Search Documents

By Yuan She, Qihang Liu, Keng Wu, Hailiang Ren

By observing different coal char’s microstructures and microscopic morphologies during the coking process, the characteristics of COREX coal char’s microstructure and properties were analyzed. MCRI and MCSR were used to respectively describe the reactivity and the strength after reaction of coal char, with those of BF’s coke for reference, and then the physical meaning of MCRI and MCSR were given. MCRI and MCSR were determined by the composition of coal char. For the two kinds of COREX coal, the formula to forecast the hot performance of coal char was set up by making a multiple linear regression between the hot performance and microstructure of the coal char at 1100℃, and the predictive values of coal char’s hot performance at 600℃, 800℃ and 1000℃ coincided well with the measured values.

Jan 1, 2015

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By A Gerdes, H BrStz, E GSbler, D Davis, F Henjes-Kunst, S Dewaele, T Graupner, T Oberthnr, M Sitnikova

Following the United Nations initiative to fingerprint the origin of conflict materials, the German Federal Ministry for Economic Cooperation and Development has decided to fund a pilot study on coltan ores. Since 2006, our working group has been investigating columbite- tantalite (coltan) mineralisation, especially in Africa, also within the wider framework of establishing certified trade chains. More than 300 samples were obtained from the worldÆs major coltan producing areas. Special attention is, however, directed to samples and concentrates from Ta-Nb-Sn provinces in Africa: Democratic Republic of the Congo, Rwanda, Mozambique, Ethiopia and Namibia. Using state of the art analytical tools, we investigate mineralogical and chemical parameters obtained from columbite-tantalite ores and concentrates in order to distinguish between ore provinces, likely even down to the deposit scale. Methods employed include fully automated electron microscopy (mineral liberation analysis), electron microprobe analysis (major and minor elements), laser ablation plasma-source mass spectrometry (trace elements and U-Pb dating), X-ray fluorescence spectroscopy (bulk major and trace elements), X-ray diffraction analysis (mineralogy and structure) and thermal-ionisation mass-spectrometry (U-Pb dating). Major and trace element concentration patterns, mineral assemblages in the ore concentrates, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Furthermore, the following age populations are evident:Archaean (>2.6 Ga);Palaeoproterozoic (1.9 - 2.1 Ga);early Neoproterozoic (æKibaranÆ; 0.98 - 0.93 Ga); andlate Neoproterozoic to early Palaeozoic (ca 0.5 Ga). Currently, we focus on the resolution of the fingerprinting system from region via ore province down to deposit scale. Our preliminary analytical results indicate that a certification scheme including fingerprinting of sources of coltan ores is feasible.

Jan 1, 2008

By Oliver Bowles

The use of fire as a source of heat was the first step from primitive existence toward modern civilization, and heat has performed functions of inestimable importance throughout the ensuing ages. The first commercial steam engine invented in 1698 demonstrated that heat was an important source of power, and heat has since become the motivating force for railroad trains and steamboats as well as for machines in multitudes of factories. Aside from its function of supplying power, heat is an agent of vast importance in chemical reactions and engineering processes. Because of the high temperature of steam under pressure, losses by radiation from boilers and pipes become excessive unless the radiating surfaces are covered with insulating materials. Insulation is important also for hot-water pipes and many other types of equipment from which heat may radiate. Radiation losses from heated surfaces increase rapidly

Jan 1, 1943

Controlled Blasting, Inc. (CBI) located in Norcross, Georgia recently teamed with the Dekalb county fire marshals office to stage a mock disaster to test new trainees of Community Emergency Response Team (CERT). It as an interesting example in which industry can help out the community and government through the use of explosives.

Jan 1, 2010

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By Floyd G. Anderson

The increasing trend toward use of continuous-type mining machines created a significant dust problem in coal mining, which resolved itself into three categories: Visibility at face, deposition on return airways, and the potential health hazard. The control measures applicable to these conditions and studied or developed from 1955 through 1957 are summarized and reviewed in this report. Other important problems brought into focus during the same period were radiation exposure in uranium mining and high temperature and humidity. Although temperature and atmospheric pressure alone may not be contributing factors in the incidence of silicosis, the few mining companies who operate under the extremes of these conditions are dust conscious and keep dust-control engineers on their operating staffs.

Jan 1, 1961

Legislation introduced for Queensland and New South Wales Coal mines provides different levels of prescription regarding specification of mine seals û generally in relation to capacity to withstand overpressure. In Queensland, the Coal Mining Safety and Health Regulation (2001), Section 341 (d) places a further onus on the statutory ventilation officer to æensure all ventilation control devices at the mine are properly constructed and maintainedÆ and that the ventilation officer æmust ensure a ventilation control device mentioned in the regulation à and installed at the mine meets the design criteria statedÆ for the ætype of deviceÆ. Based on the experience of the author, it appears that risk management and life cycle approach to seals has not been adopted to the same extent as for other aspects of operations. Further, because of the number of disciplines and personnel involved that may influence various factors affecting seal integrity, the opportunity for oversight or unclear allocation of responsibility is considerable. While suppliers can provide explosion or design rated seals, this should only be a starting point for application of the product in a coal mine. Application is often considered by mine planning staff (taking into consideration mine environment parameters such as water, control of gas, spontaneous combustion risk, etc) in conjunction with the colliery ventilation officer, and then construction completed by contractors under supervision of operational staff. After construction, seals often are managed by operational personnel with input from the ventilation officer. Input of the geotechnical engineer into pillar design, roadway opening size, ground support specification and most stable seal location is also required. The need for a customised design approach for each seal site is proposed in order to take into account the many and variable factors that may influence a site so that improved seal performance reliability and predictability can be developed. A program of quantitative as well as qualitative monitoring of performance and triggers for rectification or maintenance action is required, and would provide support to the aforementioned proposal. Many mines rely on visual/audible inspection and periodic bag sampling as the primary means of assessment. Other significant factors such as seal material properties, rib degradation, convergence, floor heave, effects of water on both structural integrity of the seal as well as the air tightness of the seal do not generally receive the same level of attention. Based on the above observations, the author has compiled a reference checklist in regard to the above matters, including aspects of and approaches to mine and pillar design, geotechnical modelling and data collection, civil engineering design, site evaluation and practical options available.

Jan 1, 2005

By J. A. Eisele

The Bureau of Mines conducted bench-scale cyclic tests to determine the composition of recycled leach liquor in the Bureau?s proposed clay/HCl leach/ HCl sparge process for producing Al203 from clay. The data developed from these tests make it possible to synthesize leach liquors for predetermined steady-state operating conditions when conducting large-scale crystallization tests. The results of two sparge tests were compared. One was a 20-cycle test with a 36-pct-HCl concentration in the mother liquor; the other was a 10-cycle test with a 26-pct-HCl concentration in the mother liquor. The effect of impurity concentrations in the leach liquor on the purity of aluminum chloride (AlCl30?6H20) crystals was determined, but there was poor correlation between this data and results that have been obtained from miniplant-scale work.

Jan 1, 1980

By J Crosbie, M Lord, R Bitencourt, P Defferrard

The MMG Century mine, which is the largest zinc/lead mine in Australia, began operating in 1999 and ceased mining from the open pit in July 2015, with processing completed in early 2016. Closure plans were developed from 2006, and detailed planning for closure commenced in early 2011 with the appointment of a dedicated closure planning resource. The site will continue to be managed during the active and passive closure phases to complete rehabilitation commitments and demonstrate that closure completion criteria have been achieved.Completion of the mining/processing phase of the project provides an opportunity to reflect on successes, missed opportunities and lessons learnt with respect to planning and execution of mine closure. This paper highlights examples of success at Century and also identifies key learnings and areas for improvement in progressive closure outcomes. Specific examples examine mine planning and execution involving bulk movement of waste rock and construction of permanent waste encapsulation landforms. The paper also provides recommendations for other sites that are planning for closure.Decisions made during the operational phase of the project life can result in a significant increase in closure liability and reduce the likelihood of achieving lease relinquishment. Likewise, it is of paramount importance to assess the consequences and thoroughly understand the risks associated with changes or deferral of closure plans, progressive rehabilitation targets and closure related key performance indicators.CITATION:Lord, M, Bitencourt, R, Crosbie, J and Defferrard, P, 2016. Closure planning lessons Learnt from the Century mine, in Proceedings International Mine Management Conference, pp 207-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 22, 2016

By Jacque Turgeon, Gontran Foy

"The Mineral Research Centre of the Quebec Department of Energy and Resources has worked extensively on the development of a dry process to extract pure mica flakes from a phlogopite ore. The liberation of mica from the gangue is effected basically by impact crushing, and the ground ore is screened into several fractions, each having a fairly narrow range of grain size. Each sized fraction is then fed to an air separator where heavy grains are separated from light flaky grains. Heavy fractions are returned to hammer mills where gangue minerals are ground finer and blocky mica particles are exfoliated. A second stage of screening is performed and each fraction is sent to an air separator. This sequence is repeated until mica products are virtually free of gangue. These different fractions are then treated in a cage mill in which mica flakes undergo a more orderly exfoliation along cleavage planes. The ground mica is again submitted to a final screening stage, after which each fraction constitutes a final commercial product.This process permits the recovery of about 70% of the mica contained in the ore. The over-all process will be described along with technical details of each unit operation. Recent work on a wet grinding method to produce very fine mica will also be discussed.IntroductionRecords of production of mica in Quebec date back to 1886. Production has been more or less continuous since that time, with peak activity during the war years. Production was interrupted in 1966, but started again in 1972 when Marietta Resources and Laviolette Mining and Metallurgical Corporation started their joint operation in Canton Suzor, northwestern Quebec. Mica deposits of more or less importance exist in different parts of Quebec, of which three have attracted attention in recent years: the Canton Suzor deposit, the Canton Lamy deposit and the Canton Chasseur deposit. The Suzor orebody was first identified by Carl Faesler in 1936, who described the rock as ""brown biotite in flakes half an inch in diameter, with interstitial augite, apatite and feldspar""."

Jan 1, 1982

By S. E. Vanderslice, J. A. Hummer

"The results of laboratory evaluations were used to compare the potential of two alternative, biomass-derived fuels as a control strategy to reduce the exposure of underground miners to aerosols and gases emitted by diesel-powered equipment. The effects of fatty acid methyl ester (FAME) biodiesel and hydrotreated vegetable oil renewable diesel (HVORD) on criteria aerosol and gaseous emissions from an older-technology, naturally aspirated, mechanically controlled engine equipped with a diesel oxidation catalytic converter were compared with those of widely used petroleum-derived, ultralow-sulfur diesels (ULSDs). The emissions were characterized for four selected steady-state conditions. When fueled with FAME biodiesel and HVORD, the engine emitted less aerosols by total particulate mass, total carbon mass, elemental carbon mass and total number than when it was fueled with ULSDs. Compared with ULSDs, FAME biodiesel and HVORD produced aerosols that were characterized by single modal distributions, smaller count median diameters, and lower total and peak concentrations. For the majority of test cases, FAME biodiesel and HVORD favorably affected nitric oxide (NO) and adversely affected nitrogen dioxide (NO2) generation. Therefore, the use of these alternative fuels appears to be a viable tool for the underground mining industry to address the issues related to emissions from diesel engines, and to transition toward more universal solutions provided by advanced engines with integrated exhaust aftertreatment technologies. IntroductionDiesel engines have been the workhorses of modern society for industrial and transportation enterprises. Diesel engines of all generations are extensively used in a variety of light-, medium- and heavy-duty applications in underground mining operations around the world. Fuels obtained from various sources and with wide-ranging chemistries have been combusted in diesel engines. However, the bulk of the currently used fuel can still be traced to nonrenewable petroleum sources. The petroleum-derived diesel fuels are primarily made up of saturated acyclic hydrocarbons (parafins or alkanes), aromatic hydrocarbons (arenes or aryl hydrocarbon), and unsaturated hydrocarbons with double bonds (olefins and alkenes). Improvements in the quality of petroleum-based diesel fuels was identified in federal regulations as an important piece in resolving the puzzle of diesel engine emissions (Environmental Protection Agency, 2001, 2004). The reduction of U.S. diesel fuel sulfur content below 15 ppm had the effect of lowering sulfate emissions and enabling the development and implementation of catalyzed emissions control technology across a wide spectrum of applications."

Jan 12, 2017

By R. R. Wells

This report summarizes the results of preliminary mineral-dressing studies by the Bureau of Mines on five samples of copper-bearing ore from various Alaska de-posits. The work on each sample was not extensive enough to warrant individual publication. The results, however, indicate the possibilities and limitations of concentration of the respective ores. The information therefore may be helpful in future development of these ore bodies. Four of the five samples tested were submitted to the laboratory by engineers of the Bureau of Mines as part of the examinations and survey investigations of strategic-mineral deposits in Alaska. This program is conducted to assist development of mineral resources in the Territory and particularly to aid economic exploitation of marginal or complex ores. The fifth sample was submitted by engineers of the Defense Minerals Exploration Administration.

Jan 1, 1956

By Peter Kreisman

This paper and four other papers on the MEQB Regional Copper-Nickel Study, presented today at the 1980 SME-AIME Fall Meeting are based on four years of extensive inter-disciplinary research and impact analysis supported largely by the Legislative Commission on Minnesota Resources. This study produced over 180 technical reports, the results of which are summarized in an Executive Summary available from the Minnesota State Planning Agency, St. Paul, Minnesota. Those wishing to examine the many scientific, engineering, environmental, social or economic issues addressed by the study are encouraged to obtain a copy of the executive summary. The executive summary includes a bibliography of all technical reports produced by the Regional Copper-Nickel Study and describes the five-volume, 26 chapter Regional Copper-Nickel Study Report.

Jan 1, 1980

By Louis Huntoon

HISTORY of the Porcupine area has been pub-lished in detail by the Ontario Bureau. of Mines in several issues of its annual reports. An. interesting volume could be written on: this topic; especially if personalities were introduced, such as the. transaction whereby the original title to the Hollinger group of claims was settled between Ben Hollinger and Alex Gillies by the toss of a coin. The early history of the McIntyre mine also had its thrilling events, such as its manager, R. J. Ennis, dodging the sheriff and deposit-ing red-hot gold bricks in the bank to meet his pay-roll. The occurrence of quartz veins containing low gold values was reported in 1896 by E. M. Burwash and again in 1899 by W. A. Parks. The first application for a mining claim appears to have been applied for on Dec. 30, 1906, by W. 0. Taylor, of Toronto, one of the old employees of the Hudson Bay Co. On the recom-mendation of Mr. Taylor, early prospecting was done on the shores of Porcupine Lake. It. was not until the spectacular discovery of the surface croppings at the Dome mine, by J. S. Wilson in 1909, that a rush to the district took place. Exploration was carried on during 1910 and 1911. The big boom was on in 1911, when claims sold on the evidence of mere rock croppings, owing to the prevailing heavy overburden. Rock croppings with specks of gold brought big prices. The country was heavily timbered and most difficult to prospect. My first trip was made during the summer of 1911, while the railroad was under construction from Porquis Junction to South Porcupine. I published my observations in the Canadian Mining Journal, Dec. 15, 1911, discussing in particular the character of the ore deposits and the future prospects of the camp. The first mills were erected in 1911, only to be destroyed by the disastrous fire in July of that year. They were rebuilt and the first important shipments are recorded in 1912. The history of the camp from the discovery of the Dome to the present consists of alternate chapters of great optimism and those of a more non-committal nature. For the engineer unfamiliar with the character of the deposits of this area, and the north country in general, it is at times most difficult to draw conclusions and submit definite recommendations. When valuable orebodies apex at depth, with no surface showings other than slightly mineralized veins of quartz or quartz containing a little visible gold; when at depth valuable veins and ore deposits, paralleling the one being explored, are developed by cross-cutting, such as Nos. 85-58 on the Hollinger, which have been its largest producers, the engineer assumes responsibilities rarely called for in other mining districts. This fluctuating aspect is exemplified in the three large producers, and may be duplicated with some of the old producers now being explored.

Jan 8, 1923

Underground space can be defined as space below natural ground level which can be used as an alternative to an above ground location. While many of our above ground structures inherently involve underground excavation for foundations and services, the term underground space specifically refers to organised development of underground openings and of the underground domain. For example, the services to a city such as power, gas, sewerage, water and communications are installed in a congested array which usually requires roads to be dug up when the services need to be accessed. An underground space installation of services would involve a well planned conduit which is easily accessed without any excavation. The concept of using this virtually untapped land resource to the advantage of our expanding cities is gaining considerable interest in Australia. Overseas, in the Scandinavian countries and some Asian countries, underground space has been used for centuries; in Great Britain, France and the United States of America over the last century and in Japan for over a decade. This paper focusses on the types of underground space usage which should be competitive with above ground use and suggests areas in which the competitive edge may be improved in favour of underground space. In particular, considerable advantage is seen by using well-planned underground space developments in major cities, where the strategic central location of the development takes advantage of proximity to potential users. However, the largest single factor affecting the acceptance of underground space is the high capital cost of construction, even though an underground space development may result in lower operating costs and reduced long-term maintenance costs. While excavation methods and associated costs are very much site-specific, the importance of applying the latest technology in rock breakage, with consideration of ground vibration, excavation rates and ground support, remains a major challenge to the development of underground space.

Jan 1, 1995

During the first quarter of 1973 ADL worked closely with PMSRC staff, under an extremely compressed time schedule, on all aspects of the detailed planning, organization and overall coordination and preparation of the lectures and in-mine demonstrations for the Bureau's Technology Transfer Seminar on Mine Communications given in March of 1973 to representatives of the mining industry. Our efforts centered on the detailed organization and preparation of each of the five technical seminar lectures and associated supporting material, and the coordination of tasks assigned to ADL and other seminar participants. Revised and expanded drafts of the seminar papers were prepared from rough draft versions obtained from PMSRC, Collins Radio and ADL staff. Measurements were made to gather key data on the operation and performance of each of the following systems installed in the Bruceton Safety Research Mine; call alert paging, roof bolt paging, section wireless radio, and guided wireless radio systems. These data were analyzed, manufacturer's equipment specifications utilized, and calculations made to provide performance curves and data for each of the above systems. A substantial amount of artwork was conceived and prepared for 35 m slides, system identification posters in the mine, and seminar handouts. This artwork included some forty 8-1/2" x 11" line sketches, graphs, block diagrams, circuit diagrams, coverage maps, and other line drawings; five 30" x 40" block diagram system identification posters suitable for in-mine use; a 20" x 30" detail perspective illustration of a representative coal mine layout; forty viewgraphs; and seventy 35 m slides of the artwork and word charts. Conferences, discussions and review sessions were held with conference participants to help coordinate the various efforts, obtain technical information, and make final plans regarding the lecture presentations, associated visual aids, and the communication system installations to be demonstrated in the Bruceton mine. These meetings included final systems checkouts and dry run presentations and reviews of the lectures and mine demonstrations. This phase of the seminar effort concluded with R. Lagace and R. Spencer of ADL participating in two days of seminar presentations in the lecture hall and in the Bruceton mine.

Jan 1, 1974

By Felipe Darabas Rzatki

Polyether ether ketone (PEEK) is a high performance thermoplastic often selected for high temperature tribological applications under chemically aggressive environments. The present work evaluate the tribological behavior of a high performance PEEK composite under ambient and high temperature (30 and 80°C, respectively). The atmosphere was also varied (air or tetrafluorethane). An AMTI tribometer equipped with a hermetic chamber and a heating system was used to carry out sliding tests of PEEK cylinders on 304 stainless steel polished discs (Sq < 10 nm) with reciprocating movement and 175 N normal force. Surfaces roughness analyses were performed with a white light interferometer. As expected, there was a strong influence of temperature on the tribological behavior of the samples tested in ambient atmosphere (25% decrease in friction coefficient associated with a 100% increase in wear rate). On the other hand, samples tested in tetrafluorethane atmosphere showed no significant friction temperature dependence.

Jul 31, 2018

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau&apos;s three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau&apos;s cover-coring method for determining rock stress.

Jan 1, 1985

By R. M. Brick, R. G. Treuting

DESPITE the basic importance of slip in the plastic deformation of metals, and the considerable experimental investigation, thought, and speculation that have been devoted to the fundamental nature of these processes, surprisingly few data have been reported regarding the microscopic appear- [ ] ance and distribution of slip lines,[$] the external manifestation of the slip process. Photographs hitherto reproduced in the literature are in general at low or unspecified magnifications with no correlation to the prior shear. A single-crystal cylindrical tensile specimen of alpha brass about ½ in. in diameter, one of many previously prepared by H. L. Burghoff,1 was available for study. A plane about 3/16 in. wide, parallel to the specimen axis and normal to the plane containing the slip direction and the specimen axis, was ground and metallographically polished along the entire 5-in. gauge length. Heavy etching produced a surface free of both scratches and flow. The specimen was strained in tension until slip markings first became visible on the polished surface (Figs. I and 2). Restressing the crystal caused additional markings to appear at an initially lower [ ] stress than previously was required. Stretching the specimen to produce a dense concentration of slip lines caused such variations in level in the polished surface (normal to the slip direction) that microscopic study at higher magnifications became impossible. After annealing 15 hr. at 850°C., the specimen recrystallized to form two grains with a boundary approximately normal to the specimen axis and about midway along its length. Each was X-rayed, and two planes were again polished along the length of the specimen, in this case each parallel to the slip direction in one of the two crystals. A light longitudinal scratch parallel to the specimen axis was drawn down the center of each plane. A Huggenberger extensometer was attached to the crystal A, whose slip plane would have the higher resolved shear stress of the two, and the specimen was again strained in tension.

Jan 1, 1941