Search Documents

By H. N. Dunning

A comprehensive production research program, now in progress at the Petroleum Experiment Station of the Bureau of Mines at Bartlesville, Okla., includes studies of the displacement of petroleum from sand by detergent solutions. An earlier report (12)2/ presented the results of an extensive research program to determine the value of detergents as floodwater additives. This report presents later results of the detergent-testing program (13, 17). Although water-flooding methods and controls are constantly being improved to increase the production of oil from secondary-recovery operations, considerable crude oil commonly remains.in place after a water flood has been terminated. Therefore, the possibility of improving the efficiency of a waterflood by the use of detergents is of increasing interest. The effects of many substances on the efficiency of water flooding have been investigated in laboratory studies (5, 11, 13, 17, 19, 24). Of the various sub-stances tested, only surface-active agents were consistently effective in removing oil from sand. Results of laboratory studies presented in earlier reports (9, 11, 12, 13) show that many detergent solutions effectively displace petroleum from sand surfaces under varying conditions encountered in centrifuging, manual and mechanical agitation, ultrasonic vibration, and imbibition.

Jan 1, 1957

By Adnan A. Malik, Tadashi Maejima, Jiro Kuwano

"Previous studies revealed that the helix deflection reduced the end bearing capacity of screw pile in dense ground even if the installation process is completed with minimal soil disturbance. The ultimate end bearing capacity in dense ground is difficult to achieve during the full-scale pile load test due to the limitation of the loading system. Therefore, in the present study, model scale of testing is selected to investigate the effect of helix deflection on load settlement behavior of single helix screw pile under increasing stress level. It is observed from the test results that the applied surcharge pressure, which is used to simulate the effect of stress level, is decreased with increase in model ground thickness. This decrease in the stress level is due to the frictional resistance between the container wall and sand. It is also observed that the end bearing capacity of screw pile increases with the increase in stress level but at gradually decreasing rate. The test results indicated that the helix deflection during the pile load test should not be more than critical deflection (0.72 mm average) of the helix to avoid any reduction in the end bearing capacity of screw pile. The helix deflection, which is measured after the pile load tests are also compared with the equations of flat circular plate having uniformly distributed load over the plate with simply supported and fixed inner edges.INTRODUCTIONThe screw pile consists of a central steel shaft with one or more helices attached at different location on the central shaft. The installation mechanism of screw pile consists of torque and pushing force. The screw pile installation mechanism can affect the unit weight of the ground during its installation. This effect is small in cohesive soils but it is quite noticeable in loose to medium dense sands (Adams 2011; Santos et al. 2013). The pushing force should be controlled in such a manner that pile penetration should be at least 80% of the pitch of the helix, during each revolution (Perko, 2009)."

Jan 1, 2017

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By F. R. McDonald

The proton NMR spectra of 32 pyridines in two solvents, carbon tetrachloride and benzene-d6, are presented. The chemical-shift and differential-shift values are correlated with the substitutent position and with the solvent media. The ring protons and the protons on alkyl substituents are tabulated. The paramagnetic shift of the protons adjacent to the nitrogen is discussed, and a proposed structure for the pyridine-benzene complex that is consistent with the observed anomalous paramagnetic shift is presented. The utility of the data in the identification of pyridine compounds found in shale-oil naphtha is demonstrated.

Jan 1, 1971

By I-H. Jung, J. Kim, B. Konar

"The usage of FeNdB permanent magnet, containing Rare earth elements (REEs), is steeply increasing with its demand for wind-turbine and electrical vehicle. The improvement and recycling of the permanent magnet require good understanding of chemistry of all constituent elements. In order to understand the chemical interactions between REEs and Fe, all Fe-RE binary systems have been critically assessed and optimized based on reliable literature data. The Modified Quasichemical Model and Compound energy formalism is employed to model the liquid phase and the solid solutions present in the binary systems respectively. The enthalpy of the liquid and the intermetallic phases showed a systematic trend along the lanthanide series. This helped to mitigate the discrepancies in literature data and also to predict the binary interactions between some less well investigated Fe-RE binary systems. INTRODUCTIONRare Earth elements (REEs) are a group of seventeen elements (including Scandium, Yttrium and the lanthanide series) that exhibit same characteristic chemical and physical properties. These properties make them valuable to the electronic, appliance, green technology, weapon and medical device manufacturing industries. Compounds of REE with other metals (like Co, Fe, Ni etc.) have unique properties of luminescence, thermal and electrical conductivity, magnetism and ability to act as catalysts and polishing compounds (Gschneidner ,2011).They are not only indispensable for some electronic gadgets of today, like computers, music systems, mobile devices, televisions and MRI machines, but also holds a key to more greener technology of the future. They contribute to the development of more efficient and environment friendly version of everyday products such as cars and light bulbs. REE compounds revolutionized the magnet industry by making them smaller and more powerful with increased longevity, and high temperature workability, which are used in motors and generators that power electronics, telecommunications, electric automobiles and turbines(Humphries, 2011)."

Jan 1, 2012

By Manoj Khandelwal, Jian Zhou, Yingui Qiu, Peixi Yang, Pingan Peng

Rockburst prediction is crucial in deep hard rock mines and tunnels to make safer working conditions. Due to the complex interaction of many factors involved in rockburst prediction, such as multi-variable and multi-interference factors, three hybrid support vector machine (SVM) models optimized by particle swarm optimization (PSO), Harris hawk optimization (HHO), and moth flame optimization (MFO) are proposed to predict rockburst hazard level (RHL). The RHL is determined according to four kinds of microseismic characteristic parameters including angular frequency ratio, total energy, apparent stress, and convexity radius. Then, six types of microseismic characteristic parameters are taken as input variables in 343 sets of data, including angular frequency ratio and total energy, etc.. And the RHL is taken as the output target of rockburst prediction. The classification performance of PSO-SVM, HHO-SVM, and MFO-SVM hybrid models is evaluated by accuracy (ACC), precision (PRE), and kappa coefficient. Findings reveal that the MFO-SVM model performs best in terms of accuracy, with ACC, PRE, and kappa coefficients reaching 0.9559, 0.9063, and 0.9094 respectively, while PSO-SVM and HHO-SVM have similar performances. However, the PSO-SVM, HHO-SVM, and MFO-SVM all perform better than the unoptimized SVM model. This confirms that the three optimization algorithms significantly enhance the rockburst prediction capacity of the SVM model to help mine practitioners apply machine learning methods to rockburst prediction problems appropriately.

Feb 3, 2023

An Engineers&apos; Symposium was held Wednesday evening, Mar. 26, in the auditorium of the Engineering Societies Building, 29 West. 39th St., under the general auspices of the Local Sections of the American Institute of Mining and Metallurgical Engineers, American Society. of Mechanical Engineers, and the Society of Automotive Engineers. It was participated in by members of the American Institute of Electrical Engineers, American Society of Civil Engineers, American Chemical Society, American Electrochemical Society, American Institute of Chemical Engineers, American Society of Heating and Ventilating Engineers, American. Society of Refrigerating Engineers, New York Electrical Society, Brooklyn Engineers&apos; Club, Illuminating Engineering Society, Institute of Radio Engineers, Municipal Engineers of the City of New York, Society de Chemie. Industrielle, Society of Chemical Industry, and the Society of Naval Architects and Marine Engineers. In opening the meeting the chairman, Gano Dunn,* said: The program calls this an engineers&apos; symposium, which means a putting, together of things, and these things tonight are ideas of fundamental relations to the engineering profession and the engineering societies. Not only engineers, but all men nowadays are examining their views in respect to their relation to what we call Society. My conception of Society is that there is no such thing in the concrete sense of the word. It is an abstraction, and just in proportion as it is a generalization and broader in scope than the particulars from which it is drawn, so is it emptier of content. That does not mean that it is not important, but it does mean that we should be careful and not be led astray into a zeal for doing things for Society that we would not do for our fellow engineers and our brothers. The man who is unwilling to do something for his brother or fellow engineer and yet urges that same thing for Society-is thoroughly inconsistent and, in my opinion, wrong.

Jan 5, 1919

By C. E. Baltzer, W. H. Harper

"This study has been developed to illustrate the trend and pattern of distribution applying to the quantities and costs of the fossil fuels used, and the related amounts of electricity generated, in the thermal segment of the Canadian electric utility industry.Traditionally, Canada's requirements for electric energy have been preponderantly met by hydraulic power. The need for augmented supplies of thermally generated power has mainly developed since the close of World War Il-in an era that has seen drastic decline in the production of indigenous coal and buoyant expansion in the supply of oil and natural gas. Although coal currently is faced with serious competition from the fluid fuels, the utility industry in particular promises an advancing market for coal, because of its abundant resource, at prices less likely to show sharp increase. For Canada as a whole, this trend has been progressive since 1959, and, unbelievable as it may now seem, the extent of the advance by 1975, particularly in Ontario and the Prairie Provinces, may well be as much, or even more, than the present rate of consumption for all purposes.The text and the tables and charts are arranged to focus attention on: the growth of thermal genera ting capability; the historical trend in consumption of fuel and the related production of electricity; patterns of distribution by types of fuel and thermal capacity; the relationship of steam to other sources of thermal capacity; and the quantities, costs and related percentages of electricity generated by types and kinds of fuel used, both regionally and provincially."

Jan 1, 1966

By H. B. Hill

The Salt Flat field, formerly called the Joe Bruner field, is located northeast of the town of Luling in Caldwell County, Tex. This field, which is a fault structure, approximately parallels and is about 5 miles east of the Old Luling field. The proved area is approximately 1,280 acres, on which 332 producing wells (September, 1930) have been drilled. The majority of the wells are producing from the Edwards limestone at an average total depth of 2,700 feet. A few wells are producing from the Austin chalk or from other formations above the Edwards limestone. The Wilcox formation is exposed, and the fault trace in places is scarcely evident. The strike of the structure is approximately N. 20 to 45° The displacement of the fault is probably 200 to 500 feet. The discovery well was completed in the Austin chalk by the Lutex Oil Co. during April, 1928. In October, 1926, the Sun Oil Co. completed the discovery well in the Edwards pay. This well was an important discovery, as it indicated the potential oil possibilities of the Edwards limestone in echelon fault structures. The discovery led to the development of the third fault field in the Edwards limestone and opened up a large area for future prospecting.

Jan 1, 1931

By Richard S. McCaffery, Morrison B. Yung

While assaying some copper carbonate ore from the Frazer claims, Similakameen, B. C., I noticed that on parting the gold button a deep orange solution was formed. The button gave off pink bands in the nitric acid, which became deep orange at a short distance from it; and as it traveled over the surface of the porcelain dish, it left a deep orange track behind. As the button brightened in the cupel, it appeared to have a bronze color; but I have since found that when amarillium is in large excess of the gold, the button is a very dark gray. The button parted easily. To the orange solution I added a salt (NaCl) solution, shook in a silver testbottle, and filtered. With H2S I obtained a precipitate, which I supposed due to platinum. However, on further tests, it did

Jan 1, 1903

By Jose Bengoa

Low metal prices and environmental restrictions are always a challenge for copper smelters operation and its productivity. Thus, in order to reduce production costs and control gas emissions, improvements of the Teniente Converter (CT) operation were made at 110 Smelter Plant of Southern Peru Copper Co., 110, Peru, and the main objective was to increase its capacity for smelting copper concentrates without affecting normal operation. The present work corresponds to a recent study conducted during the normal industrial operation of the Teniente Converter in this plant and, it shows the effect of increasing air oxygen enrichment from 28 to 34% on its productivity. The results show an increasing of concentrate smelting rate from 800 to 1370 tpd and hence a notorious improving in copper production, and practically no effect on the refractory consumption. The increment of the concentrate throughput, increases also the SO2 concentration and the sulfuric acid production, showing the effort done by this operation in order to accomplish the environmental Peruvian regulation.

Jan 1, 2003

By N. Magdalinovic

Generally speaking, erosion, as a process which entails degradation of surface layers of earth under the influence of the mechanical energy of surface waters, and from the point of view of biosphere sustainability, is a harmful process. This is absolutely true when agricultural and forest areas are concerned. However, if erosion is viewed selectively, this general definition about its harm raises serious questions. In other words, the erosion which takes place in the terrains where there is no vegetation because of the geological composition of the soil, does no harm. On the contrary, if the mineralogical composition of such terrains is characterized by a presence of precious and rare metals, erosion can be very useful. It contributes to the creation of new alluvial deposits of these metals in the waters in the plain land. It is here that torrents from hills come down and cause erosion. And finally, if there were no erosion, there would be no renewable deposits of gravel and sand.

Jan 1, 2007

By Lloyd Williams

A vertical air shaft in the Birmingham, Ala., iron district was sunk with a circular cross section and lined with concrete at a relatively low cost to provide needed ventilation for an iron-ore mine. The method of sinking the shaft is described, and the costs are stated in mar-hours with a descriptive list of equipment and a statement on the size and use of temporary buildings. Preparation began May 2, 1955, and the shaft was completed at a depth of [680] feet by September 22, 1956. By October 1956, all temporary building and [aft]-sinking equipment had been removed. The total direct-labor cost for the operation, including preparation and dismantling, was 50,700 man-hours, or 30.2 man-hours per foot. Total rock and dirt removed amounted to 17,523 cubic yards (in place), and the shaft lining required 4,635 cubic yards of concrete to form a circular air shaft with an inside diameter of 16 feet.

Jan 1, 1960

By Todd Kilduff, Paul Wilkinson

Microtunneling is rarely a straight forward “business as usual” endeavor. More often than not, these projects take twists and turns that require on the fly, out of the box solutions to get the project completed. This paper is a case history of a 63-inch diameter, Permalok, microtunneling project, extending nearly 700 linear feet under a hill forming the left-hand abutment to an earth embankment tailings dam. The job had three major and unexpected challenges that required unorthodox solutions. Challenge #1— Face Configuration: The Santiago Formation, a cemented sand formation with widely varying strengths, presented a challenge to configuring the face with regards to the number and length of pics and cutters. Subtle differences in type and size of the tooling had a big impact on the performance of the machine. Challenge #2—Eccentric Loading: Issues at the launch shaft with the Permalok pipe adaptors caused eccentric loading on the casing pipe. This issue resulted in overstressing and breaking of several pipe joints that ultimately led to seizure of the tunnel. Challenge #3—Back-tunnel Excavation and MTBM Recovery: There were many detailed considerations into excavating a recovery tunnel to retrieve the MTBM, especially being under a high hazard earth embankment dam.

Jun 13, 2021

ABSTRACT This paper details the work of RISKGATE, the largest Australian Coal Association Research Program (ACARP) occupational health and safety initiative to date. The program is an interactive online risk management system developed to maximize health and safety performance in the coal mining industry by implementing continuous improvement in managing major unwanted events. The comprehensive knowledge base covers tires, collisions, fires, isolation, strata control underground, ground control open cut, explosions, explosives, manual tasks, and slips/trips/falls. All major Australian coal mining companies contributed topic experts to this broad industry initiative: nine coal mining companies, more than 80 experts, and more than 400 days of individual time for knowledge-capture workshops.

Jan 1, 2014

By Anna Gustafson, Sohail Manzoor, Håkan Schunnesson

Sublevel caving operation relies on the estimation of ore grade at drawpoints, as the mine management uses grade to decide whether the material at a certain ring should be loaded or abandoned. Grade is estimated in various ways, including visual estimation, density-based calculation, and sampling and assay methods. The grade estimation at the world’s two largest underground iron ore mines owned by LKAB in northern Sweden is based on the density difference between ore and waste. The calculations assume a constant swell factor, a theoretical fill of 100%, and a linear relationship between bucket weight and material grade. This study evaluated these assumptions in detail based on the loading data for 12,237 buckets and concluded that the method has some shortcomings which render the assumptions invalid. Further research is required to deal with these shortcomings to improve estimation of the material grade.

Oct 17, 2022

By I. Chatterjee

The application of microwaves has a demonstrated potential for the ultimate removal of water from fine coal. The principle of microwave drying of fine coal is based on the selective absorption of microwaves by water. Coal is a poor absorber of microwaves. As a result, water can be removed from fine coal by selectively heating water molecules. One of the difficult problems drilling microwave heating is the exact determination of temperature in the core of the materials. The electromagnetic energy absorption in coal/water mixtures during microwave drying is controlled by several factors including the dielectric properties of the constituents. In this paper the dielectric properties of various ranks of coal are presented as a function of frequency and moisture content. The measured dielectric data are incorporated into electromagnetic and thermal models of coal which predict the energy absorption and temperature distribution during microwave heating.

Jan 1, 1990

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By Arthur L. Crawford

PLAGER gold is perhaps the most difficult of the common mineral deposits to evaluate. Not only are the erratic pay streaks a source of never-ending uncertainty, but the spotty distribution of the gold in iso¬lated nuggets is a perpetual source of error and disappointment to the sampler. Experienced engineers have long realized this difficulty and have been wary in predicting assay values except in the most general terms, and then only after extensive and usually expensive sampling. During the past year I have had the opportunity of checking a number of gold placers, and from the results obtained I believe that the microscope may be employed to advantage in placer sampling.

Jan 1, 1933

By Mansoor Barati, Yindong Yang, Yonggang Wei, Bo Li, Alexander McLean

Reduction roasting followed by magnetic separation is an important method for treating laterite nickel ores. In this work, garnierite type laterite ore from Yunnan province in China was reduced by methane under different conditions followed by magnetic separation to obtain the ferronickel concentrate. The phase and microstructure transformations of garnierite in the reduction process were investigated using XRD and SEM-EDS. The experimental results showed that reduction temperature from 873 to 1173 K had only a small effect on content and recovery of nickel and iron. The content and recovery of nickel and iron in the concentrates increased slightly with prolonging reduction time. In addition, the nickel and iron content decreased with increasing methane concentration, but the recovery of nickel and iron increases. A decrease in the iron content and recovery were observed when the dosage of sodium sulfate varied from 5 to 20% at a temperature of 1073 K and reducing time of 90 min, while the nickel content and recovery gradually increased.

Mar 1, 2018