Search Documents

By J. V. Simmons

Composite rock mass failures involve intact rock material as well as fracture and shear on existing defects. Experiences from open-cut coalmining in the Bowen Basin of central Queensland are that failures of this nature occur suddenly with little warning, and are much more common than classical structurally controlled failures. Geological conditions and mining practices in the Bowen Basin are described. The circumstances of a sample of composite failures are described in detail in the paper. From this experience it appears that several aspects of conventional geotechnical investigation and design practice have not contributed significantly to either predicting or controlling the risks associated with sudden failures. These practices are described as myths for reasons outlined in the paper. On the other hand, the reality seems to be that high initial stresses and stress changes caused by excavation lead by a process of extensional deformation to a critical stress condition within the rock mass, and that sudden collapse follows when that critical stress condition can no longer be sustained. It is concluded that learnings gained from underground excavations in rock may be more applicable to open pit excavations than previously thought, and that the processes of prefailure deformation require more careful study if we are to develop more reliable risk management controls.

Jan 1, 2006

By M. Kanefsky

Two channel polarity coincidence and polarity difference statistics are analyzed. The signal, common to both channels, consists of sinusoidal bursts where the exact frequency of the signal is nearly known, but other parameters such as amplitude, phase, and pulse starting time are unknown. The noise inputs are dependent, narrow band, Markov processes. It is shown that the performance depends not only on the signal uncertainties, but on the precise shape of the cross-correlation functions between the noise in-puts. By using two polairty difference statistics in addition to the polarity coincidence statistic, it is shown that the decrease in performance, as well as the cost of hard limiting due to correlated inputs, can be made small.

Jan 1, 1981

By E. V. Lilford

Equity investors and project sponsors have divergent views about expected or minimum returns that should be generated by a mineral project. Irrespective of their views, the fundamental estimation of the corporate cost of capital remains singularly determinable, with additive components of risk and uncertainty often incorporated in the final analysis. This paper discusses and details the fundamental, numerical determination of the corporate cost of capital.

Jan 1, 2006

By M. J. Virnig, B. D. Boley, G. A. Wolfe, J. M. W. Mackenzie

A flowsheet for the recovery of nickel and cobalt from laterite ores has been developed which involves acid leaching followed by hydroxide precipitation of the metal values and then releaching of the hydroxide cake with ammonia. Investigations of the chemistry of extraction of nickel by LIX® 84-I and a developmental reagent, XI-84-IT, along with the physical properties of the organic phases are described. Based on these investigations, suggestions with regard to design of a solvent extraction plant and operating conditions are made.

Jan 1, 1999

Determination of Porosity and its Influence on Specific Surface

Sep 13, 2010

By N. Ogbonna

A mathematical model for bioleaching at the agglomerate scale is developed. The agglomerate is defined as a unit volume of a heap which contains a solid phase (a size distribution of ore particles), a liquid phase (stagnant and flowing leaching solution) and a gas phase (flowing air and air pockets). Leaching at the level of an ore particle is modelled using a diffusion-reaction equation, and oxidation by attached and detached microbes is treated separately. With the aid of the mathematical model, the effect of particle size distribution on the bioleaching of an ore containing a mixture of chalcocite and pyrite, and a culture of iron oxidizers, is investigated.

Jan 1, 2006

By I Sherrell, R Jain, P Jansson

With the depleting iron reserves and difficult market conditions, precision in separation efficiency is of utmost importance. Classical local control options are predominant in the industry, but their inability to adjust to resolve application problems of interest has furthered the need of developing and implementing continuous control methodologies.This paper highlights the recent development in control of Outotec SLon® vertically pulsating high gradient magnetic separator (VPHGMS) including programmable logic controllers (PLC) coupled with distributed control system (DCS), on-site human–machine interface (HMI) control panel, advanced process control, continuous online sampling using Courier® 8 and additional modernisation packages including level control and cooling monitoring. These modern control options result in improved efficiencies, promote safer operation and at the same time reduce operational manpower needs.CITATION:Jain, R, Sherrell, I and Jansson, P, 2017. Automation for efficient separation with the Outotec SLon® vertically pulsating high gradient magnetic separator, in Proceedings Iron Ore 2017, pp 211–214 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By L. P. Lamprecht

Traditionally, South African shaft sinking operations have used electric detonators for the initiation of blastholes. Globally, the trend in shaft sinking is to use the shock tube and detonating cord (STDC) initiation system, with value adding benefits. In pursuing this global trend, Cementation Mining of South Africa in partnership with SMX have ventured the STDC route. This paper explores the work carried out to date, and identifies a number of benefits to be gained by using the system.

Jan 1, 1999

By Ping Yang, Tian-bin Li, Min-hui Wu

"The process of filtrate loss of low solid-phase drilling fluid at different content of polyanionic cellulose is investigated by the standard filtration test. The test results showed that when time of filtration is same, the filtrate volume decreases linearly with the increase of content of polyanionic cellulose. When content of polyanionic cellulose is same, the velocity of filter loss decreases nonlinearly with the increase of time and the velocity of filter loss will reach a stable value. The filtrate volume in 7 to 8 minutes can reach half of the total filtrate volume. At the same time, the velocity of filter loss of drilling fluid decreases nonlinearly with the increase of viscosity. When apparent viscosity is between 3.5~4.15 mPa.s, decrease speed of velocity of filter loss is quick. The results are helpful for characteristics evaluation of filtrate loss of drilling fluid and control of filtrate loss.IntroductionDuring the process of drilling, water of drilling fluid can leakage into stratum, the water can result in instability and collapse of borehole wall. At the same time, the original ratio of drilling fluid will change. The density of drilling fluid will increase, the performance of the drilling fluid will change. Controlling amount of filtration is important to drill successfully. The additives of controlling filtrate loss are mainly two types, particle materials and polymer materials. High-molecular polymer is a kind of high-molecular material, has the adsorption effect, high polymer protection, can improve the advantages of slurry viscosity (Xu,2004 and Dehghanpour,2001). Some scholars carried out some study on the polymer material fluid loss agent in recent years, these study mainly focused on CMC, HEC, MHEC, CMHEC, starch and its derivatives(Zhang,2005 and Chevron,2009).About PAC (polyanionic cellulose) as drilling mud additives, a few of scholars carried out some relevant work. Plank (1992) applied PAC into ordinary freshwater drilling fluid and analyzed temperature stability of freshwater drilling fluid. Bennion (2000) applied PAC into drilling fluid and analyzed effect of polyanionic cellulose on strata inhibitory. Huang (2011) analyzed effect of PAC on properties of the high-density water-based drilling fluid. Mahto (2004) applied PAC into fresh water and salt-water drilling fluid and analyzed effect of PAC on rheological properties of the drilling fluid. Wang (2008) applied PAC into alkaline drilling fluid to study various performance of drilling fluid. PAC is a renewable resource and has good application prospect (Ankara, 2005). So it is very important to understand the effect of PAC on filtration process of drilling fluid.The test was conducted by changing the content of the PAC in drilling fluid. The object of this paper is to understand effect of polyanionic cellulose on filtration process of the low solid-phase drilling fluid."

Jan 1, 2017

By Carl Hendricks, Malcolm Scoble

There currently exists no viable means of obtaining continuous feedback on blast efficiency. This paper describes the adaptation of a loading shovel to serve as a diagnostic tool to evaluate the success of ground preparation. Work undertaken in a large western Canadian open pit involved microprocessor-based instrumentation for the performance monitoring of an electric mining shovel. The monitored shovel responses proved to be reliable indicators of variations in muckpile diggability. This approach is considered to provide a very comprehensive survey of post blast conditions since such a shovel interacts which every cubic yard of a blast.

Jan 1, 1990

Mineralisation was identified at Gladstone Hill as far back as the late 1870's û early 1880's, shortly after the initial discovery of Martha Hill. Indeed, early recovery problems from the Martha Hill mineralisation led to the preferred development of are bodies within what is now the Union Hill Joint Venture tenement; ore bodies such as Silverton, Amaranth, Union to name a few. Work at Gladstone Hill is carried under the Union Hill Joint Venture, a 50:50 joint venture between Auag Resources Ltd - manager (a fully owned subsidiary of Otter Gold Mines Ltd) and Welcome Gold Mines Ltd (a fully owned subsidiary of the Normandy Group). The joint venture participants also operate the adjacent Martha Hill operation. Mineralisation of Gladstone Hill, as with mineralisation at the adjacent Martha Hill, has been interpreted as a low sulphidation epithermal Ag-Au system hosted within hydrothermally altered andesites of the lower Coromandel Group. Drilling in recent years has successfully identified extensive mineralisation associated with the Gladstone vein set and the more recently identified high grade Moonlight Lode. Veining ranges in character from thin stock works to broader lode-style banded chalcedonic to cherty quartz. Visible gold is rare, with mineralisation generally associated with very fine-grained pyrite, arsenopyrite and minor electrum. The potential for the Gladstone Hill area is yet to be clearly defined as drilling to date has yet to close off mineralisation both along strike and down dip. If further drilling is successful, the joint venture partners believe Gladstone Hill could contribute significantly to the economic future of current operations.

Jan 1, 1999

By E. Northcott, I. M. LeBaron

Before describing the electrostatic processing of feldspar, it might be well to review some of the basic definitions and terminology of feldspars. The feldspar minerals constitute a group of alumino-silicates of potassium, sodium, and calcium. Barium feldspar sometimes occurs naturally but is very rare. Hardness varies between 6 and 6.5 and specific gravity between 2.5 and 2.8. Color is generally white or pale shades of red, yellow, or green. The approximate chemical composition of the principal feldspars is given in Table I. The albite (sodium aluminum silicate) and an-

Jan 1, 1959

Investigation of the Effect of N-Substituents on Performance of Thioureas as Special Collectors for Copper Sulfides by ab Initio Calculations

Sep 13, 2010

By M. W. Barger, J. K. H. Ma, J. Y. C. Ma, V. Castronova

The objective of this study was to investigate the effects of various bisbenzylisoquinoline (BBIQ) alkaloids on respiratory burst activity of alveolar macrophages and to characterize the interaction of these drugs with alveolar phagocytes. BBIQ alkaloids were chosen for study because they exhibit a wide range of antifibrotic potencies in a rat model, with tetrandrine being very effective and tubocurarine being ineffective. These drugs inhibited zymosan-stimulated oxygen consumption with a potency sequence of tetrandrine (IT) = fangchinoline (FA) > berbamine (BE) ., cepharanthine (CE) "" cycleanine (CY} ~ tubocurarine (TU). This inhibition of respiratory burst activity could not be attributed to a drug-induced decline in the ATP content of these pneumocytes. Drug binding to alveolar macrophages was directly dependent on temperature and drug concentration. The sequence for binding capacity was FA > TT = BE = CY > CE ~ TU. Therefore, there was no simple relationship between binding capacity and inhibitory potency. Binding capacity was not related to lipophilicity of these alkaloids. In addition, tetrandrine failed to bind to metabolically dead cells or sonicated macrophage preparations. These data suggest that the interaction of BBIQ alkaloids with phagocytes is not simply nonspecific binding to membrane lipids. Alteration of the cytoskeletal system with vinblastine, taxol, or cytochalasin B decreased tetrandrine binding by approximately 33% when adtkd separately and by 93% when added jointly. Pre-exposure of alveolar macrophages to stimulants increased the ability of BBIQ alkaloids to inhibit both oxygen consumption and superoxide release. These data suggest that the mechanism by which BBIQ alkaloids inhibit activation of phagocytes involves microtubules and bules and microfilaments. Pre-exposure of macrophages to stimulants would change the conformation of cytoskeletal components and may make these structures more susceptible to drug interaction.

Mar 1, 1992

Mining companies in order to compete and succeed in being viable business propositions must look to the future and select mining methods which guarantee improved efficiency and productivity as well as lower costs. A mining company in adopting a method of mining must now select the equipment most compatible. To some mines compatible equipment may mean the use of drilling jumbos to replace hand held rock drills or the use of load haul dump units to replace scrapers. To other more mechanised mines compatible equipment may mean the use of raise borers and road heading machines. The right decision will be where equipment compliments method in such a way that the working environment is improved, productivity is maximised, cost if reduced and all profit opportunities are optimised. An example of such is where the use of improved mining techniques in underground operations may see cut off grades reduced. By selectively mining these lower grade orebodies, smaller operation's ore reserves improve and the capacity for continued growth is enhanced.

Jan 1, 1990

By R. G. B. Pickering

Over the last few years Lonmin Platinum and Sandvik have embarked on a unique partnership of collaboration through a systematic approach to developing equipment to mechanize and automate narrow reef platinum mining. After the initial design and manufacture of the equipment the key aspect is the integrating equipment, people and method into a mining system. Another key aspect of mechanization is the optimization of equipment utilization, and this philosophy has ensured continual evolvement of mining methods. This paper describes the trials and development that have resulted in the mining method described as Lonmin mechanized breast.

Jan 1, 2007

By S. Escoffier, A. Giraud, K. Su, F. Homand, N. Hoteit

Abstract For the feasibility study of an underground waste disposal the characterization of the coupled behaviour of the host rock is required: Because of the very low permeability of these formations few experimental data are generally available. In this framework the uses of the sensitivity studies could orient the experimental efforts by highlighting the key parameters of the formation. This paper gives a first approach of the sensitivity studies performed with probabilistic methods in the geomechanical field. A one dimensional model which characterizes the thermohydromechanical response of an argillaceous rock to the excavation of a waste canister site and its setting up, is considered. Zusammenfassun Die Machbarkeitsstudie eines tiefliegenden Endlagers für radioaktive Abfälle beinhaltet die Untersuchung des gekoppelten Verhaltens des im Lagerbereich anstehenden Gesteins. Aufgrund der sehr geringen Wasserdurchlässigkeit dieser Formationen liegen häufig nur wenige experimentelle Angaben vor. Die Verwendung von Sensibilitätsstudien kann in diesem Zusammenhang als Hilfsmittel zur Entscheidungsfindung dienen. Dabei sollen die maßgeblichen Eigenschaften der Formation festgestellt werden, anhand derer der Umfang der experimentellen Erkundung festgelegt werden kann. Dieser Artikel stellt einen ersten Ansatz zur Durchführung von Sensibilitätsstudien mittels einer mechanisch-probablistischen Kopplung im Bereich der Geomechanik sowie die Vorteile gegenüber Parameterstudien vor. Zur Abbildung des thermohydromechanischen Stoffverhaltens von tonigem Fels während der Schachterstellung und der Einlagerung der Abfälle wird ein eindimensionales Model verwendet. Résumé L'étude de faisabilité d'un centre de stockage de déchets radioactifs en profondeur passe par la caractérisation du comportement couplé de la roche hôte. Du fait de la très faible perméabilité de ces formations, souvent peu de données expérimentales sont disponibles. Dans ce cadre l'utilisation d'études de sensibilité permettrait d'orienter les efforts expérimentaux en faisant ressortir les caractéristiques primordiales de la formation. Cet article présente une première approche de la réalisation d'études de sensibilités à l'aide de couplages mécano-fiabilistes dans le domaine de la géomécanique. Un model unidimensionnel caractérisant la réponse thermohydromécanique d'une roche argileuse au creusement d'un puit de stockage et à la mise en place de conteneurs de déchets est considéré.

Jan 1, 2003

By R. H. Grau, R. Krog

The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of large-opening mines. The research has demonstrated that the ventilation of large-opening mines improves significantly by including ventilation requirements in the mine planning process and implementing somepractical techniques during mining. Planning the location of long pillars to reduce the number of crosscuts between intake airways and return airways, positioning auxiliary fans in their proper locations, and establishing ventilation stoppings with minimal leakage all significantly improve the ventilation of large-opening mines. Mine operators that adopt these techniques in the mine ventilation plan will reduce mineworkers’ exposure to airborne contaminants.

By M. Kumral

Raw material fed into a processing or refining plant is required to be uniform in composition for several reasons. When the mined ore is highly variable in quality the only way to ensure consistency is to homogenize the ore prior to the process. The problem is more complicated in the case of multiple ore sources. The idea behind the research is that theoretical blending ratios can serve not only to meet predefined specific criteria but also to reduce grade fluctuations of variables under consideration. In this paper, the problem is formulated as a quadratic programming problem, whose objective function is in quadratic form and constraints are linear. A case study was conducted on a data set from an iron orebody to demonstrate the technique. The objective was to minimize the blend variability in terms of each variable (in this study, iron, silica, alumina and lime) grade of ores extracted in three different production faces. The stockpile capacity, lower and upper limits of each variable satisfying operational requirements and non-negativity were constrained to the model. A modified simplex method developed by Wolfe was used for solving the blending and homogenization problem. The promising results can be used as apart of the stacking and reclaiming design. Keywords: blending and homogenization problem, quadratic programming, Wolfe method.

Jan 1, 2005

By M. Ge

Pattison Mine is a small sandstone mine located in Iowa. The sandstones produced by the mine are not common construction and aggregate materials. The stones are used to produce a special type of sand for hydraulic fracturing, a critical technique for recovering tight gas and shale gas. These sandstones are very different from the minerals and rocks which have been studied extensively in mining. On the one hand, they are brittle as characterized by an unusually high friction angle, up to 69°, and steeply curved failure envelopes. On the other hand, they are friable, possessing extremely low, and in most cases zero cohesion. The scarcity of the ground control techniques for this particular mining environment has created many difficulties for the mine operators. In order to resolve these problems, a research program was set up by the mine and Missouri University of Science and Technology. This paper discusses the preliminary results of this investigation.

Jan 1, 2012