Search Documents

By D. J. Hawk

The mechanical properties of coal are often represented by the orthotropicmaterial model, which consists of nine elastic constants. The material symmetries involved are found in coal primarily because of the natural process by which it was formed. In this thesis the material properties of five U.S. coals, as obtained from cubical testing, are examined, using as a basis for comparison the assumption of the orthotropic material model. An analysis is performed on each set of coal material data in order to examine its conformability to other, less complex material models, these being the transversely isotropic model consisting of five elastic constants and the 'isotropic model consisting of two elastic constants. In addition, the material properties of two American shales are analyzed, based on the assumption that they comply with the transversely isotropic model. An analysis similar to that performed on the coal material is applied to the shale in order to determine the conformity of its material properties to the isotropic model.

Jan 1, 1980

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

By George J. Young

(San Francisco meeting, October, 1911.) THE nature of slimes handled in the treatment of gold- and silver-ores has been discussed in technical literature to a considerable extent. The subject of slime-filtration from the practical worker's stand-point has also received much comment, and scattered through the literature of the subject are descriptions of many slime-filtration installations. Articles of this nature serve a valuable purpose and assist materially in the design of new and the improvement of old plants. The subject of the physics of slime-filtration has been touched upon to only a slight extent. The underlying principles are worthy of more intensive study and experimentation than they have received, and the main purpose of this paper is to present the results of such study and experimental work as will serve to make clear in part at least many of the principles which control the filtration of slime. Nature of Slime. Much has bean written concerning an accurate definition of the term ? slime," but no comprehensive definition seems to be generally accepted. The reason for this is clear. A slime consists of at least three different substances, each, when separated, possessing distinctly different physical and to a certain extent chemical properties. These substances are extremely fine sand, a colloidal material which may be and generally is in a coagulated condition, and a colloidal material which is in a non-coagulated condition. Suspending a slime in a relatively large volume of water by shaking and allowing sedimentation to take place, results in the fine sand settling out with comparative rapidity, followed by the coagulated material, which settles much more slowly and finally a certain portion remains

Nov 1, 1911

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By Ulrich Neumann

Mining coal by employing a method called longwall mining is gaining more and more popularity in the United states since it offers many advantages over the conventional deep mining methods. Those advantages are a higher productivity, an almost total extraction of the mineral since no pillars must be left behind for support, and an increase in safety since the personnel are protected by the shield supports and rarely have to work near unsupported, exposed root. However, on some longwalls, the dust levels liberated by various equipment such as belt conveyors, chain conveyors, crushers, longwall shearers, and moving shield supports can exceed the maximum permissible limits and therefore have an adverse effect on productivity. Many attempts have been made over the past years to reduce the dust liberation by changing designs, installing various types of sprays or scrubbers, treating the mine water with wetting agents, or even using foam to catch dust before it becomes airborne. In the year 1984, the Bureau of Mines awarded Eickhoff Corporation a contract to demonstrate a water-jet-assisted cutting system for the multiple purposes of reducing dust levels, improving bit consumption, and increasing material size. During the previous phases of this contract, various trials were conducted aimed to design, build, and test d shearer loader to meet the objective of the contract. In the early stages of the research program, it was expected to see a reduction in the overall power consumption of the machine due to the fact that the high-pressure water jet would pre-cut the mineral in front of the bit. This, in turn, would then reduce the bit wear. Since there is less cutting action performed by the bit, a reduction of the dust liberation and a reduction of product fines was sought.

Jan 1, 1991

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By B Gyngell, P Culvenor

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organisations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyse the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Sep 1, 2024

By Herbert K. Kutter

This paper is concerned with the physical phenomena in the fracture process of presplitting and only indirectly with the establishment of the optimum presplitting parameters. Its nature is therefore qualitative, rather than quantitative.

Jan 1, 1968

By R. M. Creamer

Attempts have been made to electroplate titanium and zirconium from aqueous, nonaqueous, and fused-salt electrolytes. Metals were produced only in fused-salt electrolytes, the major product being sponge metal. All other electrolytes gave only partial reduction of the metal ions. Fused alkali borate electrolytes containing titanium salts gave titanium boride powders and coatings of poor adherence. Some of the problems encountered in the deposition of these metals and some of the aspects of titanium and zirconium chemistry involved are discussed. INTRODUCTION Titanium and zirconium are both relatively light, noncorrosive metals with both military and civilian uses. This has led to intensive investigations into the metallurgy of these metals. Both metals are high in the Electrochemical Displacement Series and are difficult to prepare in a pure state. At present they are prepared by reducing their chlorides, using magnesium. Electrolytic reductions have resulted in the preparation of fine powders or sponge of variable quality. It is believed that a good process of electroplating these metals on a baser metal would result in a very desirable product. The objective of the research summarized in this report was to investigate methods of electrodepositing these metals, with the idea of producing uniform, coherent plates. Most of the work was concentrated on titanium, the more abundant of the two metals. A system developed for titanium should be applicable to zirconium owing to their chemical similarity. Information gained from these experiments may also be applicable to the electro-winning of the metal.

Jan 1, 1954

By G. B. Gait

This report is the third in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of mines in the Lackawanna Basin of tile Northern anthracite field is presented. Previous reports IC 8274, published in 1965, and IC 8379, published in 1968, were catalogs of microfilmed maps of mines in the Eastern Middle anthracite field and Wyoming Basin, Northern anthracite field, respectively , Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1970

By B. Seegmiller, W. A. Hustrulid, O. Stephansson

Introduction The concept of in-the-wall haulage was formally introduced to the mining community in the early 1970s. The basic concept is simple. Rather than the traditional in-the-pit haulage/access ramp, single or twin ramps driven in the pit wall are used with crosscut connections on the working levels. The in-the-wall pit haulage system could be considered as part of the opening of a new mine, a way of completing to final depth an existing pit, or part of the transition from open-pit to underground mining with the ramp remaining as part of the access. This paper is intended to acquaint the reader, particularly mine planning engineers, with some of the possibilities presented by the concept. Nordstrom (1983) said, "In many countries, mining engineers are either open-pit or underground specialists and, hence, often don't consider the possibilities for combining the best aspects of each into a hybrid mining system." This is believed to be true. There are few "hybrid mines" employing, for example, open-pit methods with underground haulage systems. One reason is the variance with the experience of the mining company and the engineers involved. However, with today's low metal prices, innovative and unconventional thinking may be just what a property requires to remain in production. All the possible situations where an in-the-wall ramp might be considered cannot be presented here. Rather, a few examples will be discussed for illustration purposes. Potential savings in stripping costs A major cost in open-pit mining is associated with the removal of overburden and waste rock. Although much of this stripping cannot be avoided, the volume (V) associated with the presence of an in-pit haul road can be quite large, V 100 (pit depth) a (road width) 2 x road grade (%) As an example, consider a vertical ore body 400 m (1312 ft) long, 60 m (197 ft) thick, extending to a depth of 160 m (525 ft). Cross sections are shown in Fig. 1. Other data are: ore tonnage = 11 Mt (12 million st), ore density = 2.9 t/m3 (0.09 st per cu ft), waste rock density = 2.7 t/m3 (0.08 st per cu ft), road width = 20 m (66 ft), road gradient = 10%, and level interval = 10 m (33 ft). The evaluation has been made assuming that the pit slope (0) is constant around the pit except on the side with the haul road. On this side, the slope is decreased to allow for the road. Slope angles of 30° to 60° have been selected to indicate the dependence of stripping volume (V) on slope angle. The stripping at the ends have been calculated assuming representation by cones. The volume associated with the haul road is 2.6 Mm3 (92.8 million cu ft). A comparison of the strip volumes involved is shown in Table 1. As can be seen, the percent savings in strip volume varies from about 4% to 17% and depends greatly on the slope angle. It is perhaps more interesting to examine the savings in stripping costs that could then be used to cover the cost of the access ramp and the crosscuts for stripping costs of $3/m3 ($0.08 per cu ft). The cost with the road volume is 2.6 million x 3 = $7.8 million.

Jan 1, 1988

By S. W. Cavender

The analysis of the results of metallurgical experiments is often complicated by experimental errors and uncertainty, the complexity of the system being studied, and the confusion of correlation with causation. Consequently, comparative statistics are used to determine if a difference exists between the outcomes of tests, an estimate of this difference, and the precision of the estimate. This paper reviews the use of significance tests and confidence intervals for the comparison of results from two tests, the use of reference distributions, and blocking and randomization techniques to reduce unavoidable sources of variability. These techniques are demonstrated using plant and laboratory data.

Jan 1, 1993

By Jonas Svensson

The Grangcold Pellet Process - for which patents have been applied or already granted in a number of countries - uses a hydraulic adhesive such as Portland cement, slag cements, pozzolanic cements, etc., for the production of cold bonded pellets. The idea of using a hydraulic binder for the agglomeration of iron ore fines is not new. Portland cement was proposed as an adhesive for cold bonded iron ore briquettes in patents granted more than 50 years ago (1). In a report on the briquetting of iron ore fines, published in Stahl and Eisen 1959 (2), it is stated that briquettes bonded with Portland cement are used on a small scale at on ironwork in Germany. According to the report, the briquettes showed excellent strength in the blast furnace although their general use was made impossible because they required a long hardening time, during which they are sticky, soft and difficult to store and handle. The Grangcold Pellet "recess has overcome this particular disadvantage by mixing the balls with a suitable amount of the balling concentrate before storing them. The pellets are embedded in the concentrate during storing in such a way that they are isolated from each other and thus prevented from sticking together to form clusters. Thanks to the embedding concentrate, the pellets are subjected to a more or less uniform pressure from all sides which does not deform them. Thus the mixture can he stored in a stockpile or in a silo until the pellets have hardened sufficiently. The concentrate is separated from the pellets by means of screening. The concentrate is returned to the balling operation and the pellets are either shipped to the blast furnace or stored for final hardening.

Jan 1, 1969

By L Lorenzen

The selection of samples for metallurgical test work is generally focused on providing geologically representative samples. One of the major problems experienced with metallurgical test work using drill hole data, is the small sample sets selected for metallurgical testing. Major process and financial decisions are being made from results obtained using snapshot samples. Snapshot samples means that samples are basically selected only by grade and spatial location with the assumption that the rest of the orebody or portion of orebody is similar and will respond metallurgically the same way – ie the assumption is that the mineralogy and lithology are basically the same as the test sample. From the test work, algorithms were usually developed and used to describe throughput and recovery using some explanatory variables including grade (mineral chemistry) and ore hardness. These algorithms were then used in the recovery models to determine tonnes produced and plant throughput. However, the metallurgical parameters are a function of many geological factors including grade, lithology, alteration, mineralogy, spatial relationships and SG. In previous years, the limited mineralogical information available was deemed enough for the metallurgist to make decisions as to how many samples are needed to evaluate the metallurgical performance of the ore during processing, and subsequently the basis for the plant design. If the orebody is consistent and not complex or refractory (thus, relative simple lithology), then only spatial and grade samples will be needed to evaluate the throughput and recovery, so limited mineralogical information may be acceptable. There is now, however, an increasing realisation that the mineralogy and geology change, as do the metallurgical characteristics of the orebody, so limited samples may not be sufficient for effective metallurgical test work.It is the purpose of this paper to discuss the effect correct mineralogical information has on the subsequent metallurgical test work program and process selection using a case study. Factors such as type of rock, rainfall and topography are thought to influence the minerals that ultimately form in various orebodies, with the result that different orebodies often react differently during metallurgical test work programs. It is therefore important to obtain accurate mineralogical and elemental deportment data, which will also indicate where the valuable metal containing minerals are located within the orebody. The better you plan and execute your metallurgical test work program during the early phases, the more accurate the decision-making process will be during the selection phase. Improved integration between geology and metallurgy data gathering (geometallurgy) during early phases will result in more accurate predictions with regard to throughput and recovery during modelling and process. Equipment selection will be considerably simpler in later phases with early planning, with improved mine and process scheduling and subsequent net present value (NPV).

Sep 5, 2011

IN this paper an attempt is made to describe the sluicing operations on the tin fields of north-eastern Tasmania. No claim is made to completeness, for much of the ground has already been covered, and nothing is to be gained by needless repetition. On this account some portions of the subject have obviously received but scanty attention in order that others may be rather more fully dealt with; for instance, figures referring to the accuracy of various methods of valuing alluvial deposits, particulars of efficiencies, and water duties on both overburden and drift; also, the system of recording water distribution, &c.The plans of the tin-streaming shed, sluice and feed·race, and overburden tail-race represent types of the most modern design.The principal alluvial deposits being worked at the present time are situated either in the ancient or modern bed of the Ringarooma river or its tributaries. This river flowed in a north-easterly direction, receiving numerous tributaries on either bank, and finally emptying into Boobyalla harbour. The most important of these tributaries, from a mining point of view, are the Cascade, Main creek, Weld and Frome rivers (which unite just before joining the modern Ringarooma), Wyniford river, and Bradshaw's...

Jan 1, 1911

Throughout the study phases (scoping, prefeasibility and feasibility) of new mining projects one is forced to work with and make predictions based upon limited date obtained from diamond and reverse circulation drill holes. These data are extrapolated to determine how much of the valuable metal is present in the ground, how it can be recovered it and the efficiency of this recovery. Mining methods to extract the ore are investigated with forecasts made regarding excavation stoping stability and performance in an attempt to optimise production. Extraction and use of rock mass data for use in characterising the mechanical behaviour of the rock mass is no exception. One often relies heavily upon the use of empirical charts developed over many years on hundreds of case histories based upon rock mass characterisation schemes. This is largely successful and indicative of what one might expect. However specific site characteristics can always play a significant role, and are not necessarily apparent in diamond drill core. Feasibility studies for the Favona orebodies indicated that the rock mass was generally poor to extremely poor, and that stoping conditions would be difficult in all of the orebodies for various reasons. A range stope performances were achieved ranging from very good to very poor and in some cases unexpected results were achieved. A comparison is made between what was actually achieved and what was expected since stoping commenced in 2007. Explanations are attempted for differences in stoping performance and, in some cases, unexpected results at the Favona underground mine are attempted.

Nov 25, 2010

By Ethan Steward, Kyle Perry

Underground coal mines have several dangers, one the most hazardous of which is the possibility of an explosion caused by the ignition of methane gas. To reduce ventilation costs, coal mines have the option to close off abandoned areas that are no longer active with structural seals to keep an explosion from propagating into working areas of the mine. These seals must be designed to withstand different pressure levels based on the potential of the atmosphere behind the seal to become explosive, either 50 psi (345 kPa) for inert atmospheres, 120 psi (827 kPa) for non-inert, and over 120 psi (827 kPa) for special cases. Though seals have been designed to resist the overpressure, none have been evaluated for their resistance to the impact of heavy objects. Underground explosions produce high velocity gasses that, traveling through mine openings, may propel objects in the mine at a high velocity causing them to impact and damage the mine seals. Seals damaged in this manner may no longer hold the pressure they were originally rated for and may fail during subsequent explosions or leak explosive gasses into active workings. To test the effects of impact on mine seals, a projectile generator and two seals have been constructed. The projectile generator is a 12-inch (30.5 cm) inner diameter steel pipe with a 4-inch (10 cm) wall, is 8.5 feet (2.6 m) in length, and sealed on one end. Projectiles are propelled by a charge of black powder with a wooden wad and are held in place by foam sabots in the bore. This system, combined with the large bore, allows firing of many different potential projectiles that may be found in an underground mine at a high velocity into the seals. The velocity of each projectile is measured by an infrared chronometer which can later be used to determine its impact energy. Impact effects on the seals are measured using strain gauges, LIDAR scans before and after impact, high speed cameras, and visual inspection. The focus of this paper is on the projectile generator design and initial testing.

By B. A. Slaker

The ability to detect and quantify ground movements in underground mine workings is of the utmost importance to the safety of miners and continuity of operations. Rib sloughage is one of the most common forms of underground deformation. Remote sensing techniques, such as laser scanning, can be used to quantify this rib sloughage, by recording precise, timelapse point clouds of mine workings. In order to determine sloughage volumes and locations, two sets of laser scans were performed 42 days apart at a working section of an underground limestone mine. During this period, significant sloughing and scaling occurred, allowing for differentiation between the initial and final point clouds. Volumetric changes of 2.3-2.6 m3 were detected on rib faces during the time-lapse study. In addition, displacement in the mine roof was, as expected, not detected, suggesting well surveyed scans and an appropriate scan resolution.

Nov 1, 2013

By A. E. Gooch

The Bureau of Mines conducted research in an attempt to provide a more sound basis for recommending improved artificial support during deepening of the main shaft of the Lucky Friday mine in the Coeur d'Alene mining district of northern Idaho. Field measurements of closure across the short axis of the 13-by 26-foot shaft were as high as 16 inches. Elastic/plastic finite-element (F/E) analyses were made, reducing the values of large-scale in situ rock mass properties until field closure measurements generally corresponded to displacements in the F/E analyses. Resulting plots of rock mass displacements, stresses, and areas of plastic failure display the results of creating openings (shaft, in this case) in deep mines in difficult ground conditions requiring artificial support.

Jan 1, 1976

By S. S. Pathak, S. Mishra, M. H. Tyeb, A. K. Majumder

Roping in hydrocyclones is a well-known phenomenon in mining and mineral industries which put serious restrictions on their continuous and maintenance free operation. Roping is mostly observed in association with high underflow solid concentrations which can be attributed to higher fraction of solids reporting to the underflow or the feed solid concentration itself being higher. This paper proposes a newly designed spigot with a truncated conical geometry which can allow for a rope-free discharge at higher feed solid concentrations. The experimental observations revealed that in the operation of a 50.8-mm-diameter hydrocyclone, roping ensued at 10% to 12.5% (wt%) feed solid concentration depending on feed inlet pressure for the cylindrical spigot, whereas with the modified spigot, rope free discharge was attained even at 25% (wt%) feed solid concentration.

Jan 8, 2022