Search Documents

By Don Rose

INTRODUCTION A number of tunnels supported and permanently lined by steel-fiber-reinforced shotcrete (SFRS) have been built in North America in the 1980s. The material is more economical than, and technically equal or superior to, conventional shotcrete using wire mesh. The design and construction of SFRS-lined tunnels is straightforward, and only a few new design principles, laboratory tests or construction equipment modifications appear necessary in order to use this material. Modern tunnel Contractors may use cyclic drill-and-blast methods on some tunnels, with intermittent shotcreting as part of an orderly cycle. The Dry Mix method is most suitable for cyclic, intermittent, relatively small-scale shotcreting. However, modern Contractors excavating tunnels continuously using large long Tunnel Boring Machines (TBMs) or Roadheaders may prefer Wet Mix shotcreting on a mass production basis. In either case, the use of steel-fiber-rein¬forced shotcrete (SFRS) promotes the rapid and economical excavation of tunnels. The addition of microsilica will improve SFRS properties and reduce rebound, and is expected to become standard practice with SFRS in North America, as it now is in Scandinavia. HISTORICAL REVIEW Steel-fiber-reinforced shotcrete (SFRS) at the present time (1985) is essentially conventional shotcrete with straight or deformed steel fibers added, and in general SFRS for tunnel linings encounters the same problems that conventional shotcrete does. Shotcrete history is well known. The use of sprayed plaster on wire frames for mounting animal skins by Carl Akeley of the Smithsonian

Jan 1, 1985

By Juan Carlos Salas

In this paper, a collaborative R&D model which has been successfully applied by a global mining companies association is presented and analysed both from the conceptual and practical point of view and an example of these collaborative initiatives, the Copper Technology Roadmap recently generated by a group of the most relevant copper mining companies, is presented, including an analysis of strategic opportunities and challenges in the Latin American region.

Sep 9, 2007

By W. R. Hibbard

Evidence is presented which confirms previous findings that models of solution strengthening depending solely on lattice parameter changes are incomplete. Direct evidence for the Suzuki interaction of chemical effects was obtained from alloys with constant lattice parameter, for which solution strengthening was nearly independent of temperature from 300° to 20°K. SOLUTION hardening principles have been reviewed recently by Parker and Hazlett.' In addition, the interactions of dislocations and solute atoms were reviewed by Cottrell.' It is not proposed to review this information again here, but to refer only to those details which are pertinent to the developments which have occurred since these papers were published. Literature Survey To set the stage, it has been known for some time that solid solutions are stronger than the pure parent metals, and that the strength increases with increasing amounts of alloying element. One of the most extensive earlier investigations was that of Lacy and Gensamer,3 who reported that the solid solution strengthening of iron is a power function of the composition, that the relative strengthening is a function of the solubility limit, and that the rate of strain hardening is a function of the amount of solution hardening. Thus, the slope of the plastic portion of the stress-strain curve increases with increasing yield strength. An approach to the development of principles resulted from work by Gulyeav,4 who reported that the strengthening effect of solid solution alloys is periodic in character when plotted as a function of the atomic number of the solute. A more quantitative approach was to relate the amount of solution hardening to the lattice parameter of a solid solution. This was done quite early by Norbury,5 and later by Brick, Martin, and Angier,6 Frye and Hume-Rothery,7 and French and Hibbard. This relationship is only approximate in character. The next development was to relate the amount of solution hardening to lattice stress, as proposed by Frye and co-workers.9 They calculated what they called ionic overlap from the lattice parameter changes represented as a change in volume, using Bridgman's hydrostatic compression equation. The resulting correlation was somewhat improved as compared to the simple correlation with lattice parameter. The next step was carried out by Dorn, Pietrow-sky, and Tietz,10 who suggested an effect of valence differences in addition to the effect of lattice parameter. Their proposed parameter shows flow stress as a single valued function of the concentration and a relationship involving these two atomic variables. In addition, they contributed new data on the temperature dependence of solution hardening which indicated that it was a strong function of temperature for aluminum alloys. Allen, Schofield, and Tate11 carried the valency effect even further by reporting data indicating that with a given solvent element the stress-strain curve is a function of electron density, entirely neglecting the size factor, which varied by a factor of two. This evidence led to a quantum mechanical calculation by Cottrell, Hunter, and Nabarro,12 based on the formation of a dipole around an edge disloca-

Jan 1, 1959

Except for uranium search, conventional oil well logging techniques are relatively little-used in mining exploration. The main reasons for this are cost and an apparent lack of awareness of the potential use of the methods in the search for ore. However, relatively inexpensive portable units are currently available for performing the simpler electrical and radiometric logs in diamond drill holes.The emphasis in oil exploration logging programmes is largely on the estimation of porosity. In most mineral work, however, porosity is not very significant, and factors such as mineral conductivity and radioactivity assume an important role.The Bureau of Mineral Resources (BMR) during a programme to explore for uranium and associated base metals in the area east of Rum Jungle, N.T., carried out electrical and radiometric logging of diamond drill holes as a routine part of their investigations. Case histories are described in which the logs were used to aid in defining stratigraphic sequences and transgressive structures in base-metal prospects. Some surface geophysicalanomalies were explained by the logging: induced polarization and electromagnetic anomalies were related to black slate; and self-potential anomalies were related to oxidation of pyrite black slate, or apparent electrokineticeffects in the black slate. The logs provided an objective appraisal of the rock units penetrated and thereby helped to differentiate lithologies.Borehole logging, including newer techniques such as downhole analysis, could be done in geological and geophysical investigations in other areas for a relatively small cost with a considerable potential gain of information.

Jan 1, 1978

Coal has been mined in the central Appalachian coalfields of southern West Virginia, western Virginia, and eastern Kentucky for more than a century. The dwindling reserve base consists in large part of coal that would have been considered unmineable by earlier generations. Nearly every current operation is working on a property where coal has been extracted in the past, from seams either above, below, or both. NIOSH is conducting research aimed at helping mine planners prevent hazardous conditions due to multiple seam interactions. To-date, more than 300 case histories have been collected from underground mines, mainly from central Appalachia. This paper focuses on several of the more challenging situations that have been encountered, including: • Room-and-pillar development 20 ft (6 m) beneath full extraction workings at a depth of 1,000 ft (300m) of cover (Virginia) • Pillar recovery 45 ft above full extraction workings at 900 ft (270 m) of cover (Virginia) • Near-simultaneous room-and-pillar mining with pillar recovery with 40 ft (12 m) of interburden and 1,500-2,000 ft (450-600 m) of cover (Kentucky) • Longwall mining directly beneath main entries in overlying seams (West Virginia) • Some of these operations have been highly successful in overcoming the challenges, others less so. The lessons learned from their experience will help ensure that these and similar difficult reserves can be mined safely.

By James A. McGrath

"The predominant key word associated with all commercial blasting methods is “safety”. Safetyshould take precedent over all other aspects of the entire explosives industry which on a wholehas had an excellent track record as to number of injuries per unit of hours worked at all blastsites throughout our country."

Jan 1, 1999

By Paul-Dominique Oudenne

For many years, CMI NESA has gained considerable experience in the field of alternative thermal processing processes by which useful by products result in addition to the destruction of the raw wastes. The CMI NESA pyrolysis process has been extensively applied to a wide range of sewage, industrial sludge and residues. This paper describes in details the development works carried out at the pilot stage as well as the key parameters of the process. Some of the industrial realisations are briefly described, the most recent one being the erection of a sludge pyrolyser on predried sludge at 90% dryness of a capacity of 100 tons of dry matter per day for the Valenton plant of the SIAAP (city of Paris).

Jan 1, 2006

The Cowarra gold mine is at latitude 36°O'S. and longitude 149°19'E. which is roughly 20 miles north-north-east of Cooma.The deposit was· originally worked towards the end of the last century, but the presence of sulphides associated with the gold in the primary zone caused cessation of work when that zone was reached.GEOLOGY AND MINERALIZATIONThe principal country rocks are sandstones and shales of Silurian and Ordovician age, both very strongly folded with structural pitches ranging from a few degrees to almost vertical. The mine proper is within Silurian rocks and the main orebody (there are several minor parallel bodies) is developed within a shear striking approximately north, dipping approximately 70° east, and ranging in width from 2 ft to 15 ft but averaging about 4 ft.This shear is impregnated with quartz and sulphides with which the gold is associated. The predominant sulphide is pyrite though pyrrhotite is commonly present in quantity.Arsenopyrite and bornite are present in smaller amounts.Stillwell (1936, 1937a, 1937b, 1938, 1941) has published five mineragraphic reports on the ore.The various levels have been mapped in detail (Figs. 1-3) and the No. 2 level plan (Fig. 1) shows the general relationship of shearing, as now indicated by mineralization, and faulting. There is no apparent connection between the fold structures and mineralization.Fig. 3 is a longitudinal projection showing the distribution of gold expressed as inch-ounces. The estimation of...

Jan 1, 1965

By R J. Johnson

The development of "SANFO" has provided the Mining Industry with a LOW COST HIGH GAS VOLUME, VARIABLE DENSITY, Blasting Agent which can be blended "On Site" in a simple Agitator mixing and charging system by mine site employees.

Jan 1, 1996

By John Addison

Experimental animal studies comparing asbestos and non-asbestos varieties of tremolite indicate tremolite asbestos is markedly more carcinogenic. By direct analogy, the differences in carcinogenicity between tremolite asbestos and non-asbestos prismatic tremolite should be the same for the other types of amphibole that also crystallize in the asbestos and non-asbestos habits. The earliest of the experiment animal studies, done more than 25 years ago, have design limitations by modern standards including the use of injection or surgical implantation as the route of administration rather than the more relevant route of inhalation. However, the differences in the carcinogenicity of amphibole asbestos and non-asbestos amphiboles are sufficiently large to be clearly discernable even with the study limitations. Together with later studies on these and related minerals, there is strong evidence of a much lower hazard associated with the shorter, thicker fibers of the non-asbestos amphiboles, than is found for the asbestos analogues of the same mineral. It is possible that the non-asbestos amphiboles are no more hazardous than other silicate minerals widely considered nuisance dusts. © 2007 Elsevier Inc. All rights reserved. Keywords: Amphibole; Asbestos; Tremolite; Carcinogenic

Jan 1, 2007

By Gary L. Seider

Helical screw piles are used in various applications including the underpinning of distressed foundations and as deep foundations for new structures. At present, maximum design loads range between 12.5 and 50 tons. Helical piles installed with in-situ grouting of the central steel shaft are a relatively new type of deep foundation, which have extended the present maximum design loads to the 100-ton range. Vickars & Clemence discussed this new foundation system in a paper presented at GEO-Denver 2000 in Denver, CO. Over the past three years, grouted shaft helicals have been used successfully on remedial and new construction projects all across North America. The authors have studied several construction projects in a variety of soil conditions to compile a list of practical design guidelines. Those guidelines include installability of grouted shaft helicals based on soil type, equipment requirements, grout selection, and theoretical vs. actual load capacity. In a number of cases, full-scale, field load tests were conducted in both granular and cohesive soils and the results broken down between tip resistance on the helix bearing plates and friction resistance on the grouted shaft. Data is presented which will further efforts to develop a design model and method to accurately predict the axial and lateral capacity of grouted shaft helicals.

Jan 1, 2003

By M. Li, J. D. Miller

Many technology problems must be solved if we are to continue to produce phosphate at our current rate of consumption. The U.S. produces at least 25% of the world's phosphate, 40 million tons of phosphate rock per annum with most of the production coming from Florida. Of particular concern are improved separation efficiency and the ability to treat new dolomitic resources. Phosphate flotation technology needs include: 1. Simplification of the standard flowsheet 2. Improved recovery of coarse phosphate 3. Selective flotation for phosphate recovery from dolomitic resources Preliminary results, including tests on plant feed from Florida show that these objectives may be achieved with a new collector chemistry depending on the specific circumstances. The effectiveness of the new collector chemistry has been demonstrated by the preliminary results from single stage flotation experiments both at the University of Utah laboratories and at Florida Institute of Phosphate Research (FIPR) laboratories. In the best case, from these experiments with low grade (5% P2O5) coarse feed (16x35 mesh), a single stage phosphate recovery of 95 % was achieved with a concentrate grade of 31 % P2O5. Such a separation efficiency could not be achieved using the traditional fatty acid/fuel oil collector. Based on these results it seems that a one step process may be possible for phosphate flotation and a research program is justified for the development of this new flotation strategy.

Jan 1, 2001

By S. C. Sun

Pennsylvania has ample reserves of high-alumina clays which are potential sources of alumina, but many of these clays contain large amounts of iron, which makes them unsuitable for treatment by acid processes(1). The purpose of this investigation was to determine the optimum conditions for the selective hydrochloric acid leaching of iron (2-4) prior to the sulfuric acid extraction of alumina from Pennsylvania ferruginous high-alumina clays. This was accomplished by first testing the iron-bearing minerals and the clay minerals most often encountered in Pennsylvania clays to determine their rate of dissolution in hydrochloric acid solutions. The results of individual minerals were then based for leaching Pennsylvania clays with a 19% hydrochloric acid solution at the boiling point of the acid for approximately 30 minutes to achieve as high as 90% iron removal and only 2-5% alumina losses.

Jan 1, 1968

By Pr-Anders Persson

This chapter deals with the concepts of shock waves and detonation waves together, because a detonation wave is really a shock wave, supported by the explosive reaction that the shock wave ignites and propagates as it travels through the explosive material. In the c.ootext of rock blasting, furthermore, there is justification for treating shock waves and detonation waves together, because the mechanical effect of the detonation in an explosive in a drillhole in rock is propagated and its effects are spread throughout the surrounding rock by means of a shock wave. The overall performance of sn explosive in rock blasting or any other application is of course dependent on how much thermal energy is released in the chemical reaction that occurs when the material detonates, and on how much useful mechanical work the reaction products can do as they expand. A major portion of this chapter deals with the prediction and measurement of explosive performance, a subject which is now still in a process of rapid development.

Jan 1, 1995

By W. L. Barry

A review of the practices of analyzing for precious metals at the Reno Research Center, U.S. Bureau of mines, is presented. A general description of fire assaying, the physical layout of a fire assay laboratory, and the use of fire assaying in combination with atomic absorption, induction coupled plasma, and emission spectroscopy is reviewed. The combination of techniques significantly decreases the detection limits for precious metal analyses and simplifies the analysis of the platinum-group metals. Methods of protecting personnel from ingestion of lead are also discussed.

Jan 1, 1982

By K. Lang

A case study is provided that highlights the successful use of high efficiency electrical submersible pumps (ESPs) adapted from the oil and gas industry for a large scale, open pit mine dewatering operation. In this case, the mine is Goldcorp?s Peñasquito Mine, Peñasco and Chile Colorado open pit development areas in Zacatecas, Mexico. At the time of publication (July 2012), there were 18 vertical bedrock dewatering wells producing an average flow rate of 350 liters per second (lps) from the Peñasco and Chile Colorado development areas. Average pumping rate per well was 18 lps, with a maximum of 44 lps. The depth of wells varies from 330 m to 500m, and includes both in-pit and perimeter (ex-pit) pumping centers. A network of 50 piezometers was used to monitor the response of groundwater levels to pumping. Since dewatering operations were initiated in 2007, groundwater elevations decreased overall, from approximately 1950 m above sea level (masl) to around 1625 masl, for a total of 340 m of drawdown. The pit floor elevation was approximately 1655 masl. All of the producing wells were constructed with 16-inch boreholes, completed with 10-inch diameter blank casing and louvered screen sections and equipped with ESPs. The application of ESPs has proven to be highly effective in the case of Peñasquito?s dewatering operations. Noted advantages include the following: ? Small diameter pump allows use of smaller diameter boreholes (16 inches) and casing / screens (10 inches) reducing well drilling and construction costs ? Greater application range for flow rate and total dynamic head ? Variable speed drive systems for greater energy efficiency and flow rate optimization ? Integration of downhole instrumentation into the motor and pump assembly The advantages and benefits of using high efficiency ESPs revolutionized the dewatering program at Peñasquito open pit mine as evidenced by the number of deep vertical well installations and high dewatering flow rates and total dynamic head requirements.

Feb 27, 2013

By Steven Norris, William Moler, Michael Cole, Patrick Doig, Debi Lewis, Craig Pyle, Matthew Crow

The recently completed Lower Northwest Interceptor Program (LNWI) in Sacramento, California comprises, ten pairs of micro tunnels totaling 4,369 m (14,417 ft),three horizontal directionally drilled bores totaling 956 m (3,154 ft), and two large diameter tunnels under the Sacramento River totaling 1,198 m (3,953 ft). This paper briefly summarizes surface and subsurface conditions, and planning and design considerations. It then goes on to describe problems encounterd with each trenchless crossing, as well as lessons learned with respect to shaft construction, ground control at shafts during tunnel break-in and break-out, frac-out and heave, settlement, obstructions, coordination with permitting agencies, and application of geotechnical baseline reports.

Jan 1, 2007

A clear understanding of the meanings of terms is important when discussing a project. Whether it is a submission, an investment study, a feasibility study, an environmental impact statement, an estimate, a tender, a contract, or a close-out.report, the need for all parties involved to understand what is under discussion or what has been written is paramount. The clarity of definition and the level of understanding can affect the outcome of the project. It is vital that all parties know what is wanted, what is expected, and what it will cost. This paper draws attention to some of the problems that beset many projects, clients, project managers and contractors, and it is hoped that its presentation will encourage us to pay more attention to defining what it is that is required. Ultimately we should all be the richer for having defined and understood the requirements at the beginning rather than at the end.

Jan 1, 1990

By John C. Nigro

This Bureau of Mines report summarizes the performance characteristics of a 30-day around-the-clock gasification-pelletizing test conducted in October and November of 1980 with North Dakota Indianhead lignite. Gasification was conducted in a commercial-size, 6.5-it-diam, Single-stage, fixed-bed, atmospheric pressure producer with a rated capacity of about 30 million Btu/hr. Iron oxide pellets made from a commercial hematite concentrate were fired with the low-Btu gas in a 2.8-ft-diam by 35-ft-long pilot plant rotary kiln at a rate of 900 lb of pellets per hour. Gasifier operations at fuel feed rates up to 3 tons of lignite per hour and hematite pellet induration with raw 160-Btu/std ft3 lignite gas are described.

Jan 1, 1982

By Stefan Larsson, Sebastian Adevik, Sadek Baker, Razvan Ignat

"Abstract Uncertain strength, deformation and flow properties in dry deep mixing columns often lead to conservative choices concerning design values where the design is regularly complemented with a surcharge fill. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle. The deformation properties of a ground improvement were studied by means of two small embankment load tests. The settlement measurements were also used in FEM analyses, where the effect of surcharge on creep settlements was investigated. Based on the results, the effects of the surcharge were considered negligible and could safely be ignored. The project is an example how the contractor can use a field test as an effective design approach.IntroductionGround improvement of soft soils with dry deep mixing columns, or lime-cement columns, is often combined with a surcharge fill. The main reason for using a surcharge is to force the primary settlement and some of the secondary settlement that would have occurred under the final embankment height alone, to take place under the surcharge loading. Another reason is to level out uneven settlements. Strength and deformation properties in improved soil cannot be sufficiently assessed in advance, before columns have been tested on-site, and this uncertainty often lead to conservative choices concerning design values. In order to compensate for a slow forecasted consolidation process, the design is regularly complemented with a surcharge. The surcharge not only leads to increased cost but also to logistical problems where the surcharge is a physical obstacle.Extensive research undertaken by Åhnberg (2006, 2007) shows, by means of triaxial and oedometer tests, that cementation processes and a load acting on the columns during hardening, makes the improved soil to behave as a heavily over-consolidated soil due to an increase in quasi pre-consolidation pressure. The effects of using a surcharge on the time for consolidation and creep properties are thus probably small, since the stress level does not normally exceed this quasi pre-consolidation pressure. A study presented by Venda Oliveira et al. (2013) shows that the stress level within small ranges has limited effect on the creep properties.This paper presents a case study where the deformation properties of a ground improvement using dry deep mixing columns was investigated by load tests on two small test embankments. The tests were performed at the Interchange Värtan project site, which is part of the Norra länken infrastructure project in Stockholm. The tests were not performed as a research project but simple load tests performed by the contractor with the purpose of rationalizing the design delivered by the client. One purpose of the load tests was to assess the deformations when the columns are loaded temporarily by overlaying concrete works. Another purpose was to provide some input data to a study of the effects of using surcharge on creep settlements. The analysis was conducted as finite element modeling using the commercial code PLAXIS, where creep settlements can be simulated using the built-in Soft Soil Creep model."

Jan 1, 2014