Search Documents

By William J. Miles

The markets and applications of Wyoming bentonite deposits are primarily determined by the functional properties of a bentonite ore which results from the unique mineralogy and chemistry of each deposit. Commercial bentonite products contain sodium montmorillonite as the major mineral component, with minor concentrations of accessory minerals such as quartz, opal (silica hydrate), mica, feldspar, gypsum and zeolites. The chemical composition of the sodium montmorillonite influences the functional properties of the bentonite in significant ways. The type and concentration of various accessory minerals also influence the acceptability of the bentonite in each market.

Jan 1, 1995

By VIVEK KASHYAP, PATRICK TAYLOR

The presence of iron in sphalerite induces the formation of zinc ferrite (ZF) during roasting. Zinc refinery residues (ZRR) and electric arc furnace dust (EAFD) contain a significant amount of zinc ferrite and are difficult to treat. According to the literature, up to 71% ZF has been found to be present in ZRR. The dissolution of zinc ferrite is inefficient even in aqua regia. The Waelz process is an existing process to recover zinc from electric arc furnace dust by reduction using carbon monoxide followed by the volatilization of zinc. In this study, zinc was selectively extracted from zinc ferrite by partial reduction of zinc ferrite at relatively low temperature followed by leaching in dilute sulfuric acid (20 g/L). Pure zinc ferrite samples were partially reduced to zinc oxide and magnetite by using H2 gas as a reductant. The presence of magnetite and zinc oxide was confirmed by X-ray diffraction (XRD) technique. A maximum of 95%zinc extraction was achieved after leaching with sulfuric acid on the reacted samples. The paper also discusses the effect of time, temperature, and concentration of H2 in the reducing gas on the extraction of zinc and iron from ZF.

Sep 16, 2020

By Steven K. Ruggieri

This report describes the operation and maintenance of the Mobile Inert Gas Generator for use in the Remote Sealing System for fighting underground coal mine fires. Seals are emplaced in mine passageways between the fire zone and the rest of the mine isolating the fire zone from the mine. The seals consist of fly ash that has been pneumatically conveyed via inert gas through a borehole connecting the surface and the passageway, Inert gas is used as the fly ash seal transport medium (instead of fresh air) since the introduction of large volumes of fresh air in the vicinity of the fire zone would be undesirable. The inert gas generation equipment is mounted on two flatbed trailers, the "hot" trailer and the "cold" trailer. The hot trailer contains the combustion and cooling equipment. The cold trailer contains the moisture removal and compression equipment necessary to convey the fly ash. The system is self-sufficient and requires only fuel and fly ash deliveries. The Inert Gas Generator has been thoroughly performance tested and has been operated in the field for approximately 200 hr. The system was employed in the demonstration of the entire Remote Mine Sealing System at the Jenney Mine in the Fall of 1978. The system is currently available for fighting any future underground coal mine fires.

Jan 1, 1980

By A. N. Baldwin

This report documents the work performed under Bureau of Mines Contract J0265029 to study and develop two innovative mining systems: ? An underground auger capable of augering into the right and left ribs without repositioning the machine ? A conventional mining system employing recently developed innovative machinery. The report is separated into two volumes to document the two studies separately. Volume I describes work performed and the recommended concept for a bidirectional auger. Volume II describes the studies of mining equipment performance and mining plans developed to determine a conventional mining plan offering improved productivity.

Jan 1, 1977

A search for the keyword nano reveals that it has not made a significant entry into the mineral processing research literature. In contrast, the terms micelle, colloid, interface, and monolayer are well established there. By considering nanoscience as colloid and interface science at the nanoscale, it is claimed that several previous and current investigations in the broad field of mineral processing fall under the umbrella of nanoscience. Several examples from hydrometallurgical processing systems (invisible gold and activated carbon in gold extraction; monolayers, reverse micelles, and microemulsions in solvent extraction; nanobiofilms and nanoparticles in biohydrometallurgy) are highlighted in support of this view.

Sep 13, 2010

By Paul S. Goodman

This report examines the effectiveness of bonus plans in the coal industry. The analysis uses theoretical, literature review and empirical approaches to determine the impact of bonus plans on safety and productivity in underground coal mines. The basic finding is that the modal bonus plan in underground coal mining does not have a major impact on productivity and safety indicators. The design of the plan, or organizational factors, and the process of introducing the plan all contribute to its relative ineffectiveness. Strategies and options for designing effective plans are presented.

Jan 1, 1987

By W. W. Adams

The United States Bureau of Mines, in cooperation with the National Send and Gravel Association conducted a safety contest in 1929 Among producers of sand and gravel. Only 26 plants were enrolled, as the contest was late getting under way. It is hoped that a ranch larger number of plants will be represented in the safety competition of 1930. Two trophies, both of which were provided by Rock Products magazine, were awarded at the end of the contest; one trophy was given for the best safety record among plants working 100,000 or mare man-hours during the year and the other for the beat record among plants working less than 100,000 man-hours. The trophies were presented to representatives of the winning, companies on January 29, 1930, at the annual convention of the National Sand and Gravel Association at Memphis, Tenn.

Jan 1, 1930

By Jeffrey S. Newman

This report presents a summary of the results of a four-phase program conducted for the Bureau of Mines to evaluate underground mine fire detection systems. In addition, Phase IV is presented in detail. The major accomplishments of this program are: 1) quantification and prediction of the distribution of fire products in a mine pas¬sageway; 2) quantification of "equivalent protection" by fire detectors as contained in Title 30 of the Code of Federal Regulations; 3) definition of detection criteria; 4) design of a detector test program for determining detector spacing requirements; 5) design, construction, operation, and calibration of a fire test apparatus for evaluating mine fire detectors; 6) quantification of several mine fire sources; 7) evaluation of several fire detector types including heat, CO and CO2 gas, and ionization smoke detectors; 8) development of generalized spacing criteria for mine fire detectors; and 9) development of performance specifications. Reports for Phases I through III are included in Appendices.

Jan 1, 1984

By Henry P. Chandler

COMBINED sales of abrasive materials in the United States during 1956 increased at about the same rate as the value of the Gross National Product in terms of 1954 dollars,3 which was nearly 3 percent. However, some segments of the industry did not follow the general pattern. Sales of abrasive grinding wheels increased 9 percent in value. Sales of surface-coated abrasives declined 5 percent in quantity hut increased 1 percent in value, Production of crude silicon carbide in the United States and Canada advanced both in tonnage and value, but that of abrasive-grade [ ]

Jan 1, 1958

The support of the roof in coal mines remains a critical safety issue with 3 fatalities from roof falls in 2007 and 430 injuries from roof falls in 2006. A snapshot survey by the authors of room design and support details as well as unplanned falls of ground in the industry revealed some useful data concerning support use, seam details, fall dimensions, bolt lengths and spacing and the stand-up time.

Jan 1, 2009

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By R. S. Dean

A large metallurgical experiment station at Salt Lake City to house the works of the Bureau of Mines in the intermountain area properly has long been projected. It finally became possible when a Public Works Allotment of $300,000 was set aside for building and equipment. With the new building assured, the Bureau of Mines decided to move the headquarters of its Metallurgical Division from Washington, D. C., to Salt Lake City, Utah. It was felt that this move would simplify they administrative work of the chief engineer of the division, as all stations devoted primarily to metallurgical work are west of the Mississippi. These include Rolla, Mo.; Minneapolis, Minn.; Pullman, Wash.; Reno, Nev.; Berkeley, Calif.; Boulder City, Nev.; and Tucson, Ariz. In addition to these stations will groups, of investigators working on metallurgical problem, are maintained at Pittsburgh, Pa., and College Park, Md. Salt Like City was clearly a more central point for the direction of this scattered work than Washington, D. C. The building (fig. 1, A and B) was designed from general plans worked out by the authors of this paper. Contraction was begun in March of 1939, and by the end of the year the Metallurgical Division had moved, into its now quarters.

Jan 1, 1940

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

[Participating Scholarship Colleges and Universities 138 AmerCable 130 Andalex Resources, Inc 82 Behre Dolbear & Company, Inc 83 Commercial Testing & Engineering Company 86 Continental Conveyor & Equipment Co 87 Crane & Hoist Sales Inc 12 Crested Butte Mountain Resort 88 Dakota Coal Company 89 Empire Machinery Company 90 Energy West Mining Company 91 GH Hensley Industries 92, 93 Hitachi Construction Machinery (America) Corp 96 Ingersoll-Rand Company 131]

Jan 1, 1998

By Thierry Bernard, Pierre M. Vuillaume, Michel Kiszlo

"In the context of its studies for the trench ministry of the environment and for the French national coal board, INERIS (the French institute for the industrial environment and hazards, formerly CERCHAR) has made a complete critical survey of the methods generally used to reduce the levels of blastingvibrations."

Jan 1, 1996

By A. E. Seaton

In this paper it will be my endeavor to trace the development of the marine engine and its appurtenances, and the general progress that has taken place in marine engineering generally during the past fifteen years, rather with the object of attributing much of it to the successful efforts of the makers of iron and steel, thereby rendering my thanks to them for the valuable service they have contributed to my profession, than to recount what has been achieved by the skill, ability and perseverance of my colleagues in shipbuilding and engineering. The engineer has been at all times dependent on the ironmaster, and on more than one occasion his progress has been barred by the inability of the latter to overcome some obstacle to success in his manufacture. But on the other hand, it is equally true that the ironmaster has often been ahead of the engineer, and has been prepared, long beforehand, to supply that which would make a success for the marine engineer if he would avail himself of it.

Jan 1, 1891

By R J. Wood

Raise drilling (or raise boring) is not a new technology or methodology. The first raise drilling machine was developed by The Robbins Company (TRC) of the USA in 1962. TRC manufactured the first tunnel boring machine (TBM) in 1952 and Jim Robbins, the founder of the company wanted to ‘turn the TBM concept on its head’ so to speak.Many improvements have ensued in the 50 years since the first machine. Such improvements include advances in the drill rod and thread design, cutters and reaming heads. Raise boring would not have been possible without the development of the tungsten carbide insert cutters and there have been big advances in both the carbide technology and in the mechanical design of the cutters.Over time mines have developed deeper with a greater use of diesel equipment resulting in greater ventilation requirements. This in turn means larger and deeper ventilation shafts. There have also been improvements in directional drilling techniques. This all combines with the need and ability to construct larger shafts using the safe method of raise drilling. With suitable geotechnical conditions the RBR900VF is capable of drilling shafts to a diameter and depth of greater than 8 m and 2000 m respectively. Greater diameters are possible over shorter lengths with suitable ground conditions.The RBR900VF was designed and manufactured to specifications developed by Macmahon. This machine has the greatest thrust and torque capability of any machine in the world. It enables cutters to be more heavily loaded in the larger diameter heads and this is essential for efficient rock excavation. Additional features of the new machine include minimal manual handling to provide a safer working environment and higher strength steel for the drill rods providing additional safety margin.CITATION:Wood, R J, 2014. A revolution in raise boring – the development of the RBR900VF, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 171–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Kate Satish

M/s Konkan Railways Corporation are constructing 760 kms long rail road in the Western Coastal Region of India. The rail road encounters 75 tunnels through the Western Ghats of India with a total length of 78.35 kms, the longest tunnel being 6.5 kms long. The tunnels are of horse shoes shape having a cross section of about 37 Sq.meters

Jan 1, 1996

By K. N. Santini, J. M. Barker

The perlite industry in the United States continued to undergo rapid change and increased competition last year as it did in 2002. U.S. production in 2004 was 510 kt (562,000 st),an increase following five consecutive years of decline (Table 1). Perlite is exported to Canada and to the Pacific Rim. These partially offset imports. Perlite imports from Greece to the eastern and Gulf Coasts of the United States declined by about 22 percent after reaching a record 240 kt (264,000 st) in 2003.But their market remains protected by high rail rates from western U.S. plants. Minor imports of perlite persist by Termolita from Mexico.

Jan 1, 2005

Ladies and gentlemen, distinguished guests and fellow members of The AusIMM, good morning.   Thank you for the opportunity to address you all today, Crown Minerals are very pleased to be associated with the conference again this year, and I commend the committee on their organisation and delivery of this yearÆs event.   As you can see from the topic of my discussion, I would like to broach the subject of collaboration between ourselves û Crown Minerals û and you our clients, and convince you that we are on the right track but can each do more.

Jan 1, 2007