Search Documents

By Singh DP, Singh TN

The present study attempts to critically review the pillar-design as required by Coal Mines Regulations of India vis-a-vis latest rockmechanics formulae. Equivalent material modelling was the approach adopted for testing the safety and stability of the pillar sizes predicted by various formulae. Two parameters, considered here for calculating pillar sizes was the stresses acting over the pillars and the strength of the pillars. Stresses acting on the pillars were calculated by the tributary area method. Based on the studies of Coates and Hustrulid, the stress obtained was reduced by 40 percent. For calculating the strength of the pillars, three formulae, namely Holland and Gaddy, Salamon and Munro and Central Mining Research Station, India, were used. The pillar widths were then determined by equating the product of recommended factor of safety and pillar stress with the pillar Strength.

Jan 1, 1992

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

By G Richmond, J R. Glen

Western Metals Mt Gordon Operation is a copper mine and processing plant situated 120 kilometres north of Mt Isa. The unique Mt Gordon copper process utilises a whole of ore acid/ferric pressure leach to produce copper cathode from the Esperanza massive sulfide copper orebody. Esperanza ore contains chalcocite, covellite and minor chalcopyrite hosted in a massive pyrite matrix. These ore stocks will be depleted in late 2003. Recently the process circuit has been upgraded to allow the treatment of lower grade Mammoth ores. These include the installation of a ball mill to complement the existing SAG mill, a single stage rougher flotation circuit and a tailings thickener. The leach bleed neutralisation plant was also upgraded at this time. Commissioning of these new circuits occurred in March 2003 and involved all the challenges of ensuring current production levels were successfully maintained while new process steps were incorporated into the whole circuit. This paper explains the background flow sheet of the patented Mt Gordon process and the reasoning behind the enhancements required for an already successful copper leaching circuit. Included are discussion of the influences of the new ores on individual process components such as comminution, leach chemistry and solid/liquid separation. Longer term ore processing options are also discussed.

Jan 1, 2003

By Rudolf E. Greuer

Every mine contains inflammable materials, either in form of the minerals mined or in the form of brought-in supplies. Although great efforts are made to make mines as far as possible fireproof and to prevent ignition sources, the possibility of mine fires, like that of other accidents, will always continue to exist. Detailed statistics are available for coal mines. They show (65,112) that the number of major mine fires in the USA over the last 20 years has remained more or less constant with approximately 50 per year. The same number is reported (26) for the British coal mines. Other countries (147) report about 1 major fire for every 10 million tons of coal production. Conflicting data are published on the number of fatalities caused by fires, presumably because frequently deviating opinions on the cause of death exist. On the average (82,99) 4 miners are killed per year in the US and in the British coal mines. Although this number is much smaller than that for several other causes of fatalities, one must keep in mind that almost every small fire can develop into a large disaster.

Jan 1, 1973

By Isabel F. Barton, MarkD. Barton, Christian A. Rathkopf

Molybdenite is the world’s principal source of rhenium (Re), a critical element in multiple high-tech applications. However, the Re contents in molybdenite vary by orders of magnitude on scales ranging from single grains to whole deposits. In order to better understand the systematics of this variation and what geochemical factors control molybdenite Re concentration, and hence overall Re resources, we examine global patterns in molybdenite Re contents through a compilation of > 3000 measurements of Re in molybdenite from > 700 mainly ore-bearing moderate- to high-temperature hydrothermal systems of different types. Our results are similar to but expand on those of earlier studies. Rhenium concentration in molybdenite has a lognormal distribution and varies systematically with type of geologic system, intrusive lithology, and Mo grade. The lowest-Re molybdenite occurs in greisens (geometric mean 1 ppm ± a multiplicative standard deviation of 9), quartz vein-hosted W-Sn deposits (2 ± 5 ppm), unmineralized granites and granodiorites (12 ± 8 ppm), intrusion-related deposits (24 ± 8 ppm), and porphyry W-Sn deposits (16 ± 11 ppm). Rhenium is most enriched in molybdenites from volcanic sublimates (23,800 ± 5 ppm), with skarn Fe and Au (560 ± 5 ppm and 540 ± 3 ppm respectively) and porphyry Cu and Cu-Au deposits next (470 ± 4 and 430 ± 7 ppm respectively). Among porphyries, skarns, and quartz vein-hosted deposits, Re is most highly concentrated in molybdenites from Cu and Au systems and its concentration decreases systematically through Cu-Mo, Mo, Sn, and W deposits. In nearly all cases, molybdenites from systems associated with intermediate igneous rocks contain more Re than molybdenites from systems of the same type with more felsic rock associations. The disparity between Re contents of molybdenite in felsic and intermediate systems is largest for porphyries, quartz vein-hosted, and skarn deposits and is near zero for subeconomic or barren granite and granodiorite Mo systems; felsic intrusion-related deposits have slightly higher molybdenite Re than their equivalents associated with intermediate intrusions. In most systems, molybdenite Re content does not correlate with metal grade, but may have an inverse correlation with Au grade in intrusion-related deposits (based on a small number of data points) and does exhibit a strong inverse correlation with deposit Mo grade. Dilution of Re through larger amounts (higher deposit grades) of molybdenite explains about 40% of this correlation, but the relative enrichment of Re in molybdenite from low-Mo deposits must also reflect some selective enrichment of Re/Mo in porphyry Cu systems compared to porphyry Mo systems. We found no evidence for secular increase or other systematic temporal variation in molybdenite Re content. The data regarding the use of molybdenite Re content as a proxy for mantle influence are ambiguous. Nearly all observed empirical correlations can be traced back to differences in redox state and sulfide concentration, the two geochemical factors identified here and by previous experimental work as the controlling influences on Re mobility under hydrothermal conditions. Hydrothermal systems with reducing conditions (W- and Sn-rich) tend to have low molybdenite Re even though compiled whole-rock data indicate that their source rocks have as much or more Re as those of more oxidized systems (e.g., Cu-rich). Vapor-phase exsolution, crustal assimilation, and mixing with external fluids may all enrich molybdenite Re concentrations in individual deposits and deposit types, but their extent and importance in overall hydrothermal concentration of Re is uncertain. Thus, it appears that the available molybdenite Re resource in an ore deposit largely depends on how the deposit’s redox and sulfidation conditions have varied over time and space during the timespan of hydrothermal activity. Oxidized, high-sulfide conditions tend to concentrate Re in molybdenite, whereas reducing conditions tend to leave Re dispersed at low concentrations in the bulk rock.

By R. J. Munday

Although uranium deposits in northern Saskatchewan are clustered around the Athabasca basin, basement lithostructure determines their distribution. Basal Wollaston Group pelites are invariably graphitic and carry uraninite in felsic segregations and biotitic pegmatite. Where these intersect the Athabasca Formation, remobilized uranium concentrated as pitchblende. Uranium is also concentrated in silicified and hematized sandstone where the Athabasca Formation overlies post-orogenic faults. Presumably, pregnant solutions associated with the fault were stripped of their metals as they emerged into the contrasting physico-chemical environment of the sandstone basin. Both these types of mineralization correlate with a Grenvillian (-1,000 m.y.) heating event and associated diabase intrusions. However, the rich pitchblende veins at Uranium City appear to predate the Athabasca Formation, but display spatial correlation with the Martin Formation. They are tentatively associated with a syn- to post-D3 retrograde metamorphic event which thoroughly leached crystalline basement and generated uraniferous fluids which escaped, and precipitated metals, into fractures associated with faults that define the grabens in which the Martin Formation was deposited. Remobilization events allowed some of this uranium to move upward into fractures within Martin sediments.

Jan 1, 1979

By G. J. Hasenfus

There are no known published methods of estimating the degradation of coal measure rocks by water that are simple and efficient, yet still provide a quantitative, meaningful value for assessing the stability of coal mine floor, roof, and rib. The slake durability test, the standard index method for estimating the durability of rock subject to wetting, can provide misleading results for floor stability assessment. Additionally, slake durability testing is time consuming and requires specialty equipment. Methods based on humidity cycling have been demonstrated to be very effective for assessing coal mine roof, but require specialty equipment and do not address floor stability concerns. Visual observation techniques, such as that developed for the Coal Mine Roof Rating (CMRR) method, adequately qualify rock degradation, but lack quantitative rigor. This paper will describe an alternative method, coined the water sensitivity test, originally developed for floor stability analyses, but also found applicable for roof and rib stability assessment. The test was developed by CONSOL in the early 1990's, and in its current form, has been in use for approximately twelve years. The method is based on the basic slake durability principle of measuring the mass of the rock retained on a screen after submersion in water. The new test employs two screens of different sizes, and also uses modified submersion, drying, and data processing procedures. The method is relatively efficient and can be geared toward batched testing. As with the slake durability test, the resulting index value provides a quantitative measure of the susceptibility of rock to water degradation. In addition to discussing the test method and its development, this paper provides a comparison of results with those fiom standard slake durability tests, and tabulated results for various types of coal measure rocks. Examples of the technique's utility are provided, including assessment of longwall and development floor conditions, roof and rib rock weathering and stability, and drum-bit cutability.

Jan 1, 2005

By JOHN HOMER, Jacob L. Carr, Jonathan K. Hrica, Kathleen M. Stabryla, Iman Benbourenane, Jennica L. Bellanca

Given the recent focus on powered haulage incidents within the US mining sector, an appraisal of collision avoidance/warning systems (CXSs) through the lens of the available research literature is timely. This paper describes a rapid review that identifies, characterizes, and classifies the research literature to evaluate the maturity of CXS technology through the application of a Technology Readiness Assessment. Systematic search methods were applied to three electronic databases, and relevant articles were identified through the application of inclusion and exclusion criteria. Sixty-four articles from 2000 to 2020 met these criteria and were categorized into seven CXS technology categories. Review and assessment of the articles indicates that much of the literature-based evidence for CXS technology lies within lower levels of maturity (i.e., components and prototypes tested under laboratory conditions and in relevant environments). However, less evidence exists for CXS technology at higher levels of maturity (i.e., complete systems evaluated within operational environments) despite the existence of commercial products in the marketplace. This lack of evidence at higher maturity levels within the scientific literature highlights the need for systematic peer-reviewed research to evaluate the performance of CXS technologies and demonstrate the efficacy of prototypes or commercial products, which could be fostered by more collaboration between academia, research institutions, manufacturers, and mining companies. Additionally, results of the review reveal that most of the literature relevant to CXS technologies is focused on vehicle-to-vehicle interactions. However, this contrasts with haul truck fatal accident statistics that indicate that most haul truck fatal accidents are due to vehicle-to-environment interactions (e.g., traveling through a berm). Lastly, the relatively small amount of literature and segmented nature of the included studies suggests that there is a need for incremental progress or more stepwise research that would facilitate the improvement of CXS technologies over time. This progression over time could be achieved through continued long-term interest and support for CXS technology research.

Jun 17, 2022

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By J D. Grobler

In the heavy minerals industry wet high intensity magnetic separators (WHIMS) are widely applied for primary magnetic separation of magnetic minerals and non-magnetic minerals. This piece of equipment is well known for its robustness to handle a wide range of feed conditions and still produce stable product qualities and yields. A heavy mineral production plant aimed to increase production through their WHIMS plant containing 11 duties and 26 units. Instead of adding new units an alternative approach was followed to firstly maximise the efficiency of the current circuit and secondly to consider possible reconfiguration of the circuit to produce additional product tons for minimal capital investment. In order to characterise the current circuit’s efficiency, identify pockets of excellence and determine the areas for improvement the whole circuit was surveyed several times and mineral mass balances were drawn up.This paper aims to: discuss the modelling process of the WHIMS circuit,explain the calibration and validation process followed to ensure the accuracy, anddemonstrate the sensitivity analysis performed on the different options. From this analysis an efficiency criteria was developed to compare different circuit configurations that enabled the production plant personnel to make an informed decision on the way forward.

Oct 5, 2011

By Oliver C. Ralston

Fluorescence is of growing interest to the mineral industry because certain minerals may be detected thereby and because, as shown in figure 1,4/ many minerals (natural or synthetic) are needed in tubes and lamps. The use of fluorescent lighting is expanding, and large numbers of lamps of many sizes and shapes are being made and used in works, factories, stores, offices, homes, and in photography. Fluorescent tubes, as distinguished from clear tubes filled with neon, argon, or other rare gases through which a current of electricity passes, fluoresce owing to specially, selected and prepared minerals placed in the tubes. Luminous chemicals and paints also contain special minerals and are used in similar applications; therefore, these also will be considered in this report. Although the quantity of minerals (in tons) that are used for fluorescent purposes is small, and probably will continue to be so, this use is significant because it exemplifies a requirement for "pure" minerals in which a trace of contaminant as" minute" as one part in ten million may distinguish between the acceptance or rejection of a particular material. This extreme purity makes synthetic minerals almost essential, and natural mineral's are now little used.

Jan 1, 1944

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By H. F. Weaver

The 17th National First-Aid and Mine Rescue Contest was held in the Kentucky Fair and Exposition Center, Louisville, Ky., October 2, 3, and 4, 1957. The meet was under the auspices of the Federal Bureau of Mines and the Joseph A. Holmes Safety Association, in cooperation with the National Coal Association, United Mine Workers of America, State mining departments, local mining institutes, and coal operators' associations. The Arrangements Committee, as authorized by the General Committee, made all the necessary arrangements for conducting the 1957 contest. Members of the Arrangements Committee were: Harry Gandy, Jr. (chairman), National Coal Association; James B. Benson, Southern Coal Producers' Association; Charles Ferguson, United Mine Workers of America; George C. Trevorrow, Bituminous Coal Operators' Association; and James Westfield, Federal Bureau of Mines.

Jan 1, 1958

By J. P. Morris

A diphenyl ether calorimeter for measuring high-temperature heat contents of ferrous alloys and iron-and steelmaking slags was constructed and calibrated with specimens of molybdenum, alumina, and platinum that were heated to temperatures ranging from 1,720° to 1,875° K. The standard deviation of the calibration measurements was 0.37 percent. By measurements of the enthalpy of delta and liquid iron, the heat of fusion of iron was found to be 3,298 ±100 cal per mole.

Jan 1, 1966

By K. Janghorban

Multilayered ceramic-metal composites were produced by solid state diffusion bonding of polycrystalline alumina and three Al alloys containing 1 to 2%Sr, 2% Mg and Mg + Si (5057 Al alloy), The multilayered structures were fabricated at 610°C under a compressive stress of 3 MPa for 2 hours in He-5%H atmosphere, The ceramic-metal interfaces were studied by SEM and TEM equipped with energy dispersive spectrometer (EDS). Addition of 1 wt % Sr to Al promoted good adhesion, without producing any interfacial products, while the Al-2%Sr was poor in this regard due to the presence of dispersed A14Sr which is an intrinsic phase in the Al-Sr phase system, The Al-2%Mg alloy produced a continuous film at the interface, which was characterized to be MgAl2O4. Al alloys containing Mg and Si (5057 commercial alloy) produced not only the spinel structure (MgAl2O4), but another phase rich in Mg and Si (close to Mg2Si), These latter interfacial reaction products were not the intrinsic phases in Al-Mg alloys, and were reaction products at the Al2O3 ?Al alloy interfaces.

Jan 1, 2005

By A. G. Loomis

METHODS for measuring relative permeability as a valid function of saturation were compared by the. Bureau of Mines, using core samples from representative oil-productive California formations, from the Bartlesville sand in Oklahoma, and from synthetic samples. Measurements for gas-oil systems were made by steady-state dynamic, unsteady-state displacement and two stationary-phase methods. Measurements for water-oil systems were made by the unsteady-state displacement method. As the ratio rather than individual relative permeabilities is measured by the last method, three methods for calculating individual relative permeabilites from their measured ratio were compared for gas-oil systems and two methods for water-oil systems. Errors arising from capillary discontinuities, such as the end effect and stabilized-zone flow, are discussed and evaluated; possible errors rocs arising from turbulant flow are also examined. The inapplicability of non-steady-state methods for water-oil systems that are not definitely oil-wet is discussed in detail. Measurements of relative permeability to both gas and oil can be made quickly and accurately by the steady-state dynamic method when rates of flow of the two phases are sufficient to minimize the capillary discontinuity at the outflow end of the sample. At such rates relative permeability-saturation measurements are essentially independent of the rate of flow. The steady-state method wits modified by a dispersion section at the inflow end of the sample acid designated tie dispersed-feed method.

Jan 1, 1962

By Marcos Paulo Kohler Caldas

A recuperação de metais presentes em equipamentos eletroeletrônicos tem atraído interesse em virtude de novas e diferentes tecnologias que visam a reutilização desses elementos químicos em novos processos produtivos. A recuperação de metais das placas de circuito impresso tem atraído o interesse das empresas, pois, ao mesmo tempo que produz bons resultados do ponto de vista econômico, também se pratica o desenvolvimento sustentável, reduzindo a extração de metais da natureza. Este trabalho tem como objetivo caracterizar as placas de circuito impressos (PCI’s) de memória de computadores, através de imagens de microscopia eletrônica de varredura com espectroscopia por dispersão de energia (MEV/EDS), a fim de verificar a presença de metais, visando a sua recuperação.

Aug 17, 2017

By Dejan Petrović, Pavle Stojković, Jelena Ivaz, Saša Stojadinović

In spite of the fact that flyrock phenomenon represents the real threat for personnel and machinery, it still remains insufficiently investigated. There are efforts, in the mining community, to explain the causes of flyrock, but the models capable to accurately predict flyrock occurrence and define the flyrock distance still do not exist. This article is an attempt to establish such a predictive model. The model utilized the adaptive nature of artificial neural networks and combined it with the accuracy of numerical modeling of physical phenomena. Necessary data were collected by high-speed camera recordings of actual blasts at three different surface mines and processed for further use for artificial network training. The result was a neuro-numerical couple which was capable to predict flyrock occurrence, estimate the launch velocity of flyrock fragments, and calculate the maximum distance of flyrock fragments. The safe distance was then calculated by multiplying the flyrock distance with a factor of safety. The article explains the procedure for data acquisition and processing, artificial network construction, training, and validation. It also explains the principles of flyrock distance calculation and, finally, provides a definition of factor of safety and safe distance. The results showed that the prediction was satisfactorily accurate and reliable.

Oct 22, 2021

By Jerry B. F. Champlin

NIOSHAn accelerated testing procedure developed by the Bureau of Mines for evaluating commercially available corrosion inhibitors is described. Ultra-sonic agitation of the corrodent solutions and the hot-finished mild steel test coupons was used to evaluate the effects of several variables on the effectiveness of two corrosion inhibitors. Small changes in the weight of the test coupons in both controlled and inhibited corrodents, before and after exposure, affected the precision and accuracy of the results. Minute amounts of oxygen in the systems were found to be causing the relatively large deviations in the corrosion developed in the controlled tests. Microscopic examination of the test coupons revealed that both surface preparation and internal strains resulting from fabrication methods materially affect corrosion behavior.

Jan 1, 1965

By Chas. F. Jackson

The work of the mining division is divided between seven sections, each in charge of a supervising engineer, as follows: 1. Metal-mining methods section, the supervising engineer of which is also supervising engineer of the Southwest Experiment Station at Tucson, Ariz. 2. Metal-mining research section. 3. Nonmetal minim section. 4. Coal-mining section. 5. Mine-ventilation section. 6. Mineral-industries survey section. 7. Electrical section. The names of the sections indicate broadly the fields covered by each, and in the following pages the objectives and type of work of each section will be summarized briefly and the active problems listed. The work done during the calendar year 1936 will also be summarized.

Jan 1, 1937