Search Documents

By Antonio Favia, Carsten Sowa, Spencer Diehl, Maria Carolina Campos, Christian Green, Marco Tulio, Olaf Schulz

Casting fluxes are one of the key factors to guarantee a good performance of the continuous casting process. Fluxes are added over the liquid steel in the mold, where carbon in the flux reacts with any air present, to form a reducing atmosphere of CO (g) to protect molten steel from oxidation. Then the oxide components form the sintered layer and they melt to form a liquid flux pool. Liquid slag from the pool infiltrates into the mold/strand channel and lubricates the newly-formed, steel shell. It was very common in the past that the addition of casting flux in the mold was made manually by the continuous casting strand operator, where the addition uniformity would mainly depend on the attention of the Operator in process and the addition standard would change from one operator to another, may causing variability on the continuous casting quality parameters. This paper presents improvement of continuous casting parameters such as, stability of flux thickness and reduction of dust in the continuous casting process, with the use of flux distribution mechanism in two continuous casting machines from two different steel plants.

Oct 1, 2019

By Gang Guo, Zhong Liu

"In response to an increasing demand of anchored structures for underground space and transportation infrastructure in China, an innovative underreamed ground anchorage system was created. The novel anchorage system has provided more efficient functions with higher capacity at lower cost, because of the enlarged cylindrical body (known as ECB) sealed in capsule at bottom of anchorage. This paper presents the detailed structure of innovative anchorage system and its special features. To investigate the bearing mechanism of new anchorage, we evaluate its performance and failure mode based on the experimental results, and also indicate its strain-hardening load-displacement relationship. Unlike the shaft anchorages, it is identified no overall failure to be found in soil surrounding the underreamed anchorage. More importantly, the anchorage capacity is governed by the base resistance, which takes more than 80% of total pullout capacity resulting from the contribution of ECB. Finally a case history of anti-floating project introduces the new combined construction approach and procedure, which has provided the contribution to the quality control and cost efficiency.INTRODUCTION AND BACKGROUNDThe construction boom over two decades in China has resulted in an increasing demand for underground space and slope stability. The infrastructures market requires the more efficient anchorage systems for retaining structures, resisting uplift forces and slope protection. The major concern focuses on gaining higher capacity and lower cost resulted from perfecting anchorage systems. There are three main anchorage systems designed to achieve the above objectives: ? single bore multiple anchorage system (Barley 1997), ? regroutable anchorage system (Smoltczyk 1991), ? underreamed anchorage systems (Xanthakos 1991). Generally, the concept ? comparing with the other two, can be more competitive due to its distinct advantages. To improve the performance and durability of ground anchorages under the complex geological conditions and diversified engineering requirements, a number of different underreamed anchorage technologies had been used, which included cone - shape anchorage described by Liao, Wu and Shu (1997) in Taiwan, Soilex anchorage developed in Sweden (Massarsch et al. 1997), Soletanche anchorage proposed in France, blasting anchorage used in Czechoslovakia (Hobst and Zajic 1986), jet-grouting anchorage innovated in Europe (Anon 1988), as well as deep mixing anchorage created in Japan (Cheng et al. 2000).The underreamed anchorage systems have the remarkable advantages compared to the shaft anchorage system. However, there are also some weaknesses inherent in the underreamed systems. For instance, the mechanical underreamed anchorage is unsuitable in sand or waterbearing ground, because the enlarged hole is easy to collapse, and it is hard to ensure the quality of anchorages. On the other hand, relying on the blasting in deep hole, the geometrical space and dimension of enlarged hole is uncontrollable, meanwhile, the continuous blasting operations may easily cause the serious ground deformation and the negative effects to the completed anchorages."

Jan 1, 1900

By Donald H. McLaughlin, John H. Moses

IN the latitude of Lima, the broad uplifted block that forms the Andes is made up of a complex sequence of folded and faulted sediments and volcanics, broken by large and small bodies of granitic rocks and porphyries with which the principal mineral deposits are closely associated in both time and space. The intrusives are a final episode in the geologic history as revealed by the consolidated rocks, for after their emplacement and after the formation of the primary ore deposits in and about them the record is simply one of long continued erosion and uplift.

Jan 1, 1945

By J. A. Botín

Investment decision for large mining projects imply an enormous financial risk and therefore, require a more complex risk evaluation methodology taking into account all sources of uncertainty from each process in the project value chain. Generally, the main sources of risk are those related to uncertainty on grade and other techical variables of the orebody. In this study, conditional simulation is applied to develop a risk management model to quantify and to manage financial risk associated to uncertainty on the grade of the orebody. The model was validated in case study on a real porphyry copper orebody in Chile.

Feb 23, 2014

"In response to mine head grades declining and orebodies becoming more complex, Glencore Technology has developed an alternative method for recovering economic minerals once leached into solution, rather than relying on conventional flowsheet options. The method involves the precipitation and separation of base metals from solution with limestone or lime. The final grade of these precipitate is not usually high enough to attract favourable terms of sale due to dilution from gypsum and sulphate salts. A set of operating conditions have been developed to allow the separation of the base metal precipitate from gypsum by exploiting the difference in particle size. A high-grade oxide product can be easily separated from the gypsum stream at very low cost. This process was originally developed by Glencore for zinc and copper systems. This paper reports on the successful application to nickel and cobalt, and this process has significant advantages over the incumbent precipitation process utilising magnesia.INTRODUCTION During evaluation of transitional and oxide zinc ore deposits during the 1990’s, Noranda Inc. (now Glencore) developed a sulphate based ore leach process to extract zinc into solution. For flowsheet development, conventional schemes dictated that once the zinc was dissolved in an acidified solution it was recovered by means of purification or solvent extraction followed by electrowinning and casting to produce zinc ingots. The deposits Noranda evaluated were high grade but had a relatively short mine life (10 years) and economic analysis showed that the projects couldn’t sustain the investment of a full zinc refinery. Compounding this problem was the lack of power supply infrastructure and the high power cost in the region. Noranda then evaluated alternative means of recovering zinc from solution. Laboratory testwork showed that a high-grade zinc precipitate (+50 wt% Zn) could be produced as an oxide, carbonate or sulphide by contacting acidified zinc sulphate solution with a number of reagents including soda ash, sodium hydroxide, and sodium hydrogen sulphide. Economic evaluation showed that the cost of the reagents are prohibitive, especially when the final product is still a metal intermediate (ZnO, ZnCO3 or ZnS). Noranda then continued to focus on fine zinc oxide precipitation for supply into the automotive tyre industry as this product would attract favourable terms of sale as a premium on Special High Grade (SHG) zinc."

Jan 1, 2017

By S. R. Zimmerley

Recent investigations of finely ground materials have verified Rittinger's law of crushing.4, This law states that the surface produced is proportional to the work expended in the crushing operation. Thus, for a unit of work applied to crushing quartz a definite amount of surface will be produced. Obviously, this amount of work applied to some other mineral will not produce equivalent surface. It follows that in an investigation of mill practice, where ore is being crashed, the relative crushing resistance of the component minerals must be known. In a previous investigation of the Rittinger law,5 the crashing resistance that is, the work required to produce a unit of surface - was accurately determined for quartz. The surface values were obtained by means of the rite of dissolution of quartz in hydrofluoric acid.6 If it were possible so to measure surface on other minerals the determination of relative crushing, resistance would be a simple matter; however, the results obtained on minerals other than quartz by a dissolution method were not encouraging. Moreover, if accurate values could be obtained by dissolution this method could probably never be used on a mixture of minerals such as occurs in an ore.

Jan 1, 1929

By Hidefusa Takahara, Koichi Miyake, Dierk Raabe

"Mechanical properties of copper wires were examined. The copper wires containing 5-10 mass % chromium and 1-3 mass % silver were produced through heavily cold deformation. It was expected that the copper wire was easily fractured during cold deformation because of the existence of brittle chromium phase in the alloy. In fact, the copper wire was fractured due to large work hardening, when the true strain [n] exceeded 5. However, the copper wire annealed at 1273K for 6 ks ·in the middle of deformation process could be smoothly drawn to 11=8. After precipitation treatment for silver phase at 473k for 1.8 ks, the wire was able to further drawn to n=8.4. The final deformed wire showed tensile strength higher than 1200MPa.IntroductionDownsizing of electronic devices has led to the demand of finer and higher strength materials for cables. Conventional copper alloys have about 800MPa in ultimate tensile strength. These strength are mainly obtained by precipitation hardening. Nowadays, a process for higher strength wire has been developed, where dual phase copper alloy is used. When it is drawn heavily, the' second phase is elongated along drawing direction and the wire gets high strength due to fiber reinforcement (1). That alloy is so called in-situ formed fiber reinforced ·alloy. Cu-Ag(2), Cu-Nb(3) and Cu-Cr(4) systems are well known as such alloys. It is also well known that chromium is brittle material except single crystal and high purity of chromium. However, Mihara et al. C5l have achieved 1 GPa in ultimate tensile strength in the Cu-Cr-Zr and Cu-Cr-Ti alloys by appropriate thermo-mechanical processing.In this study, the Cu-Cr-Ag systems were investigated: The alloys contained 10 or 5% chromium and 3 or 1 % silver. It was demonstrated that silver precipitated in copper matrix contributed on further hardening."

Jan 1, 2000

By Edwin R. (Original by) Phelps

Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal were mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-year periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu yd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu yd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining; 4) Surface mining normally recovers a- much higher percentage of the coal reserve than can be recovered by underground mining. 5) Some coal measures can best be extracted by surface mining [ ] methods because of geologic reasons such as the nature of the roof or bottom, thickness of the seam, multiple bedding, etc.

Jan 1, 1981

By D. Harrington

Ventilation of underground workings consists in establishment of such control of air currents that the underground workers may work in safety, with maximum comfort and efficiency, and without impairment of health; and requires that the mine openings may be made subject to such control of air flow as to remove from these workings at ordinary times harmful gases and dusts, and that, at time of emergency, such as fire or explosion, there may be maintained as much or as little air flow as may be desired covering portions of the mine or the mine in its entirety. Control of air flow is the keystone of any ventilating structure, and this very essential feature is obtainable only by the installation of mechanically-operated fans, together with other;. ventilating devices such as doors, over-casts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. While much has been written about natural ventilation and many claims made that in specific mines there is sufficient natural air flow, there are few if any mines, coal or metal, where natural ventilation supplies anything like adequately safe or healthful conditions for underground workers even at ordinary times; and at a time of mine fire or explosion, mines depending upon natural ventilation are practically helpless, and certainly are decidedly dangerous to those unfortunates forced to be in them. While ventilation has practically always been deemed an integral part of coal mining, metal mines have rarely paid much, if any, attention to air circulation until forced to do so by occurrence of some untoward condition or accident. Yet metal mines actually have as great need of efficient circulation of air as have coal mines. The coal mine must remove the dangerous explosive gas, methane, also fumes from explosives and, in occasional places, other gases such as carbon dioxide or nitrogen.

Jan 1, 1933

By C. Kathryn Sole

The close proximity of cobalt and nickel on the Periodic Table and their frequent occurrence together in nature means that their separation in primary hydrometallurgical flowsheets is not only often necessary, but requires the use of innovative chemistry to achieve high selectivity. Today, increasingly stringent demands for the high-purity cobalt and nickel salts required for battery applications in consumer electronics, electric vehicles, and solar applications are again challenging the state of the art. The evolution of cobalt–nickel separations is traced from the basic precipitation technologies employed in 1960s, through commissioning of the first cobalt solvent-extraction plant in South Africa in 1974, to the commercialisation of organophosphinic-acid extractants (which provided a step-change improvement in selectivity) and their eventual widespread use in the 1980s and ’90s. This was followed later by their sulphur analogue, which enabled different possibilities for laterite processing in the new millennium. Separations in chloride media, which take advantage of the different speciation chemistries, and nickel extraction by oximes in ammoniacal systems are also discussed. More recently, chelating and solvent-impregnated resins have added further dimensions to the possibilities for flowsheet design and enabled higher purity products to be attained from both primary and secondary sources. Selected case studies and flowsheets are described.

By Pingchao Ke

A crystalline polyferric sulfate (PFS) adsorbent was synthesized by oxidizing and precipitating ferrous ions under atmospheric conditions. The morphology, structure, composition and specific surface area (SSA) and adsorptive efficacy to As (III) of the adsorbent were characterized by SEM/EDS and TEM images, XRD patterns, FT-IR spectra, BET SSA analyses and adsorption experiments. The adsorbent presents as morphology of near-spherical aggregate and good crystallinity. A small amount of goethite co-precipitated with PFS in the case of the initial ferrous concentration of 1 mol/L and increased the SSA of the aggregates. The absorbent with co-precipitation of goethite showed good adsorption to As(III) and good filtering performance in the high As(III)-content solution of 10–100 mg/L under acidic, neutral and alkaline conditions (pH 2.09–9.01), and its maximal adsorption capacity and adsorption efficiency were 7911 μg/g and 96% separately. After Adsorption, the stability of the absorbents adsorbing As(III) were evaluated by TCLP tests, and the results indicated that the absorbents adsorbing As(III) were extremely stable, and the concentration of arsenic in all leaching solutions were less than 0.01 mg/L.

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By N J. Beukes, S T. Netshio, M O. de Kock

The Thabazimbi iron ore deposit comprises a series of stratabound orebodies, on average 18 - 25 m thick that are aligned along the faulted basal contact between the Penge Iron Formation and dolostones of the Malmani Subgroup, Transvaal Supergroup. Field geological relationships and petrographic observations suggest that the formation of high-grade iron ores took place after contact metamorphism related to the intrusion of the Bushveld Complex (2.06 Ga) but before the deposition of red beds of the Waterberg Group at ca 1.9 Ga. Hard, high-grade iron ores are predominantly composed of martite and microplaty hematite. Goethite is restricted to supergene-modified ores close to the Late Cretaceous û Early Cenozoic Old African land surface. At depth, the high-grade hematite ores interfinger with low-grade dolomite-hematite and calcite-hematite ores. Iron oxides (martite, microplaty hematite) present in these low-grade ores are texturally indistinguishable from those in the associated high-grade ores, ie ore formation is genetically associated with carbonate metasomatism. Microthermometric studies of fluid inclusions in sparitic carbonates and rare megaquartz reveal their hydrothermal origin. Two compositionally distinct aqueous fluids of shallow crustal origin are identified, namely a Ca-Na-rich high-salinity brine (26 wt per cent NaClequivalent, TH ~160¦C), and an aqueous Mg-K-bearing fluid of intermediate salinity (8.3 - 12.6 wt per cent NaClequivalent, TH~120 - 150¦C). The results confirm that high-grade hematite orebodies at the Thabazimbi deposit owe their origin to an event of extensive oxidative carbonate metasomatism (calcification), similar to that recognised at other important high-grade iron ore deposits in the world. Hydrothermal ore formation is both structurally and lithologically controlled. Size and quality of the orebodies was improved by Late Mesozoic-Cenozoic deep lateritic weathering as carbonate-hematite ores were enriched to friable high-grade ores, but this supergene modification is second in importance compared to the primary event of hydrothermal ore formation.

Jan 1, 2005

By Cale J. Dubois

At Cameco Corporations' Cigar Lake Project, large excavations are developed on the 480 Level and 500 Level must remain stable for at least 15 years to host underground processing infrastructure. Following the successful dewatering of the mine in October 2009, subsequent internal rockmechanics investigations augmented by third party technical investigations; determined that to keep the back of the Water Flush Crusher/Run-of-Mine (WFC/ROMs) excavation stable; required a rehabilitation strategy to mitigate deterioration/deformation of the WFC walls and intersection pillars. The mechanism of failure propagating the movement of the excavation walls is understood to be controlled by the presence of a dominant E-W striking and steeply dipping foliation within a relatively weak and mildly altered rockmass sub-parallel in strike with 14 meters high walls and an intersection span approaching 15 meters. The application of open and resourceful communications between site mining engineers, geologists, contract mining staff, construction management experts, corporate mining and civil engineers, and third party technical experts resulted in a multi-faceted short-term ground support strategy consisting of standard bolting and screening, deep-seated modified-strand cable bolts coupled with heavy gauge mesh straps, rockmass reconditioning using low-pressure grout injection, and horizontal cable-lacing for the intersection pillars applied in lifts using a top-down methodology. The intention of the short-term strategy was to stabilize the excavation so that a long-term structural steel support installation - consisting of composite concrete walls, and arch support applied to the side walls and crown of the back - could be constructed safely. This paper summarizes the evolution of the short and long-term ground support strategy and criteria for the WFC/ROMs excavation developed using elements of civil, mining and hydrogeologic design.

Nov 1, 2011

By J. M. King

A crucial step in the acquisition by one company of the assets of another, the acquisition of the stock of another company, or the merger of two com-ponies, is the legal due diligence which needs to be performed in order for the acquirer to ascertain or confirm the obligations, liabilities and exposures to risk that are being assumed along with the assets or corporate stock being acquired. Where the obligations, liabilities, or exposures to risk arise from existing contracts, or from pending lawsuits, administrative proceedings, or threats of these actions, those matters are relatively straightforward to discover by careful review of the files of the party whose assets or stock is being acquired. However, where a company is engaged in ongoing mining or processing operations and has operated or owned mining proper-. ties, there are many sources of liability and exposure to risk which could have major adverse economic consequences to the acquiring party and which are not revealed, or at least are not clearly delineated, by the records of the company whose stock or assets are being acquired.

Jan 1, 1990

By D. C. Carter

"The Nova Scotia Department of Mines and Energy located a drillhole at Riverside Corner, Hants County, Nova Scotia, to examine the stratigraphy, structure and potash potential of the Kennetcook River gravity low. This evaporite-related gravity anomaly is one of the largest virtually unexplored gravity anomalies in Nova Scotia. The drillhole intersected a structurally complex sequence o flower Windsor Group ('B' Subzone) evaporites. Downhole geophysical wireline logs were used, in conjunction with detailed lithological descriptions, to interpret the structure and stratigraphy of the sequence. Similar application of total gamma ray, density, caliper and neutron-neutron log responses allows stratigraphic correlation of Windsor Group carbonate marker units separated by up to 35 km in Cape Breton. This work confirms the value of downhole geophysical logs as a tool in the exploration of evaporite deposits regardless of the presence or absence of high quality core. INTRODUCTIONThe exploration methodology for evaporite (specifically salt/potash) deposits in eastern Canada (and worldwide) is relatively simple: identify a negative gravity anomaly within a favourable geological setting, Windsor/Cordroy Group sediments in eastern Canada, and drill it (Anderle, 1980). Although this is an obvious oversimplification of the necessary expertise in the planning and complet ion of an exploration program, those familiar with potash exploration drilling can attest to the risks and expense, in terms of time and problems , associated with the location and drilling of diamond-drill wildcat holes. Potash exploration programs in eastern Canada, their results and inherent difficulties, have been documented by Anderle et al. (1979), Cooper (1981), Dekker (1982), Carter and Boehner (1986), Carter (1988) and Carter and Anderle (in prep .).Downhole geophysical wireline logs have become an important tool in the stratigraphic and structural interpretation of evaporite sequences in eastern Canada and, in many cases, represent the only information recovered or the only information available due to the drilling method (rotary) and/or the long term instability of evaporite cores. This paper documents examples of downhole geophysical log responses which, combined with detailed lithological examination of drill core, or in the absence of core, are used in the interpretation of the complex lithology and structure of a deformed evaporite deposit. Geological and geophysical data from the Nova Scotia Department of Mines and Energy (NSDME) Riverside Corner 85-1 drillhole are presented here as a partial case history and prime example of the use of this method to interpret the complex structure of an evaporite deposit. Drilling of NSDME Riverside Comer 85-1 was conducted in late 1985and early 1986by the Department (Carter and Boehner, 1986) under a program to assess the potash potential of selected areas of the province as part of the Canada-Nova Scotia Mineral Development Agreement 1985-89. A reinterpretation of a portion of the available data from two exploration drilling projects on Cape Breton Island in the Canso-Bras d'Or area is also presented (see inset, Fig. I). Several drillholes have intersected the Windsor Group evaporite sequence in these areas and the available geophysical logs are a valuable tool in the interpretation of the structure of the deposits. However, no attempt has been made to present or discuss the detailed geological investigation and comparison of these two deposits. They are presented here as an example of the reinterpretation of existing data and their application to stratigraphic correlation and structural interpretation of complex evaporite deposits. Further work is necessary to document the stratigraphic and structural correlation of these two areas."

Jan 1, 1989

By E. L. Reed

This paper addresses the state and federal permit- ting requirements and regulatory constraints associated with the development of new "grass roots" surface coal mines in the Western United States. Since a major portion of new coal development in the West will be on federally leased coal in Wyoming, my comments are directed towards that geographical area. This will give the reader some insight into the current regulatory framework within which western mining companies must operate-i.e., the major applicable state and federal laws and regulations, the more important state and federal regulatory agencies, and the major construction and operating permits that are required. Before discussing the impact of the regulations on our business, I would like to tell you something of my company and then briefly discuss Exxon's forecast of the long range outlook for coal. Carter Mining is an Won affiliated surface coal mining company. Exxon became interested in the coal business in the mid 1960's with the recognition of the future need for alternative fuel sources. Since that time, it has acquired coal reserves located in Wyoming, Montana, North Dakota, Arkansas, Texas, Illinois and West Virginia. Carter's first surface mine, the Rawhide Mine, located north of Gillette, Wyoming began production in August, 1977. Our second surface mine, Caballo, located just south of Gillette, began operating last October. We have a third block of federally leased coal just east of Gillette. By 1985 we anticipate Carter's western surface mines will be producing at an annual rate of 30 million tons, subject, of course, to successful market development efforts and regulatory considerations. Rawhide will ultimately have a permitted capacity of 24 MM tons per year. The coal at Rawhide is in two seams; one 80 feet in thickness and the other 20 feet (including a 6 to 10 foot parting). A large shovel is used to remove the overburden, and a similar shovel and dragline are used to mine the coal. Caballo has a 75 foot seam; otherwise it is similar in design and operation to the Rawhide Mine.

Jan 1, 1979

By P. V. Fillo

This paper describes Mohave Mining and Milling Co. methods of mining and milling manganese ore in Arizona. It is one of a series of publications prepared by the Bureau of Mines on methods and costs in various mining districts in the United States. Production of manganese ore, as such, in Arizona began in 1915. Before this time manganiferous ores had been mined primarily for silver content and used as a smelter flux. From 1916 to 1918 approximately 69,000 long tons of manganese and mangsniferous ores were mined. After World War I production dropped to almost nothing until World War II, during which period more than 24,000 long tons were produced. A lull in mangonese mining occurred after World War II, having production rates of only a few hundred tons annually through 1952.

Jan 1, 1963

By J. Gartelmann, B. Zaslavsky, Y. Vojta, D. J. Chaiko, W. Mego, A. N. Rollins

"Aqueous biphasic extraction (ABE) processes offer the potential for low-cost, highly selective separations. This countercurrent extraction technique involves selective partitioning of either dissolved solutes or ultrafine particulates between two immiscible aqueous phases. The extraction systems that we have studied are generated by combining an aqueous salt solution with an aqueous polymer solution.We have examined a wide range of applications for ABE, including the treatment of solid and liquid nuclear wastes, decontamination of soils, and processing of mineral ores. We have also conducted fundamental studies of solution microstructure using small angle neutron scattering (SANS). In this chapter we review the physicochemical fundamentals of aqueous biphase formation and discuss the development and scaleup of ABE processes for environmental remediation.IntroductionAqueous biphasic extraction (ABE) is a highly adaptable separation technique that can be used in a wide range of applications. We have been evaluating various types of ABE systems for possible applications in the treatment of solid radioactive wastes (1,2), liquid nuclear wastes (3,4), and contaminated soils (5-7), and in the removal of organics from aqueous salt solutions (8). We have also conducted fundamental studies of the solution microstructure of ABE systems using small angle neutron scattering (SANS) (9).The extraction systems are generated by combining an aqueous salt solution and an aqueous polymer solution. This produces two distinct liquid layers that are as immiscible as oil and water, yet each liquid layer contains at least 70 to 80 wt % water. The biphasic systems that we have been working with consist of immiscible polyethylene glycol (PEG) and salt solutions. Some inorganic salts that promote biphase formation with PEG solutions include the sodium/potassium salts of sulfate, carbonate, phosphate, and hydroxide (10)."

Jan 1, 1996

By José R. de Tenorio

The aim of the present work was to investigate the reduction process of MnO~FeO-Si02 slags by carbon-saturated liquid iron. The effect of the initial Mn content in the bath was explored. The initial Mn content was in the range of 0 up to 40 wt. %. The MnO content in the slag was kept constant at 40 wt. %. Tests were performed in laboratory apparatus. Samples of slags and bath were taken. In the first 5 minutes, it was observed a very strong reduction of FeO. This first step promoted a MnO-Si02 enrichment of the slag and a formation of CO bubbles, which increases the slag level. The increase ofMn content decreases the MnO reduction rate.

Jan 1, 1996