Search Documents

By David A. Bacca

Hydraulically powered submersible borehole dewatering pumps and emulsion/ANFO blends evolved at about the same time and for the same reasons. Mining operators needed safe, efficient dewatering systems and water resistant products.

Jan 1, 1994

By Deborah McCombe

-Canadian Regulators -Qualified Person -Professional Association -Resources & Reserves -Foreign Codes -Disclosure of Historical Resources -Issues in Application of Resources & Reserves -Industry Best Practices developed by CIM -Technical Report and Reserves and Resources -Summary

Jan 1, 2003

By D A. Manhire, R M. Flores

The commercial develop of coalbed methane from the Powder River Basin has demonstrated that low-rank coals can be a viable source of gas. Currently over 20 000 coalbed methane wells exist in the Powder River and it is predicted that there will be 50 000 wells by 2010. What makes the Powder River Basin successful is the thickness of the coal (in excess of 30m) as well as the low ash content (

Jan 1, 2002

By O. MacIntosh

The Round Mountain gold mine, located 90 km (55 miles) north of Tonopah, NV began large-scale production in 1977. During 2008 Round Mountain Gold Corp. (RMGC) relocated the primary crusher facility approximately 300 m (1,000 ft) to make room for the next phase of openpit mining activities. This facility was installed in 1988 and used a log-crib retaining wall and dump pocket. RMGC selected Hilfiker Retaining Walls and Collins Engineers, Inc. to provide design and materials for a new 17-m- (56-ft-) high mechanically-stabilized embankment (MSE) wall to support the haul trucks at the new location. The construction contractor was EarthTech West Ltd. of Norwood, CO. An MSE wall with a cast-in-place concrete face was chosen as a durable, yet less expensive alternative to the reinforced concrete dump pocket that was originally designed for the project. The arrangement of the MSE wall is of an unusual configuration to meet a variety of operational and maintenance requirements. This paper outlines the selection process, design and construction of the MSE wall.

Jan 1, 2010

Crystalline silica is the scientific name for a group of minerals composed of silicon and oxygen. The term crystalline refers to the fact that the oxygen and silicon atoms are arranged in a three-dimensional repeating pattern. This group of minerals has shaped human history since the beginning of civilization. From the sand used for making glass to the piezoelectric quartz crystals used in advanced communication systems, crystalline silica has been a part of our technological development. Crystalline silica's pervasiveness in our technology is matched only by its abundance in nature. It's found in samples from every geologic era and from every location around the globe. Scientists have known for decades that prolonged and excessive exposure to crystalline silica dust in mining environments can cause silicosis, a noncancerous lung disease. During the 1980's, studies were conducted that suggested that crystalline silica also was a carcinogen. As a result of these findings, crystalline silica has been regulated under the Occupational Safety and Health Administration's (OSHA) Hazard Communication Standard (HCS). Under HCS, OSHA regulated businesses that use materials containing 0.1 or more crystalline silica must follow Federal guidelines concerning hazard communication and worker training. Although the HCS does not require that samples be analyzed for crystalline silica, mineral suppliers or OSHA-regulated businesses may choose to do so if they wish to show that they are exempt from the requirements of HCS. Because crystalline silica is an extremely common mineral and the HCS will affect many mineral commodities, it is important then, that there be as clear an understanding as possible of what is and what is not crystalline silica, and where it is found and used, and how it is qualitatively and quantitatively identified. This primer is an attempt to accomplish this in as nontechnical a manner as possible. This primer will examine crystalline silica. Part I will describe, in nonscientific terms, what crystalline silica is and how we come in contact with it. Part" will discuss the regulatory decisions that have created new interest in this ancient and widespread substance and will present a nontechnical overview of the techniques used to measure crystalline silica. Because this primer is meant to be a starting point for anyone interested in learning more about crystalline silica, a list of selected readings and other resources is included. The detailed glossary, which defines many terms that are beyond the scope of this publication, is designed to help the reader move from this presentation to a more technical one, the inevitable next step.

Jan 1, 1992

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

By Jack Kadlecik

This final technical report describes the concept feasibility study, testing, design and development effort which went into. The quick opening enclosure access cover and flame path tolerance checking system. A detailed definition of the explosion-proof multiple start threads is shown for two (2) sized electrical enclosures.

Jan 1, 1972

Jan 1, 1963

By D. F. Scott

The purpose of this study was to determine if miners are at risk from exposures to chemicals used in the mining industry, and determine the nature and sources of the illnesses and injuries. The authors reviewed the Mine Safety and Health Administration?s (MSHA) Employment and Accident, Injury, and Illness database and identified 2,705 cases of chemical-related injuries and illnesses that were reported to MSHA from 1999-2006, involving 66 different chemicals. The main source (cause) of chemical-related cases was acids/alkalis (about 39%). The primary nature (effect) of chemical-related cases was chemical burns (about 57%). The job classification where workers incurred the most chemical-related injuries and illnesses was cleaning plant operator/media operator/boney preparation plant operator/crusher worker. The number of nonfatal days lost did not change significantly and overall, the incidence rate of chemical-related cases decreased by 36%. Chemical burns accounted for a large number of injuries; mining companies should carefully examine their personal protective equipment (PPE) requirements, training methods, and safety culture to insure that their workers are protected.

Jan 1, 2009

By Ian Townsend

A prerequisite for good filter performance is that the total filter installation has been well designed. In this sense, the filtration testwork will provide scale-up data, and an insight into the relationship between operating parameters that may then be optimised, and used in the development of a control strategy. A good understanding of the filter’s operating principles will ensure correct selection and sizing of ancillaries, allowing in particular for the difference between instantaneous and average flow rates.

Sep 13, 2001

By E. D. Calvert

The Bureau of Mines, in its effort to promote greater utilization of domestically abundant materials, conducted reasearch on an alternate mold material that has commercial potential for titanium investment casting. Using variations of the conventional lost wax molding process, investment shell molds were formed entirely of fused, calcia-stabilized Zr02 and a Zr02-forming binder. Optimization of binder/slurry properties', stucco grain size and dis¬tribution, and curing practices resulted in a structurally sound investment shell that was distortion free and thermally stable. Small titanium castings, weighing up to 10 pounds, were prepared in unheated molds by both static and centrifugal casting techniques. Microstruc¬tural examination of the castings revealed that mold fill and surface quality were enhanced by centrifugal casting, although good results also were obtained from the statically poured molds. Microstructural and electron microprobe examinations showed that excessive, brittle case formation could be avoided by curing the dried shell molds in air for at least 2 hours at 1,400° C. Increasing curing temperature and time above these levels yielded added bene¬fits. Molds fired in vacuum at 1,500° C for 4 hours yielded castings essen¬tially free of case formation. The tensile properties of as-cast test specimens (no surface conditioning performed) id the chemical composition of representative metal samples showed that castings produced were comparable to Grades C-1 and C-2 unalloyed titanium This indicated that no sifnificant degradation of metal properties resulted from mold/metal interaction.

Jan 1, 1981

By P. T. Slatter

The efficient and accurate design of pipe and pumping plant for non-Newtonian mineral slurries remains a problem. The objective of this paper is to present the development of the Balanced Beam Tube Viscometer (BBTV), an instrument which could facilitate more accurate design for these slurries. The background of rotational and tube viscometry is reviewed and the fundamental principles and inherent advantages of the BBTV are given. The design, data acquisition and processing techniques are introduced and results showing the reliability of the new instrument are presented and discussed. It is concluded that the BBTV is a reliable and versatile instrument for both routine analyses and research work, and has the potential to provide data for the refinement of the design procedure for mineral slurry pipe and plant design.

Jan 1, 1998

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By M. M. Ayoub

This volume is the second of three volumes comprising the final report of the research project "Biomechanics of Low Coal." It covers only the anthropometric study of low coal miners. Volume I summarizes the overall biomechanical, anthropometry, and work physiology study conducted. Development of work clothes modified to meet the needs of low coal miners is described in Volume III. The male and female anthropometry, with the exception of weight and circumferential dimensions, was quite similar to the comparison populations. The miners tended to be heavier and have greater circumferences. The measurements made in this study were used to develop 5th, 50th and 95th percentile, quarter and half scale, male and female mannequins. These twelve mannequins can be used in work place and equipment design and redesign.

Jan 1, 1982

By FRANKM. SEIBERT, G. G. Oberfell, GEORGEA. BURRELL

The Bureau of Mines is conducting a series of investigations with the common aim of minimizing the losses that occur in the mining and treatment of mineral substances. The results of the investi- gations are being published in reports of the bureau. This report treats of a method of preventing some of the waste of the natural gas incidental to oil mining. This method, the condensation of gasoline from natural gas, offers to the oil operator and others a profitable means of utilizing some of the oil-well gas now being wasted. The most desired constituent of crude oil is obtained, the production of oil is not hindered, and the gas, after the extraction of gasoline, can be returned to the leased area to drive pumps or into pipe lines for uses to which natural gas is ordinarily put, usually with its fuel value lessened only in slight degree. Publications already issued briefly discuss the subject. In this report the work is treated in greater detail, and the results of many additional tests are shown.

Jan 1, 1915

By H. K. Lin

The effect of metallic iron fines on froth flotation of a sulfide ore was examined by comparing the flotation results with and without iron fines present in the flotation feed. Mild steel and ceramic laboratory ball mills were used to grind 600 g sulfide ore charges. The mild steel ball mill generated approximately 4.6 g of iron fines (0.8% of the ore charge mass) when grinding to a product size of 80% passing 200 mesh (75 mm). When a low dosage of a weak xanthate collector was used in flotation, the impact of the iron fines on sulfide flotation was marked. Higher dosages of stronger xanthate collectors rendered the impact of the iron fines much less significant. Consumption of the collectors by the powdery iron fines is believed to cause the differences observed in the flotation results. A galvanic effect on flotation was not evident in this study. The impact of the iron fines on silicates depression was also examined.

Jan 1, 2008

By P. Goosen, A. Paterson, E. Paulsen

Ticor South Africa is currently involved in the mining and processing of a heavy mineral oredeposit at Hillendale Mine on the KwaZulu-Natal north coast. The orebody is characterized by a high ultra fine fraction (-45µm) that has a variable rheological behaviour when subjected to shear and hydration. Experience at Hillendale has shown that the ultra fine mineral tailings are sensitive to shear history in terms of shear intensity and shear duration as well as hydration history. This phenomenon expresses itself right through the primary beneficiation process influencing the mineral separation, but is especially prevalent on the residue disposal i.e. slurry transport and deposition on the tailings impoundment. Tube viscometer test work was conducted on the flocculated fine tailings that indicated that there was a change in rheology as a result of shear. This paper presents the results of the on-site test work conducted at the mine to measure the rheology at various stages in the process.

Jan 1, 2003

By R. E. Head

[This paper embodies the data obtained by a detailed statistical, microscopic analysis of the composite mill feed concentrate, and tailing from the Magne and Arthur mills of the Utah Conger Co. for 1 month in 1929. It is one of a series of papers by the same authors5 dealing with the mineralogical characteristics of the ore and concentration products from various well-known plants. The work was done in the cooperateive microscopic service laboratory at Salt Lake and represents the results of cooperation between the United States Bureau u of Mines, the Utah Copper Co. and the University of Utah.]

Jan 1, 1935

By Nancy Estrada, Jane Nowell, Cathy Jennings, Debra Yniguez, Carol Lavery, Kristin Harrer

Pilots of the MH-60S helicopter are exposed to continuous whole body vibration (WBV). Pilot fatigue is a growing operational concern due to the increased frequency of extended durations of missions (6-8+hours) in support of Operations Iraqi Freedom and Enduring Freedom. Endurance aspects of the currently used rotary wing seating systems were not optimized for the longer missions and wide range of pilot anthropometric measurements, which is now typical of naval aviation. The current seating systems were designed primarily to meet crashworthiness requirements, not for the wide range of pilot anthropometry or to mitigate WBV. Albeit, an issue, pilot fatigue and reduced mission effectiveness are also critical concerns. Current Hazard Reports indicated that pain in pilots’ legs and backs begin two to four hours into the flight and increase with time. Mission readiness also decreases with an increase in flight duration due to the constant distraction of pilots shifting in their seats while trying to get comfortable. Froom, et al [2] reported a dose-response relationship between the length of military helicopter flights and back discomfort. He also concluded that this pain is typically dull, over the lower back, and its prevalence and intensity are dependent on the total flight hours of exposure. Methods This study evaluated WBV produced in the pilot seating systems onboard the MH-60S. The purpose of the study was to test and compare the effectiveness of two different seat cushions, the current seat cushion versus an anti-vibration seat cushion. Both seat cushions were measured for acceleration levels averaged over five-minute intervals using a triaxial seat pad accelerometer. The recordings were completed for a 3-hour straight and level flight. A frequency analysis from 0-80 hertz (Hz) was conducted on all acceleration measurements to determine the dominant axis and frequency of the pilots’ vibration exposure. The results were then compared to the applicable Threshold Limit Values (TLVs) established by the American Conference of Governmental Industrial Hygienists (ACGIH) [1] and the International Organization for Standardization (ISO) 2631.1 [3] to determine the MH-60S pilots’ permissible exposure time for both seat cushions. Results The results of the study showed that for both seat cushions the vibration levels of the z-axis at 16 Hz had the shortest allowable exposure duration, according to the ACGIH TLVs. In the z-axis at 16 Hz, the MH-60S’s current seat cushion’s acceleration levels indicated an exposure time limit of approximately 6 hours, while the anti-vibration seat cushion’s acceleration levels pierced the 8-hour exposure time limit curve. This is shown in the graph below.

Jan 6, 2006

By W. R. Paterson, W. Morton, D. B. Cameron

The Massbal II computer simulation program has been used to develop a general framework for the building of thermochemical models of metallurgical processes. The framework allows the rapid, simple construction of complex models of process equipment for use in flowsheet design, planning and plant operation. Application of the program to model the iron-making blast furnace and a flash smelting process is described

Apr 1, 1991