Search Documents

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitled ?Evaluation of Proximity Warning Devices? dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electrostatic fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factor of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By J. J. Demeter

Experiments were conducted in 2- and 4-inch-diameter standpipes to evaluate the effectiveness of standpipes as pressure seals. During the experiments, these standpipes conveyed Alan-Wood magnetite (60 to 230 U.S. standard sieve mesh) by gravity flow from one vessel to another of relatively higher pressure. The information obtained has been helpful in a Federal Bureau of Mines investigation of how to make either synthesis gas or hydrogen by a modified steam-iron process employing a continuous recycling stream of granular iron-iron oxide at temperatures of 600° to 900° C. In this process the mixture of granular material flows by gravity from a reduction vessel at low pressures to an oxidation vessel at higher pressures. Data from the 2- and 4-inch-diameter standpipes indicate that it would be practical to use a standpipe as a pressure seal between the reductor and oxidizer. Investigators found that, by gravity flow, the standpipe could convey the Alan-Wood magnetite against pressure gradients up to 1.07 pounds per square inch per foot of column height.

Jan 1, 1961

By Chen-Luh Lin, Jan D. Miller, Sindhoora Puvvada

The depletion of good-quality phosphate resources, coupled by a need to supply acceptable products at a rapid rate, while meeting the specifications of fertilizer chemical plants, is of significant concern to the phosphate industry, particularly the production of concentrates with tolerable dolomite content. Tremendous efforts have been made in the past to develop an efficient and economical process that can effectively reject dolomite. However, dolomite removal continues to plague the phosphate industry due to several process-specific challenges being encountered with various beneficiation technologies. In this regard, detailed characterization of phosphate reserves is crucial to understand textural limitations and help design appropriate strategies to achieve quality products. In this paper, the development of procedures to establish dolomite rejection/francolite recovery curves for gravity preconcentration of pebble phosphate from Central Florida is described using high-speed X-ray computed tomography (HSXCT). The developed procedure is illustrated with the analysis of high MgO pebble phosphate samples (10.39 mm × 1 mm) received from South Pasture and Four Corners locations operated by the Mosaic company. The rejection/recovery curves were calculated for each sample for five different particle size classes to observe the trend in rejection/recovery with variation in particle size. In order to evaluate the reliability of the HSXCT data, analysis using the high-resolution X-ray computed tomography (HRXCT) technique was performed on one particular sample (FC-3-1). Finally, to assess the separation efficiency, the HSXCT and HRXCT rejection/recovery curves obtained were compared to experimental gravity preconcentration results reported in the literature. In this way, liberation limitations for gravity preconcentration in the processing of pebble phosphate have been established based on X-ray computed tomography analysis.

By G. A. Kosick, C. A. Harris

"Metallurgy at the Polaris Mine is approaching an impasse, with lead and zinc concentrate grades and recoveries approaching their theoretical maximums. In an effort to increase productivity, plant throughput and operating material costs became a major focus of milling personnel.one method of increasing plant throughput was to minimize flotation circuit upsets by; standardizing operating strategy, decreasing control action response time of operators, increasing training of operators, and providing a more available decision support system for operators.To achieve these goals, Polaris personnel decided to utilize expert system technology to develop a real-time process controller for the flotation circuit which would be capable of justifying its actions to operating personnel.This paper describes the procedures followed in constructing the first process controller in the mineral industry which is based on the principles of Artificial Intelligence.IntroductionThe Polaris Concentrator was constructed in 1980 on a barge in Trois Rivieres, Quebec and towed to its present location on Little Cornwallis Island, North West Territories, about 1450 kilometers from the North Pole. The plant presently treats about 2,800 MTPD of new feed with average feed grades of 3% Pb, 13% Zn and 5% Fe. Current production averages 36,000 tonnes of lead concentrate and 220,000 tonnes of zinc concentrate annually.In an effort to increase the efficiency of the concentrator, the decision was made to implement an innovative control system on the flotation circuit. This system would embody and utilize heuristics ""rules-of-thumb"" gained from operators to make on-line process decisions. It would also justify these decisions on a demand basis."

Jan 1, 1988

By Fred D. DeVaney, C. W. Ambler

"Copper sulphate is a common flotation reagent for blende ores. Metallic iron also is present in the mill circuit, and a reaction between the iron and the salt would be in accord with well-known chemistry. The abundance of metallic iron in a flotation feed may be noted by even perfunctory examination. First of all the mine contributes metallic iron, then the coarse-crushing machines add their share, and finally the fine-grinding medium its portion. If the grinding is with cast-iron balls the amount of metallics is greater than when steel is used. Thus it is that much more metallic iron is present than would be indicated by noting the ball consumption. An estimate that the total amount of metallics is twice that supplied by the balls and liners might not be far amiss.That copper sulphate plates out on iron in an acid solution is well known, but since flotation is practiced commonly in solutions where acid has not been added this reaction has not been given sufficient thought.This problem has been the basis of a study undertaken jointly by the Mississippi Valley Station of the United States Bureau of Mines and the Missouri School of Mines and Metallurgy, at Rolla, Missouri. Its importance may be understood better when the tonnage of zinc ores now being treated by flotation in this country is considered. According to Gaudin4 5,536,244 tons of zinc or were treated by flotation during 1927. In these operations copper sulphate was employed as an activating agent; the amount per ton averaged 0.81 pound for straight sulphide zinc ores and 1.16 pounds for complex ores. Since such large quantities of zinc ore are treated by flotation and since metallic iron is always present, the importance of studying their reactions on each other and the effect of their reaction"

Dec 1, 1929

By AIME AIME

General Local Committee.-John Fritz, Chairman; A. B. de Saulles, Vice-Chairman.; R. M. Bird, Treasurer; Henry S. Drinker, Secretary; Robert H. Sayre, E. P. Wilbur, Charles M. Dodson, Abraham S. Schropp, E. M. McIlvain Archibald Johnston, A. B. Fichter, C. G. Convers, W. A. Wilbur, Garrett B. Linderman, Frederick Conlin, George Pettiuos, Albert Brodhead, Garrett L. Hoppes, M.B. Cutter, H. J. Seaman, C. A. Matcham, B. F. Fackenthal, Jr., A. L. J. Queneau, Geo. R. Elder, Eldridge Wilbur, William H. Chandler, Mansfield Merriman, Joseph F. Klein, William S. Franklin, William Esty, Joseph AN'. Richards, Howard Eckfeldt, John D. Irving. Transportation Committee.-H. J. Seaman, C. A. Matcham, B. F. Fackenthal, Jr., A. B. Fichter, A. L. J. Queneau, Henry S. Drinker. Hotel Committee. -Garrett B. Linderman, Charles M. Dodson, W. A. Wilbur, Garrett L. Hoppes, Albert Brodhead. Steering Committee.-William S. Franklin, William Esty, John D. Irving, R. M. Bird, the members of the Tau Beta Pi Society of Lehigh University. Committee on Meetings - William S. Drinker, Joseph W. Richards, Howard Eckfeldt. Entertainmment Committee.-W. A. Wilbur, E. M. McIlvain, Archibald Johnston, A. B. de Saulles, G. G. Convers,.A. L. J. Queneau, Garrett B. Linderman, Frederick Conlin, George Pettinos, Garrett L. Hoppes, Henry S. Drinker, William S. Franklin, Eldridge Wilbur, Robert M. Bird, Secretary. The opening session was held at 8.30 p.m., Wednesday, February 21, 1906, in Gymnasium Hall of Lehigh University, which had been tastefully decorated with flags and bunting. Dr. Henry S. Drinker, President of Lehigh University, and Secretary of the General Local Committee, called the meeting to order, and welcomed the Institute to the Bethlehems, where its first meeting, after its organization in May, 1871, at Wilkes-Barre, was held in August, 1871.*

May 1, 1906

By R. Boom, J. Halder, B. Snoeijer, B. Deo, A. Overbosch

Operational data of BOF and the slag samples for different starting conditions of phosphorus(0.06–0.26 per cent P) and silicon content (0.3–1.2 per cent Si) of hot metal have been analysed. The contribution of parameters that are well known to affect phosphorus distribution at tap, like basicity, temperature, FeO content of slag, slag mass etc., is investigated through the models of ionic theory of slag, optical basicity, regular solution approach and molecular theory of slag. The best overall results are obtained by the model based on molecular theory of slag in which several operational parameters are also incorporated. The investigations of different slag samples, based on optical, SEM, EPMA and X-ray studies, reveal the effect of MgO and Al2O3on slag morphology and phosphorus distribution in different phases. It is important to consider phosphorus distribution ratio in the solid and liquid part of slag. The solid part of slag, which is mostly dicalciumsilicate, can contain up to 5 per cent phosphorus. The phosphorus content of the liquid part of slag may depend upon the phosphorus content of hot metal or phosphorus load of slag. It is found that incorporation of effect of dicalciumsilicate in the model improves the accuracy of prediction. For better process control, the addition of iron ore towards the end of blow must be avoided while treating high phosphorus hot metal or during the production of ultra low phosphorus steels. Keywords: steelmaking, BOF, phosphorus distribution, slag morphology, MgO, Al2O3,dicalciumsilicate, process control, models

Jan 1, 2004

In 2004, a total of 741 nonmetal mining operations reported employment to the Mine Safety and Health Administration (MSHA). These mines (e.g., potash, gypsum, salt) comprised 5.1% of all operations.

Sep 1, 2007

By A. L. Grabovski

The potential of eccentric cone crushers for fine crushing has been improved by increasing the swing frequency of the moving cone, balancing the crusher, ensuring uniform feed via a rotating funnel with sideways discharge, introducing hyperbolic motion and employing the inertia crushing method, but further improvements to the specifications of existing cone crusher designs are limited by the rigidity of their kinematic coupling. A new design has been developed which combines two crushing modes, stone on liner and stone on stone, each with its own advantages. The main aims are to produce finer materials and to reduce liner weight. The benefits include an increase of more than 10% in the output of fine particles, improved protection of the liner against wear, as a result of filling of the cavities by material being crushed, and the use of almost 20% less material in casting of the liner. The chamber can be used in place of the usual liners of fine cone crushers

Jun 21, 1905

By A. Nieto

A dump edge and vehicle proximity warning system is being developed at the Colorado School of Mines using GPS and wireless local area networks to improve the safety of off-highway trucks in open pit mines. After two years of research, software development, and testing in the laboratory, field tests are currently being carried out at operating limestone quarries and open pit mining operations to evaluate the effectiveness of the system under rugged operating conditions. This paper describes the progress made on this NIOSH-funded project and discuss, tests carried out recently, at the Morenci open pit copper mine in Arizona.

Jan 1, 2002

By B Mohanty, Y C. Lizotte

Optimization of blast fragmentation in underground hardrock mining requires analysis of its effects on loading and haulage equipment, together with the downstream materials handling system, with the objective of minimizing total mine operating costs. A methodology is reported which has been developed to quantify the actual fragmentation and equipment performance in the field. This is data which has seldom been practicable to capture nor received serious attention in mines. Based upon the experience gained in underground studies, a prototype standard is proposed which aims to summarize the pertinent data, collection and analysis for fragmentation assessment. This relates to parameters of direct measure, such as mean size and distribution, as well as muckpile and work environment. The paper concludes by defining the impact of fragmentation on the loading and downstream handling system.

Jan 1, 1991

Productivity in underground metal and nonmetal mines is contingent upon work methods, mine layout, and ore handling techniques. One of the most important factors impacting productivity is the efficient movement of men, materials and supplies from the surface into and throughout the mine. Various transportation systems such as man-trains, service shafts, rubber-tired diesel equipment, etc. are currently used to transport men and supplies in underground mines. In many underground mines, it is not uncommon for a worker to spend 25% of his eight-hour working day traveling from the surface to his work area and returning to the surface.

Jan 1, 1975

A summary of a proposal to develop a 20 000 tpa underground gold operation in a Forest Park. The environmental constraints are severe and affected the mine development planning and choice of mining method. The mine will use trackless methods to access the narrow 1.5 m ore shoots, and to mine ore by cut and fill methods. The use of Microscoop and CT 1700 HE electric LHDs for mucking, together with special drilling attachments for drilling, is central to efficiency and small Kubota diesel haulers will be used for carrying ore to surface.

Jan 1, 1986

By P. J. Watson

The objective of this study was to prioritize the potential risks nuisance and biologically active dusts and fumes present in metal and nonmetal mines. This was accomplished by ranking numerical values derived from a matrix formula calculation that took into account dose, mine population, and sampling size. Data used in these calculations were obtained from the Mine Inspection Data Analysis System (MIDAS). The dusts determined to have the highest risk potential were quartz respirable particulates, mine dust, cristobalite respirable particulates, welding fume components, and nuisance respirable dust. Other dusts and fumes that were not ranked in this study, due to small sampling population, but which show a potential risk, include asbestos, talc, hydrogen cyanide, organic compound dusts, arsenic, metal dusts, and metal and nonmetal fumes.

Jan 1, 1987

By Jerry E. Olson

In 1984, the U.S. Bureau of Mines conducted a mineral survey of the Pahute Peak Wilderness Study Area (WSA) (NV-020-621), which covers 57,529 acres in Humboldt County, NV. About 90 percent of the WSA is underlain by Tertiary volcanic and shallow intrusive rocks. Of the remainder, metasedimentary rocks of unknown age are in contact with Cretaceous intrusive rocks in the northwest corner of the WSA. The entire WSA is within an upthrown fault block of the Basin and Range physiographic province. Portions of the WSA, especially south of Pahute Peak (Big Mountain), may be part of an eroded caldera structure. No mines or evidence of major exploration were identified within the WSA. Workings in Copper Canyon, claim blocks along the northwest boundary, and zones of anomalous character as defined by the Bureau of Land Management were examined. No mineral resources were identified, but sample results indicate three significantly mineralized sites, one with indications for zinc skarns in Copppr Canyon, another favorable for precious metals 2 miles south of Copper Canyon, and another area near the northwest boundary with geologic conditions characteristic of molybdenum deposits. Further investigation of these sites is warranted. Petrified wood is present in small amounts near the west central range front.

Jan 1, 1986

By S. Ranganathan

Production of ferro-chromium in the submerged-arc furnace is highly energy-intensive. Several process rates have been attempted to reduce the specific energy consumption in the production of this alloy. An exhaustive understanding of the thermo-chemical features of the production process can be used to reduce the specific power consumption significantly. The knowledge can be used to reduce the energy drain through undesired reactions in the process can be minimised. Plant trials have shown that specific energy consumption up to 100kWh/tonne of hot metal can be obtained by adopting this strategy. The process requires modification in operation practice and does not require any capital investment unlike other processes adopted for reducing power consumption. The principle of thermo-chemistry involved in this process development and results of plant trials are discussed in detail.

Jan 1, 2007

By Kathleen M. Kowalski-Trako?er

National Institute for Occupational Safety and Health re­searchers conducted a study to investigate the human response issues related to wearing a self-contained self-rescuer (SCSR). The goal was to develop training to educate miners on what they could expect from their units during an escape. Subjects included miners who had experience wearing SCSRs, manu­facturers, and researchers. Results identified nine key areas of concern: (1) starting the unit, (2) unit heat, (3) induction of coughing, (4) unit taste, (5) difficulty in breathing while wearing the unit, (6) quality of the air supplied, (7) nose clips, (8) goggles, and (9) the behavior of the breathing bag. In addition, researchers reviewed the literature on human response under duress. This article describes the expectations training program, which comprises the findings of the SCSR study and what is known about the normal human response in an emergency. The authors present background on SCSRs and the SCSR switchover procedure mandated in the recent federal Mine Improvement and New Emergency Response Act of 2006, which provided the impetus for the expectations training. Keywords disaster, escape, mining, self-contained self-rescuer, training

Jan 1, 2008

By R. J. Hickson

From 1993 through 1999 Cyprus Amax Minerals Company successfully completed eight major construction projects around the world. Six greenfield mines were brought into production, an ongoing operation was completely modernized, and an environmental issue was appropriately remediated. The projects stretched over three continents, from arctic Russia to the Atacama Desert, from 16,000feet to sea level, from city suburbs to remote wilderness, from a low of $130 million to over $1 billion. Open pit and underground; mill and leach; gold, copper, molybdenum, and coal were all encompassed. The breadth of diversity experience from these projects inspired Cyprus Amax to create a “best practices” project management protocol, to steer corporate expansion into the next millenium. This paper summarizes those best practices, while high-lighting project management pitfalls to avoid.

Jan 1, 2000

By P Allen, E Gleeson, D Boakye, R Chesher, S Konopa

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Not only do epithermal gold deposits provide many challenges in estimating mineral resources, the complexities of these deposits also provide technical challenges in assessing appropriate mining and processing strategies, as well as social and environmental planning and management. The characteristics of epithermal gold deposits include being highly variable with respect to geometry and gold grade distribution, the presence of other economic contributors, mineralogy, texture, rock strength, weathering and alteration overprint. These characteristics influence the economic value of mining projects in an interlinked manner. Consequently, successful exploitation of epithermal deposits requires a holistic approach, coupled with the effective integration of geological data to meet all aspects of mine development decision-making. This paper presents examples of the key technical challenges encountered in estimating and mining epithermal deposits. It also highlights why these issues need to be addressed from the viewpoint of geology, sampling, resource estimation, mine planning, mineral processing and social and environmental planning for the true value of the mining project to be realised.CITATION:Konopa, S, Chesher, R, Gleeson, E, Allen, P and Boakye, D, 2015. Challenges in maximising the value from epithermal gold deposits, in Proceedings PACRIM 2015 Congress, pp 127–132 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Dolly Chakraborty, S. Ranganathan, S. N. Sinha

Experiments were conducted to study the influence of temperature, particle size and ore/coke ratio on the kinetics of reduction. The rate of reduction increased with temperature. The reduction of iron was completed at shorter time intervals at temperature above 1000ºC. Usually the reduction of chromium commenced after the reduction of iron was almost complete. Reduction was controlled by diffusion at low temperatures and by chemical reaction at higher temperatures. The nature of the reducing agent had a very significant influence on the rate of reduction. The study showed that chromium was converted into the carbide during reduction. Increasing the size of the reducing agent increased the rate of reduction initially. After a critical size, the rate of reduction decreased. However, increasing the size of the ore particle decreased the rate of reduction, initially. Beyond a critical size, it increased. An optimum particle size of the chromite ore and that of coke must be chosen, particularly in the production of agglomerates to achieve maximum degree of reduction.

Jan 1, 2007