Search Documents

By J. J. Sammarco

Light emitting diodes (LEDs) are emerging as viable replacements for incandescent-based cap lamps used in mining. The photometric and energy characteristics of these light sources differ in important ways. The present paper describes the performance of LED and incandescent sources in cap lamps in terms of correlated color temperature, color rendering, light output, electric power, ambient temperature and airflow, and light source aging. Importantly, these characteristics can influence a miner?s ability to spot mining hazards thus impacting safety. Secondly, some of these characteristics interact with the operating life of the cap lamp?s battery power, such that differences between LED and incandescent sources can be magnified toward the end of a 10­hour battery discharge cycle. Empirically, we have determined that after 8 hours at an ambient temperature of 25 °C, the average light output of an incandescent cap lamp can decrease to about 69% of its initial value when powered by a lead-acid battery and it can decrease to about 65% of its initial value when powered by a nickel-hydride battery. An LED-based cap lamp using a constant current drive circuit can maintain about 96% of its initial value when powered by a nickel-hydride battery. Real-world tests addressing the effects of ambient temperature and airflow on the light output of an LED and incandescent cap lamp were conducted in the NIOSH Safety Research Coal Mine (SRCM). The LED cap lamp yielded a vertical average illuminance improvement of approximately 9.5% and the INC cap lamp yielded a vertical average illuminance degradation o f approximately 4%. The differences between LED and incandescent cap lamps were further quantified by the calculation of ?mesopic luminance? data that indicated for the same photopic luminance (i.e., as measured using a conventional light meter) the LED cap lamp could be up to 38 % more efficient than the incandescent cap lamp with a lead-acid battery at the end of the 10-hour driving cycle. Lastly, accelerated life tests were used to empirically determine light output depreciation as the incandescent light source age approached its useful life. There was about a 35% decrease in light output. This is quite considerable, especially given that the light output will decrease an additional 30% to 45% over the period of a 10-hour shift. The implications of the differences between LED and incandescent sources are discussed. This information is crucial in determining how visual performance could be affected for real-world conditions where batteries discharge during the work shift and as the light source ages. To date, only idealized conditions have been used for LED and incandescent cap lamp visual performance research.

Jan 1, 2008

By Krishna Parameswaran

"This paper discusses energy use and conservation in the primary copper industry and illustrates eco-efficiency considerations, using select examples of practices at ASARCO LLC, an integrated primary copper producer and others in the industry that promote eco-efficiency. The World Council for Sustainable Business Development first publicized the concept of eco-efficiency at the Rio Earth Summit in 1992. Eco-efficiency is a management concept linking environmental and economic performance and is aimed at generating added value for a business through, among other things, increased resource and energy conservation and reduced environmental impacts throughout the life cycle of the product or service. This concept differs from sustainable development in that focus is only on economic and environmental factors and does not include social considerations. In the metal mining and processing context, this added value can be realized by implementing practices that promote conservation of water and mineral resources, conservation of energy, minimization of waste, reduced emissions and effluents and increased recycling. The examples from the primary copper industry used to illustrate eco-efficiency considerations include: water and energy conservation in mineral processing, adoption of flash and bath smelting processes, emission reduction and process improvement associated with fire-refining, implementation of green chemistry in electrorefining, promoting product stewardship initiatives and fostering renewable energy project on disturbed mined lands.INTRODUCTION ASARCO LLC (Asarco) was organized in 1899 as the American Smelting And Refining Company. Originally a consolidation of several lead-silver smelting companies, it evolved over the years into an integrated producer of primary non-ferrous metals, including copper, lead and zinc and associated co-products. Grupo México, S.A.B. de C.V acquired Asarco in 1999. Today, Asarco is a vertically integrated producer of primary refined copper and associated co-products such as gold, silver, molybdenum, selenium and tellurium. Asarco operates three open-pit mines and mills, two leach, solvent extraction-electrowinning (SX-EW) plants and a copper smelter in Arizona and a copper refinery in Texas."

Jan 1, 2017

By Peter M. Herzig

In 1994 and 1998 the German research vessel R/V Sonne undertook detailed mapping and sampling of the largely uncharted offshore areas of the Tabar-Lihir-Tanga-Feni island chain in the New Ireland Basin of Papua New Guinea. The New Ireland Basin occupies a fore-arc position with respect to the formerly active Manus-Kilinailau arc-trench system and hosts a series of Pliocene to Recent alkaline volcanoes which are built on rifted Miocene sedimentary basement. Several of the volcanoes possess high-level porphyry stocks and active geothermal systems, including gold-depositing hot springs and the giant (40 million ounces) Ladolam gold deposit on the island of Lihir. On the southern flank of Lihir island, a group of three volcanic cones were discovered at water depths from 1.000-1.500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered volcanic rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts (ankaramites), porphyritic phlogopite basalts, and trachybasalts. Unusual gold-rich hydrothermal precipitates were recovered from the summit of the 600 m high Conical Seamount located only about 10 km south of Lihir Island. 1200 kg of sampled material systematically collected with a TV-guided grab from the top plateau (150 x 200 m, 1.050 m water depth) are intensely mineralized with pyrite, marcasite, minor sphalerite, chalcopyrite, galena, tennantite/tetrahedrite, and orpiment/realgar together with traces of anglesite, cerrusite, and amorphous silica in stockwork-like veins. Bulk samples of the vein mineralization consist mainly of clays, silica, and disseminated sulfides, and have an unusual high gold content ranging from 1.2-44.0 ppm Au. In some of these samples, grains of native gold (about 1 micron in diameter) were identified by SEM in pyrite and sphalerite. The gold-rich material also contains high concentrations of silver (up to 1000 ppm) and typical epithermal elements such as As (2.6 wt.%), Sb (0.2 wt.%), and Hg (34 ppm). Similar to epithermal deposits on land, which usually have only low base metal contents, the samples from Conical Seamount contain only minor amounts of Zn (max. 4.5 wt.%), Cu (2.0 wt.%), and Pb (2.0 wt.%). Many of the samples recovered from Conical Seamount are virtually identical to the gold ore at Lihir.

Jan 1, 1998

By Andrew R. Thomas

As the demand for most industrial minerals on the world market continues to climb, educational institutions maintain traditional policy in emphasizing chiefly metallic ore deposits and energy resources in addition to the general disciplines. In spite of their increasing importance, few universities exhibit great depth with respect to industrial minerals courses due to the shortage of specialized faculty in a category this broad. As new ideas are formulated and technological advances are developed in the field of industrial minerals, the classroom still exists as a student's primary source of information. This opportunity to give today's students the benefit of modern developements has not been utilized to its utmost potential.

Jan 1, 1981

By William Petruk

Mineralogical and image analysis studies have been performed on four volcanogenic base metal ores that contain 0.01 to 4.5 wt% Pb to determine the behaviour of galena during mineral processing. The galena in these ores is fine grained and is poorly liberated in both the primacy and regrind mill discharges. Consequently, low grade Pb concentrates are produced to obtain relatively high Pb recoveries. The Pb concentrates contain many impurities including high amounts of pyrite and sphalerite, and small amount of CU-, As-, Ag-, Bi-, and Se-sulfides. These impurities need to be rejected from the Pb bullion during smelting. The galena commonly contains up to 1 wt% Ag in solid solution with an average of 600 to 1460 ppu for the deposits studied to date. The Ag in galena accounts for up to 65% of the Ag in some ores.

Jan 1, 1990

By C. -G. Berg, J. T. Tuominen

Since the beginning of the 20th century, energy efficiency in copper smelting has been improved by a factor of 30 as a result of adopting autogenous smelting processes with more and more efficient waste heat recovery systems, increasing use of oxygen enrichment and countless smaller improvements. Nevertheless, energy in the form of electricity and fuels continues to be the biggest contributor to smelter operating cost. Metallurgists around the world are under constant pressure to find ways to save those precious megajoules wherever they can. One area that is often neglected is the removal of water contained in concentrates. Copper flotation concentrates, as delivered to a smelter, typically contain some 8–12% moisture. This moisture must be removed and the only way to do this is by evaporation, which consumes a lot of energy. Several studies have shown that the most efficient way of removing this moisture is to use a steam- heated indirect dryer—the least efficient way being the feeding of wet concentrate directly into a smelting furnace. Even in the most efficient smelters that employ modern steam drying, the energy needed to remove the moisture from the concentrates constitutes over 15% of the total energy consumption of a smelter – acid plant complex. The major steps that have been taken in the past to lower the energy consumption of moisture removal are the use of drying in general and the adoption of steam drying. The energy efficiency of concentrate drying has been improved by 25% over the last 20 years. The latest giant leap in this area, the Kumera Heat Recovery Dryer, is the result of Kumera’s long-term development in improving the efficiency of concentrate drying. The Heat Recovery Dryer is a novel application of steam drying that uses the waste heat from dryer exhaust gas for drying concentrates, thus, cutting the energy consumption by a further 30%. This paper discusses energy consumption in copper smelting in general and analyzes the energy consumption of concentrate drying in detail. Different dryer types are compared especially from the perspectives of energy consumption and environmental emissions. Applicability of different energy sources for drying is evaluated and discussed. The principle of the Kumera Heat Recovery Dryer is presented along with results from extensive continuous pilot plant tests. Potential applications and the feasibility of Kumera Heat Recovery Drying technology are discussed.

Jan 1, 2019

By Shawn P. Coughlin, Michael A. Schimmenti, Juan Leonardo Tello del Pino

"The Sistema de Potabilización Área Norte project (Northern Area Purification System) was a major expansion of the potable water system in Buenos Aires Province, Argentina. The aim of the project was to transport and purify raw water from the Paraná River to provide potable water for five communities in the northern part of the province, benefitting up to two million people. The project was constructed by a joint venture (JV) of four South American contractors and consisted of the following key components:• Treatment plant: A 16-ha (39-acre) area was cleared for the construction of a treatment plant to purify 900,000 m3/day (1.2 million cu ft/d) of raw water from the Paraná River and distribute it to the surrounding communities.• Bored tunnel: Nearly 15 km (9 miles) of 3.6 m (12 ft) inner diameter tunnel, ranging from 18 to 22 m (59 ft to 72 ft) below grade, was bored with two earth pressure balance (EPB) tunnel boring machines (TBM) to draw the raw water from the river. The TBMs started from a central launch shaft and proceeded in opposite directions. Cristina advanced northbound to the Paraná River Intake System, and Liliana advanced southbound to the new treatment plant.• Access and ventilation shafts: Five access shafts and eight ventilation shafts were installed along the length of the tunnel. The access shafts were designed to provide entry points for inspection and maintenance of the final tunnel. The five shafts consisted of one central launch shaft in the middle of the tunnel alignment, one retrieval shaft at each end of the tunnel (intake and treatment plant, respectively) and two intermediate shafts. The intermediate shafts were installed before the TBM passed, with a final liner to be installedafterward."

Sep 1, 2016

By James N. Mure

The paper describes the design development and construction of bored piles at Pindersfield Hospital, Wakefield, U.K. The piles were of monopile type. Monopile is the term used to describe piles which are constructed without pile caps so that the superstructure columns bear directly on the pile top. Pile geotechnical design was developed from the Site Investigation data and testing of two preliminary piles. Final design philosophy is described. Pile structural design was developed from the loadings applied by the superstructure, and the requirements, tolerances and limitations of monopile construction techniques. Construction was closely controlled in order to achieve a ?right first time? result. The conclusion gives a critique of the system and its value.

Jan 1, 2008

By Edward Holloway

The basis for the selection of the ultimate pit for an open pit mining operation is generally opaque. Some form of value-based analysis will generally guide the final decision; however, the value will often gradually plateau whilst the ultimate pit size continues to increase. There is no established framework to guide specialists in the selection of the ultimate pit, with such decisions regularly made on a somewhat arbitrary basis. The key component that is missing from the analyses typically used to select the size of the ultimate pit is risk. Once risk is quantified within the analysis framework, the decision-making range is significantly reduced, and the process for selecting the ultimate pit becomes more consistent, replicable, and defensible. This paper provides an approach to including risk in the process used to select the ultimate pit.

Feb 21, 2024

By M. L. Jeremic

The design of the long-hole sublevel mining method was originally based on the traditional assumption that the principal load was due to the weight of the overlying rock, and that the horizontal stresses are equal to one-third of the vertical stress. However, as mining progressed, the virgin lateral stress was found to be equal to or greater than the vertical stress. The virgin stress in the rock mass is not uniform throughout the folded orebody and adjacent strata. From detailed investigations, three basic patterns of virgin stress in ore panels have been inferred: uniform, bent and twisted. Stresses induced by stoping are up to three times greater than original stresses in the rock mass; they cause heavy ground conditions and make extraction of ore difficult. In the last ten years, the original mining system has been modified several times in order to destress the ground and improve the extraction of ore.

Jan 1, 1978

By Haoran Zhang, Chu Ho

A recent design-build project in New York involved various degrees of additions and improvements to four existing transit stations. Reuse of the existing foundations was considered a more sustainable alternative than constructing new foundations for the project. This approach mitigated the extent of demolition work and limited the amount of downtime for track operations. A key challenge for reusing the existing foundations was the lack of as-built drawings. In order to obtain some measure of confidence for the proposed foundation reuse, non-destructive investigation technology was adopted to evaluate the structural integrity of the piers and foundations. A total of 47 piers for the existing passenger platform were investigated for possible reuse. Several test pits, excavated to verify the foundation type and configuration, indicated the piers were founded on a combination of shallow footings and drilled shafts. Pile integrity tests were performed to verify the length of the drilled shafts. Geotechnical capacity of drilled shafts was evaluated for side friction and end bearing resistance, and confirmed using a proof load test conducted from the existing platform structure. This paper presents the investigation methodology and discusses the approach adopted for geotechnical design of the existing foundations for reuse.

Sep 8, 2021

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

By Jorge Rubio, Gabriel Berkowitz, Fabiano Capponim, Carlos Perez Guerrero, Elves Matiolo, Denise G. Nunes

This paper describes some advances in flotation research in fines (“F” 38 to 13 µm) and ultrafines (“UF” < 13 µm) mineral recovery by two different techniques, at laboratory scale. Extender flotation and flotation with .multi-bubbles. (bubbles with a wide size distribution) of copper sulphide fines (ore feed of about 1 % Cu) were compared with a .standardised. mill laboratory procedure. Comparative evaluation was made through concentrate grade and recovery (size by size results included), .true. (bubbles-particles attachment only) flotation recoveries and process kinetics. Both techniques yielded higher metallurgical efficiencies than the mill standard but better results were obtained with the extender flotation, with emulsified diesel oil (90 gt-1). Concentrate recoveries were of the order of 85-90 % (84 % in standard conditions), 14-17 % Cu grade (15 % Cu in the standard) and 3.5-4.5 min-1 for the Klimpel rate constant (3 min-1 in the standard). Size by size and true flotation results proved that metallurgical and kinetic gains, obtained with the two techniques, might be attributed to fines and ultrafines enhancement. Data obtained are discussed in terms of physical and physico-chemical parameters related to aggregation and capture (of particles by bubbles) phenomena and the practical potential of these techniques are envisaged.

Jan 1, 2003

By Bruce A. Kuyper

Routine core drilling at the Cove deposit failed to confirm gold-silver grades and length of intercepts observed in reverse circulation drilling. A drilling program was designed to ascertain whether the disparity was due to problems with reverse circulation drilling techniques, core drilling techniques, or the erratic nature of the gold-silver mineralization. Special sampling devices and core drilling methods were employed. Data obtained from core-reverse circulation twins showed that down-hole contamination during reverse circulation drilling accounted for much of the variation between reverse circulation and core drill results. Down-hole contamination occurred as a result of high ground-water inflows eroding friable vein material from hole walls.

Jan 1, 1991

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By A. J. Kraemer

[During the past several years a great deal of discussion has centered around the question of the permissible limit of sulphur content in fuels for automotive and aviation motors. Under certain conditions of operation, sulphur in motor fuels causes the formation of corrosive substances which attach bearings, wrist pins, and other parts of engines. On the other hand, in making gas¬oline from certain stocks, the gasoline fraction normally contains a relatively large proportion of sulphur compounds. By the generally used processes of reducing the sulphur content, a significant part of the gasoline fraction is lost as motor fuel, and added expenses are entailed for chemicals, labor, and other process costs. This condition has been an economic burden to some refiners of high-sulphur crudes. In some instances the treating losses have been rather severe and the treating costs relatively high, but the data presented in this paper indicate that the reduction of sulphur content of motor fuel is a problem to a relatively small number of refiners and of little or no concern to the remainder; in fact, more then 90 per cent of the 153 samples analyzed passed the Federal specification requirement, which limits the sulphur content to 0.10 -nor cent. 3 This report is based upon the results of an examination for sulphur content, Doctor test, copper strip corrosion, and color of the samples collected during January, 1930, for the twenty-first semiannual gasoline survey of the Bureau of Mines. The results of the gravity and distillation tests of the survey were published as Report of Investigations 2995. The numbering of the samples given in this report is the same&apos; as in Report of Investigations 2995; for example, No. 25 of this report is the same sample as No. 25 of Report of Investigations 2995.]

Jan 1, 1930

By S. Veeramasuneni

The sign of the surface charge for alkali halides in their saturated brines has been established from non equilibrium electrophoresis measurements and on this basis the flotation response of alkali halides was explained based on the adsorption of oppositely charged collector colloids by heterocoagulation. These surface charge results for alkali halides are generally as expected from simplified lattice ion hydration theory with some exceptions, specifically LiF, KCI, NaCl, KBr, RbBr, KI, and Rbl .The presence of natural oxygen defect states in the crystal lattice and the inaccuracies involved in the gaseous ion hydration free energy values used appear, in past, to be responsible for these deviations. The presence of natural oxygen defect states in KCI, KBr, RbBr, and Rbl as characterized by UV Nis absorption, was found to account for their anomalous surface charge. Further, other positively charged alkali halides, LiF, NaCl and KI, were found to be free of oxygen defect states. Nevertheless, oxygen defects can be created in these alkali halides to make them negatively charged and has been demonstrated for NaCl. Such negatively charged NaCl can be readily floated with positively charged amine collector colloids thus confirming the surface charge/collector colloid adsorption theory.

Jan 1, 1996

By M. S. Prithvi

Over the decades, mine and mineral processing plant operations for the most part, have been found to have had adverse impacts on the environment. At the same time, mineral processing and mining operations produce mineral products that are indispensable to modern society. Thus, the sector has desirable and undesirable attributes simultaneously. The situation presents itself as a contradiction (i.e.) the mineral processing and mining operations are wanted by society, and at the same time unwanted by society. The existing methods of addressing the issues raised above have evidently not been very successful in reducing the opposition to new projects and to the related activities such as land acquisition. This paper attempts to show the relevance and applicability of TRIZ for addressing the issue. TRIZ, or Teoriya Rezheniya Isobretatelski Zadach, is a Russian acronym meaning Theory of Inventive Problem Solving. TRIZ is a powerful tool that can be usefully applied to resolve such contradictions, using resources usually available within the system of interest. Accordingly, this paper introduces the issue background, followed by an introduction to some key concepts of TRIZ such as the 40 principles, separation principles and directed evolution. The paper goes on to apply the 40 principles to two case studies. The results show that TRIZ could be a useful tool to generate potentially innovative and sustainable approaches. Its most appropriate position would be as a supplement to current decision-making procedures, and as a validation tool to review existing solutions for possible improvements. Keywords: minerals, environment, TRIZ, contradiction, resources

Sep 1, 2012

By M. P. Sinha, Rashmi, Tata Steel Ltd., S. Jaiswal, A. Bhatnagar, P. Garg

Reagents form a crucial part of flotation process as they have the power to control the surface properties of minerals. In case of coal flotation, collectors and frothers are two the important and commonly used reagents. But other types of reagents such as promoters, modifiers and depressants are also finding wide applications because of their availability to improve selectivity and increase recovery. Because of these chemicals the scenario has changed from flotation being used mostly for high rank hydrophobic coals to low rank, oxidised or inferior coals. In the present work a case is presented in which two non-ionic surfactants (abbreviated as A & B) known to act as emulsifier have been studied to get a better flotation performance for a preparation plant with varying feed characteristics. Laboratory flotation tests were conducted with both the surfactants using three feed samples of the plant by varying the dosage at three different levels. The highest combustible matter recovery (more than 80%) was obtained for surfactant B at a dosage of 75 ppm (parts per million) for feed 1. But at the same dosage the recovery decreased by 21% and 10.2 % respectively for feed 2 and 3. On the other hand surfactant A showed a consistent result for all the three feed samples giving the highest value at a dosage of 50 ppm followed by a decrease beyond this point. The tests were complemented by contact angle measurements that demonstrated the same trend. In addition to this the reproducibility of data for Surfactant A was checked and found that the standard deviations for both separation efficiency and combustible matter recovery were within the permissible range (less than 5%). Finally an in-plant process optimization study to evaluate the performance and applicability of surfactant A at industrial level was done and has been discussed.

Jan 1, 2016

By Dakota D. Faulkner

Cable bolts anchored with traditional two component polyester resin cartridges have successfully supported difficult roof conditions in underground mines. Resin cartridges provide a costeffective cable bolt anchoring system with consistent anchorage performance characteristics when properly installed. The most commonly used cable bolts in the U.S. mining industry are 270 ksi (1,862 MPa), 0.7 and 0.6 inch (18 and 15 mm), seven-strand smooth cable with resin mixing bulbs (also known as bird cages), and 40- and 30-ton nominal capacity, respectively. However, there are other types of cable bolt anchoring systems aside from bird cages. Recently, many questions have been raised regarding the anchorage characteristics of various types of cable bolts. Keystone Mining Services, LLC (KMS), the affiliated engineering company of Jennmar Corporation, conducted a variety of controlled tests developed to closely model actual underground installations. These tests compared the performance of three commonly used cable bolt varieties, including plain, bird caged and indented seven-strand cable. Details of the laboratory testing and comparative analysis of the results are provided.

Jan 1, 2013