Search Documents

By CORA ROELOFS

In the USA, miners are at higher risk for work-related disorders that could precipitate an opioid prescription, injury-related opioid prescriptions, and opioid overdose. We aimed to support prevention of these outcomes with an “opioid hazard awareness” miner safety training module. In January and February 2020, the training module was embedded within required mining safety and health training for stone, sand, and gravel miners in Massachusetts (USA). Training impact and reception were assessed with a pre- and post-training survey of trainee characteristics, training content knowledge, and attitudes. Over 800 miners were trained and over 600 responded to surveys. We found statistically significant improvements in opioid risk factor knowledge and knowledge of resources to help a coworker. Nonstigmatizing attitudes were high both at baseline and following the training. The training was perceived as relevant and useful by trainees. Improving opioid hazard awareness in high-risk worker populations has potential to reduce opioid dependence and downstream impacts including overdose death. Employer injury-prevention efforts should be reinforced while worker health and safety training enhances awareness of opioid-related harms and prevention strategies for miners and other high-risk worker populations.

Nov 19, 2021

By A D. Campbell

The Homer Tunnel is located in a remote area of the South Island of New Zealand and carries large numbers of tourists to Milford Sound through an avalanche prone area. The tunnel is 1280 m long with a steep ten per cent unidirectional grade descending to the west. Construction of the tunnel began in the 1930s and was completed to a nominal 6 m width in 1954. In 1996, two passing bays were stripped-out to accommodate bi-directional flow of tourist coaches. During all phases of construction and widening there have been episodes of strain bursting.The condition of the tunnel and standard of internal services is below current international practice, principally in terms of; in-tunnel air quality, fire life safety, ground support, and road safety. A number of near-miss events have occurred involving coach fires on the approaches and inside the tunnel. The national road authority, NZTA, is considering a substantial investment to improve amenity and safety of the tunnel.This paper describes the rationale for the proposed upgrade works and the investigations undertaken to enable that design. A holistic approach to road tunnel safety has been adopted that balances the key interrelated safety drivers, namely; tunnel lining, traffic operations, ventilation, power supply and egress while ensuring continuity of safe access to Milford Sound.

Mar 8, 2011

By A Palynchuk

The development of welded pipe has paralleled the general industrial development and, in particular, that of the petroleum industry. The petroleum industry's need for high-grade, economical pipeline material to make many 'of its projects feasible has been a significant factor in the development of light-wall, high-grade welded pipe. The modern welding processes, such as high-frequency, electric resistance, flash, submerged arc, etc., have some basically different characteristics. The modern high-frequency weld mill is a complex of specialized equipment that is integrated into a production unit. Each component in the unit performs a specific function in the production process. Quality control must be built into the process on an operating basis and, to maintain the quality required for pipeline standards, must be more than a policing operation. The further development of the welded pipe industry will be determined by changing and increasing demands. The technical and economic views and requirements that will influence the development have to be resolved.

Jan 1, 1964

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By K B. Bowley

This paper covers the application of a systematic maintenance plan by the Plant Engineering Department of Rio Algom Mines Limited, Milliken Division. The plan established the function of work study, developed and installed formal work planning and labour cost control procedures, and extended the existing preventive maintenance routines. In June, 1961, assisted by management consultants, a more scientific approach to maintenance was instituted. The emphasis was placed on the control of labour. The development and application of the primary control system was established with-in six months. Since then, the Department has operated for a year, consolidating the system. The procedure of the installation, the results achieved and the results to be expected will be discussed. JNTRODUCTION THE Milliken Division of Rio Algom Mines Limited operates a 3,000-ton-per-day uranium mine, in the Elliot Lake district of Ontario, which went into production in April of 1958. The lowest operating level is 3,000 feet below surface. Mining is carried out by open stopping, with planned pillar support and footwall haulage on rail.

Jan 1, 1963

By James L. Fenton

In its unending search for the raw materials that the affluent society of today requires the mining industry has found it necessary to go to great depths, in many cases, to produce these materials. Inherent with this problem is the insufficient technology relating to improving extreme environments that the mine personnel are exposed to. In this dissertation, the sources of heat flow into a mine along with the various effects that this heat has on the mine personnel are investigated. The object of dissertation is to compile all the available published information pertaining to these underground heat and their effects into one paper. This will provide the mining industry with an available easy-to-use to aid in the determination of mine ventilation requirements as the mines are in the phases of original planning or being extended to depth. Areas of significant, deficiencies it knowledge have been disclosed during this overall appraisal. Recommendations on important basic research needs are out lined for future consideration by Federal or industries sponsorship. This thesis should serve as a stimulus lo, future well-organized research efforts in the area of underground heat sources and their control.

Jan 1, 1973

By D. C. Yates, G. V. Jolliffe

In the five coalfields of Staffordshire, there have been some 43 incidents of spontaneous fires and heatings which have required special attention in the past ten years. This total excludes incidents in the Thick Coal Seam of South Staffordshire, which was worked until 1967, and which was subject to an almost continuous series of heatings. The incidents have been classified to show the sites of occurrence, the contributory factors which may have caused them and the treatments applied to them. The remedial techniques, as practised in Staffordshire, are dealt with in detail, with particular reference to standard methods of stopping-off. Precautionary measures taken are described, including a "liability to spontaneous combustion" classification of all seams, and the setting up of an emergency organization with emergency stocks of materials and equipment. The paper is concluded by a few words on the organization and control at the time of an incident.

May 23, 1905

By F. E. Diebold

The wastewater-treatment system of the Anaconda Mining Co., at its Butte, MT., operation has been physically and chemically characterize modeled on a computer and investigated with respect to alternate systems for economic heavy metal recovery. The system involves lime addition to a mixture of acid underground copper sulfide mine water, acid effluent water from the iron induced precipitation of copper from acid leach solution and basic suspensions of solid effluent from a concentrator plant. Experimental chemical analysis and predictive computer calculations shows that the monosulfllte and disulfllte complexes of transition metals (Iron II being dominant) and alkaline earths are 40% of the total dissolved metal load of both acid streams. The suspended solids (30% by weight) in the basic concentrator slurries are dominated by quartz and pyrite and also contain kaolinite muscovite, biotite and undissolved lime. The mixture of these three streams result's in major reductions in concentrations of Al, Cu, Fe, Mg, Mn, Sir and Zn, and a pH >7 with calcium, sodium, potassium, and sulfate being the major dissolved ions. The treatment system has been simulated in the laboratory and accurately modeled on a computer. The computer program, an altered REDEQL-EPAK, is capable of accurately predicting the amount of lime required to reach a desired effluent water. Preliminary research has indicated the usefulness of electroprecipitation as a means of recovering the valuable metal load and providing an EPA acceptable effluent.

Jan 1, 1982

By Scott Turner

Many of you radio listeners have probably never seen a mine . You may be glad of it, but you should not forget that there is a vast army of men in this country who not only have to see mines , but have to work in them day by day in order that you may be supplied with many of the things you need. Specifically , nearly a million men work in the mines of the United States , 700,000 in the coal mines , 110,000 in the metal mines , 100,000 in other mines and quarries , and 75,000 in the oil and gas fields . On a stormy night , the average citizen is apt to think of the perils of the seaman . Particularly in the old days before steamships , many a prayer went up " God help the poor sailor on a night like this . " At the same time , the sailormen often expressed fear for the poor landlubber , exposed as he was to the danger of falling chimneys , swaying signboards , and uprooted trees . So with the miner . Many of you may pity him , for working underground in complete darkness except for feeble artificial lighting , mining coal or ore , drilling hard rock , handling explosives , and perhaps breathing vitiated air . On the other hand , on stormy days , with rain , snow or hail falling , and with the temperature low , or on hot bright days , I have often heard miners joke about the poor fellows who had to stay " on top, " and could not get " down below" where there was no wind , where no snow fell, where the temperature was unchanging , and where a man could have his own working place , arranged to suit himself , with little interference from meddlers and with no automobiles to dodge . So do not feel too sorry for the miner . He is quite apt to be a strong , healthy , hearty person , making pretty good wages , and fairly well contented with his lot .

Dec 1, 1930

By PHILIP N. MOORE

THE development of the power of the Tennessee River at Muscle Shoals has become a matter of political interest as well as engineering possibility. The controversy over it has been so active that the facts have been obscured, the possibilities exaggerated. Although the members of the American Institute of Mining & Metallurgical Engineers are not generally specialists in hydroelectric development, those who visited Muscle Shoals in October, following the Birmingham meeting of the Institute, were interested, and many of them surprised to learn the actual conditions. These have long been familiar to those who have studied the matter through the reports of the U. S. Engineers on the subject. The approved plan contemplates three dams-No. 1, a low dam close to the City of Florence, planned in the interests of navigation, since the construction of the other dams has rendered impossible the use of the river without it. No. 2-named the Wilson Dam is now under construction. Concerning it political argumentation has waged. No. 3 Dam-much smaller, is planned to be erected several miles above No. 2.

Jan 1, 1925

By H. El-Faramawy, A. Ahmed, M. Eissa, M. El-Fawakhry, T. Mattar, S. N. Ghali, E. M. Kotb

As a result of the depletion of high-grade manganese reserves, it has become necessary to consider the exploitation of low-grade manganese ores. The main problem of low-grade manganese ore is the low Mn/Fe ratio, which makes it unfit for the production of manganese ferroalloys. In this work, a selective reduction technique was used for smelting low-manganese ore in the presence of coke and fluxing material in an electric submerged arc furnace to obtain a rich manganese slag and low-manganese pig iron. The product slag was blended with medium-manganese ore and smelted in an electric submerged arc furnace, in the presence of coke and the fluxing agent, to produce silicomanganese alloy. The influence of reducing agent ratio, charge basicity, and charge Mn/Si ratio on the smelting process was investigated. The optimum conditions were found to be a coke ratio of, 1.35, Mn/Si ratio of 2.0, and charge basicity of 2.5. The silicomanganese alloy produced under these conditions satisfies the specifications for Si16Mn63 and Si17Mn65. The experimental results were applied on a pilot scale, producing a silicomanganese alloy with a chemical composition close to that of the standard specifications.

Jan 2, 2022

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By Albert L. Toenges, Louis A. Turnbull, EDWARD L. FISH, JOSEPH J. SHIELDS, James J. Dowd

The stripping of coal with mechanical. equipment has progressed since the introduction of the first steam-powered shovel for the retóval of overburden at a mine in Pittsburg, Kans., in 1877...From the smart steam-powered shovels with dippers of less than a cubic yard capacity, small digging radius, and shovels that required manual moving, the trend has been toward large-capacity machines. Steam as power has been replaced largely by electricity, gasoline, and Diesel fuel, and dipper capacity as great as 35 cubic yards has been attained. Shovels and drag lines are self-propelled and revolve through 360°. The cost of these large-capacity modern machines is great, and in order to assure the return of the investment during the life of the property the reserve of coal in the area to be mined must be large;" Many comparatively small areas of coal suitable for strip mining exist, but these areas probably could not be mined, profitably with this large equip- ment. Therefore, heavy equipment has not been used in small areas because of the high cost in place of this equipment, the time and Atpense required to transport the machines to the mine site, and the construction of power lines if the machines are electrical powered.. Scrapers and light excavating equipment ane mobile, and the investment cost is not high. These units have been used in sirring the coal in small areas. A study to determine the methods in, yogue, and economic considerations involved in the use of such equipment was undertaken, and the information obtained is discussed in this report.

Jan 1, 1947

By M. L. Whisman

Three samples of waste lubricating oil were re-refined by processes developed by the Bureau of Mines and reformulated with additives to meet designated requirements for viscosity and service. Quality-defining bench-scale tests were used to compare and evaluate the quality of these three motor oils, eight commercially re-refined lubricating oils, and three new lubricating oils. Most of the re-refined oils studied could not be distinguished from new oils by the bench tests used to define quality. There was some evidence, however, that one and perhaps more of the re-refined products investigated might not meet all of the quality standards of new lubricating oil, suggesting the need for better quality controls by re-refiners.

Jan 1, 1974

By C. C. Herrick

The vapor pressure of indium has been measured by the torque-effusion technique, as a function of temperature between 1102o and 1422oK. For liquid indium, the vapor pressure (in atmospheres) can be represented by the equation -R In P = 5.782 x104/T - 25.29from 1000o to 1422oK. Extrapolation yields a calculated normal boiling point of 2329°K and a heat of vaporization at 298 oK of 58.09 kcal per mole by the third-law method and of 58.39 kcal per mole by the second-law method. Calculations indicate that the free-energy functions of Hultgren are to be preferred to those of Guruich. BECAUSE of the potential uses of liquid metals, it is important that convenient experimental methods be developed which will lead to a sufficient body of thermodynamic data so that reasonable estimates of properties of liquid metals can be made. Indium is particularly well-suited to investigation, since it remains liquid over a long temperature interval, it alloys readily, suitable containers for it are easily procured, and relatively few investigations of its thermodynamic properties in the region above 1000°K have been made. PREVIOUS RESEARCH The first determination of the vapor pressure of indium was made by Anderson,' using the Knudsen method and silica-lines stainless-steel cells. Kohlmeyer and spandau2 determined the normal boiling point, and a mass-spectroscopic investigation has been made by Lyubimov and Lyubitov.3 (Unfortunately, only an equation representing the data of the latter investigators has been available to us.) Hultgren et al.4 and Gurvich5 have published discordant tables of the free-energy functions for indium. EXPERIMENTAL METHOD The torsion-effusion principle has been described amply in the literature.8,7 With this method, one observes the angular deflection induced by effusion of vapor from a multihole effusion cell which is suspended from a filament producing a small rotational restoring force. The pressure within the effusion cell can be computed from the relation ziaifiai where k is the torsion constant of the filament, 6 is the observed angular deflection, and ai, fi, and qi are the area, force factor, and moment arm of the ith effusion orifice. The force factor f is analogous to the Clausing factor,' and corrects for the reduction in effusive force attributable to the finite geometry of the effusion orifice. Schultz and Searcy' have tabulated the force factors for various tube geometries. EXPERIMENTAL APPARATUS The physical arrangement employed in this study is shown in Fig. 1. The furnace elements are six Globar heat rods with 15-in. hot zones. Temperature is maintained to * 1°K by a Beck mechanism driving two 26-amp Powerstats in parallel. A Pt (Pt, Rh 10 pct) thermocouple serves as the sensing element. Four inner tubes act as vibration isolators; the air pressure required for maximum isolation was determined empirically, and is maintained by a solenoid valve. The tungsten fiber, 9 by 0.002 in., is joined to an 0.008-in. tungsten wire or graphite rod via a machined lightweight chuck.

Jan 1, 1964

The Mateen deposit comprises two large spodumene-bearing pegmatite dikes that outcrop along the, side and crest of a hill overlooking 'Rill City in the southern Black Hills of South Dakota. The Bureau of Mines investigated the Mateen deposit as part of a comprehensive study of the lithium mineral-production possibilities in the Black Hills area. The work was undertaken during the second World War, when the demand for certain lithium salts and compounds exceeded the small productive capacity of the industry. During the course of the investigation, the Bureau of Mines took 61 large channel samples from surface trenches, 4 channel samples from a shaft, and 3 from the face of an open cut. In addition, 8 diamond core-drill holes were completed to investigate the attitude of one of the dikes at depth. Metallurgical tests were conducted by the Bureau of Mines to determine the feasibility of beneficiating spodumene-bearing ores from the Mateen dikes.

Jan 1, 1948

By G. A. Savanick

The Bureau of Mines has designed, fabricated, and field tested a water jet cutting device capable of perforating nonmetallic well casings for the purpose of completing or stimulating in situ uranium leaching wells. The device is lowered into the wellbore, where it issues a high-velocity water jet that penetrates either a polyvinyl chloride or fiberglass casing, cement, and from 1 to 4 feet into the surrounding uraniferous sandstone. The resulting perforations allow leaching solution to pass between the sandstone and the wellbore. This report describes the water jet perforator, tells how it is used, presents cost data, and discusses the results of laboratory and field tests. The tests were designed to (1) determine the optimum operating conditions for water jet perforation, (2) assess the effects of changes in these conditions, (3) evaluate the performance of the water jet perforator under actual conditions, and (4) compare this method with other methods of well completion. These tests showed that water jet perforation is superior to conventional well completion methods for selectively achieving communication between the well-bore and adjacent sand while maintaining sand control, for restoring permeability lost through wellbore damage, for stimulating poorly performing wells for completing wells with casings that have inside diameters as small as 2 inches, and for extending the effective well diameter.

Jan 1, 1981

By E. Ozberk

The copper and nickel smelting industries are important contributors to the technical and economic well-being of Canada while some of the smelters are among the largest sources of sulphur dioxide emissions in Canada. A review of the operations in six smelters - Falconbridge Limited, Falconbridge, Ontario; Hudson Bay Mining and Smelting Co. Limited, Flin Flon, Manitoba; Inco Limited, Copper Cliff, Ontario and Thompson, Manitoba; Noranda Mines Limited, Horne Division, Noranda, Quebec and Gaspe Mines Division, Murdochville, Quebec - have shown that about 80% of the total sulphur input to these smelters was emitted to the atmosphere in 1980. A simultaneous review of the existing and emerging technologies which can directly or indirectly reduce the sulphur dioxide emissions indicated that it is possible to reduce the emissions to below 20% of the sulphur input to these smelters. This can be achieved by varying degrees of modifications to the smelting operations and installing sulphur fixation facilities at significant costs which may increase the metal production costs. This would consequently make the competitiveness of the Canadian copper and nickel producers more difficult in the already tough world metals market.

Jan 1, 1983

By B. C. Craft

Oil and gas development in Mississippi during the year 1933 was rather active and a number of important wildcat wells were drilled throughout the state. Mississippi showed an increase in drilling operations during 1933. There were 58 completions from 22 counties during this period, compared with 53 completions in 10 counties during 1932. The Jackson gas field in Hinds and Rankin counties continued to be the most active area with 26 completions, resulting in 17 gas wells, 2 oil wells, and 7 dry holes, compared with 38 gas wells, 1 oil well and 5 dry holes during 1932. A further attempt to extend the producing limits of the Amory gas field resulted in a dry hole. Extensive exploration in south Mississippi has proved the existence of ample source beds and presence of an extensive sandbody near the top of Cockfield. Core tests, supplemented by extensive geophysical work, have been carried on in Jackson, George, Harrison, Pearl River and Stone counties. Exploration will be continued in 1934. The most important deep test drilled in 1933, and the deepest well ever drilled in a southeastern state, was the Eastman Gardner et al., Bank of Seminary No. 1, sec. 26-8N.-15W., Covington County. This well went through about 1300 ft. of Selma chalk, and was abandoned in the Eutaw at 8004 ft. Another interesting operation during the past year was the Foster Creek Oil Corporation's Foster Creek Lumber Co. No. 1, sec. 14-2N.-2W., in the "Eastern Conroe Trend." This test is shut down at 3687 ft. in the Catahoula sandstone and has not encountered any important shows of oil or gas. A total of 107 of the 117 gas wells completed in the Jackson gas field since its discovery in 1930 are still producing, and have a combined open flow of approximately 3,724,896,000 cu. ft. It is reasonable to assume that this area will be rather inactive during 1934 as the maximum daily production during 1933 was 3,476,000 cu. ft. The 10 wells that have gone dead were edge wells. The water level is now between the sub-sea depths of 2190 and 2195 ft. The Gulf Refining Company's Rainey No. 1, sec. 13-5N.-lE., one of the early wells in the field, had gas and water at —2225 ft. That the field is under hydraulic control is

Jan 1, 1934

By R. C. A. Thurston

INTRODUCTION THE deleterious effect of stress raisers or notches on the resistance to fatigue of machine components, and other parts subjected to repeated dynamic loading, has been well known for many years. Most engineers in the mechanical field have, at one time or another, encountered a shaft which fractured due to a poor transition fillet, a holding-down bolt which failed due to insufficient tightening or inferior thread form, or a fitted member which broke through a combination of fretting corrosion and clamping stresses. All of these are examples of the damaging influence exerted by stress raisers in fatigue. Other common forms of stress raiser which have taken their toll of dynamic components are: keyways, oil holes, splines, quenching oil grinding cracks, tool marks, and sharp changes in section; some are the result of the design, others of poor execution of the design. It is our experience in the Mines Branch1 and I feel sure this will be corroborated by other fatigue investigators, that the majority of failures are due to incorrect design or faulty preparation of the part concerned, rather than to the use of inferior material. Quite frequently, it is true that the operating conditions necessitate the presence of a 'notch', but even in such cases methods are generally available by which its adverse effect on the life of the component can be reduced or annulled. The purpose of this paper is to discuss a few typical stress raisers, and to provide information on various processes for mitigating their effects in fatigue.

Jan 1, 1951