Search Documents

By K. Peake, A. Dalvi, V. Hernandez, S. Chang, M. Oliazadeh

"Ironstone Resources Ltd. is developing the Clear Hills oolitic iron ore deposit in northwest Alberta, Canada. Sources of oolitic iron ore worldwide are abundant and ubiquitous, but there is currently no commercial technology to extract iron from oolitic iron ores. Mineral processing of the ore to generate a commercial iron ore concentrate is very challenging due to the nature of these ores. Accordingly, Hatch and Ironstone are developing a new pyrometallurgical process (Hatch Ironstone Chloride Segregation) to produce metallic iron from high silica and high phosphorus oolitic iron ores. Following the chloride segregation process, the treated ore is subjected to fine grinding. The iron is then separated by magnetic separation. The iron grade and phosphorus content of the final product shows a strong dependence on the separation methodology and the grind size. The pyrometallurgical process has been developed and tested at a lab-scale pilot plant. The commercialization of this technology could provide an opportunity for the development of a new alternate iron making technology. This paper presents the results of test work done on the raw iron ore to create a concentrate and also on the products of the pyrometallurgical process for the production of a high grade 90% metallic iron product.INTRODUCTION Oolite is a sedimentary rock formed from ooids – spherical particles with concentric layers. There are a number of large oolitic iron deposits where the mineralogical form features a low iron content and high concentration of impurities making them presently impossible to exploit on either a technical or economic basis. The fifteen largest oolitic iron ore deposits in the world are estimated to contain approximately 337 billion tonnes of iron ore, which would be a significant source of supply for worldwide steel production. A viable process that can economically recover iron from these oolitic iron ore deposits could become an important new technology to meet future demand in the steel industry. Hatch and Ironstone have demonstrated that oolitic iron ores can be exploited to produce direct reduced iron (DRI). Direct reduction ironmaking is a method for producing solid metallic iron using different techniques compared to the blast furnace process, which is the more conventional ironmaking route. The demand for the construction of direct reduction ironmaking plants has increased in response to the increasing demand for crude steel. It is viewed as a method of providing low-residual iron sources to scrap-based steelmaking in electric arc furnaces."

Jan 1, 2014

In their excellent paper, Milev and Spottiswoode have provided quantitative and definitive descriptions of an important phenomenon that hitherto has been largely the subject of conjecture. They convincingly show that ?site-response? can amplify the strong ground motions on the rock-wall of a stressed tunnel by a factor of 10 to 12 compared with the PPV in the solid rock mass (at the same distance from source). This knowledge gives us a firm foundation from which to begin to build an understanding of the mechanism of damage resulting from a rock burst. Regrettably this understanding is still far from adequate, in my opinion. The authors of this paper, however, have made some statements that are too reassuring and which tend to reinforce the sense of complacency that prevails among many members of the rock engineering community on the deep gold mines.

Jan 1, 2006

By A. Krause

Shovel-truck systems for loading and hauling material in open pit mines are now routinely analysed using simulation models or off-the-shelf simulation software packages, which can be very expensive for once-off or occasional use. The simulation models invariably produce different estimations of fleet sizes due to their differing estimations of cycle time. No single model or package can accurately estimate the required fleet size because the fleet operating parameters are characteristically random and dynamic. In order to improve confidence in sizing the fleet for a mining project, at least two estimation models should be used. This paper demonstrates that the Machine Repair Model can be modified and used as a model for estimating truck fleet size in an open pit shovel-truck system. The modified Machine Repair Model is first applied to a virtual open pit mine case study. The results compare favourably to output from other estimation models using the same input parameters for the virtual mine. The modified Machine Repair Model is further applied to an existing open pit coal operation, the Kwagga Section of Optimum Colliery as a case study. Again the results confirm those obtained from the virtual mine case study. It is concluded that the Machine Repair Model can be an affordable model compared to off-the-shelf generic software because it is easily modelled in Microsoft Excel, a software platform that most mines already use. This paper reports part of the work of a MSc research study submitted to the University of Witwatersrand, Johannesburg, South Africa. Keywords: simulation, bunching, probability distributions, cycle time, queuing, matching, shovel-truck, OEM.

Jan 1, 2007

By R H. Sillitoe

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Geological concepts are employed routinely in porphyry copper exploration at the area selection, prospect appraisal and deposit definition stages. Regional, district-scale, deposit-scale and laboratory-based concepts can all play a role, with the resulting porphyry copper models providing templates for the integration of geochemical and geophysical responses and interpretations. Of the 19 concepts and parameters selected for brief discussion, those relating to subdivision of porphyry intrusions, understanding of diverse and commonly complex alteration-mineralisation patterns and lithocap characterisation are undoubtedly the most influential in exploration. Several of them are of particular importance because of their role in promoting grade development. Additional belt-, district- and deposit-scale features are currently little used but hold promise, whereas others have less practical value but help in underpinning the evolving porphyry copper genetic model.CITATION:Sillitoe, R H, 2015. Recent advances in porphyry copper geology and their exploration utility , in Proceedings PACRIM 2015 Congress, pp 35–44 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M Carr, K Williams, W Chen, J Plinke

The depletion of iron ore deposits at the face of the mine site dictates the necessity for the exploitation of formerly less attractive orebodies to meet the demand of the modern world. These orebodies will typically be found close to or even beneath the water table where an increasing clay and moisture content will result. Problematic iron ores, colloquially termed as ‘wet and sticky’ material (WSM), can have a significant impact in the material handling stream due to the expensive downtime of processing equipment, which is attributed to the inter-particle and boundary cohesion and adhesion forces of the bulk material.In order to gain a better understanding of the causes of poor handleability, experimental test methods to determine wall adhesion, and inter-particle adhesion within bulk materials were developed. Based on the combination of wall adhesion and inter-particle adhesion measurements, with traditional methods of assessing bulk material handleability, a new method to assess the potential of bulk materials to cause handling problems is proposed. This method reduces the multitude of factors leading to problematic behaviour to a handleability index (HI) [0,1], which is easily assessed and understood. The method is suitable for adhesive materials and applicable for a wide range of material flow, from gravity reclaim stockpiles to transfer chutes and carry back on conveyor belts.Additionally, this research presents an assessment of the HI derived by experimental testing of three iron ore samples. A clear understanding of the problematic behaviour of the iron ore samples is achieved with the use of dust extinction moisture (DEM) tests, which indicates the regions where problematic behaviour may be experienced on-site.CITATION:Carr, M, Plinke, J, Williams, K, Roberts, A and Chen, W, 2017. Determination of the handleability index of adhesive bulk materials, in Proceedings Iron Ore 2017, pp 503–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

Delhi Australian Petroleum Ltd., acting as operator for the joint interests of Delhi and Santos Ltd., has been engaged in petroleum exploration in the western Great Artesian Basin since 1958.Extensive airborne magnetometer, gravity meter, reflection and refraction seisomograph, and surface geological surveys have been carried out. Results of the surveys have considerably altered the concepts of the geology of the area.Seven exploratory wells have been drilled in the area. Results of the drilling have established the presence in the subsurface of previously unknown Paleozoic sediments which are capable of generating hydrocarbons.Production of oil or gas has not been achieved, but each phase of the exploration programme has resulted in progressively establishing the basic conditions necessary for the discovery of commercially profitable accumulations.INTRODUCTIONDelhi Australian Petroleum Ltd. commenced operations in Australia in 1958. They have subsequently been engaged in systematic exploration for oil and gas, acting as operator for their partner, Santos Limited. The methods and techniques employed are those used throughout the petroleum industry. The results of the exploration programme contribute to a better understanding of the basic geology, and concomitantly a firmer analysis of the petroleum producing potential, of the western Great Artesian Basin.Each phase has progressively enhanced the gross geological interpretation of the area with regard to favourable conditions for the generation and accumulation of hydrocarbons, but the stage has not been reached where productive potential is definitely established.Exploration status in 1958Basin configurationIn 1958 knowledge of the pre-Jurassic stratigraphy of the geographically defined western Great Artesian Basin...

Jan 1, 1964

By B. J. Kloppers, J. V. Z. Visser, C. J. Horn

"The long-term plan (LTP) in a mineral resource company is defined by the quality of the mineral resource and represents the result of a series of trade-offs to fulfil internal organizational as well as external business and legislative requirements, ensuring ultimate delivery on the defined organizational strategy.The LTP should as a whole align to a coherent and well-defined organizational strategy, working towards a clearly defined objective while still allowing a tactical response to short-term requirements of the organization. The ability to respond tactically to changes in environment, like the unprecedented five-month strike in 2014 on the platinum belt following the 2012 Marikana incident, is a measure of the flexibility of the plan given the agreed strategy.This paper describes the Lonmin process of linking company strategy with long-term planning, tactical planning, and the execution of the plan through an annual planning cycle to maximize organizational flexibility. This flexibility enables mining companies to respond to the many internal and external forces that impact on both strategy formulation and delivery of results that meet shareholder expectations."

Jan 1, 2015

By Stefan Basista, Janusz Tomala

Modern constructions of electric ferroalloy furnaces are still based on applying in the lower "liquid" areas the standard carbon materials. What can be illustrated by the experience from several years, in the part of tap hole, hearth walls and bottom, is that so-called carbon or semigraphite microporous materials are successfully being applied. These materials, compared to the standard carbon, give better resistance to the attack by liquid metal and other wear factors. Generally this group includes materials characterised by considerable share of pores of diameters below1µm (significantly exceeding 90% of total porosity). The microporosity increases the resistance to the infiltration of the liquid metal. The effect of microporosity can be obtained by introducing silicon (or its compound) additive to materials based on electrically (or gas) calcined anthracites, electrographite and binder. Moreover, by introducing other ceramic additives, the microporous materials are more resistant to dissolution by the liquid metal. Observing the trends of "improving the materials" in the last years, it is clearly seen that the share of non-carbon additives is bigger and bigger, so we can reasonably speak of rather carbon-ceramic materials. In this paper, the survey of the most important quality criteria, which must be met by the carbon furnace linings, as well as the new testing methods will be presented.

Jan 1, 2007

By Nabil F. Ismael

The axial capacity of step tapered bored piles in sand was examined by field tests at one site in Kuwait. Two straight piles, and two step tapered piles were load tested in compression to failure. All four piles were 3 m deep. The straight piles were 0.2 m in diameter. The step tapered piles had a diameter of 0.3 m for the upper segment which extended up to 40% of the pile length changing to 0.2 m diameter for the lower section. The soil profile consists of medium to dense sand with minor cementation and no groundwater was encountered. Both the ultimate bearing capacity and the settlement at working loads were examined. The axial capacity of the step tapered piles was greater, and the settlement at working loads was less, compared with the straight shaft piles. The increase in capacity is mainly attributed to the added side friction along the larger diameter top segment of the shaft.

Jan 1, 2008

Commercially interesting deposits of zeolite rich tuffs and amorphous silica have been discovered recently in the Taupo Volcanic Zone (TVZ), North Island, New Zealand. This paper reviews them and comments on the potential for further discoveries. Potential markets for these unusual industrial minerals are discussed.

Jan 1, 1997

By Wayne Rogers, Kell Monro, Arthur Pacunana

The Phu Kham Copper-Gold Operation (PKM) is a large-scale open pit mine located in northern Laos. It was developed and is operated by Phu Bia Mining Limited (PBM) a Lao-registered subsidiary company of Australian incorporated, PanAust Limited. Production commenced at Phu Kham in 2008. Since the second half of 2016, there has been a significant increase in ore hardness and this has negatively impacted the PKM concentrator and resulted in lower SAG mill throughput rates. Over the remaining life of mine, the changing ore body and increase in ore hardness is forecast to continue as the pit deepens and the availability of softer blending ores reduce. To manage this risk, PKM initiated a Hard Ores Management Program to determine the most effective way to improve the mill throughput of harder ores. This involved conducting a number of innovative and process control driven blasting trials to optimize run-of-mine (ROM) fragmentation and other blasting outcomes. From 2016 to 2017, the performance of high powder factor blasting, electronic detonators and fast timing, high velocity of detonation (VOD) explosives, double-priming, and deck blasting, were individually and systematically assessed. The success of each blasting trial was then based on a ‘value for money’ criteria. This criteria is a cost / benefit analysis that weighed-up the additional cost to implement the trial against the measured improvement in mill throughput. Electronic and high VOD 90:10 emulsion:ANFO blasts were determined to have the best value for money, achieving an increase in mill throughput of 54% compared to baseline. This paper discusses how the implementation of an innovative and process control driven blasting trial methodology was able to successfully manage the hard ore challenges at PKM. In addition, this success was achieved without any major cost implications, safety incidents or process plant set-backs.

Jan 1, 2018

By T. Lindstad, S. Gaal, S. Hansen, S. Prytz

The SINTEF SiO-reactivity test, developed by Tuset and Raaness in the 1970?s, is a recognised method of characterising the ?reactivity? of carbonaceous reactants, used in the ferrosilicon and silicon metal industries. Recently, the test has been updated, which has resulted in the development of an extended and improved SINTEF SiO reactivity test. This has included updating the test reactor, control system, data-logging, handling and preparation of carbonaceous materials to be tested and measurement procedure. The scientific basis has been re-assessed, resulting in a new interpretation of the test results. The repeatability of the test has improved significantly, especially through system automation. In the ?old? test, the kinetics of the reaction: SiO(g) + 2C(s) = SiC(s) + CO(g) for a specific carbonaceous material was characterised solely by the ?R10? parameter, the volume of SiO(g) which passes un-reacted through the coke-bed as the concentration of CO in the outlet gas decreases from 18 to 10%. As both the kinetics and obtainable conversion of SiO to SiC for a reductant is of importance to the ferroalloy producer, the new SINTEF SiO reactivity test ranks carbon materials both according to degree of conversion and reaction rate. From research carried out on the test in the past couple of years at SINTEF and NTNU, it has also become clear that some of the reactions taking place in the test reactor are more complex than previously assumed. As an example, it was previously assumed that the condensation reaction of SiO gas in the condensation chamber of the test reactor can be described as: 2 SiO(g) = Si(l,s) + SiO2(s). However, it has been established that the side-reaction: CO(g) + 2Si(l) = SiC(s) + SiO(g) causes approximately 10% of the total volume of CO to react to SiC and SiO2 in the condensation chamber. This means that some back-reaction i.e., the reverse SiO-generator reaction 3SiO(g) + CO(g) = 2SiO2 + SiC also takes place in the condensation chamber. In the new SINTEF test, the %CO versus time curves are therefore corrected in order to describe the effect of the reaction between SiO(g) and C(s) studied i.e., SiO(g) + 2C(s) = SiC(s) + CO(g). A correction-formula for this purpose is presented.

Jan 1, 2007

By H Li

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The central Nanling region in South China experienced multistage granite intrusive events and corresponding metallogenic processes during the Early Yanshanian period (190–140 Ma). In this study, a wide variety of published data on age determination, petrological characteristics, major and trace elements compositions, whole rock Sr–Nd contents and zircon Hf isotopic composition of the representative granite composites were systematically collected to estimate their cooling-uplift rates, granite evolution processes and mineral deposit formation. These granites have been classified into two groups based on their age and geochemical variations: Group 1 (180–165 Ma) and Group 2 (165–150 Ma). Major and trace element geochemistry suggests that Group 2 experienced more intense magmatic evolution and differentiation than Group 1. In addition, Group 1 granitoids are classified as A1-type alkaline rocks with faster cooling and uplift rates, whereas Group 2 granites are considered as A2-type aluminous rocks with slower cooling and ascent rates. Furthermore, the Group 1 granitoids have younger Nd and Hf two-stage model ages but higher eNd(t) and eHf(t) values, indicating influence from crust–mantle interaction. In contrast, the Group 2 granites show different values, suggesting stronger upper crustal contamination or assimilation. The slowly cooled and ascended Group 2 granites experienced much heavier crustal contamination (or assimilation) and crystal fractionation, contributing to the large W–Sn mineralisation in the central Nanling region. The Early Mesoproterozoic (1.6–1.4 Ga) crustal basement of the Cathaysia Block in South China is the ore source bed for the world-famous Nanling W–Sn polymetallic mineralisation.CITATION:Li, H, 2015. Where is the source of the world-famous Nanling W–Sn polymetallic mineralisation?, in Proceedings PACRIM 2015 Congress, pp 619–622 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By Virgil Miller

Bureau of Mines Reports of Investigations 3244, 3245, 3246 and 3264 give data of detailed studies on smelting in the lead "blast furnace handling zinciferous charges at Trail, B. C. The present paper gives more on analyses of the gases leaving the top of the charge and on accretions formed on the walls of the blast furnace. New data are presented to show the effect of the temperatures at the tuyere zone on the lead content of the slags made. The greater part of this paper, however, deals with a much debated subject, namely air used in lead blast furnaces. Original data are presented to show the effects on smelting lead 'products when air is supplied to a lead blast furnace under volume versus under pressure control.

Jan 1, 1940

By James J. Scott

Research and development has been carried out on the patented Dynamic Rock Anchor, tradenamed DYNA-ROK and DYNA-ROK PLUS Anchors, which are manufactured and marketed by Ingersoll-Rand Company. This paper will present the results of field testing of this revolutionary new concept in ground control. Geologic conditions will be described where the plastic sleeve of the DYWA-ROK anchor alone is sufficient to provide anchorage and also, where in softer ground conditions, the DYWA-ROK PLUS is applied. The rationale for making the decision as to the type of fixture to be employed, the length of plastic tube to be used and the quantity of resin are explained. Pull test data will be shown from eight different coal seams in the Eastern United States where the product has been installed.

Jan 1, 1990

By T. P. Meloy

A methodology is presented for finding feasible or locally optimal designs in the class of homogeneous, countercurrent, processing networks performing two-component non-sharp separations. The advantage of the methodology developed here is that given a set of independent performance criteria (specifications such as network separation factor, beneficiation ratio or recovery), a feasible or locally optimal countercurrent network design meeting those criteria can be found in one step. In the methodology, graph-theory was used to explicitly obtain the exact network responses of specific countercurrent networks. These responses were used to formulate the linear recursion equations whose solution gives the expressions for the countercurrent network responses which are a function of the stage transfer functions for two-component, non-sharp separations. These expressions are also functions of the network variables n and c. These expressions, together with the set of independent design criteria, were solved simultaneously for n and c using the Levenberg-Marquardt algorithm for systems of constrained, non-linear equations. The network variables n and c embody the coded network design information which is used to find the feasible network design which satisfies the set of independent performance criteria.

Jan 1, 1994

By B. Salt, R. Sullivan, E. Roos, M. de Vries, K. McKenna, L. R. Nelson, M. J. N. Uys, P. Jacobs, E. Munnik, P. Lewarne

A review is presented of the furnace cooling system design and operating developments since the initial furnace start up in January 2001 of the Chambishi DC-arc furnace to produce ferrocobalt alloy. The furnace operating conditions present a number of challenges to the furnace designers and operators in particular to provide a sustainable lining that can withstand the highly corrosive siliceous slag (roughly 50% SiO2). This is exacerbated by the dual requirement to operate this slag in a relatively highly superheated state (?T ? 400°C when tapped at 1550°C) to ensure that the ferroalloy can be tapped (estimated 1370°C alloy liquidus temperature) prior to atomisation. The core design challenge occurs at the alloy-slag interface, where a single refractory type cannot simultaneously meet the dual requirement of both adequate alloy and slag corrosion compatibility. Progression by the fourth furnace campaign to involve a retrofit of the bath sidewall to Hatch high-intensity, water-cooled, copper Waffle coolers and tapblocks is described. This involves operation of the entire slag bath, the slag-alloy interface and a portion of the alloy within a more chemically compatible refractory/slag (and possibly at times even an alloy) freeze-lining. Due to the high furnace power density employed (up to 500 kW/m2 hearth area) coupled with the large slag superheat needed, the resulting imposed peak bath sidewall heat fluxes are substantial, especially in the alloy (typically averaging 170 kW/m2), and on occasion have exceeded 1000 kW/m2. The performance of the Hatch Copper Waffle coolers under such aggressive process pyrometallurgical conditions is described. Aspects of the design and especially operating strategies to effect sustained production at up to 38 MW power input are also discussed.

Jan 1, 2004

By Franklin M. Grynkewicz

As part of the Boston Harbor clean up project, the new 1,000 mgd Deer Island Sewerage treatment plant includes ten 240 feet high egg-shaped "residuals" tanks. Contract documents called for these structures to be supported on 2,600 sixteen inch concrete filled pipe piles. The project site is underlain by highly variable glacial and marine deposits. Subsurface conditions vary from one extreme where firm glacial deposits exist at subgrade to the other extreme where 70 feet of medium stiff clays overlying weathered bedrock must be dealt with. The most common profile consisted of 15-20 feet of sands, 20-40 feet of marine clays, and 20-60 feet of stratified glacial deposits (commonly called tills) overlying Argillitic bedrock. Post bid redesign work, initiated as a cooperative effort between the owner and the general contractor, demonstrated that an $8 million savings could be realized if high capacity 48 inch diameter caissons replaced the specified pipe piles. A highly unusual arrangement of having the general contractor and specialty subcontractor providing input to the owner's engineering team allowed the redesign work to proceed on a "fast-track" schedule.

Jan 1, 1992