Search Documents

The Skorpion Zinc Project demonstrated the viability of the production of zinc from non-sulphide (commonly called ?zinc-oxide?) ores, using the leach/solvent extraction/electrowinning process route. The success of Skorpion raised the profile of a number of other zinc oxide deposits, considered to be similar. However, a study of three such deposits demonstrates that the application of whole-ore-leaching may be limited and that the concentration of zinc, or at least the separation from acid-consuming gangue minerals, prior to leaching is essential to the successful recovery of zinc from these deposits. The recovery of zinc is dependent on an understanding of the geology of the deposit, the mineralogical association of zinc minerals with gangue minerals (Boni, 2005) and limitations of mining practice. Flow sheet development and the associated metallurgical test work to derive an economically viable treatment route from two of these deposits are discussed. Key parameters affecting zinc recovery by gravity separation and flotation are presented, demonstrating that even minor differences in mineralogy have a profound impact on zinc recovery and reagent consumption. The study also deals with the determination of appropriate design parameters through metallurgical mapping of the dense media separation process.

Jan 1, 2008

Adsorption Effect on Multi-Heavy Metal Ions in Wastewater by Water-Washing Waste Saccharomyces cerevisiae

Sep 13, 2010

By D. E. Pollock

Recent NIOSH published information has shown an increase of rapidly progressive coal workers? pneumoconiosis (CWP) in the southern Appalachian coal region (SAR) of the U.S., despite the fact that compliance data indicates that most coal miners have been exposed to coal mine dust concentrations below the statutory limit of 2.0 mg/m³. While the exact cause of these elevated CWP levels in the SAR has not been established, several factors may be contributing to the increase in occupational lung disease among coal miners. The mining of high rank coal is known to lead to higher CWP rates, and this type of coal is mined in a portion of this region. Also, a high percentage of the mines in the region are on reduced dust standards because of the high silica content of the airborne dust resulting in miners possibly being exposed to excessive amounts of respirable silica dust. Exposure to excessive amounts of respirable silica dust can lead to silicosis, a disabling and potentially fatal lung disease. NIOSH's Respiratory Hazards Control Branch has been investigating the possible causes that would account for the observed higher trends in disease progression through literature review, data analysis, and in-mine surveying. The investigation to date has revealed that underground mines are faced with cutting large amounts of rock in order to maintain haulage clearances. Cutting rock not only increases the potential for silica exposure, it increases the requirement for machine maintenance which was a concern observed during dust surveys conducted by NIOSH. Over half of the mines operating in the SAR are on reduced standards due to high silica content. Adequate face ventilation of the continuous miner and roof bolter and limited down-wind operations from the miner are also issues of concern and items which require the constant attention of miners operating in these conditions. Disclaimer: Mention of any company or product does not constitute endorsement by the National Institute for Occupational Safety and Health.

Jan 1, 2009

By GEORGE T. Harley, Walter R. Storms

This paper, which describes mining mothods at International Minerals & Chemical Corp, 'e. potash mine. in. Eddy. County, N. Mex., is one of a sories being prepared by the Mining Branch of the Bureau of Minos. on mining method a and practicos in, various mining districts of the United States. The mine shafts and. surface plant or International Minerals & Chemical Corp. are situated. in. sec.. 12, T. 22 S., R. 29 E., N. M. P. M., about 26-1/2 miles by paved highway east of the city of Carlsbad (figs. 1, 2, and 3). A spur line of the Atchison, Topeka & Santa Fe Railroad connects the mine with the Clovia-Pecos branch of the same road near Loving, a few miles south of Carlsbad. This spur also serves the refinery of United Staics Potash Co. This report gives. the history and describes the geology of the district. Methods of prospecting, exploration, sampling, and estimation of tonnage and values are explained; development and mining methods are discussed in con- siderable detail; transportation, ventilation and drainage are outlined; safety measures are noted; and the wage scale and organization are mentioned.

Jun 1, 1949

This article presents a proposal for the rehabilitation of the mined area of the Mogiana quarry. The Mogiana quarry produces material used in civil construction and is situated in the Brazilian State of Spo Paulo in the kilometre six of the Mogf Mirim - Itapira highway. The mineral exploitation in the Mogiana quarry provokes modifications in the environment such as alterations in the relief, vegetation, quality of the air, water and landscape. Through previous study of the area it was verified that after the closure of the exploitation the mine should be occupied mainly by pasturage. At the closing of the mine the exploitation benches, berms and slopes in general as well as the surrounding areas should be covered with a layer of soil and vegetated with native species in order to mitigate the negative impacts caused by the mine. The rehabilitation project of the area is based on the probable future use of the area, located between agricultural cultivations and cattle creation. The great alteration of the relief and soil would make future use of the area for agriculture difficult. It is more suitable t0 animal creation, mainly cattle. The high and thick rock slopes originated by the mining should be covered by vegetation, where possible, to reduce the negative visual impact. Obviously several measures will be necessary to reduce the impacts on the environment during mining. The final and definitive reclamation will only be possible after abandonment of the area. The main aspects of this reclamation process will be discussed in this paper.

Dec 6, 2010

By J. -H. Wu, S. Nishiyama, Y. Ohnishi

The behaviors and stress distributions of the inclined jointed rock masses with different dip angles obtained from DDA are compared to the results of laboratory tests. By calculating the block stress distributions, it is confirmed that DDA can reproduce the arching around the trap door when lowering the trap door. The shapes of arching change with the angles of inclined layers. In addition, the earth pressures acting on the trap door shows non-symmetrical distributions when the layers are not horizontal. The stress concentration occurs in one side of the rock masses close to the trap door. Furthermore, the surface settlements are also related to the inclined angle, and the loosening zone in rock masses can be different from Terzghi’s theory [1]. Since, simulations have good agreements with the laboratory test , it demonstrates the applicability of DDA to explain the mechanical behaviors of tunnel, such as arching phenomenon, non-symmetrical earth pressure distributions acting on the trap door, and the surface settlement profile in the jointed rock masses. Dans cet article est décrite l’étude numérique du perçage d’un tunnel dans un massif de couches rocheuses jointes inclinées. La simulation à l’aide de l’Analyse de Déformation Discontinue (DDA), en faisant varier l’angle d’inclinaison des couches de roche, nous apporte des résultats en termes de distributions de contraintes et de comportement des couches, résultats qui sont ensuite comparés avec des résultats de tests en laboratoire. Les résultats confirment le fait que la DDA est capable de reproduire le phénomène d’arcage autour de la trappe lorsque la trappe s’abaisse. Les formes d’arcage varient selon l’angle d’inclinaison des couches de roche. Par ailleurs, lorsque les couches ne sont pas horizontales, la distribution de pression agissant sur la trappe est assymmétrique. La concentration de contraintes se produit du coté proche de la trappe. De plus, les tassements de surface dépendent eux aussi de l’angle d’inclinaison. En conséquence, les résultats de simulation sont en accord avec les tests en laboratoire, ce qui prouve que la DDA permet d’expliquer des comportements mécaniques du tunnel tels que l’arcage, les distributions assymmétiques de pression du sol sur la trappe, ainsi que le profil du tassement de surface dans la masse de roches jointes. Dieser Beitrag beschreibt eine numerische Studie über Tunnel im geklüftetem Fels. Das Verhalten und die Druckverteilungen in den unterschiedlich geneigten und geklüfteten Felsenmassen wird mit Hilfe des Discontinuous Deformation Analysis Programms (DDA) simuliert, und mit Laborversuchen verglichen. Die Resultate bestätigen, dass DDA der Gewölbewirkung im „Trapdoor“ Experiment gut reproduzieren kann. Die Form des Gewölbes, ändert sich mit unterschiedlichen Neigungswinkeln der Schichten. Bei geneigten Schichten entstehen unsymmetrische Druckverteilungen. Auch die Oberflächenabsenkung ist von dem Neigungswinkel abhängig. Die gute Übereinstimmung der Simulationen mit den Laborversuchen zeigt, dass die DDA-Methode gut geeignet ist, um das mechanische Verhalten von Tunneln, wie z.B. den Effekt der Gewölbewirkung, die unsymmetrischen Druckverteilungen bei geneigten Schichten, oder die Oberflächenabsenkung in geklüfteten Felsenmassen, zu erklären.

Jan 1, 2003

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

By William R. Yernberg

Most citizens take it for granted, but minerals produced in the mines of the western United States, including Colorado, are crucial to nation’s standard of living and quality of life, said Colorado’s Gov. Bill Owens in his welcoming remarks at the 106th National Western Mining Conference. The conference, which was organized by the Colorado Mining Association (CMA), was held Feb. 4-6, 2004, in Denver. Attendance was425, up substantially from last year’s meeting. The meeting included the CMA annual membership meeting as well as the CMA chairman’s and president’s reports. The meeting also included awards presentations in which companies were recognized for their efforts in pollution prevention, health and safety, and reclamation. The conference also included a tradeshow.

Jan 1, 2004

By Chris Brown

"The Island Copper plant was designed and built by Fluor Utah Ltd, in conjunction with Utah design staff, Originally designed to treat 33,000 tons/day (t/d) of ore, the current average milling capability is 38,000 t/d (Nov'74). The first of six semi-autogenous grinding lines was brought on line in October 1971, startup of the remainder being governed by equipment delivery schedules.The summer of 1973 saw the start-up of an additional three ball mills, and attainment of the present production level. The current process flowsheet is shown in simplified form.CRUSHINGThe crushing circuit is relatively simple, comprising single stage crushing of the ore followed by screening to fine and coarse fractions.The crusher is a 54 x 74in. Allis Chalmers Superior Gyratory with a setting of 9-lOin., driven by a 500-hp motor. Trucks dump on three sides of a rectangular dump pocket. An 84in. x 20ft. link belt apron feeder draws crushed ore from a 250-ton surge bin below the crusher, discharging onto a 72in. wide inclined steel cord conveyor belt. A fixed splitter box at the conveyor discharge separates feed to two parallel Jeffreys 6 x 20ft. vibrating grizzlies for screening into +4in. and -4in. fractions. The fractions are collected on short reversible conveyors which feed the coarse and fine ore stacker conveyors. Trippers distribute ore to outside stockpiles adjacent to, and above, the concentrator grinding 'floor."

Jan 1, 1975

By M. B. McClenaghan

"This paper summarizes diamond exploration techniques used in glaciated terrain, focussing on indicator mineral and geochemical methods applied to glacial sediments. Understanding the ice flow history, depositional history, and stratigraphy of glacial sediments is essential to successful sampling, interpretation and follow-up of indicator mineral and geochemical anomalies related to kimberlites. Kimberlite indicator minerals survive glacial transport over long distances and the relative abundance of each mineral in till is a function of the primary mineralogy of individual kimberlites. Indicator mineral distributions observed at a regional scale define the net effect of glacial dispersal, often along different ice flow directions. Local-scale distributions define individual dispersal trains. The medium sand (0.25 mm to 0.5 mm) fraction of heavy mineral concentrates, * GSC Contribution No. 2002028 prepared from glacial sediment samples, is best suited for indicator mineral surveys. The application of till geochemistry to diamond exploration is increasing because it is significantly cheaper than indicator mineral analysis and it can be performed quickly. The <0.063 mm (silt+clay) and 0.5 mm to 2.0 mm (coarse sand) fractions provide the best geochemical contrast between background and kimberlite-rich till. Kimberlite pathfinder elements that provide good contrast include Ni, Cr, Ba, Co, Sr, Rb, Nb, Mg, Ta, Ca, Fe, K, Ti and LREE, the relative importance of which will depend on kimberlite composition and that of the surrounding bedrock.IntroductionIn Canada, glacial erosion is the principal means by which kimberlite and its associated minerals have been dispersed, from a few tens of metres to tens of kilometres down-ice. Post-glacial weathering has had little impact on kimberlite debris in the glacial sediments, thus boulder tracing, indicator mineral methods and trace element geochemistry of the fine fraction of till (“drift prospecting” methods) can be used to detect kimberlite dispersal within areas covered by glacial sediment. This paper provides a summary of drift prospecting methods for kimberlite exploration in glaciated terrain, and includes examples of reconnaissance- , regional- and local-scale kimberlite indicator mineral and till geochemical distribution patterns.Weathered kimberlite is more susceptible to glacial erosion than the surrounding bedrock, thus many kimberlites in glaciated terrain are found in low or swampy ground, under small lakes, or covered by thin (< 1 m) to thick (>50 m) glacial sediments. Glacial erosion has removed varying amounts of the pre-glacially weathered kimberlite and, in some cases, the hard competent kimberlite below. For example, glacial erosion of the Peddie, McLean and Seed kimberlites near Lake Timiskaming, Ontario, removed pre-glacially weathered kimberlite, leaving a polished striated subcropping surface (McClenaghan et al., 1999a). In contrast, glacial erosion of the B30 kimberlite, near Kirkland Lake, Ontario (Fig.1), was much less vigorous and left a >10 m cap of soft and highly weathered dark green clay-rich kimberlite (McClenaghan et al., 1996). The thickness of remaining pre-glacially weathered kimberlite will influence the geophysical signature of the kimberlite."

Jan 1, 2002

By R. E. Jones

"Crusher sizing and application in mining operations is the selection of a crusher or a series of crushers to reduce run of mine ore to a size suitable for either autogenous or conventional grinding. It is important that the crusher or crushers be sized to operate within the range to which they have been designed. By the range to which they have been designed, we mean that the reduction ration must be held between specified limits. Reduction ration is the relationship between feed size to product size.In todays plants reduction is usually accomplished in three stages by primary, secondary and tertiary crushers.Primary crushers are either jaw or gyratory and are designed to handle run of mine feed at an open side setting of 5-1/2” to 7”. Reduction ration should not exceed 7 to 1.Jaw CrushersThe model size of a jaw crusher signifies the feed opening. A model 60 x48 jaw has a feed opening 60” wide by 48” long. The 48” is the dimension between the top of the swing jaw and the top of the stationary jaw. The 60” is the width between the two side frames. The crusher open side setting is the discharge opening at the bottom of the crushing chamber with the jaws in an open position. When corrugated jaw plates are used, the open side setting is measured from tip of one jaw plate to the valley of the opposite jaw plate. If a jaw crusher has a 6” open side setting with a 1” jaw motion, you could also say it has a 5” closed side setting."

Jan 1, 1974

Jan 1, 1967

Direct reduced iron (DRI), produced by the reaction between iron ore and reducing gasses, is used as a source of low-residual iron, in addition to ferrous scrap and pig iron, in the production of steel mainly through the electric arc furnace (EAF) route of steelmaking. The main DRI technologies in use are those of Midrex and Hyl, but in recent years a myriad of newer processes emerged based on variations in feedstock, reducing agent and fuel sources. Since the beginning of the nineties, DRI has increasingly emerged as a cheaper, low-residual iron feedstock for EAFs, which have traditionally relied almost entirely on ferrous scrap feed. The main stimulus behind the interest in DRI has been the increasing popularity of the EAF and the ?mini-mill? set-up as the favoured steelmaking option compared to the traditional and much less flexible blast furnace/ basic oxygen converter. This, however, has been creating a problem with regard to availability of low-residual scrap, resulting in upward pressure on high quality scrap prices and leaving DRI, traditionally the ?expensive alternative?, as a much more competitive consideration. The second main determinant has been the increasing production efficiency of existing steel plants which, in the light of improvements such as continuous casting and near net shape casting, has been constraining the supply of low-residual domestic scrap, traditionally the prime source of EAF feed. The explosion of current and proposed DRI projects has been accentuating the mounting interest of global role-players in assuring the availability of reliable sources of low-residual iron units for the future, especially in cases where definitive competitive advantages exist with regard to proximity to primary sources of iron ore and fuel (gas or coal).

Jan 1, 1999

In September, a fleet of 363-t (400-st) Liebherr trucks became operational in Brazil and have already begun moving iron ore in Para state. Prior to the arrival of the the trucks the Brazilian fleet relied on trucks up to 218 t (240 st). With the addition of the 363 t (400 st) trucks, the fleet has since experienced the high productivity offered by Liebherr T 282 B trucks.

Jan 1, 2010

By Yasuo Ojima

A new copper continuous converting process was investigated to evaluate the possibility of its application in the commercial operation. The tests were performed both in the laboratory and in pilot plant scale. Bath smelting process with the use of the top submerged lance technology was applied in these tests. Furnace shape was modified to a lengthwise eylindrical one with a settling area. The furnace monitor was put in the settling area to check the furnace from inside, FeOx-Si02, FeOx-CaO and FeOx-CaO-Si02 based slag systems were used to check their efficiency, The optimum slag chemistry to have good metallurgical results was discussed and FeOx-CaO system with some Si02 content turned out to be preferable although it has not been practically used, In this pilot plant test feeding rate of I tIH of solid grain matte was charged consecutively for two weeks and continuous converting could be done successively. This process is expected to overcome the problems of existing processes and be easily applied in existing plants.

Jan 1, 2003

By R M. Briggs

Kapowai Caldera Complex (KCC), located 10 km west of Tairua (eastern Coromandel Peninsula), is a late Miocene composite collapse caldera, formed during eruption of several small and large volume andesitic rhyolitic ignimbrites. Numerous epithermal Au-Ag mineral deposits and associated alteration zones at the KCC are related to caldera (rhyolite lava domes, intracaldera faults) or regional structures (faults). The main epithermal deposit exposed in the central KCC is associated with an E-W striking structural boundary fault that cuts the Welcome Jack rhyolite dome. Propylitic (calcite - chlorite) and sericitic (quartz - sericite) alteration haloes surround this deposit. Sporadic zones of sericitic alteration are also exposed within and on the margins of the Bulls Run rhyolite dome complex. Epithermal systems post-dated emplacement of these rhyolite domes, but were controlled by them. Propylitic alteration of ignimbrite in the floor of the Kapowai and Kauaeranga valleys is related to the major NE-trending Kapowai Fault which extends SW to south of Thames. Alteration along this fault pre-dates alteration associated with the rhyolite lava domes. Numerous sericitic and propylitic altered welded ignimbrite, rhyolite and andesite lava lithic fragments have been sampled from intracaldera ignimbrites, and although no direct source is known, they infer the presence of buried epithermal systems. Repeated epithermal activity at the KCC is inferred by the exposed epithermal deposits/alteration zones and the older buried geothermal systems. Silicic caldera volcanoes are considered to be critical volcanic environments for epithermal Au-Ag mineralisation in Coromandel, but are highly variable and need detailed stratigraphic, structural, petrologic, and geophysical studies to characterise them.

Jan 1, 1999

By Silas C. Nichols

"Abstract Piling and deep foundations are a staple for transportation projects in the United States (US). Driven or bored piles have been used for everything from support of bridge foundations and retaining structures to support of culverts and embankments on soft ground. Deep foundations have been popular in the US transportation market to better handle large axial and lateral loads, extreme event loading, and to better control structure movement. However, there are challenges in the maintenance of design and construction codes in transportation for consistent and reliable structure foundation elements. A significant amount of effort continues in the US to maintain national codes and specifications at a level consistent with the state of practice, and identify and conduct research for providing safe and cost effective highway structures.IntroductionThe transportation sector in the United States has a hierarchy of design and construction codes that are used for the specification of piling and deep foundations. Any highway or bridge project on the National Highway System (NHS) must be designed and constructed in accordance with a national set of standards approved by the State Highway Departments, and that are acceptable to the Federal Highway Administration (FHWA). However, in any jurisdiction, exceptions are permitted with approval. Therefore, design may be governed by the national standard specification, a state standard specification and design manuals, special provisions, or guideline specifications. Any of these standards, or a combination, may be used depending on the needs of the owner agency.The FHWA and the American Association of Highway and Transportation Officials (AASHTO) have worked together in the development and maintenance of geotechnical design and construction guidance and codes that support the surface transportation community. General geotechnical engineering practice in the United States lacks a singular, national design and construction code that addresses all aspects of geotechnical engineering. As a result, the AASHTO specifications provide the most complete geotechnical specifications focusing on structure foundations, retaining walls, and buried structures for surface transportation applications. This includes piling and deep foundation types commonly used for support of bridges and transportation structures.The FHWA National Geotechnical Team has published several technical guidance documents that include guideline specifications for the design and construction of driven and bored deep foundations. Reference documents published by FHWA summarize the state of practice and provide recommended design and construction guidance. These reference documents have long served as a basis for provisions included in the AASHTO specifications. Maintenance of the design code and specification, and related guidance documents for consistent use on US transportation projects requires a collaborative effort between industry, FHWA, and the member state highway departments that make up AASHTO."

Jan 1, 2014

By M L. van Kampen

The recent (2005) amendments to the Resource Management Act 1991 have made it clear that there is no obligation on an applicant to consult. However the importance and value in consulting with the community, particularly before commencing a major project, cannot be understated. &nbsp; This paper looks at the provisions of the Resource Management Act as they relate to consultation and public participation in the process, and will discuss the benefits of consultation both before an application is filed and following the filing of the application. Engaging with the local community can help shape a project to better fit the community, engender support and address opposition. In short, taking the extra step to what is legally required, can help smooth what is potentially a bumpy road. Examples in practice of the value of consultation are given.

Jan 1, 2006

A series of in situ pull tests has been conducted to determine the holding capacity of the standard SS46 Split Set Stabilisers. The experiments have been conducted in a wide range of geological conditions ranging from bedded rock to blocky ground. The results presented in this paper indicate that cement grouted split sets bolts are likely to provide up to three times the initial bond strength per metre of embedment length provided by the ungrouted bolts. The increased load transfer capacity of the grouted bolts provides an alternative for permanent excavation support using split set stabilisers.

Jan 1, 1997

By S. P. Singh

"The geological features of a rock mass have a direct influence on its blasting characteristics. It has been observed that perimeter control techniques provide excellent results in massive crystalline formations but may give poor results in weak and or highly jointed formations.A field study was conducted with the objective of understanding the role played by the geological features of a rock mass in producing and controlling blast damage. The field work involved the assessment of blast damage at several operating mines and the blasting of drift rounds in a geologically dominant rock mass.The effect of rock strength, rock quality designation (RQD), joint parameters and hydrogeological conditions on blast damage is described below. The influence of number and thickness of weak layers on blast damage is also discussed below on the basis of quantitative data. In addition, critical particle velocity ranges for damage to different rock types have also been outlined in this paper."

Jan 1, 2001