Search Documents

By M. H. HARRINOTON

THE Transactions of the Institute afford abundant evidence of the general recognition by mining engineers of the importance of a safety-lamp which will not only give warning of the presence of fire-damp, but will also indicate the proportion in which it is present.' Mining-men are only too familiar with the frequent and sudden changes that constantly occur at the working-face of a gaseous mine. Nothing illustrates more forcibly the pregnant condition of the strata enfolding the seam and the seam itself, than the fact that a circulation of perhaps 150,000 cu. ft. of air may contain 2 or even 3 per cent. of marsh-gas, representing a volume of from 3,000 to 4,000 cu. ft. of this gas pouring-out each minute from the natural strata into the mine-workings. It would, indeed, be strange if this great outflow of gas were always constant, and it creates no surprise that such earth-breathings, as they may be called, are spasmodic and irregular in their wane and flow. There are other causes that act to vary the gaseous condition of mine-air. Gas has a tendency, often very manifest in mine-workings and airways, to stratify and, at times, to travel long distances in veins or streams. It is common to catch and lose the gas in the lamp when making a test. At times two lamps, held side by side in an air current, will indicate different gaseous conditions of the passing air. When testing for gas, the lamp may suddenly fill with flame, in a mine-chamber, where a moment before a careful test showed the presence of but 1 per cent. of gas. It is sometimes remarked that there is little need of detecting a smaller percentage of gas than is revealed by the common

Jan 1, 1906

By Edward L. Burwell

The Bureau of Mines conducted laboratory experiments to determine the change during retorting in the apparent permeability and the degree of compaction of beds of broken oil shale. Grades of oil shale studied ranged from 20.6 to 46.7 gallons of oil per ton (gpt), and the simulated overburden pressures applied to the shale were from 300 to 900 psi. Linear regression analysis of the data produced equations describing the response of the oil shale. Oil shales of approximately 20 gpt experience only minor apparent permeability reductions under test conditions, but richer shales (30 to 50 gpt) lose essentially all permeability. The permeability reductions were accompanied by corresponding decreases in bed height that ranged up to 37 percent of the original bed height.

Jan 1, 1974

By Joseph B. Story, John T. Clarke

A modification, of the Kelvin bridge using an inductor was used to measure the conductivities of molten sodium chloride, calcium chloride, and mixtures thereof. A capillary-type four-lead fused quartz dipping cell was constructed. The effect of a small amount of potassium chloride on the conductivity of the melt was determined. IN the electrowinning of sodium and chlorine from sodium chloride in Downs cells, calcium chloride is added to the sodium chloride in an approximately equimolar amount to permit cell operation at a lower temperature. This lower temperature improves current efficiency and ease of operation, but decreases voltage efficiency by decreasing the electrical conductivity of the melt. A knowledge of the electrical conductivity of the Downs cell melt is necessary to the understanding of Downs cell operation, for the IR voltage drop across the melt is responsible for a significant part of the electrical power consumed by the cell. The work of previous investigators on fused sodium chloride-calcium chloride mixtures was reviewed from the standpoint of consistency with the results of others on the conductivities of the pure constituents. The electrical conductivity of pure fused sodium chloride has been established with accuracy by Van Artsdalen and Yaffe,1 by Edwards, Taylor, Russell, and Maranville,2 and by Lee and Pearson.3 It has also been studied by a number of other investigators.4-13 The best values for calcium chloride are believed to be those of Lee and Pearson,3 since the sodium chloride and potassium chloride conductivity values given by them check the best literature values. A number of other investigators have also reported values for calcium chloride.'-"."' Electrical conductivity data for fused sodium chloride-calcium chloride mixtures have been reported by Sandonnini,12 Vereshchetina and Luz-hnaya,18 Ryschkewitsch,11 Barzakovskii,5 and Alaby-shev and Kulakovskaya.15 Sandonnini reports no data at temperatures lower than 850°C. The conductivity values reported by Vereshchetina and Luz-hnaya, by Ryschkewitsch, and by Barzakovskii for pure sodium chloride and for pure calcium chlor- ide vary somewhat from the literature values believed to be best and the sodium chloride-calcium mixture data of these authors and of Alabyshev and Kulakovskaya (who give no data for the pure compounds) show significant variations. In view of these facts, it seemed that an investigation of the electrical conductivities of fused sodium chloride-calcium mixtures would be worthwhile. Apparatus Bridge System—The bridge used,in this investigation is diagrammed in Fig. 1. In general, the elaborations of this bridge over the simple Wheatstone bridge were for the purposes of a) eliminating lead resistances or making them accurately measurable, and b) eliminating major capacitative and inductive effects or balancing them against each other. Lead resistances in the lower arms of the bridge were kept as low as possible by making the leads short and of low resistance wire. This could not be done in the cell arm of the bridge because of the remoteness of the cell from the other bridge components and because of the high-resistance nickel or chrome1 wires used in the cell. Since maximum sensitivity is attained when the resistances of the four arms of the bridge are equal, 50-O resistors were used in the lower arms of the bridge when fused salt conductivities were being measured, and 1000-O resistors were used when the cell was being calibrated with normal aqueous KCl solution. The cell resistance was of the order of 50 ohms with fused salts and of the order of 1000 ohms with normal aqueous KC1 solution. The resistors used were non-inductive and accurate to 50.05 pct (General Radio Co. Types 500-C and 500-H). The lead resistance between point A in the cell and point E at the measuring resistor was eliminated by using the kelvin bridge principle; that is, the voltape drop across the lead from point A to point E was divided between the cell arm of the bridge and the measuring arm of the bridge in proporation to the resistaxes in the lower arms of the bridge.

Jan 1, 1958

By A. R. Kaufman, P. Gordon

THE large-scale manufacture and use of uranium in conjunction with the atomic energy development during the war led to a need for knowing the equilibrium diagrams of uranium with various other metals. The alloys of uranium with aluminum and with iron were among the first that were studied for this purpose. Much of the work was done in the manner of a survey since it was necessary to determine the important features of the phase diagrams rather than to obtain completely detailed results. For this reason no attempt was made to locate exactly such features as liquidus lines, solid solubility limits and compound and eutectic compositions. It is believed, however, that there are no great inaccuracies in the diagrams reported here and that no important points were overlooked. Earlier work on alloys of uranium with aluminum and iron is almost nonexistent and in each case is considered to have been of little value by M. Hansen. It is interesting to note, however, that the compound UAl3 was first reported in 1902 by L. Guillet. Experimental Procedure Materials: The uranium used for making most of the aluminum alloys was obtained from material prepared by Metal Hydrides, Inc., and melted in vacuum at M.I.T. Because of the lack of an adequate supply of metal, it was necessary to use material from several different batches and hence it is impossible to state an exact analysis. However, a few results indicated about 0.01 to 0.03 pct iron and probably about 0.03 to 0.05 pct carbon. Toward the end of the work a small amount of metal was obtained from Brown University and from Iowa State College and this was used in determining the transformations in pure metal and in some dilute alloys. All of the aluminum used in this investigation came from a supply of high purity metal (greater than 99.9 pct aluminum) which was obtained through the courtesy of Dr. Mehl of the Carnegie Institute of Technology. The uranium used for making the alloys with iron was produced by the bomb reduction process which has been described by J. Chipman.² This metal, after vacuum melting, contained about 99.9 pct uranium by weight with carbon and iron as the chief impurities. Electrolytic iron containing about 0.012 pct carbon, 0.020 pct nickel and 0.009 pct copper was used in making the melts. Melting Equipment: The melting of the alloys went through a stage of development which culminated in the use of beryllia or beryllia-lined crucibles and in the use of high frequency heating in either vacuum or in an atmosphere of argon. It was found that uranium at a few hundred degrees above its melting point would pick up aluminum and to a lesser extent silicon from an alundum thimble while aluminum above 1000°C would extract silicon from the impure alundum. No reaction of either metal with beryllia was noted at temperatures as high as 1800°C. The distillation of aluminum from the aluminum-rich alloys was quite troublesome at temperatures above about 1300°C and was only partially avoided by the use of argon instead of vacuum. Melting in resistance furnaces,

Jan 1, 1951

By Wood CJ, Davis JJ, Askew H

A dynamic model of a dense medium circuit has been developed and tested against plant data. The model shows the response of the circuit to both controlled (changes in specific gravity set point or changes in circuit coal feed rate) and uncontrolled changes (changes in raw coal moisture, loss of raw coal feed) in operating conditions. The model is built up from dynamic models of the individual sumps, pumps, pipes, splitters, magnetic separators and automatic controllers in the circuit. The model can be used for design of automatic control loops and for investigation of possible process modifications such as changes in water addition points. This paper describes the model construction, the testing of the model against actual plant data and gives some examples of its use in investigating plant response to changes in operating conditions.

Jan 1, 1978

By John W. Weeton, Donald W. Petrasek

Relatively few metal-metal systems exist that would permit the creation of fiber-metal composites consisting of mutually insoluble constituents. It is anticipated that most high strength-to-weight ratio and high -temperature fiber composites ultimately to be produced will utilize high-strength fibers embedded in a highly alloyed matrix. An investigation was conducted to determine the effect of alloying on the tensile Properties and micro-structure of tungsten-fibey-reinforced composites. Composites were made of tungsten fibers infiltrated with copper binary alloys that contain elements of varying solubility in tungsten. Room-temperature tensile tests were made on the composites, and a metallographic study of the microstructure of the fiber-metal-matrix interfaces was conducted. It was shown that, as the depth of penetration of some alloying elements into the fiber increased, a decrease in both tensile strength and ductility of the composite results. A notch effect, due to the formation of a brittle alloy zone with the tungsten fiber, was observed and gave rise to greater reductions in tensile properties and ductility behavior than would be Predicted by a law-of-mixture relation alone. In recent years, investigators have considered combining fibrous materials with relatively weak binder materials. The interest in fiber-reinforced composites results from the fact that fibers or wires may be exceedingly strong and exhibit mechanical properties superior to those of the bulk materials from which they are derived. For example, tungsten wires drawn to less than 1 mil in diameter may have strengths of over 600,000 psi,' while steel wires ranging from 10 to 3 mils in diameter may have strengths of the order of 300,000 to over 600,000 psi.2 Both metallic and ceramic whiskers are known to have very high strengths. For example, iron whiskers have been shown to have strengths of 1.9 million psi3 and sapphire whiskers have been reported to have strengths of the order of 1.7 million psi.4 If all or part of the strengths of such fibers could be retained, subsequent to the incorporation of the fibers in an engineering material, a superior material could result. In previous work done at the Lewis Research Center, McDanels, Jech, and weeton5 demonstrated the feasibility of fabricating metal-fiber—metal-matrix composites that utilized the full strengths of the fiber and matrix materials. Tungsten fibers were combined with a copper matrix by a liquid-infiltration method such that the tungsten fibers were uniaxially oriented parallel to the tensile axis of the composite. A linear relation was established that related the tensile strength of the composite with the volume percent of the fibers. Mutually insoluble constituents were selected for the study so that the strength of the composite could be quantitatively related to the strength of the individual constituents. The fact that there are only a few metals that are mutually insoluble with tungsten, e.g., copper, silver, gold, and zinc, and that these either have low melting points, high vapor pressures, or poor oxidation resistance, makes it necessary to utilize other metals that are soluble in tungsten, where high-temperature applications are ultimately contemplated. It was anticipated that, for most practical fiber-reinforced composite materials, it would be necessary to use a fiber and metallic matrix that would have varying degrees of solubility for each other. A logical extension of the earlier work was thus felt to be a study that would determine the effects of elements that had mutual solubility with the tungsten. Numerous investigators have found that tungsten fibers may be damaged by thermal treatments or contamination of the surface of the fiber by alloying elements.6-10 On the other hand, surface treatments may improve the strength of such fibers."-" Relatively little work with composites containing tungsten fibers have been reported. The work of parikh14 has shown that kinked, short-length tungsten, steel, and molybdenum fibers could str'engthen such matrices as silver, gold, and copper. Some of the combinations of fibers and matrices studied by

Jan 1, 1964

By D. L. McCain

In considering slurry transportation for Consolidation Coal Company's Loveridge Mine in Northern West Virginia, many things were taken into account. The advantages of slurry transportation in comparison to shuttle car, belt and rail transport have been given in previous publications." These include increased safety and the potential for increased productivity. In addition to these considerations, the slurry transport system installed in an existing mine provides an alternate or additional transportation mode to the one already existing. In the Loveridge Mine, this is rail haulage. Since the rail system is a single track system and the distances involved are several kilometers, it is not always possible to provide for haulage of loaded cars, return of empties, supplies and maintenance in an efficient manner. Slurry transport of the coal from the production faces to the preparation plant allows the rail system to fulfill the remaining transportation needs in an efficient manner. Consol initiated development work in slurry transportation in the early fifties leading to the construction and operation of the 174-km (108-mile) Cadiz-to-Cleveland pipeline which carried 1,200,000 metric t/y (1,300,000 t/y) from 1957 to 1963. Development work on coarse coal slurry transportation for underground mines started in 1970 with feasibility tests on coarse coal at Conoco's Ponca City, Oklahoma, slurry test facility. A series of tests were conducted in several locations as development work proceeded on the various subsystems, mechanical equipment and controls required to produce a working system to follow a continuous miner in a room-and-pillar type mine, then to combine the coal production from several mine faces for mainline transportation to the preparation plant. The face system, including the crusher-pump vehicle, hose hauler vehicle, slurry booster pump units, return water unit and 900 to 1,200 m (3,000 to 4,000 feet) of pipeline was brought together for the first time and tested as a system at Consol's Robinson Run Mine in northern West Virginia in 1975. A pipeline wear test at the Loveridge Mine where 300,000 tonnes (330,000 tons) of minus 127-mm (5-inch) run-of-mine coal were pumped from the raw coal bin into the preparation plant and a large scale test in Ponca City on a multiple feed sump where several slurry flows could be combined to provide surge capacity and a constant reclaim rate for mainline transportation completed the preliminary testing for a complete system. A decision was made to commit the system to a mine, and the south half of the Loveridge Mine was chosen. This site required the transporting of coal from one longwall and two continuous miner development faces. To prevent startup and unexpected problems in the slurry system from shutting down production of coal from the longwall face, the rail car loading point from the main section belt was chosen as the feed point for the slurry system and the design would allow for rapidly switching from one transport mode to the other. Scheduling of required development entry work and the developmental nature of the system led to a decision to install only one continuous miner face slurry transport system rather than two for this first system. The type of continuous miner in use at the mine for the foreseeable future was the Joy 2BT6 twin boring machine. This machine cuts a stable, arch-shaped entry and was therefore allowed to mine about 26 m (85 feet) of entry before roof bolting was re¬quired. Since peak production from this type of machine was not high, a smaller transport system could be used with it.

Jan 1, 1981

By J. J. Ferreira, M. L. Thurston, I. L. Chinn, D. M. Rose

"Concerns about using microdiamonds for resource estimation have been raised by workers because multiple diamond populations exist in many parts of the mantle source region, small diamonds in kimberlite could be exposed to proportionately greater levels of resorption and modification, and euhedral microdiamonds could crystallize immediately prior to kimberlite eruption. This paper addresses these concerns; discusses the geology of the mantle, the principal diamond host rocks, and the impact of mantle processes; compares micro- and macrodiamond properties and features; and outlines steps to identify and mitigate the risk of diamond resorption and its impact on the diamond grade-size relationship.RÉSUMÉ Des travailleurs se sont interrogés sur l’utilisation de microdiamants pour estimer la ressource; en effet, de multiples populations de diamants existent dans plusieurs secteurs de la région source dans le manteau. Des petits diamants dans la kimberlite pourraient être exposés à des niveaux proportionnellement supérieurs de résorption et de modification; de plus, des diamants idiomorphes pourraient cristalliser immédiatement avant l’éruption de la kimberlite. Le présent article traite de ces questions, discute de la géologie du manteau, des principales roches-mères des diamants et de l’impact des processus dans le manteau, compare les propriétés et les caractéristiques des micro- et des macrodiamants et définit les étapes pour identifier et mitiger le risque de résorption des diamants et son impact sur la relation entre la taille et la qualité des diamants."

Jan 1, 2016

By Barry J. Turley

With over 700 large electric-drive haulage trucks operating in Canadian mining today and over 3700 in mines worldwide, most aspects of electric drive are well known. Recently, however, extensive application of these trucks to down-hill hauling in mountain mining makes it vitally important that many of us better understand the operation and proper application of the dynamic retarding feature of these vehicles. This paper is an attempt to clear up misunderstandings on this subject, to suggest precautions that mining operators should take in comparing competitive retarding systems and to challenge equipment manufacturers to evolve improvements to the important aspect of system performance.

Jan 1, 1978

By Brandon M. Robinson, Osman F. Besler, Dominik Gaechter

The Sandbukta-Moss-Såstad (SMS) project is a part of the Intercity development project, which is part of the largest transport project in Norway, consisting of 270 km of new double-track rail. The SMS project consists of 10km of double-track railway including three open stretches and two tunnels. Soil conditions consist of quick clay underlain by Bedrock. Dry soil mixing (DSM) was considered as the main soil improvement method to allow for excavation of the quick clay and construction of the D-Wall panels. The preliminary design revealed around 25,000 ton of binder installation. Therefore, a test field has been conducted to evaluate binder alternatives in means of improved soil strength by considering CO2 emissions. Multicem and Standard cement (Standard FA) have been compared for that purpose. Multicem is a type of binder which mainly consists of Portland cement and cement kiln dust (CKD). CKD is a fined-grained, solid, highly alkaline material removed from the cement kiln exhaust gases. reverse column penetration test (FOPS) and pre-drilled column penetration test (FKPS), which are common tests to evaluate DSM strength have revealed comparable strength outcome for both binder types. Therefore, Multicem has been selected as the main binder type to be used further which provided a reduction in CO2 footprint of up to 40%.

May 1, 2022

By A. S. Choudhary

Most of the coal reserves in India are of drift origin and have very poor washability characteristics and a high level of near gravity materials. At least 30 new coal wash plants are expected to be set up in the next 5years.In such a scenario, adequate sampling followed by sink float test work for washability analysis becomes very critical for designing these new plants. For coal sampling purpose, stipulations of different standards are sometimes formidable and on the border of ?impracticality?; sometimes are self contradictory in terms of gross sample weight vis-a-vis minimum number of particles required in each size fraction and in each relative density fraction and also the minimum mass in the latter. Validation of the generated data is another important aspect of washability analysis. These issues can easily be addressed by using straight forward mathematical relationships, well known RR plots and by using simple MS Excel tool, etc.

Sep 1, 2012

By E. V. Bratygin, E. G. Dmitrieva

The aim of the research was to study the thermodynamic characteristics of high-temperature processing of ilmenite concentrate deposits "Central" in a neutral and oxidizing atmosphere, as well as its interaction with alkaline additives. The research was conducted using a scanning colonoscopy on thermogravimetrical analyzer NETZSCH STA 449 F3. A sample of the test material weighing 10 mg was placed in a crucible and heated at a rate of 10 °C/min to 1200 °C in argon or air. Studies have been conducted pure ilmenite concentrate and its mixtures with 5 % and 12.5% of sodium carbonate. The results of the analysis of the thermogravimetric curves it was found that the recovery of the concentrate carbon will come from ulvospinel, not pseudobrookite, and the reaction recovery is possible at temperatures above 900°C. While removing produced in the decay ilmenorutile of iron oxides in an inactive form, for example, iron (III) oxide, it is possible to reduce the quantity of the solution of ilmenite formed during the restoration of the melt anosovite. The analysis of data obtained during heating of ilmenite concentrate with sodium carbonate in concentrations of 5 and 12.5% transition pseudobrookite in ulvospinel is missing, it just breaks down into hematite and titanium oxide, which, in turn, react with N?2??3. It should be noted that increasing the concentration of sodium carbonate in the sample contributes to more complete interaction of iron oxides and N?2??3 with formation of ferrites of sodium. This can ensure full recovery of iron oxides in the concentrate, which is part of secondary ilmenite can not be dissolved in the melt formed by the lower oxides of titanium. In addition, the increase in the content of soda in the mixture significantly reduces the temperature of the initial melting point of the slag and facilitates the coagulation of metallic iron.The obtained results were used for laboratory studies of the solid-phase sintering of briquettes from ilmenite concentrate with additives of sodium carbonate and a reducing – coal, as well as for the development of technological mode of solid-phase sintering of the concentrate with the aim of obtaining product recovery with a titanium dioxide content of more than 75 %.

Jan 1, 2018

By R. V. Ramani, V. T. Burgos, J. A. McClay

Model testing is a two part operation; first, to assure the valid¬ity of the mathematical statements and second, to evaluate the accuracy of the computer model for predictive purposes. Verification of both the conceptual and computational aspects can be achieved through the use of input data for which output results are available for comparison. In this dissertation, two test problems were selected for model testing from the Economic Evaluation Reports of the U.S. Bureau of Mines, Process Evaluation Group. Verification Data Set I Input data for this test was selected from an economic analysis of a hypothetical 1,056,000-ton-per-year mine in a 48-inch bituminous coal seam (Process Evaluation Group-Report No. 72-27, 1972). The mine was scheduled to operate five days per week, three shifts per day, 220 days per year with an estimated life of 20 years. Coal reserves covered an area of 6.4 square miles with an expected recovery rate of 70%. Production was achieved through 4 continuous miner sections with an average production rate of 400 tons per shift. The cost summary in the report included a breakdown of equipment and labor requirements. A depreciation schedule listed the expected capital expense per year of operation, assuming capital replacement with identical units and no change in the unit cost. Supply and oper¬ating costs were listed in both gross annual figures and cost per ton of production. The operating and investment costs were projected over the 20 year mine life and a discounted cash flow analysis performed to determine

Jan 1, 1975

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By Derek Brennan, Donald Brennan

"The existing Rondout West Branch Tunnel (RWBT) is part of the Delaware Aqueduct which has been in service since 1944 and accounts for more than 50 percent of New York City’s water supply. In early 2015, the New York City Department of Environmental Protection contracted Kiewit-Shea Constructors, AJV (KSC) to construct the Rondout West Branch Bypass Tunnel project (Rondout) in order to mitigate the leakage of 132 million L/ day (35 million gpd) of water from two areas of the existing tunnel; the Roseton and Wawarsing areas.The scope of the Bypass Tunnel 2 project is separated into two distinct phases. Phase 1 consists of completing the shaft sinking to a depth of approximately 274 m (900 ft) at shaft 5B, 213 m (700 ft) at shaft 6B and the excavation of approximately 3,850 m (12,500 linear ft) of tunnel at a diameter of 6.6 m (21 ft 7 in). This phase also includes the installation of 2,804 m (9,200 linear ft) of 4.8 m (16 ft) diameter steel interliner pipe through the new bypass tunnel with cast-in–place concrete liner for a finished diameter of 4.2 m (14 ft). Access chambers at the top of shafts 5B and 6B will be constructed for access and housing of the mechanical and electrical equipment for supporting pumps and valves.Included in phase 2 is the additional excavation from shafts 5B and 6B to the RWBT, and the drainage tunnel to remove ground water infiltration from RWBT. This work will be completed during a scheduled shutdown of the RWBT and will include approximately 31 m (100 ft) of excavation of the two connection tunnels. Additionally, construction of the permanent plugs within the RWBT will be undertaken. Figure 2 shows the layout of the work.Access to the work through the deep shaft at site 5B was critical to the success of the project. The hoisting system needed to be multi-functional to handle the different types of construction from drill and shoot of the shaft, starter and tail tunnel, the assembly of the tunnel boring machine (TBM), the excavation of the TBM tunnel including the supply of the precast segmental liner, the grouting operations, the installation of the steel interliner pipe and the cast-in-place concrete as well as ingress and egress of personnel. The production of the TBM operations was critical to the schedule of the project. This required a quick cycle for muck haulage and supply of the precast segmental liner in order to keep pace with the excavation time of the TBM. For TBM assembly, components were limited to a maximum weight of 104 t (115 st) for a single lift. Various cranes were analyzed for hoisting, however, none would meet all of the citeria. Therefore, the project team selected a specialized hoisting system designed in house in conjunction with Timberland Equipment Ltd. that consisted of a total of 14 separate hoists and winches with a total of more than 2,833 kW (3,800 hp)."

Mar 1, 2019

Since 2008 rapid advances have been made in technologies for the sensing and sorting of ores, particularly copper, and copper-related ores. Advances include significant increases in the sensitivity and throughput, specifically in the area of bulk sorting. Such advances were not possible without contemporaneous advances in the understanding of copper orebodies, in particular the understanding and quantification of the heterogeneity required within an orebody to support an effective sort, regardless of the technology deployed to do this. This paper covers fundamental knowledge in the characterization of orebodies and their ores for sorting; relationships between measures of heterogeneity and sorting response; the design of bulk sorting systems that can exploit this heterogeneity to add value to copper operations; and, a quantification of the value that can be generated from bulk sorting at a case study mine. INTRODUCTION Society currently puts increasing pressure on industries to move towards cleaner and more efficient means of production, and the mining industry is no exception. Mining additionally faces other factors increasing the pressure to be more efficient: high-grade and easily accessible reserves have become largely depleted, therefore the mined grade at operations across most commodities, including and in particular copper, is decreasing. Additionally, the grade of new discoveries in the sector continues to decrease (Schodde, 2011). Factor in the high capital cost of processing facilities and the low levels of efficiency of current grinding circuits, and the situation for such mines becomes dire. Sorting, by maximizing the amount of ore extracted while simultaneously reducing the waste content in ore delivered to downstream processes (whether simply transport and crushing, or more sophisticated circuits such as grinding and flotation or leaching) has long been of interest to mining operations and projects struggling with low margins (Bamber, 2012). However, until recently sorting technologies that are both cost effective and effective at such high throughputs have not been commercially available.

Jan 1, 2019

By Bowen Li

Copper vermiculite is a special nanomaterial with excellent antibacterial and antifungal performance. By means of ion exchange, copper vermiculite containing up to 5.8wt% copper was prepared. The chemical and mineralogical characterization of the material was investigated in this study based on the XRD, AAS, TEM and EDS analysis, as well as the calculation of crystalline parameters and crystal chemical formula. Cu2+ and Mg2+ have similar atom radius and same electrovalence. Correspondingly, the structure character of copper vermiculite is very close to that of standard Mg-vermiculite. Most of the CU21 may have occupied the interlayer cationic positions in the form of hydrate in vermiculite. However, some may have entered into octahedral coordinate positions. The values of au and bo of the copper vermiculite crystal cell have no obvious change compared to that of original vermiculite micropowder, but the Co value decreased slightly, which is desirable for the stabilization of the Cu2+ in copper vermiculite.

Jan 1, 2003

By John Gittins

Lots 11 and 12, Range IX, Calumet island, are underlain by a Grenville metamorphic complex into which sills of tourmaline granite pegmatite have been injected. The pegmatite has an average mode-potash feldspar 65 per cent, sodic plagicdase 10 to 20 per cent, quartz 5 to 20 per cent, tourmaline 10 to 15 per cent, accessory minerals < 5 per cent; it is unzoned except for a narrow border zone. Some of the feldspar has been replaced by calcite. Microcline has been ?partially replaced by sodic plagioclase. Three varieties of tourmaline are present (black, blue, and green) and spectrographic analysis suggests progressive compositional changes during its crystallization. The presence of U- and Th-bearing minerals in the pegmatite prompted the Quebec Nickel Cor,porat10n, Ltd., to explore the possibility of developing the pegmatite but it does not appear that this is economically possible at the ? present time. Tt\e Grenville metamorphic complex consists of recrystallized limestones and calcsilicate rocks of the albite-epidoteamphibolite facies and the amphibolite facies, which were derived from sedimentary rocks. Several of these are dis-equilibrium assemblages, and retrograde metamorphism has probably formed biotite and epidote from hornblende. The schistosity of the gneisses dips steeply eastward. Numerous strike faults are roughly parallel to the schistosity and one of the pegmatite sills is bounded by such a fault, dipping at 60 ° with about one foot of fault breccia. The general structure of the map-area seems to be an asymmetrical syncline ?overturned to the west. The emplacement of the pegmatite is associated with a period of folding, metamorphism, and igneous intrusion.

Jan 1, 1956

The Great lady gold deposit presented the challenge of providing a new grade control system for an usual type of orebody in the Eastern Goldfields. Mineralisation occurs as secondary enrichment about a quartz sand - granite saprolite contact 30m below surface. The ore horizon, which averaged 2.5m thickness, was near-horizontally disposed in contrast to the typical steeply dipping, shear hosted deposits of the region. A trial mining operation was undertaken on the richest, most continuous portion of the deposit to test the economic viability of this type of orebody. Controlling and minimising vertical ore dilution was considered crucial to the profitability of the operation.An understanding of the grade distribution combined with the practicalities of mining produced a grade control system which allowed for the mining of 1/2rn composited grades on level lm benches. Ore mining was combined with strict monitoring of levels, truck destinations and ore boundaries. Ore reconciliation results showed this system to be effective.

Jan 1, 1990

By Aiyuan Ma, Tu Hu, Chenyu Sun, Yonggang Zuo, Hongying Xia, Jinhui Peng, Libo Zhang, Yongguang Luo

"In this study, the adsorption characteristics of tannin acid in aqueous solution were investigated using regenerated activated carbon (AC), with the aim to remove the tannin acid organic matter from the solution after zinc hydrometallurgy and Ge precipitation. Results showed the temperature has little effect on the adsorption ability (q.) of the regenerated activated carbon. The experimental equilibrium data were tested for the Langmuir and Freundlich isotherms. The adsorption equilibrium was better described by the Langmuir isotherm (R2 > 0.99). Pseudo first- and second-order kinetic models were used for describing kinetic data. It was determined that the kinetics of tannin acid removal was well fitted by second-order reaction.IntroductionGermanium recovery is a complex processes [1]. Hydrometallurgical processes are favoured and these are based on the precipitation of germanium as hydroxide or sulphide or alternately with tannic acid [2]. However, in the germanium recovery process, too much tannin is consumed by the germanium-tannins complexation process, and results in a high content of tannic acid remaining in solution, which is harmful to the valuable metal recovery [3]."

Jan 1, 2014