation of "zinc mush" in the crucible and forehearth, of leach rich slags, of viscous slags, and of low capacity in smelting.

Jan 1, 1934

By R. D. Nelson, S. D. Dahlgren

The conditions of temperature, strain rate, and total strain favoring deformation by grain boundary sliding, slip, or deformation with concurrent recrystallization were evaluated for alpha plutonium. Grain boundary sliding and slip were studied by examining structures formed on polished surfaces with 4.5 pct compressive deformation. The conditions required for recrystallization were determined from compressive deformation us time curves. At 110" C and at a strain rate of 10&apos;per min, deformation was almost exclusively by grain boundary sliding whereas slip was the predominant deformation mode at -10°C and lo-&apos; per min. Defarmation at intermediate tenzperatures and strain rates produced structures showing mixtures of grain boundary sliding and slip. Recrystallization occurred concurrently with deformation only after a critical strain was reached. About 14, 6, and 3 pct strain was required at 105", llO°, and lZO°C, respectively, before recrystallization started, irrespective of the strain rate in the range of lo-&apos;1 to 10&apos;4 per nzin. L HE temperature and strain-rate dependency of the modes of plastic deformation were evaluated for high-purity as-cast alpha plutonium. The techniques used to study slip and grain boundary sliding were similar to those employed previously for alpha plutonium by Bronisz and Gorum,&apos; and spriet.&apos; Recrystallization was investigated using the methods reported by Nelson.3 Bronisz and Gorum&apos; found that slip occurred on more than one slip system at room temperature, and suggested that grain boundary sliding also contributed to the deformation. spriet2 found that deformation was predominantly by slip at room temperature, and observed one to three orientations of slip traces in individual grains. In addition, he deformed polished samples at 10O° C, but concluded that the deformation character of alpha plutonium at 100° C and at room temperature were not essentially different. Several investigators reported that twinning was only occasionally observed.1&apos;2&apos;4 Nelson3 recently found in creep tests that high-purity alpha plutonium would recrystallize concurrently with compressive deformation at temperatures between 25" and 115°C. EXPERIMENTAL PROCEDURE Electrorefined plutonium having less than 300 ppm total impurities was received from Los Alamos Scientific Laboratory in the form of +-in. diarn cast rods. Major impurities were americium, <I00 ppm, and tungsten, (60 ppm. Less than 25 ppm each of other impurities were present. The rods were cut into right half-cylinders 0.35 in. long and 0.25 in. in diam, and the flat faces along the cylinder axes were metal-lographically polished. To avoid loss of the metallo-graphic polish by oxidation, the polished samples were deformed in a silicone fluid heat treating medium contained in a chamber evacuated to a pressure of lo-&apos; torr. Deadweight loading was used to compress the samples between 4.5 and 20 pct at strain rates between 10"4 and lo- &apos; min-&apos;. Strain rates were determined by dividing the total deformation by the elapsed time of the test, even though the strain rate was not constant during deformation. Curves of strain vs time for samples deformed with a constant compressive stress3 show that the strain rate changes by less than a factor of four during the testing of a given sample, which is small compared to the three orders of magnitude change in strain rate investigated. Two samples were loaded into an ordinary metallographic mounting mold and impacted by striking the mold piston with one blow of a 2-lb hammer. Deformation temperatures for the two impact samples were 25" and 90°C. The samples, following deformation, were washed in carbon tetrachloride and their polished and deformed surfaces were immediately inspected metallographi-cally. Subsequently, the deformation structures were replicated with acetate replicating tape for later electron microscope examination, and the samples were then repolished and etched to reveal the microstruc-tures of the deformed metal. Second-stage carbon replicas were prepared from decontaminated acetate replicas using the procedure developed by Miller, Bierlein, and astel.&apos; Additional samples, which were 0.35 in. long by 0.25 in. in diam, were used to obtain constant load deformation vs time curves. These samples were deformed 10 to 20 pct with loads of 15 and 20,000 psi at 120°C; 30, 45, and 55,000 psi at 110°C; and 20 and 30,000 psi at 105°C. Samples were polished and etched to determine whether or not recrystallization or twinning had occurred during deformation. RESULTS AND DISCUSSION The experiments showed that alpha plutonium deforms by grain boundary sliding, slip, and deformation with concurrent recrystallization. Deformation by twinning was insignificant. Metallographic examination of polished and deformed surfaces revealed grain boundary sliding and slip. The start of recrystallization was ascertained from constant load deformation vs time curves. Deformed surface structures of samples compressed 4.5 pct under four different conditions of temperature and strain rate, Fig. 1, show how the deformation mode changes from predominantly grain boundary sliding to predominantly slip with increasing strain rate and decreasing temperature. Deformation at 110°C and 10" 4 min-&apos;, Fig. l(a), was predominantly by grain boundary sliding. Only a few slip traces can be seen in Fig. l(a).

Jan 1, 1969

By W. J. Long

The gradual depletion of high-grade mineral deposits and the necessity for development of lower-grade deposits together with the increased demand for nonmetallic minerals has increased the importance of the ore-dressing field during recent years. There is strong need for development of new ore-concentration methods and-machines to keep pace with the constant changing of marketing specifications and requirements resulting owing to the many new uses made of mineral products by the metallurgical industry.

Jan 1, 1948

By C. O. Ruud, R. E. Siemens, D. Chandra

The mineralogical constitution of a lateritic ore dictates the type of metallurgical process that can be used to extract valuable metals such as nickel and cobalt . To provide needed mineralogical information on the interrelationships of the metals contained in domestic laterites , the Bureau of Mines awarded a grant to Denver Research Institute to study the transition - type , low - grade laterites found in northern California and southern Oregon . For comparison , limonitic - type laterites from New Caledonia and the Philippines were also studied . X-ray diffraction , electron microscopy , electron beam analysis , and conventional petrography were used to determine the mineralogical associations of nickel and cobalt in the laterites . Results showed that for both laterite types studied most of the nickel and minor amounts of cobalt are associated with the mineral geothite ( FeO ( OH ) ) . Most of the cobalt and minor amounts of nickel are associated with a mixed manganese oxide (wad ) mineral .

Jan 1, 1983

By Paul W. Weiblen, Louis J. Cabri, Rolando Lastra

"Preliminary tests were done to determine whether comminution by electric-pulse disaggregation, or E-PD (cf. Rudashevsky et al; 1995), was more effective than using conventional crushing for Merensky Reef ore. A hand sample of the Merensky Reef was sawn in two: then one sub-sample was comminuted to .2 mm using E-PD at the University of Minnesota, and the other sub-sample was crushed to .2 mm using a conventional jaw crusher at CANMET.The products of the electric-pulse disaggregation and jaw crusher were fractionated by sieving and by a separation using a heavy liquid with a specific gravity of 3.3, because the proportion of platinum-group minerals (PGM) and sulphides to silicate minerals is very low. Thus, four mineral separates were produced: .2000 + 833 µm, -833 +208 µm, -208-µm float and -208-µm sink. All the mineral separates were studied by image analysis (Lastra et al; 1998). The main objective was to determine the liberation of gangue (silicate minerals), chromite, pyrrhotite, chalcopyrite, pentlandite and PGM. In the case of the PGM, a specific image analysis program was written to search and measure these minerals.The results show that the liberation obtained for gangue was similar (~99%) using either method of comminution. However, the liberation obtained for chromite (~89% vs. ~38%), pentlandite (~50% vs. 1%), pyrrhotite (~56% vs. ~38%), and PGM (~56% vs. ~1%) by E-PD was higher than that obtained by conventional jaw crusher, whereas the liberation obtained for chalcopyrite (~20% vs. ~71%) by E-PD was lower. Nevertheless, the image analysis of the products also showed that the PGM are strongly associated with pentlandite. Thus, for the Merensky Reef, liberation of pentlandite from the gangue minerals and chromite is important to recover more of the PGM. This maybe be significant because, in addition to increased recovery of platinum-group minerals (PGM), Merensky Reef pentlandite also contains significant quantities of valuable platinum-group elements like Pd and Rh (Cabri, 1981; Cabri 1988, Kinloch 1982, Peyerl 1983). Hence, the results indicate that for the Merensky Reef, electric-pulse disaggregation would represent a better comminution operation than a conventional jaw crusher would. In addition, the greatly improved liberation for chromite may find application for the PGM-rich UG2 chromitite."

Jan 1, 2003

By Ting Ren, Jon Roberts, Zhongbei Li, Ming Qiao, Jianming Wu

Spontaneous heating of coal continues to present a health and safety hazard in underground coal mines. The influence of seam gas composition on gas flow dynamics and distribution characteristics in the active longwall goaf has not been studied in-depth, and corresponding effective proactive goaf inertization strategies for preventing potential spontaneous heating from occurring have limited investigation. To advance this knowledge, an 80-m-height goaf model was constructed and developed based on specific conditions of an Australian underground coal mine, and onsite gas monitoring data was collated to verify base model results, which allowed for various scenarios of seam gas composition to be simulated and investigated with confidence. This study involved modeling five different gas composition scenarios for the goaf atmosphere, namely, 100% CO2 (case 1), 80% CO2 and 20% CH4 (case 2), 50% CO2 and 50% CH4 (case 3), 20% CO2 and 80% CH4 (case 4), and 100% CH4 (case 5). Simulation results show that O2 is primarily distributed at the middle and upper part of the CO2- dominant goaf model, while it is mainly layered at the floor level of the CH4- dominant goaf model. N2 is superior to CO2 in the goaf inertization for the CO2- dominant goaf model, whereas CO2 performs better than N2 for the CH4- dominant goaf model. The optimal inert gas flowrates for case 1 to case 5 are 1.5, 1.75, 0.75, 0.5, and 1.0 m3/ s, and the oxidation zone area is reduced by 55.76%, 67.21%, 58.04%, 78.17%, and 81.82%, respectively. The simulation results allow for increased insight and understanding of the gas distribution patterns in the active goaf with different seam gas composition and the development of corresponding proactive goaf inertization practices, thus minimizing potential spontaneous-heating-related hazards and improving mining safety.

Sep 26, 2023

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By M. Saghaeian, R. Hejazi, Sheikhzadeh. V., A. Abazarpoor

"The morphology of iron ore concentrate particles is known to influence several properties of iron ore pellets, including drop number, compression strength, and reduction properties. This study aimed to determine why grinding methods and particle morphology influence green pellet properties. Particle morphology can be directly related to the grinding method: ball mill (BM) or high pressure grinding roll (HPGR). In this research, two iron ore concentrates, namely Gol-e-gohar and Ardakan, were ground by a BM and HPGR to produce a suitable Blaine value for pelletizing (nearly 1,900 cm2/g). Morphological features of particles were subsequently investigated by sieving and cyclone sizing for particle size distribution, the Brunauer-Emmett-Teller (BET) and Blaine methods for specific surface area (SSA) and scanning electron microscopy (SEM) for the evaluation of shape descriptors. It was concluded that HPGR resulted in generating a greater proportion of fine particles compared to ball milling. The BET results showed that the SSA of HPGR pellet feed was higher than that from the BM due to a greater proportion of cracks, indents and bulges and the creation of new fracture surfaces. SEM images processed by ImageJ software indicated that particles ground by the BM tended to be more rounded and less elongated than HPGR particles because of the breakage model of each method. To show the effect of morphology on the green pellet quality, green pelletizing was performed in a pilot pelletizing disc. The HPGR pellet feed had a higher drop number in comparison to the BM pellet feed, due to the angular and rough shape of the particles.INTRODUCTIONThe demand for fine or ultra-fine particles as feed material for ceramics, composite materials, and mineral processing is on the rise (Kotake, Kuboki, Kiya, & Kanda, 2011). The final concentrate of iron ore processing plants (filter cake) has a size range roughly between 0 and 300 µm, depending on the liberation of Fe containing particles (Meyer, 1980). In general, to produce a suitable pellet feed of appropriate quality, Blaine numbers of 1800–2000 cm2/g should be achieved (Van der meer, 2015)."

Jan 1, 2016

By R. Barany

The heats of formation of seven substances were determined by solution calorimetry. At 298.15° K, the heat of formation of lithium sulfate from lithium, rhombic sulfur, and oxygen was -343.1 ± 0.7 kcal/mole, and the heat of formation of lithium sulfate monohydrate from lithium, rhombic sulfur, oxy-gen, and hydrogen was -414.3 ± 0.7 kcal/mo1e. For the silicates, the heats of formation at 298.15° K from the elements were kaliophilite, -503.8 ± 0.5 kcal/mole; leucite, -721.6 ± 0,8 kcal/mole; eucryptite, -505,2 ± 0.6 kcal/mole; alpha-spodumene, -727.9 ± 0.9 kcal/mole; and beta-spodumene, -721.1 ± 0.9 kcal/mole. The corresponding heats of formation at 298.15° K from the constituent oxides were kaliophilite, -42.7 ± 1.1 kca1/mole; leucite, -42.8 ± 1.1 kcal/mole; eucryptite, -16.1 ± 0.7 kcal/mole; alpha-spodumene, -21.0 ± 0.7 kcal/mo1e; and beta-spodumene, -14.3 ± 0.7 kcal/mo1e.

Jan 1, 1966

By H. Saint-Raymond, F. Gruy, P. Gardin, M. Cournil

"The control of inclusion elimination is getting more and more important to obtain clean steel. This paper presents a methodology under development for predicting cluster growth and elimination in ladle - RH system. The first key point is to express the collision efficiency, which is very specific for alumina cluster due to the non-wetting fluid. Second, a description of the two-phase flow in the system is necessary. In our calculations with Fluent CFD package and Lagrangian approach for bubbles, bubble growth is implemented, which improves the predictions. Using global reactor decomposition makes possible the prediction of the time evolution of cluster distribution. Important effect of fractal dimension is demonstrated.IntroductionElaboration of new steel grades requires not only to have a high purity in terms of C, O and N content but also to eliminate particles such as alumina or slag droplets. Flow optimisation making easier inclusion elimination is then a key figure to satisfy cleanliness requirements. Mathematical models of flow and inclusion behaviour are widely used for this purpose (1, 2). But having a predictive tool is still a challenge, because the number of phases is important in steelmaking industry: liquid steel, slag layer, bubbles and inclusions (with a large range of composition and rheology). The paper presents the methodology which is developed at IRSID to predict oxygen content evolution during RH degassing.The main mechanisms which have to be considered are :-inclusion growth by turbulent aggregation of elementary inclusions (keeping in mind that liquid steel is a non-wetting medium for inclusions); the difficulty is to express collision efficiency for alumina particles,-inclusion removal by flotation; the difficulty for alumina clusters stems from the complex morphology of particle; fortunately, the use of fractal concept makes it possible to cope with this problem.The paper describes the general modelling of inclusion removal taking into account the previous mechanisms. Hydrodynamic parameters are obtained by means of Fluent CFD package and a specific coding is developed for cluster growth."

Jan 1, 2001

By M. C. Flemings, F. R. Mollard

Two-phase Pb-Sn alloys, ranging in compositiotz from 12 to 26 at. pct Pb, were unidirectionally solidified in a convection-fvee system, with thermal gradients in the liquid of up to 480°C per cm. Plane front solidification Loas achieved in all alloys at sufficiently steep gradient and slow growth rate. Conditions causing breakdown of the interface to a cellular or dendritic structure were roughly as predicted by a sinlple constitutional supercooling criterion. Structures of alloys of near-eutectic composition, solidified with plane front, exhibited a lamellar structure; the alloys furthest from the eutectic exhibited a rod-like morphology. Assumptions used in a previous paper for calculations of solute redistribution in two-phase plane front growth are shown to be reasonable for Pb-Sn alloys. Results of calculations are in good agveement with experiment. These show that variations in growth rate during solidification of the composite produce marked changes in average composition of the solid. IN a previous paper, Part I,&apos; conditions necessary for plane front solidification of two-phase alloys were discussed and calculations given on solute redistribution in this type of solidification. This paper, Part 11, describes experiments on Pb-Sn alloys, designed to check the assumptions of the analyses presented, and to demonstrate their applicability to a given alloy system (Pb-Sn). APPARATUS AND PROCEDURE General. A vertical crystal growing unit was built for the study as described below, and "normal solidification" employed throughout (i.e., the ingot was completely melted except for a portion near the bottom end and then solidification initiated). The furnace was designed to permit achieving very low interface velocities, and steep gradients, in essential absence of convection; it is sketched in Figs. 1 and 2. Simple heat flow considerations indicated choice of a small-diameter specimen (ingot) to achieve high thermal gradients; ingot size chosen was 0.3 cm in diam. The ingots were held inside silica tubes 0.06 cm wall thickness. The requirement for an essentially convection-free system was met by use of the vertical furnace with the heat source over the heat sink, as well as by use of the small diameter ingots. In addition, by selection of tin-rich Pb-Sn alloys, the diffusion boundary layer (lead-rich) was denser than the bulk liquid and would not cause convection. The only apparent driving force for convection in this system was the small transverse temperature gradient resulting from heat flow into the samples from the furnace. Such convection must have been small, however, since 1) no temperature fluctuations in the melt were noted in the recordings, which would have indicated turbulent convection, and 2) experimental results obtained and described below could not have been achieved in presence of significant convection. Ingot Preparation. Pb-Sn alloys ranging from 12 to 26 at. pct Pb were prepared from high-purity lead and tin (99.9999 pct pure metal). Each alloy was prepared by first melting the pure metals in the proper ratio in air, in a Pyrex container. The melt was then stirred thoroughly with a graphite rod and cast into a preheated graphite mold. Ingots were then prepared from these castings for use in the actual experiments; each ingot consisted of a rod of alloy, 15 cm long in a 25-cm-long transparent fused-silica tube, 0.3 cm ID and 0.06 cm wall thickness. One chromel-alumel thermocouple, made with 0.004-in.-diam wire and protected by a two-hole alumina tube, was inserted into each ingot. The 1.5 cm of the thermocouple nearest the bead were protruding from the alumina tube and were coated with a very thin layer of boron nitride paste which provided electrical insulation while allowing good heat conduction. The electrically welded junction size was about that of each wire and the cross section of the two wires represented about 0.3 pct of the sample cross section. Including the coating, the thermocouple cross section still represented less than 0.5 pct of the ingot cross

Jan 1, 1968

By F. Garcia-Carcedo

This research aimed to develop a clean technology for the production of ZnO from residues generated by the steel making industry. Scientific and technologic parameters were both investigated in order to define an industrial methodology allowing the integral recycling of EAF dusts. A reengineering of the Waelz process was perform,~d, aiming to produce a clean fraction of ZnO, fluorine free, as well as a slag enriched in metallic iron, which can be recycled in electric arc furnaces. The technical conditions used to produce the ultra pure fraction of ZnO are described. The magnetic separation of the EAF dust allowing the production of a phase high in iron and recyclable to the electric arc furnace is also discussed. Thermodynamic of the volatilization of all the elements contained in the EAF dust was performed in order to better control the thermal process in the rotary kiln. Tests were run using different reducing agents, weakly or highly reactive, aiming to determine their specific efficiency.

Jan 1, 2000

By Charles L. Kimbell

The final 26 tables of this chapter, tables 25-50, extend and expand the statistical series on production that was started in the 1963 edition of the "Area Reports: International" volume of the "Minerals Yearbook" and that was subsequently updated and expanded in the 1965 and 1967-89 editions. Continuing the practice started in 1989, a column has been included in each of these tables providing a 5-year average for 1986-90, inclusive. This should provide a clearer picture more rapidly of the role of each major producer over the 5-year period. The listing order of major producers, however, continued to be, as in past years, in descending order of rank in the year of review, 1990. With the inclusion of silver and uranium in the 1988 edition of this chapter, this group of tables now includes each of the crude minerals that ranked from 1st to 19th in 1983 terms of value of their output (as well as four others of lesser rank). These 23 crude mineral commodities accounted for 93% of the estimated value of world crude mineral production in 1983. In addition, world output of five key downstream products-aluminum, steel, cement, nitrogen in ammonia, and refined oil-are included because of their significance as products.

Jan 1, 1993