Search Documents

By W. Pariseau, S. Puri, S. Schmelter

Introduction Joints often have profound effects on elastic properties and strength of rock masses and therefore on rock slope stability. In surface mine slopes, joints are usually too numerous to be taken into account individually, so an equivalent properties approach is necessary. Previous work that treats a jointed rock mass as an equivalent composite material of joints and intact rock between resulted in excellent agreement between estimated and true rock mass elastic moduli in case of fully persistent joints (e.g., Pariseau, 1999) Rock mass failure mechanisms on joints and through intact rock were retained obviating the need for an equivalent rock mass strength. Impersistent joints, which are not continuous on a joint plane, can be accommodated (Pariseau, 2003). However, slope stability analysis of a large, deep copper mine indicated a need for computational efficiency even in two-dimensional analysis of vertical sections through pit walls (Puri, 2006). The analyses by the popular finite element method used small elements of bench size near the pit slopes and much larger elements away from the pit walls. The reasons for the graded meshes were numerical quality (small elements) and computational economy (large elements). Small elements contained only a few joints, while the larger elements contained hundreds of joints and led to impractical computation run times (days!). A new modeling procedure that recognizes sufficiently large elements as representative volume elements (REV’s) overcomes this obstacle. A companion improvement recognizes the concept of a representative area element (RAE) in association with joint impersistence and the probability that joint material occupies a considered site. Both are steps towards greater model realism and a practical slope stability analysis procedure. Consider the open pit mine photo shown in Figure 1(a), a companion plan view in Figure 1(b), and the problem of slope stability where high slope angles favor economics but low slope angles favor safety. These competing factors in surface mining generally result in some sections of the mine that have unstable slopes that require monitoring and perhaps mitigating action to improve stability. Although stability of a given section may not be easy to quantify with a single number, useful design guidance can be obtained from a finite element analysis of a proposed mining sequence leading to future pit slopes and profiles. The presence of water from rain and snow melt indicates a need for a coupled analysis that links water pressure, effective stress and total stress (Schmelter, 2001).

Jan 1, 2007

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058°C).

Jan 1, 1972

By P. G. Guest

MANY of the gases and vapors used in anesthesia form explosive mixtures with oxygen or air. Sources of ignition for these mixtures always have existed in operating and anesthetizing areas. When ether was first introduced, candles,5 gaslights, and coal stoves caused fires and mild explosions of the vapor-air mixtures. Today the chief causes of ignition are electrical. Fires and explosions are still much too frequent; and, because many of the mixtures are rich in oxygen, the explosions sometimes are very violent. Obvious sources of ignition, such as electric-power sparks and arcs in open motors, switches, and receptacles, as well as exposed incandescent wires and hot plates, usually are recognized by hospital personnel and corrected. A source of ignition that is not so obvious to many is static electricity. Until quite recently the presence of this hazard in a large majority of anesthetizing areas was not even suspected. However, numerous explosions-many of them fatal to patients-have been attributed, with good reason, to sparks from static electricity.

Jan 1, 1953

By Luke Keeney, Stephen Walters

"The start up of a new mining and metallurgical facility is a crucial step in the life of any mining project. The mining industries record is poor when evaluating processing plant operation relative to design capacity predictions made during feasibility studies. Multivariate geometallurgical orebody characterisation, using principle component analysis, is a method developed for improving predictive processing performance models during feasibility stages of mine development. This paper outlines the application of multivariate geometallurgical characterisation to the Cadia East deposit located in New South Wales, Australia. Cadia East is a low grade high tonnage copper-gold porphyry system in advanced stages of feasibility analysis. A dataset of ~32000 measurements and 150 comminution parameters (A*b and BMWI) has been used to develop class-based characterisation and modelling methodologies. The results of this study outline the development of class-based ore characterisation and provide a technique for analysing and interpreting large and complex geometallurgical datasets for prediction and optimisation of processing performance. The results enable sophisticated population modelling to be conducted which displays deposit scale processing variability, aiding circuit design specifications and predictions during feasibility studies.INTRODUCTIONA feasibility study is the major technical report on which the decision to proceed to production and on which financing is based (Shillabeer & Gypton, 2003). The mining industry’s record is not very good when actual construction time, costs, and operating performance are compared to the projections made in feasibility studies (Ballard, 1983; Gypton & Ward, 2000; Gypton 2002). A study by McNulty (1998) found that of 41 mineral processing and chemical plants built between 1965 and 1995, only 56% achieved design capacity within two years of commissioning and three were closed after failing to achieve design capacity within 36 months of start up (Shillabeer & Gypton, 2003). McNulty (1998) related this underachievement and failure of start up performance to the use of innovative process technology without appreciating and managing technical risk. Factors contributing to technical risk include inadequate pilot plant testing, scaled up prototype equipment without backup, design flaws and poorly understood complex process chemistry."

Jan 1, 2009

By Robert L. Lagace, Michael A. Grossman, Alfred G. Emslie

This supplement to the final report is a collection of interim and monthly reports and working memoranda prepared during the course of this program to document the progress, methods and results of the work. The supplement is divided into the self-contained sections briefly described below. I. SELECTED MONTHLY TECHNICAL LETTER REPORTS - This section is a collection of selected monthly technical letter reports that briefly summarizes the chronological development of the analyses and results, including the different concepts, theoretical approaches, and methods of data reduction and analysis explored, and the discoveries, insights and findings made along the way. More detailed treatments of the key developments and results are presented in the interim reports and working memoranda reproduced in subsequent sections of this supplementary report, and in the separately published final report. II. BACKGROUND THEORY FOR MEASUREMENT PROGRAM ON MEDIUM AND HIGH FREQUENCY RADIO TRANSMISSION IN COAL SEAMS - Working Memorandum - This working memorandum gives the initial background theory needed to guide the planned measurements and data analyses of this program to describe the propagation of radio waves-in coal seams for the frequency range of 50 to 5000 kHz. III. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION - Interim Report - This interim report presents detailed treatments of the data analysis and modelling techniques used, and the associated results obtained from conductor-free area propagation data measured by T. Cory in the first set of six coal mines. The mines were located in three highcoal seams; the Pittsburgh seam in northern West Virginia, the Pocahontas No. 3 seam in Virginia, and the Herrin No. 6 seam in Illinois. IV. ANALYSIS OF MF PROPAGATION DATA FROM MARGARET NO. 11, NANTY GLO, EHRENFELD, AND ADRIAN COAL MINES - Interim Report - This interim report presents detailed treatments of several improved data analysis and Modelling methods applied to, and results obtained from, conductor-free area propagation data measured by T. Cory in the second set of four coal mines. These mines were located in three low-coal seams; the Upper Freeport seam in Pennsylvania and West Virginia and the Lower Freeport and Lower Kittaning seams in Pennsylvania. In addition, this report contains a reprint of two papers presented at a Bureau of Mines sponsored EM Guided Waves in Mine Environments Workshop held in Boulder Colorado. One paper describes the three-layer theoretical model and its application to the conductor-free data from the first six mines, while the second paper describes the theory developed for the coupling of loop antennas to a cable in a mine tunnel in a coal seam, and the model's application to data in the vicinity of cables taken at the Margaret No. 11 mine. V. A METHOD FOR NONINTRUSIVE, IN-SITU MEASUREMENT OF COAL AND ROCK CONDUCTIVITIES IN A COAL MINE TUNNEL - Working Memorandum - This working memorandum briefly describes a possible direct method, and its potential advantages and shortcomings, for performing in-situ measurements of coal and rock conductivities. VI. MODELLING AND DATA ANALYSIS OF IN-MINE ELECTROMAGNETIC WAVE PROPAGATION FROM 50 to 5000 kHz - Interim Report - This interim report presents a summary comparison of theoretical and experimental results for conductor- free areas in eleven coal mines located in seven coal seams. It also summarizes the findings and their implications for intrinsically-safe, portable radio communications between roving miners.

Jan 2, 1980

By G. Kim

The influence of bacterial growth phase on the flotation behavior of malachite has been investigated in a well-controlled Hallimond tube system. The microflotation tests were conducted for malachite (45?53 µm) using different amounts (bulk phase concentration=1×108?5×109 cells/mL) of Rhodococcus opacus (R. opacus) as a collector, which was grown at mid-exponential versus stationary phase, at a constant speed (340 rpm), pH (6), and malachite-bacteria interaction and flotation time (each 10 min). Hug differences between R. opacus cells in mid-exponential and stationary phase was observed from the results for electrophoretic mobility and flotation tests. Specifically, the isoelectric point of the cells in the stationary phase was lower than that in the mid-exponential phase, suggesting that the amount and distribution of surface functional groups onto cell surfaces are likely different. Additionally, the cells in stationary phase led to significant increase in the flotability compared to those in mid-exponential phase over the background bacterial concentration level of 1×108?5×109 cells/mL. Furthermore, the flotation efficiency tended to increase with increasing cell dosage for stationary phase cells while no distinct difference was observed for mid-exponential cells.

Feb 27, 2013

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

This paper discusses the history and development of the system and the benefits that are being gained for Yabulu from Solar Drying. Following the end of mining of the local Greenvale and Brolga nickel deposits, QNI Yabulu Refinery is dependent upon imported ore from over 15 different mines in New Caledonia, Indonesia and the Philippines.

Jan 1, 2003

By Ron Frye, Carl Liibbe, Wayne Curtis, Julie Pecori, Dan Leach

Test work comparing the performance of a Low Density Porous Ammonium Nitrate Prill to regular Porous Ammonium Nitrate conducted in Pennsylvania and New York showed that less ammonium nitrate was required to perform the same work and that improved sensitization of an emulsion/ammonium nitrate blend reduced “orange fumes”. Fragmentation was similar in all tests with improved heave and throw experienced.

Jan 1, 1997

The tenth annual Mine Resale Evaluation was held in conjunction with the RMCMI 2001 convention at the Steamboat Springs Sheraton Resort, Steamboat Springs, Colorado June 23 through 26. The purpose of the mine rescue evaluation program is to provide an opportunity for mine rescue teams to learn new skills and improve their existing ones in a non-competitive environment. Several staged ?disaster? scenarios were held where the teams are called upon to exhibit their life saving abilities. The evaluators meanwhile are offering suggestions, both verbal and written, to help the teams better understand the situations presented them. This non-competitive environment allows the teams to work together and share their knowledge with fellow mine rescue teams providing everyone with a positive learning experience. Mine Rescue Chairman Bill Balaz, Balaz & Associates, was in charge of coordinating the events. Six teams consisting of seven to twelve members each (totaling 60 members) participated in the three-day event. Each ream was required to respond to direr different real-life scenarios plus a written general knowledge test daily. Cindy Burnham has assisted Bali, for a few years. Her responsibilities include grading all of the written tests. This year's tour professional evaluators included Art Seanz (Hazardous Ma¬terials) of Western Environmental Associates ; Guy Norton (Ropes), Guy Horton Rope Rescue; Mary Bailey (Medical), MBA Training and Morley Hense (Confined Space). Carolyn Durga, BHP Coal, also assisted in hazardous materials and medical scenarios. They each provided three different challenging mock situations per day per team. The teams had no prior knowledge of what the scenarios would be as details were provided only as they arrived. Ten volunteer victims added much drama and excitement to the event. Their realistic enactment, complete with false blood makeup and severed limbs, made for some very tense scenarios. The Mine Rescue Teams participating this year were BHP LaPlata, BHP Navjo, BHP San Juan, all from Farmington, New Mexico; Bridger Coal Co., Rock Springs, Wyoming; Sabine Mining, Longview, Texas; Solway Minerals, Green River, Wyoming and Western Energy Co., Colstrip, Montana. Many new friendships were made and much knowledge shared. A swap meet was held Saturday afternoon for the teams to exchange miscellaneous equipment, hats, shirts, etc. The trams were asked to evaluate the program and the evaluators. They responded with many positive suggestions that will help improve the upcoming events in the years to come. Culmination of the Mine Rescue program was a Tuesday morning awards breakfast where the teams were presented with trophies. Each member was also given a gold pin with the words Continuing Challenge - Ropes.' The pin was the first in a series that will be given over the next few years. The participating victims and evaluators were also commended for their outstanding efforts. Special signed "Victim" shirts were given to select volunteers. Sponsors for the Mine Rescue program were Flanders Electric Motors, Magnum Metals, Rocky Mountain Electric Motors, Sedona Consulting and Balaz & Associates. Many hours of volunteer tine and effort from various family members of participants helped make the 2001 event a huge success.

Jan 1, 2001

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By Alton Gabriel

During the fall of 1940, J. R. Thoenen of the Mining Division, Bureau of Mines, accompanied by the senior author, surveyed the more important domestic alunite deposits. Although the study was designed primarily as an economic survey, samples from a number of the deposits were collected to investigate the beneficiation of the lower-grade material.

Jan 1, 1942

By B. G. Tarasov

This paper proposes the further development of a recently identified shear rupture mechanism (fan mechanism) that elucidates a paradoxical feature of hard rocks ? the possibility of shear rupture propagation through a highly confined intact rock mass at shear stresses that can be significantly less than frictional strength. In the fan mechanism, failure is associated with consecutive creation of small slabs (known as ?domino blocks?) from the intact rock in the rupture tip, driven by a fan-shaped domino structure representing the rupture head. The fan head combines such unique features as extremely low shear resistance, self-sustaining stress intensification, and self-unbalancing conditions. Consequently, the failure process caused by the mechanism is inevitably spontaneous and violent. Physical and mathematical models explain unique and paradoxical features of the mechanism, which can be generated in primary ruptures and segmented faults. The fan mechanism provides a novel point of view for understanding the nature of spontaneous failure processes, including shear rupture rockbursts. The process explains, in particular, features of shear rupture rockbursts such as activation at great depths, generation of new shear ruptures in intact rock mass, nucleation of hypocentres at significant distances from the excavation, shear rupture development at low shear stresses, and abnormal rupture violence.

Jan 1, 2014

By Bryn Harris, Liming Huang, Andre Laplante

"This paper reviews flowsheets generally used in gold rooms to upgrade primary gravity concentrates particularly those of Knelsons. It is concluded that even for small operations, which treat between 250 and lo00 kg of concentrates per day, there is a strong economic incentive to include in the flowsheet magnetic removal of tramp iron, at least two shaking tables, screening of either table feed or table tails at 150-212 um, and scavenging of table tails with a small centrifuge. Headroom, rather than floor space, is often inadequate in most gold room designs, and limits gravity flow and flowsheet flexibility. Experimental data are presented to demonstrate the effectiveness of a small Knelson Concentrator to scavenge significant amounts of gold (up to 91 %) from fine table tails.RésuméCet article examine les schémas d’évolution généralement utilisés pour traiter les concentres gravimétriques d‘or, en particulier ceux produits par concentrateur Knelson. Nous en venons à la conclusion que même pour un petit circuit d’une capacité de 250 A 1000 kg/jour pourrait bénéficier des opérations unitaires suivantes : concentrateur magnétique pour extraire la feraille, au moins deux tables A secousses, criblage de l’alimentation ou du rejet d’une ou des tables i une maille de 150-212 um, et épuisages des rejets fins de table avec un centrifuge de petite capacité. C’est l’espace vertical du lieu où se fait cette concentration qui représente la contrainte la plus importante, plutôt que sa surface, puisqu’il faut maximiser l’écoulement par gravite des pulpes et s’offrir une certaine flexibilité quant à l’agencement final des opérations unitaires. Nous présentons également des données expérimentales pour démontrer l’efficacit6 d‘un Knelson de laboratoire pour récupérer jusqu’ à 91 % de l’or contenu dans les rejets fins de table."

Jan 1, 1999

By Joan T. May

Federal Bureau of Mines studies showed that some organic amine hydrochlorides can be used as dehydrating agents for producing anhydrous magnesium chloride from hydrates and brines. Laboratory-scale tests showed that double salts are formed by reacting 35 percent magnesium chloride brine or spray-dried magnesium chloride with pyridine hydrochloride. Heating decomposed these double salts to anhydrous magnesium chloride and recycle pyridine hydrochloride. Pyridine hydrochloride also chlorinated any magnesium oxide in the spray-dried magnesium chloride. The anhydrous magnesium chloride obtained by the method described contained less than 0.8 percent oxygen. More than 98 percent of the organic amine hydrochloride was recovered.

Jan 1, 1978

By C. J. H. Steenkamp

Theoretically, the main driver behind a mining operations? sourcing decision should differ from company to company, and within a company from project to project, but in reality it often relates to cost. Research confirms that there are a number of factors, including cost, to consider when choosing between in-house and outsourced mining. While the literature is rife with factors to consider, little information exists on how to apply these in practice and the relative importance of the different factors to be considered. A study was conducted to determine whether mining is truly a core competency for a mid-tier commodity specialist mining company. Furthermore, a decision-making framework for mining operations sourcing was developed, and the critical success factors that should be adhered to if outsourced mining is chosen were determined. The research showed that owner mining is not a core competency for the mining company investigated. A decision-making framework was developed using the order winner/order qualifier structure, which can be used to facilitate the mining sourcing decision. The most important tools at the disposal of a mine owner?s team to manage a contractor miner are the social and output control mechanisms, according to the critical success factors study.

Jan 1, 2014

By C. Deutsch

Resource estimation for the West Leeville deposit is prepared using a conventional explicit approach. The geologic model is developed using interpretive methods based on visual logging. Grade shells are then prepared at low and high grade cutoffs. The low grade shell includes material of interest (Au > 0.010opt), while the high grade shell is developed slightly below the economic cutoff grade for mining. Grade estimates are made within these boundaries. This paper documents a conditional simulation study to evaluate the uncertainty contributed by both the grade shells and grade estimates. Multiple realizations are generated for the grade shells and the grades. The full combinatorial of realizations are merged to assess the uncertainty and the relative contribution of the grade shell and grades.

Jan 1, 2007

Apparently there is little inclination on the part of mining engineers to supplant the transmission of power by compressed air with it's formidable rival, electrical transmission. No doubt there are many advantages to be claimed for compressed air that render it parculiary well suited for the conditions which characterise underground work.

Jan 1, 1902

By William E. Souder

The behavioral accident simulator (BAS) is a computer program that can be used to simulate accident situations. It demonstrates how the potential to have an accident grows or diminishes as a result of changes in various environmental, organizational, and behavioral factors. It calculates the number of fatalities that may result from various conditions and graphically displays these data. The BAS is useful for studying systems of accident causes, for demonstrating the various ways to diminish fatalities, and for training employees. This Bureau of Mines report provides the detailed instructions needed to use the BAS.

Jan 1, 1988

By Jim Baumann

Deposited millions of years ago in irregular paleokarstic channels, Jamaica’s extensive bauxite deposits provide good quality ore for alumina production and subsequent aluminum smelting. Bauxite mining operations are critical to the Jamaican economy. It accounts for a large percentage of Jamaica’s export earnings. Bauxite production in Jamaica accounts for about 10% of the world’s output each year. Bauxite deposits in Jamaica lie close to the surface. They can be extracted using standard surface mining techniques. The deposits occur in scattered pockets across the country’s rugged landscape. So it was necessary for two of the country’s major mining and refining operations to implement cost effective methods for the acquisition and management of bauxite reserves and surface ownership distribution rights.

Jan 1, 2002