Search Documents

By M. Yavuz, M. Aksoy, G. Once, M. Iphar

This paper is concerned with a study on the floor heaving in the transport road of the GLI Omerler Colliery in Tuncbilek-Turkey. This gallery has been opened at the depth of 200 m through the formation of marl in 4.6 m width and 3.5 m height in cross section. Floor heaving occurred up to 70 cm in height in maximum and caused severe problems in railway and band-conveyor transportation in the main road. In addition; after the current panel mined out, the shield support units could not be transferred to the new panel because of the deformation of roadway cross-section. The I-profile steel arch supports also sank into the weak floor rock. This situation has been studied by numerical analysis using the FLAC3Dfinite difference program in order to investigate the rock mass behaviour around the opening. The obtained outputs of the numerical model have showed consistency with the amount of floor heaving in the gallery at 200 m depth. A new gallery has been driven at the depth of 115 m and M4 longwall panel has just been taken to production. So as not to encounter with the same problems at 200 m depth, especially longwall face moving problem, various numerical models have been studied in order to keep the floor heaving in the acceptable limits required to move shield support units. Keywords: Floor heave, Numerical modelling, FLAC3D, Failure criteria, RocLab

Jan 1, 2003

By N. Q. Huy

This paper describes the application of finite element analysis to simulate the static and quasi-static pile load tests in different drainage conditions. The possible effect of excess pore water pressure will be studied from the simulations results. The results show that the drainage condition has effect on the bearing capacity of a pile derived from the quasi-static pile load test. The excess of pore pressure reduces the pile toe resistance while it increases the pile shaft resistance. The factors which influence the effect of excess pore pressure are also discussed.

Jan 1, 2006

By A B. Christie, S C. Cox

Effective land-use planning requires accurate knowledge of mineral resource potential. Mineral companies during reconnaissance exploration, feasibility investigations and mine development also use this type of analysis. The Institute of Geological and Nuclear Sciences is undertaking a two-year project reviewing the resource potential of the West Coast of the South Island of New Zealand. Spatial prospectivity models have been developed as part of this resource assessment process, using computer based statistical pattern recognition techniques to delineate areas that are prospective for mineral deposits and to test deposit genesis models. Digital GIS data-sets of mineral occurrence were correlated against geology and exploration information. The distribution of mesotherrnal shear zone gold deposits in the Reefton Goldfield, were examined against geological data-sets from both the regional (QMAP) and local prospect-scale mapping. Weights of evidence analysis generated a correlation matrix that highlights relationships and degrees of association that might otherwise not normally be recognised.   Mesothermal shear zone gold deposits have strong positive spatial correlations with Greenland Group host rocks and areas with moderate to high quartz vein densities; moderate-strong positive correlation with regions <500 m from folds, with regions <600 m from faults and five to eight kilometres from granite contacts; moderate correlations with Ntrending fault and fold segments; and no/weak/poor correlations with fault intersections, fold-fault intersections, bends in regional structures and magnetic and radiometric data. The regional and prospect scale data sets give different results, with the more detailed prospect scale mapping giving generally better correlations. This emphasises the value of detailed geological mapping in the exploration process.   Maps generated by prospectivity modelling consistently highlighted areas of known mineralisation and generate targets where follow-up investigation is warranted. The prospectivity per unit area provides a measurable value that should change as new information comes to hand and, in addition to highlighting targets, can be used to measure the impact of increased exploration expenditure and assess the effectiveness of exploration investment.

Jan 1, 2001

By T. L. Johnston

The Dobbins property, about 4-1/2 miles northeast of Cartersville, Ga., was fist operated in 1866, it is the oldest manganese mine in Georgia and one of the oldest minus in the United States still producing manganese ore. Changes in ownership, lessees, and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property.

Jan 1, 1942

By T. L. Johnston

The Dobbins property about 4-1/2 miles northeast of Cartersville, Ga., was first operated in 1866. It is the oldest manganese mine in Georgia and one of the oldest mines in the United States still producing manganese ore. Changes in ownership lessees and operators and lack of records prevent the compiling of statistics regarding total production of ore from the property

Jan 1, 1942

By Qi Shifu, Guo Tao, Liu Haoquan, Yao Chaogui, Zheng Li

Abstract: To excavate oil-gas pipeline ditches in a rocky region or area the explosive method is needed. When a parallel ditch is to be dug by blasting near or in the vicinity of an existing pipeline, a safe criterion must be determined to ensure safety for the latter. In this investigation, with the construction of the second phase of the West-East Gas Pipeline Project, we carried out real blasting tests and numerical simulations to explore the safety criteria for the existing pipeline. Through this investigation, we obtained the safe strain elasticity threshold es2000µe, blast vibration velocity calculation formula, and the maximum vibration velocity Vmax=14cm/s(5.51in./s) for the pipe under blast shock loading, and worked out how to determine the charge size in the follow-up blasting excavation. These results can be used to determine the maximum explosive weight per delay and decide delays for the initiation circuit network in blasting a parallel pipeline ditch, and to make safety assessments for the existing pipeline in service. Having successfully been applied in the second and third phases of the West-East Gas Pipeline Project, China-Russia Oil Pipeline Project and China-Myanmar Gas Pipeline Project, these findings are very significant for other similar pipeline construction.

Jan 1, 2014

By C. Strachan

This paper presents an evaluation of tailings dam incidents from the 1994 USCOLD Tailings Dam Committee report. Comparisons are also made with water storage dam incidents from USCOLD reports and recent tailings dam incidents. The evaluation results show that tailings dam incidents are due to a number of factors including overtopping, static and seismic instability, seepage and internal erosion, and foundation conditions, and that no particular type of tailings dam or operational condition is more susceptible to incidents. In addition, the results confirm that tailings dams should be located, designed, operated, and reclaimed with a thorough knowledge of site conditions, mill operation, site monitoring, and tailings characteristics.

Jan 1, 1999

By L. Maday, V. J. Perrone, M. B. Gilbert

INTRODUCTION The Brightwater conveyance system project in King County, Washington consists of constructing about 21 km (13 mile) of effluent and combined influent and effluent tunnels. The influent tunnels will collect sanitary sewerage from the service area and convey it to the new wastewater treatment plant (WTP) site at Route 9 in Woodinville, Snohomish County, Washington. The effluent tunnels will convey treated effluent from the WTP to an outfall at Puget Sound. The tunnels will be constructed primarily under residential areas, busy suburban roads and state highways. This 21 Km (13-mile) soft ground tunneling project faced many design challenges because of the geologic and hydrostatic conditions, long tunnel reaches, and large overburden depths. Boring depths typically varied from 45.7 M (150 ft) to 114 M(375 ft) with a maximum depth of 185.6 M (566 ft) deep. Conventional empirical methods for non-mountain terrain based on a 1:1 ratio of drilled footage per foot of tunnel bore (National Research Council, 1984) for evenly spaced borings provided a good start for the Phase 1 explorations. However a continuation of this approach with closer spacing was deemed inadequate by the geotechnical team for efficiently allocating geotechnical exploration resources for the final design. This paper presents a rational approach that was used to evaluate the value of a particular geotechnical exploration boring, pump test or other in-situ test. The method of analysis, which was initially developed for rock tunnels (Einstein et al., 1978), was modified for the Brightwater project. The method considers the potential construction cost risks resulting from variable geologic conditions, the cost and reliability of the geotechnical exploration and the earned value (cost risk reduction) of performing the geotechnical exploration. PROJECT DESCRIPTION In total the land portion of the conveyance system will include approximately21 Km (13 miles) of tunnels ranging in size from 3.0 to 5.2 M (10 to 17 ft) minimum inside diameter with overburden depths of 30.0 to 168 M (100 to 550 ft) and

Jan 1, 2005

By N. L. Ayres

Tendon support systems have been successfully used to stabilize excavations. Tendon support systems are routinely designed using the axial load-bearing capacity of tendons, namely the tensile strength. To attain tensile strength the tendon must be loaded along its length, which often does not occur in practice. Tendons should optimally be installed at 90° to the surface of the excavation to achieve maximum penetration depth, yet this is often not physically or practically possible, and installations at angles less than 90° occur. Furthermore, the intersection of geological features within the rock mass frequently results in complex loading situations on tendons. The position and angle at which loading occurs results in different combinations of tensile and shear forces acting on the tendon, which can impact on the support performance of each unit and ultimately the whole system. All factors that influence the support system should be understood and taken into account to ensure a sound support design. Combination loading situations are further investigated and tested to obtain a better understanding of the mechanisms involved and the effects on tendon load-bearing capacity. Tendon support units were tested at different installation angles to establish the tendon performance, mechanical behaviour, and load capacity during these loading situations. The results and outcomes are aimed at providing rock engineers with additional data and improved understanding of how tendons could perform under certain conditions.

Jan 1, 2014

By Roy Peratrovich

An innovative cost-saving design for a 1,100 ft bulkhead on the Tanana River at Nenana in central Alaska won Alaska Construction & Oil magazine's Construction Achievement Award. The designers utilized materials available nearby at low cost. They planned sheet pile enclosures, self-anchored back into shore without cell closures. They made it practical for inexperienced local workers to do the building. And they completed the project on time and below a reduced budget.

Jan 1, 1985

Electroosmotic Dewatering and Consolidation of Mineral Waste Tailings

Sep 13, 2010

By Lloyd Rowson

??Several factors have led to a review and reoptimization of the Midwest uranium deposit by AREVA Resources Canada Inc., the project operator, on behalf of the owners ??The current proposal is to mine the deposit using open pit methods and then transport the ore by truck on a dedicated road linking the Midwest site with AREVA?s McClean Lake Operation (JEB mill) for processing ??A decision has been made to begin mining the deposit by 2010 (pending regulatory approvals)

May 1, 2008

By Becerra J. O

HYL developed a direct reduction process (DR) that does not require a reformer; it is called self-reforming process. Typically, direct reduction processes based on natural gas utilise a reformer unit to transform the natural gas into reducing agents (hydrogen and carbon monoxide). The reforming reactions are: CH4+H20-?3H2+CO CH4 + CO2 - 2H2 + 2CO These reforming units require a catalyst agent to promote the kinetics of the reforming reactions. The catalyst for these reactions is typically a metallic element such as nickel in a ceramic matrix; iron is also an excellent catalyst for the reforming reactions.

Jan 1, 1999

By K. Y. C. Chung

A case study on foundation engineering through organic soils is presented. Located along the west shore of the Hudson River, site soils consist of random brick fill over a thick layer of peat and organic silts or clays. The organic layer is underlain by medium dense to dense sand with varying amounts of silt. Strong artesian pressures were measured in the sand. A pile foundation system was selected to support all structures. To avoid periodic flooding, new fill must be placed on the existing fill. Large total and differential settlements will occur due to consolidation and secondary compression of the organic soils. This settlement will reduce the allowable pile capacity due to the large negative skin friction in the organic layer; and will necessitate long-term maintenance of the final grade elevation. Pile load tests were performed to determine the allowable compression and uplift capacities, long-term capacities and pile driving criteria.

Jan 1, 2010

By C Simpson

The Pilbara region of Western Australia is well known for its abundant exports of hematite-goethite deposits, which have been mined and exported since the 1960s. Magnetite has also been mined in Australia throughout this period, although historically of much lower production volumes (WA Iron Ore profile, 2016). Magnetite offers a source supply of material >66 per cent iron grade product, which is used as premium feed (predominantly pellets) to blast furnaces or specialised steel mills.The Iron Bridge project area contains outcropping magnetite and hematite banded iron formation (BIF), which within the region was recognised as having potential to host economic mineralisation during the 1960s. Development within the project area, however, did not commence until Fortescue Metals Group acquired the tenements based on a 2004 agreement, formed a joint venture with interested groups and then initiated an assessment for magnetite (rather than hematite) mining potential. The combined deposits now have an identified large mineral resource inventory, with test work demonstrating they are able to produce a magnetite concentrate of greater than 66 per cent Fe over an extended mine life. This concentrate would be suitable for forming pellets or feed for direct reduced iron products.The deposits form a singular orebody, approximately 12 km in length by 1 km in width and extending to depths beyond 600 m. The four main deposits are geographically separate and have subtle mineralogical differences, thought driven by the degree of deformation and alteration within each area.Definition of the stratigraphy, structure and key mineralogy of the deposits has been carried out through several stages of exploration and project development. This has also included recent mining and processing of more than 1 Mt of feed material to an on-site processing facility. This demonstrated at a production scale that dry plus wet processing techniques can efficiently separate the magnetite from the gangue minerals to form a suitable (marketable) product.Geometallurgical classification of the host stratigraphy has been carried out from analysing the high volume of quantitative data available for this deposit. This has allowed definition of mappable units within the fresh BIF to be used as a driver in mine scheduling, delivering optimal feed to the processing plant.Construction of mine and processing facilities is expected to commence once all technical risks have been addressed, market conditions are deemed appropriate and approval is given by the joint venture partners.CITATION:Simpson, C, 2017. The Iron Bridge magnetite deposits, in Proceedings Iron Ore 2017, pp 287–294 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By G. Ward Wilson

Waste rock and tailings may be combined through intimate blending to create new materials with superior physical and hydraulic properties. The new material, termed Co-Mix, has high shear strength characteristics, low compressibility, low hydraulic conductivity, and a high water retaining capacity. Co-Mixed tailings and waste rock may be used to construct cover systems, internal barriers and seals, confinement structures and full depth waste repositories. Field scale test trials using Co-Mixed blends of waste rock, tailings and slag have been constructed at the Copper Cliff Mine in Sudbury, Canad. These lysimeters will be used to evaluate the performance of the new material for cover systems that may potentially be constructed on the tailings impoundment upon closure. In this sense, the paper point out the construction of the lysimeters with respect to expected field performance during the spring snow melt period and summer to produce cover systems for closure.

Sep 12, 2005

By E. F. Johnson, V. O. Naumann, D. P. Bossler

A method is presented for calculating individual gas and oil or water and oil relative permeabilities from data obtained during a gas drive or a waterflood experiment performed on a linear porous body. The method has been tested and found both rapid and reliable for normal-sized core samples. INTRODUCTION Individual oil and gas or oil and water relative permeabilities are required for a number of reservoir engineering applications. Chief among these is the evaluation of oil displacement under conditions where gravitational effects are significant, such as a water drive or crestal gas injection in a steeply dipping oil reservoir. Numerous proposed methods of obtaining relative permeability data on reservoir core samples have been too tedious and time consuming for practical use, or have yielded questionable and sometimes inconsistent results. A method has been developed by which the individual relative permeability curves can be calculated from data collected during a displacement test. The method is based on sound theoretical considerations. Using this method, with a properly designed experimental procedure, relative permeability curves can be obtained using core samples of normal size (i.e., 2 to 3 in. in length and 1 to 2 in. in diameter) within a few days after receipt of the core. In a recent publication D. A. Efros1 describes an approach to the calculation of individual relative permeabilities that is based on the same theoretical considerations. We believe the approach described in the present paper is more adaptable to practical application than the method implied by Efros. In addition, comparisons with independently determined relative permeabilities are furnished to substantiate the reliability of the new method. DERIVATION Previously the theory of Buckley and Leverett as extended by Welge2 as been used to calculate the ratio of relative permeabilities. In the derivation which follows, this theory is further extended to permit calculation of the individual relative permeabilities. The theory assumes two conditions which must be achieved before the method is applicable. They are that the flow velocity be high enough to achieve what has been termed stabilized displacement,3 and that the flow velocity is constant at all cross sections of the linear porous body. In stabilized displacement the flowing pressure gradient is high compared with the capillary pressure difference between the flowing phases. The high pressure drop insures that the portion of the core in which capillary effects predominate will be compressed to a negligibly small fraction of the total pore space. The assumption of constant flow velocity at all

By Murray Jacobson

Facts obtained by the Bureau of Mines on the dust-explosion hazard in air of materials used in the plastics industry are presented for 313 samples studied in the laboratory. Information is given on ignition temperature of dust clouds and layers, minimum explosive concentration, minimum energy required for ignition, explosion pressure and rates of pressure rise, amount of inert dust required to prevent ignition and flame propagation, and, in some instances, on the limiting oxygen concentration in an atmosphere to prevent ignition by spark and by heated surface. The effects of particle shape, additives, and resin structure on explosibility are discussed. Relative explosibility of the materials is related to the ignition sensitivity and explosion severity and is denoted by an empirical index. Recognition of the degree of hazard will facilitate adoption of adequate measures for preventing ignition and explosion during manufacturing or processing.

Jan 1, 1962

By Sheng-Hui X

This paper introduces a new coal-based rotary kiln process of DRI production - the CRIMM process, which is developed by Changsha Research Institute of Mining and Metallurgy in the past years. Its main features are the use of composite pellets (in rotary kiln). The process consists of preparation of pellets from iron concentrate and coating of coal on their surfaces. The new process is able to overcome a series of defects of the conventional coal-based rotary kiln processes. A continuous test was conducted using an experiment rotary kiln (-0.6;, x 3 m). TFe of the magnetic iron concentrate used in the test is 67.25 per cent. TFe of the product DRI is 88.54 per cent, MFe is 84.11 per cent, S and P are less than 0.02 per cent. The metallisation ratio of pellet is 95 per cent. The pellet power ratio is less than 0.3 per cent. The utilisation coefficient of rotary kiln is 1.3 t/m'-d. The overall recovery of iron concentrates is 99.7 per cent. Two small industrial plants using the CRIMM process are being set up in China. Their coal consumption can be decreased to 520 kg standard coal per ton DRI respectively.

Jan 1, 1999

The association of deep well turbine type pumps with metal mining is by no means a new one, though undoubtedly each application has certain features of interest, conformable with attendant circumstances. Although all conditions pertaining to a particular operation in one mine are rarely, if ever, duplicated in another mine, it is felt that some aspects will be parallel, or in various ways comparable.Therefore the following descriptions of an installation of a deep well turbine pump as part of dewatering plant in connection with shaft sinking may be of general interest to metal mine operators.The Man and Supply shaft at Mount Isa Mines is designed as shown in plan by Fig. 1. It is the main entrance and service shaft for the entire property and hence is in constant use. Arrangements for sinking must be such as to cause little or no impediment to routinehoisting work. Also, being the main shaft, it has been essential to deepen it in step with successive level developments.During the period of operations at Mount Isa only a limited time has been available to complete succeeding levels down to the present No. 7 haulage level (895 ft.), and sinking operations in soft, broken, leached, and heavy water-bearing country have presented many features militating against reasonable speed and cost. Outstanding among these difficulties has been the large volume of water contained in the pervious brecciated country.

Jan 1, 1939