Search Documents

By R. Stefaniuk, T. Le, J-Y Huôt, H. Henein

"One of the most important process variables in gas atomization is the gas to metal (G/M) mass ratio as it has a direct effect on the mean particle size of the atomized powder. If this ratio can be controlled during the atomization process, the powder produced would be more uniform and the d50 more predictable. Thus, atomization using a tundish or gravity feed from a crucible would be more stable. In gas atomization, the gas flow rate can be easily monitored; while it is very difficult to determine the molten metal flow rate. This research paper presents a new method of recording the molten metal height with time using a conducting metal height detector. The metal height recorded in real time during atomization was used to characterize using a model the friction losses in the metal delivery system. It is found that the integrity of the metal delivery tube and the cleanliness of the melt play a key role in the maintaining a stable metal feed.IntroductionIn the gas atomization process, molten metal is normally fed to the system either continuously using a tundish or in most cases a certain amount of metal is melted in a crucible and flows into the atomizing chamber under gravity. In the first case, the metal flow rate is believed to be constant during the atomization process despite the presence of slag or dross on the molten metal surface. In the second case, the amount of molten metal is depleted with time and the rate at which the metal flow decreases with time varies from test to test in a seemingly unpredictable fashion.' Furthermore, most atomization systems are confined units and the metal level in the crucible cannot be detected by a visualization method. In industry as well as in laboratories, the metal flow rate is normally calculated on either the mass of input material or the mass of total production divided by the duration of the test. This figure is not accurate enough and obviously cannot be used as a control parameter for the gas to metal ratio as it is only determined after the completion of an atomization run. The need exists for a metal flow rate measurement and control methodology; thereby the d50 of the powder produced may be estimated and controlled in real time. Clearly, the smaller the variation of the G/M ratio during the atomization process the more uniform the powder produced and hence the size of the particles can be predicted."

Jan 1, 1994

Comalco Limited has recently completed construction of a $50 million kaolin plant at the site of its bauxite mining and industrial minerals operations at Weipa. The plant will produce 100,000 tonnes per annum of coating grade kaolin for the paper industry.Comalco produced the first coating kaolin from the deposit in 1979 on a trial basis. Since then a variety of quality coating grades with specific particle ize distributions and brightness values have been prepared.Extensive drilling and bulk sampling of the deposit over eight years has shown that the orebody is large and of a high grade suitable for the production of premium quality coating kaolins.The processing plant technology was developed by Comalco in association with the European kaolin and equipment producer Amberger Kaolinwerke GmbH (AKW).The Weipa kaolin plant is the first of this size to be built in the Pacific Basin region and it will offer the region's paper-coating mills a stable and reliable source of high-quality kaolin, shipped from an established bulk loading port. The paper provides an overview of the development of the kaolin investment, the nature of the production process and details the project management procedure used for the design, construction and commissioning of the plant. Three areas of significant interest, the gas turbine fired pray dryer, the moving bridge shiploader and the use of aerobelt conveyors on the project are detailed.

Jan 1, 1988

CRUSHING and concentration flow-sheets of western mills have become greatly simplified and more or less standardized of recent years with the introduction of modern grinding methods and flotation. Improvement has not stopped, however, and advancement is continually being made in crushing and milling practice. A case in point, where remarkable improvements in efficiency have resulted from comparatively minor changes in the flow-sheet, is in the New Cornelia mill of the Calumet and Arizona Mining Co. at Ajo, Ariz. This mill, completed in 1924 for the concentration ,of the sulfide ores of the New Cornelia mine, was originally designed for a 5000-ton capacity. Before recent changes and additions were made the five 1000-ton units were handling 6500 to 7000 tons per day, giving a flotation feed of approximately 14 per

Jan 1, 1930

A broker relies heavily on mineral valuations and independent experts' reports to provide the fundamental information, both technical and commercial, which provides the basis of estimating the sharemarket value of securities and underlying assets. It is important to appreciate the significant variance that can occur between the market value and other types of valuation at a particular point in time. In general, most experts' reports and valuations seek to provide estimates of technical/fundamental or ""fair"" value which correspond to the Corporations Law and accounting standards requirements. They do not usually attempt to estimate (stock) market values and it is usually and quite correctly the broker's task to estimate market values on the basis of a technical appraisal and consideration of all other commercial, market and financial influences. Therefore ideally, an independent experts' report or information memorandum will include material relating to commercial and management aspects of a company as well as detailed technical reviews and fundamental valuations. Wherever sensible cash flow projections can be made, cash flow-derived valuations, usually based on discounted cash flow (DCF) calculations, remain the preferred valuation methodology. Brokers in general would not argue with this preference. However, there is a paucity of examples of valuations where alternative methods are applied as a check on the reasonableness of a DCF-based estimate.

Jan 1, 1994

By Jan Lückhoff

The introduction of the EAF Quantum furnace by Primetals Technologies represents an important milestone in the field of electric steelmaking during the last 15 years. In this process the latent and chemical heat of the off-gas generated during a melting process in an EAF is used to pre-heat scrap in an integrated shaft prior the melting of the scrap in the vessel. Combining proven own technologies, Primetals EAF Quantum enables nearly continuous process, cutting down idle times and enhancing availability for production. The essential benefits will be shown in this Paper.

Aug 16, 2017

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1956 was made under a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 120 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1956 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 17 producers of aviation jet fuels are represented.

Jan 1, 1957

By C. M. K. Boldt

The Bureau of Mines studied the compaction characteristics of metal and nonmetal tailings. Densities of the tailings and zone of compaction influence, compactive effort, and cost of equipment are related to changes in the factor of safety for specific grain-sized tailings and embankment configurations. Field testing was accomplished in two distinct phases. The first phase investigated the effectiveness of using a nuclear gauge on metal and nonmetal tailings to produce rapid, instantaneous measurements of moisture content, wet density, and dry density. The results of the nuclear gauge testing are presented in chapter 1. Chapter 2 presents a comparison of the compactive effectiveness of three different pieces of construction equipment on a coarse-grained metal tailings pond. The three pieces of equipment chosen for study were a DBH track-mounted dozer, a DSOO rubber-tired dozer, and a SP848 vibratory smooth-drum compactor.

Jan 1, 1985

By Duk-Wom Park

INTRODUCTION he most important information required for the engineering design of structures in rock is its inherent rock properties. Without providing adequate parameters on the rock property, high quality of the engineering design cannot be expected. Many laboratory rock testing methods have been developed, but they are mostly for testing intact homogeneous rock without appreciable discontinuities. In reality, the intact rock properties do not represent the behavior of rock masses because rock masses include irregularities such as joints, cracks, interlayers, variations in mineral compositjon, etc. In general the type and intensity of the rock defects may be much more important than the type of rock which will be encountered (Terzaghi, 1977; Bieniawski, 1984). In-situ rock testing can provide better information on rock parameters, but it takes a tremendous amount of effort, time and cost. In recent years, numerical modeling techniques are gaining popularity as a design tool for structures in rock bodies due to the enormous progress in computer technology (Wang, 1985; Kripakov and Melvin, 1983; Park and Ash, 1985), but it is quite dangerous to use numerical techniques without having proper input data. Bieniawski (1984) states as follows: Some design methods such as numerical techniques have outpaced our ability to provide the input data necessary for the application of these methods. In order to provide an adequate amount of input data, an extensive testing program may be required, thus major efforts in time and expenses are commonly spent, In this paper, a new rock testing method, which utilizes the principles of laser holographic interferometry, is introduced. This method requires only a few minutes to measure the modulus of elasticity and quality of a rock core sample, which does not have to be cut or ground. The Poisson's ratio can also be measured in a few minutes from a sliced rock specimen. HOLOGRAPHIC INTERFEROMETRY Principles of Holographic Interferometry In 1948, Gabor invented holography, which is the technique of reviving three dimensional images using a monochromatic light source. A full demonstration was not made then because a clean monochromatic light source was not available. Later, in the early 19601s, the laser was adopted as a monochromatic and coherent light source (Leith and Upatnieks, 1963). Since then, applications have been made in many different fields ranging from crime prevention to three dimensional television. In this technique, an image is usually recorded by means of constructing a hologram which is a record of the interference pattern formed on a high resolution photographic system as shown in Figure I. A beam splitter divides the laser beam into two beams: (1) an object beam which is expanded while passing through a beam expander and illuminates the object, and (2) a reference beam which is expanded and illuminates the holographic plate. Subsequent to an exposure, the holographic plate is developed and illuminated by the expanded reference beam. The original scene of the object is revived in a three-dimensional image. The entire instrument should be placed on a vibration free environment. The wave fields reflected by the object in two slightly different configurations can be superimposed to form an interference fringe pattern. Thus, it is possible to measure the displacement that took place between the two configurations. This method is called holographic interferometrv. There are two methods of achieving this phenomena. The first is the double exposure method, wherein two exposures of the object are made prior to developing the film. The first exposure represents the original condition and the second, the disturbed condition. The second method is the real time holographic method. In

Jan 1, 1986

By C. R. Hubbard

The Bureau of Mines investigated the mineral resources of the Upper Missouri River Basin as a part of a comprehensive water and related land resources study by six Bureaus of the Department of the Interior, coordinated by the Department's Missouri River Basin Field Committee. The mineral resource study covers an area of about 18,000 square miles within the Great Plains physiographic province of central Montana. Exposed Formations in the plains are chiefly flat-lying Cretaceous sediments. Plutonic rocks crop out in the central parts of the mountain uplifts, with steeply tilted Paleozoic sediments exposed around the margins. Oil and gas have been produced from several fields in the study area; total value exceeds $45 million. Coal-bearing formations of Upper Jurassic and Cretaceous age cover approximately 45 percent of the study area. Total production of coal since 1880 has been between 40 and 50 million tons, exceeding $75 million in value. Total metal production has been about $52.5 million. Industrial mineral production from 1925 through 1960, is valued at $24 million.

Jan 1, 1964

By Alice M. Chieruzzi

This Country Documentation Report presents the development of economic indices for the Philippines for the period from 1970 through 1981. The work was done through the Bureau of Mines, Minerals Availability Program, under Contract number J01225001. This contract calls for the development of twelve index time series describing factor input costs in the mining sector of 95 countries. The twelve index time series describe the costs of: 1) mining wages, 2) construction wages, 3) equipment and repair parts, 4) bits and related steel, 5) eimber and lumber, 6) fuel, 7) powder and balsting agents, 8) tires, 9) construction materials, 10) industrial materials, 11) transportation, and 12) electrical power. These indices combined with weight factors being developed by the personnel of the Minerals Availability Field Office (MAFO) of the Bureau of Mines in Denver, Colorado, will be used to perform instantaneous updates of all costs relating to the mining industry. The indices were developed primarily for use in the Bureau's Minerals Availability Program in assessing the worldwide availability of nonfuel minerals.

Jan 1, 1983

By Karen J. Dawson, Francisco Johnson

"Pressure-grouted high strength helical displacement piles are a recently developed pile type that can be useful in conditions where noise or vibrations must be low or where access or clearance is limited. However, there is no information in the literature that can be used to estimate the soil resistance of these piles or production rates. To fill this information need, this paper presents a New Jersey installation case history and the results of static axial and lateral load tests on both pressure-grouted and ungrouted high strength helical piles at the case history site and trial installation locations in New Jersey and Washington State. Piles between 25 and 50 feet long comprised of steel shaft diameters of 4.5, 5.5, and 7 inches with equivalent grout column diameters ranging from 12 to 22 inches were tested. Lateral loads of up to 100 kips and axial compression loads of up to 700 kips were applied. The results of the load tests are compared to predictions of lateral deformation and axial resistance.INTRODUCTIONHelical piles have long been recognized as a useful foundation type in situations where noise and vibrations must be limited, or where there are access or clearance restrictions. Relatively well-documented design methods and torque to capacity correlations have been developed for the most commonly used helical piles, which are relatively small (typically shafts of 6 inches or less) with corresponding low load carrying resistance.With the increased need to construct in congested urban environments, there is incentive to develop helical piles with higher axial resistance. Seismic and other loading conditions also require lateral resistance, which is low for the typically small helical pile shafts. One method of increasing the soil resistance, both axially and laterally and at relatively low cost, is to place grout around the shaft. Injecting the grout under pressure through the hollow helical pipe section and out a grout port or ports located near the toe of the pile has the potential to increase the pile resistance significantly above that which can be achieve by gravity grouting. Not only does the pressurized grout push out against the surrounding soil, but the rotating helix helps to distribute the grout laterally. Unfortunately, little information is available in the literature to help designers estimate the resistance of grouted helical piles in general and none is available regarding pressuregrouted helical piles."

Jan 1, 2016

By M. Javier

In business mining, dilution is the result of the operating parameters that occur too often and cause serious consequences to mine performance, questioning TO WHOM BENEFITS DILUTION. Mining persists in changing perception of real meaning of dilution. The lack of interrelation between mineral processes and nature compromises the understanding of dilution; this absence of interrelation occurs due to the misinterpretation of nature, otherwise, Geomimic could be helpful to filling the gap of misinformation. NATURE provides LIMITED metals in low content deposits; it is a challenge to obtain them. Nature never considers dilution. Furthermore, though dilution is a human concept, dilution is accepted and promoted. Reality of dilution is in its errors accumulation that translates into technology level or status applied in nature. It is doubtful that dilution can continue surviving if it is ?meaningless?. It will discourse: Is dilution illegal? If the change occurs in the prediction of mining will prevail a different destiny, it is important to touch the cores of the business; otherwise, it would represent repetition of the same ?negative? effects, as usual. Mining defines many losses during the disturbance of nature, from NPV elaboration to the metal recovery to commerce, demanding BETTER DESIGN. This paper introduces and applies MANAGEMENT BY LOSS, as first steps, to limit risks and uncertainties in mining. As result, the management of dilution will be obtainable under mining practices which promotes its character of SUSTAINABILITY.

Feb 23, 2014

By T. S. Golosinski

"This paper reviews the types of selective continuous miners (SCMs) available at present, and compares their main features. Furthermore, operating practices and mine planning aspects of the SCMs applications are reviewed and conditions for efficient application of this equipment are defined. Finally, the potential applications of the SCMs in surf ace mining of oil sands are discussed INTRODUCTIONIn the 1970s the United States Bureau of Mines (USBM) conducted a program of investigations, design and demonstration of various continuous surface mining concepts, This included continuous mining equipment which was an adaptation of several civil engineering and/or underground mining machinery concepts to surface mining. Upon termination of this program, the related development was continued by a number of equipment manufacturers, leading to development of several types of SCMs. This new type of surface mining equipment is able to mine selectively hard and thin multi-layered formations at high, sustained, and economically viable production rates.While used mostly in coal mining at present, the characteristic features of this equipment permit conclusion that it may prove to be an efficient tool for surface mining of oil sand, and/or related overburden stripping. Of particular interest here may be the ability to mine thin layers of hard material, without a need for its earlier fragmentation, and the ability of the SCMs to load a variety of haulage equipment, including belt conveyors."

Jan 1, 1989

By D Maschemeyer

The cobalt production of the Chemical Metallurgical Division of Sherritt Gordon Mines Limited was supplemented, from May, 1962, to June, 1964, by processing 3,500 tons of a calcined cobalt-nickel concentrate. This paper describes the reduction roast -aqueous sulphuric acid leach process and the operating practices employed in recovering cobalt, nickel and copper from this oxidized by-product of a lead-copper operation. Incorporated in this paper is a description of how this process was integrated with the existing ammonia leach -hydrogen reduction process for the recovery of nickel and with the soluble cobaltic ammine process for the recovery of cobalt. Introduction T HE Chemical Metallurgical Division of Sherritt Gordon Mines Limited at Fort Saskatchewan, Alberta, has recently completed ten years of operation utilizing the ammonia leach process for the recovery of nickel, cobalt and copper from sulphide concentrates, matte and other materials amenable to this process. A continuing development program, along with the expansion of certain facilities, has enabled the refinery to attain a production rate of 31, 000,-000 pounds of nickel per year by hydrogen reduction. This represents an increase of approximately 85 per cent over the original design capacity of the plant.

Jan 1, 1965

By Karl R. Zipf

A tube bundle system (TBS) is a mechanical system for continuously drawing gas samples through tubes from multiple monitoring points located in an underground coal mine. The gas samples are drawn via vacuum pump to the surface and are typically analyzed for oxygen, methane, carbon dioxide and carbon monoxide. Results of the gas analyses are displayed and recorded for further analysis. Trends in the composition of the mine atmosphere, such as increasing methane or carbon monoxide concentration, can be detected early, permitting rapid intervention that prevents problems, such as a potentially explosive atmosphere behind seals, fie or spontaneous combustion. TBS is a well-developed technology and has been used in coal mines around the world for more than 50 years. most longwall coal mines in australia deploy a TBS, usually with 30 to 40 monitoring points as part of their atmospheric monitoring. The primary uses of a TBS are detecting spontaneous combustion and maintaining sealed areas inert. The TBS might also provide mine atmosphere gas composition data after a catastrophe occurs in an underground mine, if the sampling tubes are not damaged. TBSs are not an alternative to statutory gas and ventilation airflowmonitoring by electronic sensors or people; rather, they are an option to consider in an overall mine atmosphere monitoring strategy. This paper describes the hardware, software and operation of a TBS and presents one example of typical data from a longwall coal mine.

May 1, 2013

By Culver, Richard S.

In spite of the widespread interest in rock bolt research, relatively little is known about the critical region surrounding the bolt anchor. In analyzing the stress distribution around an opening resulting from rock bolt support, it is commonly assumed that the bolt is fixed at a point far enough from the surface so that the anchor does not influence the performance of the bolt. Furthermore, a bolt anchor is assumed to per- form satisfactorily if it will hold the design load with a minimum amount of load relaxation, commonly called bleedoff. From the standpoint of the design engineer both of these assumptions are reasonable, but they ignore the fact that the extremely high stresses in the region of the anchor are capable of generating fractures in the rock. Lang estimated the bearing stresses for a slot and wedge anchor on a one-inch-diameter bolt to be as high as 125,000 psi. This paper describes a more thorough analysis of the magnitude of the stresses around the anchor and the nature of the potential fractures that might result.

Jan 1, 1968

By H. P. Kritzinger, T. C. Kingsley

Rotary kilns are used for a variety of mineral processing operations. Hatch makes use of a kiln model developed from first principles to evaluate designs for its clients. This tool has been applied to a variety of pyrometallurgical applications. This paper illustrates the application of numerical optimization techniques in combination with the kiln model in the interrogation of a generic iron-ore reduction process. The fundamental modelling concepts are explained, followed by a description of the optimization approach. The results show how the combination of the two methods, with modern computing power, can generate a large number of viable design and operating candidates.

Jan 1, 2014

By Gordon E. Forward

Sustainable development in the mining and metallurgical industrial sectors can be implemented by two distinct groups: 1. The managers and operators of existing facilities ? working with industrial processes and systems that have been operating for many years, in some cases several decades 2. Those who are engineering and building new facilities or upgrades of existing plants. The focus of this paper is to look at approaches and tools available to bring sustainable development thinking and action to these two distinct areas. The paper will discuss: 1. The concept of working with existing facilities and processes to minimize waste and maximize product from a regional raw material/resource consumption perspective using By-product Synergy. The BPS concept has been carried out in Texas (TXI-Chaparral?s STAR Example), in Calgary, Alberta with Suncor assistance, in Montreal, Quebec with Noranda as project leader and currently in Ontario with Dofasco as industry champion. Successful outcomes are presented. 2. A new approach to designing greenfield facilities or upgrades to existing plants using a sustainable development review process. Undertaking the review early in every project can institutionalize the concept of discussing and implementing waste elimination, design for environment, eco-efficiency, risk minimization and community awareness and involvement in the future capital stock. The review process has been developed as an excellent tool for measuring and reporting on a corporation?s sustainable development progress. Examples of how this approach has been adopted in the mining and metallurgical industry, and the resultant outcomes are given.

May 1, 2002

By Ernest Ph. Hérivel

The mine and treatment plant of the Teziutlan, unit of the Mexican Corporation, S. A., are located at Aire Libre, in the District of Teziutlan, near the northwest edge of the State of Pueblo, Republic of Mexico. The property is leased from the Teziutlan Copper Co. The town of Teziutlan is the terminus of a branch railroad starting from Oriental Junction or the Mexico-Jalapa-Veracruz narrow-gage system of the National Railways of Mexico. A branch line 18 km in length from Teziutlan to Aire Libre belongs to the Teziutlan Copper Co. and is leased and operated in conjunction with the mine.

Jan 1, 1933

By A. Josefsson

The transition temperatures of 0.01 to 0.02 pct carbon steels are shown to be strongly influenced by cooling rate in the a range, quenching from A, causing a very low transition temperature even after strain aging. In a titanium-stabilized steel and in a steel with 0.05 pct C this effect is absent. NORMAL mild structural steels usually show a structure of more or less pure ferrite, as a matrix, in which cementite grains or pearlite are embedded. Of these components, ferrite is by far the most interesting one as far as ductility and brittle (cleavage) fracture are concerned. Obviously, pear-lite and carbide are by no means necessary for a cleavage crack to nucleate and grow in the ferrite, as steels with a very low carbon content (Armco iron with 0.02 pct C) have an impact transition temperature just as high as semikilled steels with 0.26 pct C.1 Although it has been argued that a very embrittling effect is to be expected from cementite, precipitated as continuous films along the ferrite grain boundaries,'. " the micrographic evidence for a direct causal connection between the brittleness and these films does not seem to be very convincing. On the other hand, it has been stated that cementite particles in ferrite are able to stop ferrite cracks.4,5 In any case, the properties of the ferrite itself seem to be of overwhelming importance to the ductility of steels, justifying a thorough study of steels consisting of ferrite of different compositions, but principally free from pearlite, which means a carbon content below 0.02 pct. Such investigations have been carried out using the impact transition temperature as a criterion of the tendency to brittle fracture and have given some rather unexpected results. One result is the profound influence of carbon on the transition temperature of the steel in normalized condition. If the carbon content is reduced from 0.02 to 0.015 pct and below, a nearly discontinuous decrease in transition temperature appears even with high percentages of such elements as phosphorus and nitrogen present. This will be reported elsewhere." The present paper deals with another effect of carbon upon transition

Jan 1, 1955