Search Documents

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By Richard Addison

Introduction A staccato beat rings out across the Australian bush. The stamps are at work, slowly pulverizing gold-bearing ore for a patient, grizzled prospector. This is the State Battery near Marvel Loch, a tiny 22.6-t/d (25-stpd) capacity gold plant operated by the Western Australia government. It is one of many such plants located in remote corners of Western Australia and the Northern Territory. They are miniature custom mills operated for the benefit of prospectors and small mine operators. These state batteries are so called because they are operated by state governments and because the principal item of machinery in the plants are stamp batteries. They are fascinating anachronisms - throwbacks to times past, a century ago, to the hard and heady existence of gold rush days. Marvel Loch plant Typical of these operations, and perhaps a trifle more sophisticated than most, is the plant near Marvel Loch, a small center for mining and farming about 400 km (250 miles) due east of Perth. Marvel Loch. The name evokes visions of a pristine lake set in a cool, green, misty glen of the Scottish highlands. Actually, it is probably a hot, dry salt pan somewhere nearby. Just where the "loch" is difficult to discern. There is no sign of it on the map.

Jan 7, 1986

By D James

Fletcher Challenge Limited through its subsidiary Grampian Mining Co Limited has carried out an ore evaluation of one of New Zealand's largest known deposits of ilmenite located at Barrytown on the West Coast of the South Island, New Zealand. The ilmenite is located in a beach sand environment which has previously been mined for gold. Two analytical techniques were developed to quantify the resource. Considerable difficulty was experienced in this phase of the evaluation due to the presence of major inclusions within the ilmenite grains. Wet and dry concentration circuits, utilising spiral, wet magnet, high tension and plate electrostatic separators have been designed to produce ilmenite from the ore. Studies to utilise the titanium content of the Barrytown ilmenite have been made. Recent work has been directed towards a titanium dioxide pigment process.

Jan 1, 1986

By Michael J. Beus

This Bureau of Mines report describes the development of load cells for measuring compressive loads in timber and lock-bolt support systems commonly used in. coal; metal, and nonmetal mines Design and evaluation is covered in detail to insure a reliable, accurate, and practical instrumentation scheme. The load cells are relatively inexpensive and adaptable to various size support systems. User-oriented procedures are emphasized, and design equations were reduced to a series of nomographs. Laboratory evaluation, destructive testing, environmental testing, and tests to determine the effect of extraneous loads were conducted. Field performance was evaluated in conjunction with ongoing Bureau projects at a metal mine in North Idaho and a coal mine in Utah. Load cells utilizing a titanium alloy as the cell body and weldable strain gages as the strain-sensing components satisfied the basic design and performance criteria, and with minor design modifications, the load cells can be adapted to many mining applications.

Jan 1, 1974

By A. v. E. Conradie, I. Nieuwoudt

Comminution and flotation circuits are frequently perturbed by disturbances, such as feed particle size variations, ore hardness and varying mineral liberation, which can have a significant impact on the recoveries and grades. Although advanced control strategies can neutralize many of these disturbances, few such systems have been implemented at present. One reason is that it is only recently that the requisite sensor systems have been developed and used to control froth flotation systems. Another is owed to the complexity of these non-linear interactive systems. In this paper, a plant-wide control strategy is considered, wherein both unit operations have a single overall control objective. The automated design of the controller is based on an advanced evolutionary algorithm viz., Symbiotic, Memetic Neuro-Evolution (SMNE), for developing neural network controllers in a reinforcement learning framework. A rigorous phenomenological comminution and flotation model was used to develop suitable neurocontrollers, which used all possible sensor inputs and available manipulated variables. The neurocontroller managed to identify optimal or near-optimal operating conditions consistently and showed robust performance in the presence of significant disturbances. The results suggest that evolutionary reinforcement learning offers a very competitive approach towards the development of integrated non-linear controllers for mineral processing plants. Keywords: neural networks, control, flotation, comminution, evolutionary reinforcement learning

Jan 1, 2003

By A. L. Foote

This is the final report of work accomplished during 1973-75 under U. S. Bureau of Mines Contract No. H0242015, "System for Handling Underground Mine Supplies and Materials." The purpose of the contract was to develop a mechanical device which could safely perform handling tasks that are normally done manually in underground bituminous coal mines. The report discusses studies leading to construct-ion of a battery-operated, three-wheel vehicle with a six-degree-of-freedom manipulator. Supportive design studies included collection and analysis of production, manual functions, and injury data on the underground bituminous coal mining industry. Transfer tasks in section storage and working places were the prime candidates for mechanical handling. Functional specifications were developed for two handling devices (one to handle existing unit loads and one to handle repackaged unit loads) and for a vehicle to mount the handling device. Design concepts for nine different handling devices were developed and a cost/benefit evaluation made for each. Detail design, capital and operating costs, and method improvement savings data were developed for two battery-operated vehicles and for two different manipulators. The three-wheel vehicle with anthropomorphic manipulator was chosen for development.

Jan 1, 1978

By Raja V. Ramani

As the new millennium approaches, it is appropriate to assess the progress that has been made in mine health and safety, a matter of concern to management, labor and government. One can hardly look at the major events of the last century — from the birth of the US Bureau of Mines through the enactment of the modern health and safety laws — without realizing that the march has been relentless toward eradication of health and safety threats in mining. The progress is spectacular in mine safety and significant in mine health. In looking at the future, it is safe to assume that societal demands will increase for improved health and safety conditions in the workplace. So will the demands for greater technological leaps. The standards will for measuring success and the expectations of progress in creating a safer and healthier mine environment will grow. The possibilities are enormous of meeting these exacting requirements in the 21st century.

Jan 1, 1999

By S. L. Gay

The conventional mass-balance equations used as constraints can lead to flow estimate values of zero even though the flow estimates should be some positive number. This is because many of the constraint equations are satisfied if the flow rates are zero. The way to overcome the problem is to use a slightly different form of the equations. For example, rather than use the conservation of flow of solids as a constraint it is better to use the constraint that the percentage of solids going into a unit equals the percentage of solids coming out of the unit. Examples are given using mineral processing data sets from Mount Isa, Queensland, and Red Dog, Alaska

Jun 21, 1905

Incorrect sampling and measurement operations and misunderstanding the components of variability can cause huge economic losses to the mining industry. The main objective of this paper is to illustrate by means of four historical facts how Codelco has been evolving in those issues since the late 1980s. The El Abra bias, the awareness of the different kind of sampling errors and the role of Francis Pitard, the awareness of weighting errors, and the understanding of the components of nature and process variability are described. It has been a slow but a consistent process. Much progress has been achieved but still there are many opportunities for improvement to transit from the tonnage culture to the productivity culture.

Jan 1, 2008

By John L. Thames

The benefits of water harvesting as an alternative to conventional reclamation were demonstrated on the Peabody Coal mines in Northeast Arizona. The project produced food crops for four years, and demonstrated that a catchment/crop area ratio of about 2.5:1 was sufficient to obtain sufficient water from the 11 inch annual precipitation to produce garden and fruit varieties in quantities equal to or exceeding national production averages. The economic returns exceeded those of the conventional practice of returning the mine area to rangeland by at least ten fold. Subsidence of the regraded spoil was the only major problem in maintaining the system. Although, water harvesting systems have the potential of providing high economic returns and greater social benefits, as demonstrated by this project they are presently at variance with the strip mining regulation.

Jan 1, 1984

By Mark Sanders

This report describes an experiment which was conducted to compare the relative bumping hazard of a low and high profile hard hat (helmet) in a low seam mining environment. The study was specifically designed to assess the effect of lowering the helmet profile on frequency of head impacts in an underground low seam coal mine simulator. This involved subjects performing four common low coal mining tasks wearing the low and high profile helmets in the low seam simulator (36" and 48? heights). The results of the study indicated that a low profile helmet could reduce bumping frequency in underground low coal approximately 25%, and as much as 80% on selected tasks. It was beyond the scope of the study to measure the impact force, thus it was not possible to estimate the effect of the low profile helmet on severity of impacts underground. The research team recommended that a more extensive investigation be made of head injuries experienced in low seam mining (both underground and surface) with the objective being to assess the impact of a low profile helmet on total head accident exposure.

Jan 1, 1980

By V 9. 0 / 300 dpi

ATHOUGH turquoise mining was, so far as we know, the first large, well-organized mining operation,' gem mining, from the Roman con-quest of Egypt until the opening of the South African pipe diamond mines some 50 years ago, was largely carried on' by individuals 01' small companies in a relatively primitive way. Now" however" gem mining does not yield in efficiency or in scale of operations to the mining of other mineral products. In 1926 the diamond mines of the world milled some 9,000,000 cu. yd. and produced 0,43 cu. yd. diamonds, a remarkable example of concentration. The Premier Diamond Mining Co. up to Oct. 31, 1927, had milled 116,455,550 loads (each of 16 cu. ft.) from which 26,-217,144 carats of diamonds" worth £29,897,971 2s, 9d., were recovered. The Burma Ruby Mines, Ltd., operating sever-al alluvial mines in Burma in 1911-12, mined and milled 1,479,845 truckloads of gemmiferous earth for 15c. per load. We of the industry can there-fore, with good grace, disclose some of the myths and also describe some of the primitive mining methods of the, dark ages of our industry. The methods, so far as I know, were not patented, and if they were, the patents have expired, so that engineers in other branches of the art are free to use them if they see fit.

Jan 1, 1928

By John Mitchell, Mark K. Jorgensen

Newmont Mining’s Ahafo Mine is located in Ghana approximately 300 km (190 miles) northwest of the capital city of Accra in the Brong-Ahafo region. The nearest city is Sunyani, located 45 km (28 miles) to the north. The Ahafo Mine will process ore from seven major pits that extend along a 40-km (25-mile) strike. Four pits are in the south and three pits are in the north. The resource is currently stated at 373 t (12 million oz). But it still has the potential for growth both from new discoveries and the development of underground operations.

Jan 1, 2007

By D. Bienstock

To develop a rugged catalyst capable of withstanding hydraulic attrition resulting from the oil-circulation process for synthesizing liquid fuels, use of an iron catalyst containing an active coating surrounding an inert solid core of metal was investigated. This massive-iron catalyst in the form of steel shot and lathe turnings was activated by partial oxidation with steam at 600° C, impregnated with alkali, and reduced with hydrogen at 450° 6. The massive-iron catalysts were resistant to oxidation and spalling, and a 6-month catalyst life was attained. Higher operating temperatures could be employed than with fused iron oxide catalysts, resulting in greater gasoline yields. Because the lathe turnings pack with void volumes of 70 to 90 percent, it has become possible to employ a fixed bed without the danger of cementation that occurs with fused iron oxides.

Jan 1, 1963

By A. D. Pelton, Y. -B. Kang, S. A. Decterov

Computerized thermodynamic databases for solid and liquid metal, slag and solid oxide phases in the Al2O3-CaO-CoO-CrO-Cr2O3-FeO-Fe2O3-MgO-MnO-NiO-SiO2-S system have been developed by critical evaluation/optimization of all available phase equilibrium and thermodynamic data. The databases contain parameters of models specifically developed for molten slags, liquid steel and solid oxide solutions such as spinels, pyroxenes, olivine, monoxide (wustite, periclase, lime), corundum, etc. By means of the optimization process, model parameters are found which reproduce all thermodynamic and phase equilibrium data within experimental error limits. Furthermore, the models permit extrapolation into regions of temperature and composition where data are not available. The databases are automatically accessed by user-friendly software that calculates complex equilibria involving simultaneously slag, metal, refractories and gases, for systems with many components, over wide ranges of temperature, oxygen potential and pressure. A short review of the available databases is presented. The critical evaluation/optimization procedure is outlined using the Al2O3-CaO-FeO-Fe2O3-SiO2and Al2O3-CaO-MnO-SiO2systemsas examples. Several applications of the databases to deoxidation of iron and to inclusion control in steel are discussed. Keywords: thermodynamics, phase equilibrium, phase diagrams, databases, ferrous metallurgy, steelmaking, inclusion control, slags, oxide systems.

Jan 1, 2004

By Kenneth L. Whitehead

After many years of research, the occurrence of pneumoconiosis, black lung disease, among miners has been related to the mass of respirable coal dust to which mining personnel have been exposed. Congress passed Public Law No. 91-173 in 1969, which limited the dust concentration of respirable dust allowed in the mine working areas to 2.0 mg /M3 as of December 31, 1972. As a result of these restrictions, much work has been done in determining methods of either eliminating or suppressing respirable dust. The purpose of this project is to determine the state-of-the-art in continuous mining machine bit technology, particularly with regard to dust production.

Jan 1, 1973

By G. C. Hall, B. E. Hobbs

Giant gold deposits are considered products of crustal-scale systems. Reduced fluids stored in mid to lower crustal reservoirs were discharged into mid to upper crustal sites of deposition. Elements of the architecture include crustal-scale structures, reduced packages of rock and regional seals. Gas-rich aqueous fluids were common but non-aqueous fluids may have been significant in the deeper parts of the systems. Fluid fluxes in over pressured domains were maintained by porosity waves. Abnormal heat input from the mantle may not be required once the systems were perturbed. Fluid-mixing and hypogene enrichment were probably the most significant precipitation processes.

Jan 1, 1999

By Lin Daoyi

In this paper, we have adopted the high pressure jet-grouting curtains to seal the sea-water, and to consolidate the wall of the well for deep foundation diteh, make a pladge of building and construction of deep foundation was primarily on progress without water. This paper, we have been given a test for pumping water under mainly the circumtances of sealing condition and to report in advance the capacity of seawater seeping into the gam curtains in the process of building and construction of deep foundation.

Jan 1, 1991

By K. Heasley, A. Yassien, A. Khair, S. Peng

There are three major components of a fully grouted roof bolt which primarily determine its ability to develop and sustain load: the steel rebar, the resin annulus, and the rock/grout interface. The untensioned, fully grouted roof bolt is subjected to loading only when the surrounding rock deforms. Vertical rock deformation is generally a result of strata sagging and bedding plane separation, whereas horizontal deformation is typically a result of bedding plane sliding. These two types of deformation create different types of internal loads with-in the roof bolt, tensile stress for vertical rock deformations and shear stress for horizontal rock deformations. Also, as a result of the mutual load transfer between the rock and bolt, shear stress will be developed along the grout/rock interface. According to the exact bolt loading conditions, different failure modes may occur: bolt axial failure, bolt shear failure, and shear failure along the grout/rock interface. Understanding these possible failure modes and their root causes is the key to eliminating roof failures in underground mines employing fully grouted resin bolts. Using ABAQUS 5.8, a finite element model was developed to simulate the components of the fully grouted bolt and its interaction with the surrounding roof strata. Several models were conducted to investigate how load transfer occurs between the rock and the bolt under different geological and mining conditions. The effects of bed-ding plane location and properties, and strata sequence on bolt stability were studied. Also, the effects of hole roughness on bolt stability were discussed. Bolt axial failure was not observed within the range of the studied parameters; however, a combination of high overburden depth, a bedding plane located at 2 to 3 ft from the roofline or a low coefficient of friction along the bedding plane caused strata sliding and shears failure in the bolt. Also, in the case of a weak immediate roof, the shear stress at the grout/rock interface could exceed its ultimate capacity lead to slippage.

Jan 1, 2004

By Albert Adu-Acheampong

Fairmount Mineral's Maiden Rock underground sand mine historically delivered air to ventilate diesel-powered equipment at its working faces through high-resistance, 381-mm- (15-in.-) diameter PVC distribution lines. In support of plans for expanded production, three new, low-resistance ventilation design alternatives were analyzed. The study determined that adequate ventilation for expanded production was possible with various commercially available, high-volume/ low-pressure fans combined with a systematic layout of control structures. The recommended redesign was implemented in 2001, resulting in a significant increase in flow volumes and a noticeable improvement in the mine environment.

Jan 1, 2008