Search Documents

By E. Gybbon Spilsbury

(Pittsburg meeting, March, 1910.) THE recovery of gold and silver from their ores by means of the cyanide process has been so successful in the last few years that any radical improvement would seem impossible; yet the appliance to which I wish to call attention in this paper is really a radical departure from the methods now in general use. The most modern and approved of these, known as the all-sliming method, depends for its success on the grinding of the. ore so fine that practically 90 per cent. of it will pass through a 200-mesh screen. The slimes thus produced are then agitated and aerated in tanks of various types. The main object of this treatment is to insure such a thorough admixture of the pulp and solution that every particle of the ore is surrounded by a volume of solution sufficient to insure the dissolving of the whole of the gold- and silver-content. In addition, in order to expedite the action of the cyanide, and to oxidize such elements as would, if left in their active state, become cyanicides, air is blown in under pressure. In the Pachuca tank, this air is the active and sole means of agitation. The chief objections to all the methods off agitation used heretofore are the expense of operating and maintaining the mechanical devices for keeping the pulp in suspension, and the length of time required to obtain a fairly complete extraction. of the values. These objections are inherent to any method of agitation effecting a circulation of the pulp and the solution together, by giving the whole mass a circular movement, as in the low-tank system, or a vertical circulation, as in the Pachuca-tank system. In both methods, the particles of ore are kept traveling in the same direction as the solution, and with very little difference of speed; so that, while the whole mass is in

May 1, 1910

By N. Hadebe, A. Mampuru, F. Jantjies

Mintek conducted test work to study the effect of media wear when using Mintek’s Milling-in-raffinate technology. The grinding media consisted of high-chrome and ceramic balls. The tests were conducted using a laboratory 5L 316 stainless-steel rubber-lined mill. Magotteaux supplied the high-chrome and ceramic balls. The raffinate was synthetically prepared using a typical Cu/Co (2.2 g/L Cu, 3 g/L Co) composition. The milling rate, media wear, mill, leach extraction efficiencies, gangue acid consumption, and residence time were studied. The tests indicated that the high-chrome balls had a higher corrosion rate than the ceramic balls. The ceramic corrosion rate was lower than 0.1 mm/y. The highchrome balls performed better during the leach stages with faster milling time, higher leaching efficiencies for both Cu and Co, lower gangue-acid consumption, and lower residence time

Jan 1, 2023

By W. T. Isbell

Although the pressure to meet the heavy demand for lead still took precedence over new metallurgical developments in the field of roasting, smelting, and refining of lead in 1948 there nevertheless has been considerable activity in the experimental development of new processes and improvements as well as plans for the modernization of many plants both here and abroad. Increasing labor and material costs have stimulated the trend to greater mechanization, revamping of flow sheets, and construction of larger units wherever possible. Although there have been many serious labor stoppages in the United States, Mexico, and Europe, labor supply has improved in most plants even if it has fallen off in efficiency.

Jan 1, 1949

By KOKOWSKI J., RUDZIŃSKI Ł.

The LUMINEOS network was established in 2013 to monitor mining-induced seismicity in Legnica-Głogów Copper District (LGCD), located in south-western Poland. Since the starting time, the network was improved and today consists of 17 seismometers and 10 accelerometers. Up to now, the strongest recorded earthquake in the region had Mw4.0. Both raw seismic data and earthquakes catalog for events recorded by the LUMINEOS network are fully open and available on the EPISODES platform (https://tcs.ah-epos.eu/#episode:LGCD). During the last 7 years, the network improvements gave us a possibility to increase location accuracy for shallow mining events. This accuracy is influenced by factors such as the configuration of seismic stations, noise level at seismic stations, and the influence of the velocity model. Here we encountered two main issues which are worth to discuss. The first one is the low detection threshold of two seismic stations and their significant impact on the location errors. The second one is the large uncertainty in the S-wave picking. Even though S-waves are not so clearly visible on seismograms, they are very helpful in the estimation of source location and strength of seismic events in the region. In our work, we present the history of LUMINEOS network and corresponding improvement on location accuracy as well as the influence of noisy stations on the error distribution and how it is connected with location results. We also investigate the effect of the S-wave phases and how they are related to the accuracy of the earthquakes locations in the network.

Apr 26, 2022

By P. Ramsaywok, G. Legodi

Spiral concentrators are widely used in the coal industry treating fine (-1mm) coal. Their application was a limitation to the product quality until the introduction of low-cut spirals which allow a lower quality ash product to be produced, thus expanding the market. The Exxaro Grootegeluk 1 (GG1) plant has a two-stage traditional rougher-cleaner spiral circuit using conventional SX4 spirals to produce semi-soft coking coal product at 12.5% ash by mass. The overall plant product is 10.3% ash meaning that the coarser sized coal dense medium separation circuits must compensate. A low density cut-point spiral targetting 10.3% ash would thus be beneficial to the overall complex. The spirals were tested in the two-stage plant environment and in a pilot plant. This paper discusses the findings and compares a two stage four-turn low density cut and conventional spiral. The two spiral technologies were unable to sustain a 10.3% ash product. Pilot test work was also conducted on GG1 coal, demonstrating that an eight-turn low density cut-point spiral achieves the targetted 10.3% ash under controlled conditions. Keywords: Spiral, low-cut, coal

Jan 1, 2020

By James C. Barker

The Bureau of Mines evaluated the tin development potential of the uplands between the Kanuti and Hodzana Rivers from 1978 through 1980. Chemical and petrologic data indicate that local granitic intrusions are generally similar to "tin granites" that contain tin deposits elsewhere. The tin mineral cassiterite (SnO2) was identified in chlorite-rich greisen from the Sithyiemenkat pluton. Greisen zones are located near the intersections of high-angle, linear structural features, and samples contain up to 0.23 pct Sn. One bedrock exposure of greisen is 10 to 15 ft wide. Although some lode mineralization is present, the deeply eroded nature of the region suggests larger tin-bearing cupolas may have existed prior to erosion. Extensive stream gravel deposits have not been affected by glaciation, and potential exists for placer tin deposits. Especially favorable is a large semiclosed basin drained by the Kanuti Kilolitna River. Heavy mineral concentrates collected from surface alluvium in the Kanuti Kilolitna River valley contained up to 51.2 pet Sn (0.02 to 0.4 lb/yd3 Sn), up to 5 pct W, up to 0.4 pct Cb(Nb), and up to 0.1 pct Ta. The concentration of heavy minerals is expected to in- crease with depth. Detailed mapping and extensive surface and subsurface sampling will be needed to quantify the mineral development potential of the lode and placer tin deposits in the uplands.

Jan 1, 1986

By Limao Zhang

This paper presents a novel model to assess the risk of adjacent buildings in tunnelling environments based on Extended Cloud Model (ECM). ECM is an organic integration of Extension Theory (ET) and Cloud Model (CM), where ET is appropriately employed to flexibly expand the variable range from [0, 1] to (-8, +8), and CM is used to overcome the randomness and fuzziness during the gradation of evaluation factors. The risk level of a specific adjacent building is assessed by the correlation with the cloud models. A confidence indicator ? is proposed to illustrate the rationality and reliability of evaluating results. Ten buildings adjacent to Wuhan Metro Line Two (WMLT) are randomly chosen among hundreds of adjacent buildings for a case study. Results have proved to be consistent with the actual situation. Compared with other traditional evaluation methods, ECM has been verified to be a more competitive solution with high calculation accuracy, wide adaptability, as well as simplified computer programming. There are no stringent requirements on the quantity of training data during the modelling process, and the original data can be directly entered into ECM without a normalization procedure, avoiding the potential information loss. ECM can be offered as a decision support tool for the risk assessment in urban tunnelling construction and worth popularizing in other similar complicated projects.

Aug 1, 2013

By Yongsik Jeong, Kwangmin Kim

Conventional tailings slurry contains a significant amount of water, and water management is key to ensuring the stability of a tailings storage facility (TSF). Simply reducing the water content in the slurry before discharging it from the mill could be an effective way to improve TSF water management. This study investigated the potential for using an environmentally friendly polymer as a new drag reduction agent (DRA) to reduce frictional pressure loss and also conserve water. It entailed conducting pipe loop tests to assess the polymer’s effect on pressure loss in tailings flow and then applying the test results to validate a numerical model using computational fluid dynamics (CFD). The model was also used to determine the polymer’s optimal concentrations at given solid concentrations and flow rates, its effect on energy efficiency for tailings transportation, and its potential for saving water. A case study for a mid-sized, hard-rock mine with a throughput of 50,000 t/day found that the solid concentration could be increased from 30 to 45% with no pressure loss by applying 1996 m3 of the polymer per day. Adding the polymer also resulted in water savings of 57,552 m3/day. The results of this study demonstrated the potential for using the new DRA not only to improve TSF stability but also to save water.

Jun 29, 2020

By M. B. Hopkins

FOR years the expression "except rubber, tin, and manganese" has appeared in practically every discussion of the natural resources of the United States. Knowledge that natural rubber is not produced in the United States has now spread from the relatively few who have reason to be interested in the country's basic raw material supplies to all those who ride in automobiles, which means everybody. This "everybody" reads in the daily papers that we have a stock pile of natural rubber and that plenty of synthetic rubber is just around the corner. Statistics as to the United States' rubber requirements and sources of supply are of interest to him only to arrive at an answer to the question : "After taking care of rubber requirements for military purposes, will there be rubber for my automobile and the many other rubber articles I want?" More than 30,000 different rubber articles are manufactured in addition to the tires and tubes which use up about 70 per cent of the rubber supply.

Jan 1, 1942

By Robert H. Richards

This is in part a review paper, indicating the various steps that have been taken in developing hindered-settling apparatus, some of the standard data that have been obtained, and some of the conclusions one is led to as to the effect of it in improving concentrating-methods and machinery, and in part it brings in some unpublished work. Causes oF Loss in ORe-ConcEntration. In making a study of the separation of valuable minerals from the waste gangue, particularly by water concentrators, it is necessary to define, first of all, what are the causes of loss that are likely to interfere with the concentration. Having made this definition, we can then study to see in what may the machines make their losses, and plan remedies for them in an intelligent way. Losses may be stated to occur as included grains, as flat or long grains, as fine free mineral, and as absolute slime. We will take these up one by one, as follows: Included Grains.—Fig. 1 shows by a set of diagrams how included grains may occur : first, where the heavy mineral grains attached to the quartz are of large size; secondly, where they are of small size; and thirdly, where very fine particles of heavy mineral are included in the quartz. We have to decide in regard to included grains whether they are rich enough to go direct to the furnace, or poor enough to throw away, or whether they lie between these two points and require recrush-ing as the only means of severing the values from the waste. This last case is the orlly one requiring special treatment at our hands. We will therefore consider that next.

Jan 1, 1911

By Andrey V. Yevdokimov

The results of the test work on gold leaching using high strength of cyanide solution in the presence of activators are presented. The major physical and chemical relationships of gold leaching were determined. Intensive cyanidation results of gravity concentrates with various material compositions using an activator are given. Process design criteria for intensive cyanidation unit were developed on the base of pilot plant test results. Keywords: gold, activators, intensive cyanidation, gravity concentrates

Sep 1, 2012

Summary of the morning's events with a Written Contribution to Paper No. 4 and author responses

Jan 1, 1947

By Albert F. Duzy

Recently there have been some problems associated with hot coal in shipments from the USA to overseas markets. This paper will serve several functions. First, a brief review is presented, together with a selective bibliography. Second, a thorough discussion of coal oxidation is covered. Third, potential effects of storage are presented and, lastly, methods are suggested for the safe storage and bulk transfer of coal. The scope includes coal storage for power plants.

Jan 1, 1983

By D. D. Macdonald, G. Engelhardt

The accumulation of damage due to localized corrosion [pitting, stress corrosion cracking (SCC), corrosion fatigue (CF), crevice corrosion (CC), and erosion-corrosion (EC)] in complex industrial systems, such as power plants, refineries, desalination systems, etc., poses a threat to continued safe and economic operation, primarily because of the sudden, catastrophic nature of the resulting failures. Of particular interest in managing these forms of damage is the development of robust algorithms that can be used to predict the integrated damage as a function of time and as a function of the operating conditions of the system. Because complex systems of the same design rapidly become unique, due to differences in operating histories, and because failures are rare events, there is generally insufficient data on any given system to derive reliable empirical models that capture the impact of all (or even some) of the important independent variables. Accordingly, empirical models have generally failed to provide a robust basis for predicting the accumulation of corrosion damage in complex systems under realistic operating conditions. The alternative prediction philosophy is determinism, in which the development of damage is described in terms of valid, physico-electrochemical mechanisms with the output being constrained by the natural laws. The differential damage is then integrated along the corrosion evolutionary path for the system (i.e., over the future operating "history") to yield the desired integrated damage, which is the quantity that is most useful to an operator. In this paper, we review the theory of predicting corrosion damage within the framework of Damage Function Analysis (DFA), with particular emphasis on the pitting of aluminum in chloride solutions and on the accumulation of damage from SCC in Type 304 SS components in the primary coolant circuits of Boiling Water (Nuclear) Reactors (BWRs). These cases have been selected to illustrate the various phases through which localized corrosion damage occurs.

Jan 1, 2005

By Charlie Wyche

Principal mineral products in the Dominion of Fiji were gold, silver, pit and quarry construction materials, and cement. In the years 1978-79, the combined total value of these commodities accounted for some $15 million,2 or 85% of the total mineral output. Production of cement, sand and gravel, and quarry products increased substantially, but gold and silver output from Fiji's only operating metal mine continued the down-ward trend of recent years. Mineral exploration by several international mining companies as well as by local prospectors was being carried out over much of Fiji, and a number of interesting prospects were discovered. One of these, a medium-size porphyry-copper prospect in the Namosi area of Viti Levu, W88 at a mining feasibility study stage. At Mount Kasi on Vanua Levu, an extensive program of geological sampling and mapping W88 being conducted, and surface sampling and drilling W88 taking place at some base metal prospects in the south-central parts of Viti Levu. Also, high gold values in surface samples were reported at Vuda in western Viti Levu.

Jan 1, 1981

By J. Groyecki, M. Markuszewicz, J. Lassota, A. Zawada

The ratio of stable to unstable inclusions was found to ploy an essential role in the process of sccorldar-y recrystatlizalion in Si-Fe. The analysis of the free energy of inclusions in the range of heat-treatment of individual inclusions to be predicted. The effects MnS. ns inslable inclusions. were investigated. TO secure a high induction, the secondary recryslulliztt-lion associated wilh the texture is necessary. To obtain a low core loss an additional refiuing in the solid state is required. It has been found that sulfur can be more easily removed in racunm than in hydrogen and thai this process was hindered by the prescrzce of INCLUSIONS play an essential role in the development of cube-on-edge texture in Si-Fe. Their function consists in restraining the growth of primary grains up to about 900°C and in passing subsequently into solution at higher temperatures. This process is accompanied by the selective growth of secondary grains with (110)[001] orientation. The general effect of inclusions depends on such factors as the type of impurities, their amount. dispersion and stability, the conditions of diffusion in the space of lattice of metal, and the reactions at the metal/gas interface. In recent years, some of these factors were the subject of a special investigation. A positive influence of Mns, siN,' and vN3 has been established. The quantity of impurities4 and their dispersion5 have been found to be of major importance. Attention was called to the vital importance of diffusion and the conditions under which the impurities are removed from metal., It has also been demonstrated that in Fe-Si alloys by the techniques of powder metallurgy a special opportunity exists to obtain the (110)[001] type texture. 6 The aim of this work was to conduct qualitative investigations on the influence of inclusion stability on the development of cube-on-edge texture in a metal containing approximately 3 pct Si. Experiments were carried out on cast alloys and on those manufactured by powder-metallurgy techniques. The results obtained from these experiments were utilized to explain the phenomena involved and to analyze the relationships between stable and unstable inclusions and the magnetic properties of alloys. EXPERIMENTS AND RESULTS The raw materials used in these experiments were the powder of carbonyl iron with the analysis (in pct) 0.044 C, 0.01 Mn, 0.005 Si, 0.009 P, 0.002 S, traces of Cu, 0.06 Ni, 0.0015 Al, 0.03 Cr, 0.02 Mo, 0.01 Ti, 0.002 Co, traces of Pb, and the powder of silicon containing 94.14 Si, 0.003 S, 0.048 C. The powders were ground and mechanically mixed in 100-g batches. and then pressed at 9 tons per sq cm into 74 by 24 by 8 mm blocks. Sintering was carried out at 1100°C for 12 hr in vacuum (2 x lo-' Tr) or in hydrogen. In this instance the material was heated slowly and subjected to prolonged soaking at 350°, 650°, and 750 2C, respectively, to secure reduction of ferro-oxides. This was checked by making measurements of the dew point, which was found to change from -15" to -35°C after reduction. The compacts after sintering were hot-rolled to 2.4 mm, annealed at 800 C, and finally cold-reduced to 0.35 mm with intermediate annealing at 800°C at a gage of about 0.8 mm. Impurities were added in the powdered form and mixed with iron and silicon powders. Sulfur in the elemental state, electrolytic manganese, and pure aluminum oxide were employed. Besides, to obtain a material with low contents of impurities, especially

Jan 1, 1967

By C. W. Baxter

Eveleth taconite company was formed in 1963 to mine and beneficiate taconite on the Mesabi range of Minnesota. Its thunderbird mine is located midway between the cities of Eveleth and Virginia, Minnesota, and the crude ore is transported by rail to its Fairlane plant approximately ten miles to the south of the mine, "figure 1". As is implied by the names of the mine and plant, the ford motor company is the principal owner of Eveleth taconite company, with an 85% interest, Oglebay Norton company holds the remaining 15% interest and also is the managing agent.

Jan 1, 1972

By Xiang-dong XING, Zhen-yang wang, Jian-Liang Zhang

Distribution behavior of titanium between CaO-SiO2-MgO-Al2O3-TiO2 and hot metal was studied between 1350 °C to 1600 °C. Experimental results indicate that the reaction temperature influenced the activity coefficients of titanium and resulted in the variation of equilibrium constant. Finally, the Gibbs free energy formula of titanium carbothermic reduction was fit out using the thermodynamic model of Wagner and congregated electron phase models.

Jan 1, 2015

By H. Bai, B. G. Thomas

"A three-dimensional finite difference model has been developed to study the liquid steel-argon bubble two-phase turbulent flow in continuous casting tundish nozzles. Experiments have been performed on a 0.4-scale water model to verify the computational model by comparing its prediction with velocity measurements using PIV (Particle Image Velocimetry) technology. The computational model was developed using CFX and then employed to investigate the effects of various casting process variables. A fast, simple inverse model to quantify relationships between those process variables was developed, based on interpolation of the numerical model results, using Bernoulli's Equation and advanced multivariable curve fitting methods. Predictions using this model compare well with plant measurements. The model has been applied to present trends and observations on the relationship between casting speed, tundish depth, slide gate opening, and argon gas injection rate. The results can also be used to predict .the theoretical steel flow rate through the nozzle, so that clogging conditions can be identified in the plant.IntroductionTundish nozzle geometry is one of the few variables that are both very influential on the casting process and relatively inexpensive to change. Designing an effective nozzle requires quantitative knowledge of the relationship between nozzle geometry and other process variables on the influential characteristics of the flow exiting the nozzle. This relationship depends on the flow pattern within the nozzle components. Most previous modeling studies of flow in the nozzle have focused on single-phase flow [1-4]. Argon injection into nozzle is an efficient and widely employed method to reduce nozzle clogging, even though the real working mechanism(s) are still not fully understood [5]. Argon injection may greatly affect the flow pattern in the nozzle, and subsequently in the mold. Therefore, two-phase flow modeling is needed to improve understanding of fluid flow in the nozzle."

Jan 1, 2000

By J. E. Chilton

The Bureau of Mines has examined the operation of an oxygen sensor manufactured by the City University, London, England. The sensor produces a current proportional to the oxygen concentration by reacting oxygen at a nonconsumable cathode. The sensor design is unique in that the primary mode of oxygen transport to the cathode is by diffusion through a capillary, The sensor using this design has a stability of 0- to 0.02-pct reading change per day over a 4.7-month test, small temperature coefficient of 0.29-pct reading change per °C, and small pressure coefficient of 0.34-pct reading change per 1,000-ft altitude change, If this sensor were incorporated into an oxygen detector or monitor, this would be a distinct improvement in electrochemical-type oxygen analyzers and would be useful to the mining industry.

Jan 1, 1983