Search Documents

By R. Pipeleers

Recent experience has shown that all underground workplaces in the Campine Coalfield in Belgium will require controlled cooling within three years. Considering the socio-economic and legal importance of the climatic problems underground, IREA has undertaken studies in forecasting the climate of future workplaces, planning the necessary cooling equipment and optimizing efficiency in the existing cooling equipment. These studies are being carried out using the climate forecasting program of Bergbau-Forschung. So far, the German model has been obliged to utilize manually measured data from a few workplaces in the Campine. As the model does not fit very well with these measurements, it has been thought necessary to' develop a system of continuous data acquisition and transmission. This system is being tested in the Beringen mine of the N.V. Kempense Steenkollenmijnen. In the first part of this paper the digital tranmission system is described; in the second the sensors used to collect the necessary climatic data are presented, and in the third some results are given.

Jan 1, 1987

By Clarence Hall, Spencer P. Howell

Among the more important factors involved in the use of high explosives in blasting operations is the means employed to bring about the detonation of the charge. When flame is applied to high explosives many of them may burn if not confined; but all of them when burning under certain conditions of confinement may detonate. Detonation may also be effected by mechanical means, such as frictional impact caused by a blow or by rubbing between surfaces. By this means, however, the full effect of the explosive charge may not be developed, so that a partial detonation, often accompanied by the burning of the explosive, results. When nitroglycerin was first used it was fired by the application of flame, but considerable difficulty was experienced in exploding it with certainty and in obtaining uniform resl'llts. In 1864 Allred Noble, a Swedish engineer, discovered that nitroglycerin could be surely and completely detonated by exploding in contact with it a small quantity of an initiatory explosive. Mercury fulminate was the substance then found capable of producing the best results There are many other fulminates and other substances that will produce complete detonation of commercial" high" explosives, but detonators or electric detonators containing mercury fulminate as the characteristic ingredient are still almost exclusively used in this country. The term" detonator" is used in the publications of the Bureau of Mines to designate what the miner calls a "blasting cap "-a copper capsule containing a small quantity of some detonating compound that is ignited by a fuse. The term" electric detonator" is applied to a blasting cap that is similar except for being ignited by means of a small wire which is heated to incandescence or fused by the passage of an electric current. One of the conditions prescribed by the Bureau of Mines for a permissible explosive a is that it shall be :fired by a detonator, or preferably an electric detonator, having a charge equivalent to that of the standard detonator used at the Pittsburgh testing station. A further requirement is that this charge shall consist by weight of 90 parts of mercury fulminate and 10 parts of potassium chlorate (or their equivalents). At the request of a manufacturer of permissible explosives, an investigation was undertaken by the bureau to determine the relative strength of detonators and electric detonators having different compositions. The tests of electric detonators herein reported were conducted by H. F. Braddock, junior chemist; J. W. Koster, J. E. Tiffany, junior mining engineers; and A. S. Crossfield, junior explosives chemist, at the Pittsburgh testing station of the bureau. Similar tests of detonators were not conducted because it was believed that the results would not show sufficient variation to warrant such tests. It is hoped that the conclusions drawn from the tests made will be of service to those using explosives by enabling them to select the grade of detonator or electric detonator that will insure the most effective results. The conclusions are given in this bulletin, which is published by the Bureau of Mines as one of a series of publications dealing with the testing of explosives and the precautions that should be taken to increase safety and efficiency in the use of explosives in mining operations. The results of tho experiments described in this bulletin show that the average percentage of failures of explosives to detonate was increased more than 20 per cent when the lower grades of electric detonators were used instead of No. 6 electric detonators, and was increased more than 50 per cent when these lower grades were used instead of No. 8 electric detonators. It is noteworthy, however, that when sensitive explosives, such as 40 per cent strength ammonia dynamite (p. 33), were tested under conditions ideal for detonation, the same energy was developed irrespective of the electric detonator used. When tests were made with a less sensitive explosive, such as a 40 per cent strength ammonia dynamite containing nitrosubstitution compounds (p. 32), the energy developed increased with the grade of the electric detonator used. For example, the average efficiency of four different explosives was increased 10.4 per cent when a No.6 electric detonator was used instead of a No.4 electric detonator, and 14.9 per cent when aN 0.8 electric detonator was used (see tabulation onp.45). The results of the tests emphasize the importance of using explosives in a fresh condition, but as fresh explosives can not always be had in mining work, strong detonators should be used in order to offset any deterioration of explosives from age.

Jan 1, 1913

By R. H. Matjie, J. R. Bunt, A. C. Collins, J. C. van Dyk, C. A. Strydom

South African discard coal fines and K₂CO₃ blends were heated in a laboratory-scale rotary kiln to produce ashes for H₂SO₄ leaching tests. The optimized H₂SO₄ leaching conditions of 6.12 mol.dm³ (M) H₂SO₄, solid to liquid ratios 1:5 and 1:10, and 80°C for 8 hours were used. K₂CO₃ was added to increase the dissolution efficiency of K. The objective was to determine if the Al present in metakaolinite (Al₂O₃.2SiO₂), the Al, K, and Ti in the alumino-silicate glasses, and the Ti in rutile (TiO₂) in the ashes could be selectively dissolved in H₂SO₄. XRF results show that the ashes formed at 700°C dissolved more efficiently (87% Al, 89% K and 23% Ti) compared to the ashes formed at 1050°C. This can be attributed to the presence of Al₂O₃.2SiO₂, K₂CO₃ melt, K₂CO₃ remnants, KAl(SO₄)₂, and K-aluminosilicate glass in these ashes. XRD results indicate that the ashes prepared at 1050°C contained anorthite (CaAl₂Si₂O₈), microcline (KAlSi₃O₈), pseudomullite (Al₂O₃.SiO₂), and silicon spinel (2Al₂O₃.3SiO₂), which are either insoluble or only sparingly soluble in H₂SO₄. These minerals resulted in the lower dissolution efficiencies of Al and K. Based on the high dissolution efficiencies of Al and K for the ashes produced at 700°C, coal fines blended with K₂CO₃ could possibly be utilized as feedstocks for the production of aluminium(III), potassium(I), and titanium(IV) and a sulphate-containing leach liquor. Furthermore, the environmental issues and costs associated with the handling and disposal of large volumes of coal fines will also be resolved.

Aug 2, 2022

By C. F. Jackson

This paper describing the mining practices at a mine in the Southeast Missouri district is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The conditions, operating methods, and practice described in the following pages arc those obtaining at a property in the Southeastern Missouri lead belt, St. Francois County, Mo. This property is the eldest in the county and is a consolidation of a number of separate mines originally opened up as individual operations many years ago. Present-day operations have necessarily to be adapted to suit the older levels, stones, and pillars, and also the recovery of ore from worked over areas which was considered too low grade to mine in the earlier days constitutes a different problem than that of development and mining in virgin ground.

Jan 1, 1929

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By C. Birch

"The purpose of this study was to establish the impact of discount rates on cut-off grades for narrow tabular gold deposits as characterized by the goldfields of the Witwatersrand Basin in South Africa. There are various methods available for determining the cut-off grade, from simple breakeven calculations to sophisticated software packages that consider a variety of inputs to optimize the cut-off grade. For this study a simple financial model was created in Microsoft Excel® that links the ore flow, block listing, and the cash flow. This allows the cut-off grade to be optimized considering how the cost of capital and chosen discount rate affect the cash flow.The discounted cash flow (DCF) and resultant net present value (NPV) are a widely used valuation method for production properties according to the South African Code for the Reporting of Mineral Asset Valuation (SAMVAL Code). The financial model in this study utilizes the Solver function, as well as simple Microsoft Excel spreadsheet formulae to optimize the NPV. Solver was chosen as it is a standard feature in Excel and thus no additional software costs are incurred beyond the basic Microsoft Office suite. For the purpose of this study, just narrow tabular gold deposits of the Witwatersrand Basin were considered. An example of a typical ore block listing, as well as the costing figures, was obtained from an operating gold mine. The results obtained from the study financial model were compared to the current cut-off grades obtained from the mine using their proprietary optimizer program, and were found to be comparable. The methodology utilized for this study thus appears valid.The cut-off grade was optimized considering the cash flow, which includes the variable mineral resource royalty tax, the variable gold income tax, as well as the discount rate. By comparing the resultant NPVs using discount rates of zero, 9%, and 12%, the impact of the discount rate on cut-off grades, resultant life of mine, and average mining grades (AMG) could be compared for the example ore block listing. The South African Code for Reporting of Exploration Results, Mineral Resources and Mineral Reserves (SAMREC Code) does not require operations to state if a discount rate was considered in determining mineable reserves. Mining companies approach the question of applying discount rates in determining their cut-off grades, and thus mine planning strategy, in different ways. Due to the negative impact that optimizing purely on NPV has on the life of mine, some choose to optimize only on profit. Other companies have reverted to utilizing pay limits as their primary grade planning strategy. The calculated cut-off grade is then considered to be another planning indicator rather than a hard determination of mineable reserves."

Jan 1, 2016

By Oliver Bowles

This report covers the character, properties, origin, occurrence, and uses of the traprocks and describes briefly the methods and equipment employed in quarrying and preparing them for market. Production of traprock occupies an important place in industry. In 1960 the output in the form of crushed stone reached nearly 58 million tons valued at $87 million. Traprocks are also shaped into blocks of dimension stone for monuments, building construction and decoration, and specialized products such as surface plates.

Jan 1, 1963

By H. Y. Sohn

Considering the two most important issues the ironmaking industry faces today, i.e., energy consumption and greenhouse gas emissions, it would be advantageous to utilize the concentrate-size raw materials directly without pelletizing or sintering, especially without the use of coke. This plenary lecture describes two such processes developed at the University of Utah. One is the Flash Ironmaking Technology (FIT) and the other is a moving-bed process for continuous ironmaking with gaseous reduction of iron ore concentrate (MBIT). These technologies are designed to produce iron directly from iron concentrate without requiring pelletization/sintering and cokemaking in two significantly different temperature ranges. They take advantage of the high reactivity of the concentrate particles and will considerably reduce energy consumption and carbon dioxide emissions compared with the current processes. The process of the development from the conception of the idea, to kinetic feasibility establishment, to laboratory flash furnace, and finally to the operation of a prototype facility for the development of the FIT is discussed. The development of the MBIT also started with the formulation of the process concept, followed by kinetics feasibility establishment, and the design of a potential industrial reactor. The results of economic analyses on the FIT are briefly described.

May 12, 2023

By Kristin K. Mueller, Lucie Coudert, Thi Yen Chau Nguyen, Lan Huong Tran, Jean‑François Blais, Guy Mercier

Fluorite (calcium fluoride—CaF2), also known as fluorspar, is an industrial mineral used in metallurgy, hydrofluoric acid production, and ceramics manufacturing. Based on the results from a previous study, a low-grade fluorspar by-product (20.0% CaF2) originating from the exploitation of a rare earth carbonatite deposit can be improved to 75.4% by combining magnetic separation and acid leaching. The present research aimed to develop and optimize a column flotation process to increase the purity of this fluorspar by-product by removing residual silicate minerals and meeting the requirements for ceramic manufacturing (> 85% CaF2). The optimal flotation conditions required for maximizing the recovery and improving the grade of a fluorspar by-product were identified using a conventional approach combined with a response surface methodology (Box-Behnken design). Optimal fluorspar flotation was achieved under the following conditions: 3.6 g/kg of sodium oleate as the collector, 2 g/kg of sodium silicate as the pH modifier and depressant, a conditioning time of 35 min, a flotation time of 7 min, and a solid-to-liquid ratio (S/L) of the pulp of 5%. Under these conditions, 86.8% fluorspar recovery was achieved, and the grade increased from 76.5% in the feed (metallurgical grade) to 88.6% (ceramic grade) in the final concentrate. The silicon content decreased from 5.66% in the feed to 1.12% in the fluorspar concentrate. Using magnetic separation before the flotation improves the final content of fluorspar in the concentrate with the final grade of 94.4%.

Sep 9, 2022

By K. H. Singh, J. N. Szuck, J. A. Riddell

"Hydraulic rock drilling equipment has been in use at Falconbridge over the past two years in both production and development situations. This paper deals with the experience gained in the application of hydraulic drilling in the company's mines and discusses the benefits and problems encountered during their use. The paper primarily focuses on technical, operating, maintenance and economic aspects of the machines, and does not attempt to compare the performances of different machines from the various manufacturers.IntroductionThe Sudbury Operations of Falconbridge Nickel Mines Limited are comprised of five operating mines and two mines under development. All the production comes from underground mines, mostly at depths below 1000 metres. The company, faced with increases in operating costs and difficult mining conditions, has continued to seek solutions with the help of new mining technology.The development of electric-hydraulic drilling machines in Europe had been pursued with great interest and, in 1979, a decision was made to test these machines to prove their technical and economic viability under operating conditions. Since then, a number of electric-hydraulic machines have been evaluated in different situations and currently nine hydraulic machines are being used in the company's various mines. These machines are comprised of two-boom drilling jumbos for development, one-boom machines for longhole drilling and a large-hole-diameter drilling rig for blasthole drilling. One hydraulic jumbo has also been used in a cut-and-fill stope."

Jan 1, 1982

By H. M. Chance

The iron-ore deposits of the Hartville district are located near the new town of Guernsey, about 100 miles north of Cheyenne. The writer has been familiar with them since 1887, having visited the district several times for different clients— his last examination having been made in November and December, 1897. The deposits extend in a general N.E.-S.W. direction from a point in Section 33, Range 65 W., Township 28 N., on the west side of Whalen cañon, through Sections 4, 5, 6, 7 and 8 of Township 27 N. in the same Range, and over into Sections 1 and 12 of Township 27 N., Range 66 W. General Characteristics. The ore is a remarkably pure red hematite, extremely low in phosphorus, and carrying a small percentage of silica, as shown by analyses given below, and similar in many respects

Jan 1, 1901

By P. Harvey

"Following initial discovery in 1991, BHP Billiton Diamonds Inc. opened Canada’s first diamond mine, the EKATI Diamond Mine (EKATI) in the Northwest Territories on October 14, 1998. Four short years later, on November 29, 2002, saw the opening of North America’s first underground diamond mine, the Koala North mine. Nestled between the original Panda open pit and the new Koala pit, which is in the early stages of production, Koala North represents the only underground kimberlite mining venture in Arctic conditions outside the new underground mines being developed by ALROSA in the Yakutsk region of eastern Russia. Extensive underground kimberlite mining has been practiced in the Republic of South Africa for much of the 20th century and continues today.Underground mining represents a key component of the long-term business plan for EKATI. As various open pits reach their economic limit, continued recovery of high-value ore at depth is dependent upon the ability to productively mine the kimberlite pipes by underground methods. As a function of its location, size, and value, the Koala North pipe is ideally positioned to host the first underground mine at EKATI. Koala North is designed and approved as a learning mine, from which to gain valuable experience in preparation for the potential mining of other larger, higher value pipes by underground methods in the development, the Koala North mine is well into its production ramp-up phase and currently producing at around 1,200 t/day from the first two production levels."

Jan 1, 2005

By Walter Voglauer, Elisabeth Zechmeister

Five serial photos show the first second of the demolition of a 75 m high, reinforced concrete tower in the 23rd District of Vienna, Austria. The tower demolition with high explosives was necessary because a 175t excavator could not finalize the destruction with mechanical tools. All mechanical works in preparation of the blast, such as the borehole drilling, were done by civil companies under the responsibility of the contracted demolition company PRAJO. The blasting itself was planned and executed by the engineer corps of the Austrian Armed Forces, Sunday, May 26, 2013. Nearly 800 boreholes filled with more than 100 kg of military plastic explosives were initiated with about 1,600 Austin electric delay detonators in exactly 1,000 ms and 30 steps of delay. The 10,000 tons of reinforced concrete tower fell as planned without any damage to the environment. Photo 5. The rest of the detonators initiate the water pools filled with high explosives forming a bizarre white water front to fight the following strong development of dust. The first 1,000 milliseconds are over.

Jan 1, 2015

By S. Dubnewych, S. Kieffer, M. T. McRae, R. R. Redd

The seismic vulnerability of the existing outlet tower at Lake Mathews reservoir, located in Riverside County, California, necessitated the design of a new outlet facility to assure serviceability of the facility following a major earthquake. The components of the proposed facility include: a new outlet tower; a shaft; a new outlet tunnel; an approach channel that will be excavated underwater; and two short tunnels that will connect the new outlet tunnel to the existing outlet tunnel via the shaft. As the new facilities will be constructed while the reservoir is in operation, a cofferdam will be constructed around the site of the new outlet tower. The design for the underground facilities used a combination of empirical methods; limit equilibrium analyses, including displacement-based pseudo-static analyses for dynamic loading conditions; and numerical analyses. This paper outlines the design methodology used to develop an innovative design for the facilities which can be constructed within the time frame required by the operational schedule of the reservoir and existing outlet facility.

Jan 1, 1999

By Frederick W. Horton

The lack of comparable and accurate statistics of coal-mine accidents in the United States as a whole led the Bureau of Mines in 1911 to undertake the collection of such data. The importance of such statistics as a basis for remedial legislation can not be overestimated, moreover they serve to indicate the results of the efforts made by the Federal Government, State mining departments, and mine operators throughout the country to lessen the hazard of coal mining. The mining departments of the leading foreign coal-producing countries have long taken cognizance of the importance of such statistics. In Great Britain, official statistics of coal-mine accidents have been collected and published since 1851, in France since 1853, in Austria since 1875, in Germany since 1852, and in Belgium since 1831. The United States not only leads these countries in the production of coal but the output of its coal mines is greater than those of Great Britain, France, Belgium, Austria, India, Japan, and New South Wales combined. Accordingly, it is proper that there should be some official record of the accidents in this, the greatest mining industry not only in the United States but in the world. It is especially appropriate that this work should have been undertaken by the Bureau of Mines, as, through its investigations of mine accidents in the field, it is constantly in close touch with coalmining conditions throughout the country. Its engineers are not only able to obtain first-hand information as to a great many accidents, but, through their special training and experience, are able to appreciate the significance of the figures reported by the coal-mine operators, thus aiding an intelligent and uniform classification 01 the accidents for the country as a whole. Further, the State mining dnpartments and State mine inspectors of every State in the country having a system of coal-mine inspection are cooperating with the bureau by sending it monthly reports of accidents in the coal mines of their respective States. The receipt of such reports places the bureau in a most advantageous position to publish promptly statistics of these accidents. Although a few years ago accurate statistics of c~al-mine accidents in the United States as a whole were entirely lacking this bureau was able to pubjiish the 1912 statistics within three n:onths after the close of the year and long before corresponding statistics had been issued by the mining departments of the leading foreign coal-producing countries. The cooperative agreement with the State coal-mine inspectors has not only made possible the prompt publication of the statistics, but it has also enabled the bureau to classify the fatalities by months and according to cause, showing the months in which the greatest and the least number of men were killed and from what causessomething that has never before been accomplished for this country.

Jan 1, 1913

This one day field trip is sponsored by the Denver Region Exploration Geologists? Society, May 14th 2009. The trip highlights major geologic features and some notable uranium occurrences along the north-south mountain-basin boundary southwest of Denver and continuing north to Fort Collins, Colorado. Uranium deposits visited include sandstone?hosted roll front type and polymetallic veins hosted in metamorphic rocks. A replacement ?episyenite? type occurrence is considered via description and hand samples but is not visited owing to logistical constraints. Recovery methods addressed include underground mining and in-situ leach recovery. Samples of Precambrian basement rocks, deposit host rocks, uranium ore samples, and ore polished sections viewed by reflected light microscopy will be available. A road map showing the locations of the stops serves as the front cover of this field guide. The Robinson episyenite-hosted occurrence (not visited) is labeled as Stop 6. A stratigraphic column is provided which shows the position of the host rocks at each stop (Figure 1-1).

Jan 1, 2009

By Louis M. Schlesinger, Michael J. Garska, Joel F. Hutwelker, James T. Jr. Tanner

A pilot plant was constructed and operated to investigate the column flotation of 20 x 200 mesh North Carolina phosphate ore, using high throughput, high solids operating conditions developed at the NCSU Minerals Research Laboratory. Flotation was performed at 45% solids in a 9.5 cm (3.75 in.) diameter by 2.26 m (7.4 ft.) tall column at throughputs of 19.1 t/hr/m2 (2.0 stph/ft2) and 31.7 t/hr/m2 (3.3 stph/ft2). Recoveries in excess of 98% of the phosphate value were obtained at the lower throughput -- while obtaining concentrate grades containing over 28% P205 (61.2% BPL) at that recovery. Recoveries of about 95% of the phosphate value were obtained at the higher throughput, while making a concentrate averaging 27.6% P205 (60.3% BPL). In addition, a better understanding of the variables governing the column flotation of coarse nonmetallic minerals was gained. Variables examined included superficial air velocity, throughput (superficial feed velocity), frother type, frother dosage, and bias rate.

Jan 1, 1993

By R. B. G. Yeo

Pronounced isothermal martensite formation at room temperature was measured dilatometrically in a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pctAl, 2.58 pct Ti and 0.25 pct Cb. It is shown that martensite will form isothermally if stabilization of the austenite-martensite transformation is eliminated by removal of carbon. The decarburization of two iron-nickel alloys allows isothermal transformation to martensite to occur at temperatures above their athermal Ms temperatures. In an Fe-22.4 pct Ni alloy, at the 0.008 pct C level, the Ms temperature during air cooling is 85°F higher than that during- water quenching-. At the 0.15 pct C level this difference is reduced to only 5°F. The introduction of carbon causes stabilization during air cooling which lowers the Ms temperature virtually to the same level as determined during mate?. quenching. Thus in the 0.15 pct C alloy, the Ms temperature is almost independent of cooling rate. It is suggested that rival theories of martensite formation should be reexamined in alloys of sufficiently low carbon and nitrogen content to eliminate the complication of stabilization. The Ms temperature of a steel containing 0.01 pct C, 24.9 pct Ni, 0.26 pct Al, 1.58 pct Ti and 0.15 pct Cb, solution treated at 1500°F and air cooled as 1/8-in. diam specimens, was found to be 57 °F. 1 However, when held for several hours at room temperature the steel hardened slightly and became appreciably ferromagnetic. Isothermal transformation to martensite was first revealed by Kurdjumov and Maksimova2 in an iron-base alloy containing 0.6 pct C, 6.0 pct Mn and 2 pct Cu. Most of the other studies of isothermal martensite have also been confined to highly alloyed steels which transform at subzero temperatures; for instance, DasGupta and Lement, 3 Cech and Hollomon, 4 Machlin and Cohen,5 Shih, Averbach, and Cohen.6 Averbach and cohen7 noted a rapidly decaying volume increase at room temperature in a steel containing 1 pct C, 1.5 pct Cr and 0.2 pct V. cina8 and Marshall, Perry, and Harpster9 have described the isothermal transformation to martensite at room and subzero temperature in stainless steels. Kurdjumov10 has recently reviewed the subject, noting that the isothermal formation of martensite can be observed only in the temperature range somewhat below Ms or below -50°C. The isothermal formation of martensite may be characterized as follows: 1) It occurs in steels of widely different compositions, the main prerequisite being a low transformation temperature. 2) The transformation occurs by the formation of new plates and not by the growth of old ones. 3) The isothermal transformation is suppresed by stabilization during slow cooling or holding at temperatures near room temperature. However, the factors governing this mode of transformation are still not fully understood. The formation of martensite isothermally suggests an activated process. The early theories of martensite formation did, in fact, utilize classical nucleation concepts. Kurdjumov 11 first proposed the presence of thermally activated nuclei of different sizes and compositions which would grow if they reached critical size during cooling. This treatment was enlarged and developed quantitatively by Fisher, Holloman, and Turnbull12,13 and was later reviewed by the latter two authors.14 Fisher15 associates Ms with a nucleation rate of one per cc per sec. At slightly higher temperatures the nucleation rate is so low that isothermal formation of martensite is not observed in reasonable times. At slightly lower temperatures the nucleation rate is so high that it could not be suppressed by rapid cooling. By judicious use of parameters Fisher 16 was able to obtain good agreement between classical nucleation theory and the incubation times of martensite formation.4 However the application of these principles to martensite formation in iron-nickel alloys15 predicts that an alloy containing about 30 pct (31 at. pet) Ni would not transform. The presence of an Ms temperature at -223° C in an alloy containing 34.1 pct (33 at. pct) Ni led Kaufman and cohen17 to reject the hypothesis of homogeneous nucleation in favor of the reaction path theory originally proposed by Cohen, Machlin and Paranjpe.18 This theory conveniently explains the formation of martensite athermally but becomes labored when dealing with isothermal formation. Kaufman and cohen19 did explain the isothermal activation of embryos by assuming it to be a result of the expansion of their boundary dislocation loops but this treatment predicts an upper temperature limit of isothermal martensite formation.

Jan 1, 1962

By J. Weyer

"Colored gemstones are most often mined in small scale artisanal mining operations. Sri Lanka is well known as source for precious stones since thousands of years. Gemstones are mine in small open pits, directly in rivers (river dredging) and in underground mines. Almost all mined deposits are alluvial deposits. PRECIOUS STONES AND DEPOSITS Precious stones from Sri Lanka are well known for thousands of years. Tales and legends from Arabia, India, China and reports from discoverers like Marco Polo describe the fabulous stones from Ceylon which was the name for Sri Lanka before 1972. Already 1000 BC King Salomon got valuable gemstones from the legendary Queen of Sheba on her visit to Jerusalem. Paintings (frescoes) of the “cloud maidens” with huge gemstones can be seen at the “mirror walls” of the Sigiriya rock fortress - one of the eight World Heritages Sites of Sri Lanka.And even today some of the most valuable and most desired gemstones come from Sri Lanka. The term “Ceylon Sapphire” stands for an excellent royal blue color of high quality corundum from Sri Lanka. Reason enough to look a bit closer how these gemstones are mined. Sri Lanka has rich gemstone deposits which are mined underground, in small open pits or directly within a river. Some of the primary deposits in magmatic and metamorphic rock are also known, but most gemstones are mined in secondary alluvial deposits. Gem bearing deposits can be found in a band from NW to SE. Highly probable deposits and main mining areas can be found around Ratnapura – the city of gems, down to the coast (Matale) and up to the region around Elahera. These secondary deposits are mostly thin layers of gravel and sand, so called “illam”. The depth can vary between some dm to 10 25 m or even almost 40 m. But the average depth is about 12 m. Gemstone mining is controlled, licensed and regulated by a special authority – the National Gem and Jewelry Authority - which was founded in 1993. Another task of this authority is the promotion and development of the gemstone industry and the control of import and export of gemstones. Any violence of the NGJA law can lead to a fine or even up to 5 years imprisonment. To increase the confidence in the gemstone industry the Authority offers a unique service to foreigners. All bought gemstones can be tested free of charge in certain laboratories in Ratnapura and Colombo. So visitors can be sure they got no imitations, wrong stones or even synthetic stones or glass. It was said that detected synthetic stones will be destroyed and the seller will do all he can to replace the stone with the right stone. Otherwise he will lose his license."

Jan 1, 2016

By E. A. Devuyst

Metallurgical processes involving the use of cyanide such as gold cyanidation, metal plating and flotation, generate effluents containing cyanide and cyanide in complex combinations with heavy metals in quantities exceeding those regarded as being safe for discharge into streams. A new process for destruction of free and complexed cyanide and related-species in wastewaters has been developed at the Inco research laboratories using sulfur dioxide, air and lime. High reaction rates are obtained in the presence of a small amount of copper which acts as a catalyst. Cyanide species can be reduced to as low as 0.1 mg/L in a very short treatment time. Examples of treatment of gold mill effluents and barren slurries, plating rinse waters and flotation liquors or tailing slurries are given.

Jan 1, 1982