Search Documents

By A. G. Weber, R. L. Ledbetter, A. L. Hicks

A procedure which makes use of both analog and digital computers has been developed for predicting the pressure-production behavior. of water-drive reservoirs. The electric analyzer is used for matching the past pressure and production history of the reservoir and inferring the physical characteristies of the aquifer. When the history has been matched, a .set of base curves called influence functionce" are derived and the future behavior of the reservoir is calculated from these curves. INTRODUCTION Electric analog methods are particularly well-suited for complex water-drive problems. Like all other methods of analyzing water-drive reservoirs, however, analog methods are subject to certain limitations. One of the more obvious and serious of these results from inaccurate or insufficient knowledge about physical characteristics of the reservoir and aquifer. However, it is not insurmountable because the unknown characteristics can usually be inferred from the reservoir's previous behavior. Simons and Spain have shown that even with scant reservoir data and limited production history, electric analyzer studies can provide useful and reliable results. Aside from this limitation on analyzer predictions, the main disadvantage has been lack of a technique for keeping predictions abreast of latest production forecasts. Pressure behavior of a reservoir depends on the rate at which fluid is withdrawn; it is therefore necessary to specify the future withdrawal schedule before the future pressure behavior can be calculated. Conventionally, the electric analyzer predicts pressure behavior for a specific production schedule. If this schedule is abandoned in favor of some new one, as is frequently the case, either the study must be rerun or results adjusted in some manner. The usual procedure is to predict pressures for several different forecasts covering a wide range of production rates. Pressures for specific rates other than those studied can then be approximated by interpolating between the analyzer predicted curves. However, reliability of this type of prediction is doubtful. This paper describes a technique for predicting future behavior of water-drive reservoirs that retains all advantages of electric analyzer analysis and eliminates the main disadvantage. That is, the analyzer is used conventionally to infer unknown reservoir parameters from the pressure history, but not to predict the future behavior directly. Instead, a derived set of base curves, called influence l'unctions, can be used to calculate future behavior for any production schedule.

By I. W. L. Finlay, H. R. Ogden, R. Jaffee, D. J. Maykuth

Aluminum has been found to be soluble in a titanium to about 26 pct, and to raise the temperature range of transformation from a to 8. Two intermediate phoses exist in the system, a new face-centered tetragonal phase, designated as 7, which occurs between 34 and 46 pct Al, and TiAI Metallographic and X-ray diffraction data were used to determine the diagram. ALUMINUM is one of the useful alloying additions for titanium-base alloys. It is an important constituent in two commercial alloys released in 1950, one containing 4 pct A1 and 4 pct Mn, and the other containing 3 pct A1 and 5 pct Cr as the metallic alloy content. It is probable that, in the future, other titanium alloys containing aluminum will be released. In the course of alloy development work, some of the features of the constitution of titanium-rich Ti-A1 alloys have been developed. These are described in the present paper. The only available information on the Ti-A1 system concerns the aluminum-rich end of the diagram. In summarizing the early work, Hansen' indicated that there is little solubility of titanium in aluminum, and that a two-phase region exists up to the intermediate compound, TiA1a (37.2 wt pct Ti), which has a congruent melting point at 1355°C. Fink' has reported that a peritectic reaction occurs at 665°C between the melt and TiA1³ to form the terminal solid solution of titanium in aluminum. The solubility of titanium in aluminum has been established at 0.24 pct at 510°C and is estimated to be between 1 and 1.5 pct at the peritectic temperature. No information has been published on the diagram above TiAl,, other than a statement- hat aluminum raises the a to ß transformation temperature of titanium. Materials and Preparation of Alloys Iodide-type titanium and high-purity aluminum were used in this investigation. Typical analyses of these materials are given in Table 1. Alloys were prepared by arc melting on a water-cooled copper hearth, using the techniques described previously for contamination-free melting.' Weight losses during melting were very low, ranging from 0 to 0.02 g in a 10 to 15 g charge, indicating that little or no loss of aluminum occurred during melting. This permitted the use of nominal compositions for these alloys. Alloy ingots containing from 0 to 7.5 pct A1 were rolled in air at 850°C to 0.040 in. sheet. Alloys containing from 7.5 to 16 pct A1 could only be rolled about 25 pct reduction at temperatures up to and including 1200°C. Alloys containing above 16 pct A1

Jan 1, 1952

By K. Purazrang, P. Musavi Garavi, P. Sh. Naseri, P. Abachi

The fracture behavior of high strength Al7050 alloy was investigated at room and elevated temperatures using small size, V-notched tear (called Kahn specimen) and compact tension, CT, specimens, respectively.To study the elastic-plastic behavior of the alloy, the tensile test was also performed on the sub-sized cylindrical tension test specimen. The microstructure of the alloy was examined using optical- and scanning electron- microscopy. The rupture mechanisms and crack path were also studied by examination of specimens' fracture surfaces using SEM. The microstructure examination revealed equiaxed grains and some elongated grains in rolling direction, with the areas of partial re-crystallized grains where coarse intermetallic particles are mostly found.In general, fracture surfaces were indicative of dimpled ductile type. Considering the fractographs of tensile specimens, the void growth mechanism is also dominant in fracture of these specimens. Nevertheless, in some regions, smooth areas can be observed due to the friction during rupture process. The results of mechanical tests at RT made the evaluation of tear strength to 0.2 % tensile yield strength ratio, as a measure of notch toughness, available. According to elevated temperature, 150°C, test results and plots of log da/dt vs. log KI , the crack propagation behavior over discrete ranges of crack growth rates could be assumed linear and then be obeyed as a power law equation in the form of da/dt = A (KI)n .

Jan 1, 2015

By N. S. Dalal, Xianglin Shi

"The mechanism of vanadium(V) V ) toxicity is still not fully understood in spite of extensive current effort (1-3). The presence of a vanadium(V) V ) -dependent NAD ( P )H oxidase in cell membranes suggests that at least one of the pathways involves oxidation of NAD(P)H (1-3). Considerable effort has therefore been devoted to finding the mechanism of NAD ( P ) H-oxidation by va¬nadium( V ) (1-19). Recently Liochev and Fridovich (4, 16) provided a critical review of vanadium( V) -stimulated NAD (P )H oxidation by plasma membranes. They out¬lined a mechanism in which vanadium(V) V )-stimulated oxidation of NAD ( P )H by biomembranes involves an O2 - initiated free radical chain reaction (4 ). While the above may be the major pathway for the vanadium-me¬diated NAD (P )H oxidation in membrane-related sys¬tems, some recent results suggest that in the presence of NADPH the flavoenzyme glutathione reductase can function as a vanadium(V) V ) reductase (18). Because of the significance of this result in relationship to the mech¬anism of vanadium( V) metabolism and the novelty of the metal-reductase behavior of a flavoenzyme, we have car¬ried out additional studies on one-electron reduction of vanadium( V) by two other, related flavoenzymes: lipoyl dehydrogenase and ferredoxin-NADPH oxidoreductase. These two enzymes were selected because they are known to catalyze a one-electron reduction of Cr ( VI ) (19-21 ), which is isoelectronic with vanadium( V ).The present study also reports on the generation of hydroxyl ( • OH) radicals in the vanadium( V) -flavoen-zyme redox system without exogenous H2O2. The • OH study was undertaken because • OH radicals are known to be generated in reactions of vanadium( IV) with H2O2 (17,18,22-27). For example, Piette and co-workers (17, 22) have studied effects of vanadium(IV) IV ) on lipid per-oxidation and NADPH oxidation and suggested that va-nadium( IV) -induced • OH radical formation may play an important role in vanadium( V) toxicity. Carmichael (25, 26) investigated the reaction between a RNA /VO 2' complex and H2O2 with a view to probe the possible re-lationship between vanadium( IV) -mediated • OH radical generation and DNA damage. He has suggested that in this reaction the • OH radical adds to the C (5) carbon of uracil, causing nucleotide damage, similar to what occurs in the nucleotide /Fe2+ / H2O2 reaction (28) and in y-irradiated aqueous solutions of nucleic acids (29 ). To our knowledge, however, there is as yet no report on ·OH radical generation in any reaction involving the reduction of vanadium ( V) by a well-characterized enzyme, without exogenous H20 2 • The present study provides evidence that ·OH radicals can form in a flavoenzyme-mediated reduction of vanadium( V) to vanadium( IV) and that this process involves also the reduction of molecular oxygen ( 0 2 ) to H20 2 • The H20 2 thus generated reacts with vanadium( IV) to produce ·OH radical, in analogy with the Fenton reaction ( Fe2 + + H20 2 - Fe3 + + OH- + ·OH)."

Mar 1, 1992

By Renato G. Bautista

The solvent extraction separation of nickel, cobalt and their associated metals have been considered for industrial application since the early 1960's. This review of the solvent extraction processes is limited to the industrial applications, pilot plant and the more extensive bench scale studies reported in the literature. The processes with their significant chemical and technological contributions are discussed in detail whenever the information are available. The application of solvent extraction to the nickel-cobalt processing has so far been limited to the secondary separation of nickel-cobalt containing feedstocks derived from other primary nickel-cobalt separation methods.

Jan 1, 1993

By Engelmann. William H.

In pursuit of innovative methods to improve mining productivity, the Bureau of Mines is investigating the use of inorganic salts as drilling fluid additives for penetration enhancement. Laboratory diamond drilling tests were performed on Westerly Granite with aluminum chloride solutions and on Sioux Quartzite with aluminum nitrate and aluminum, calcium, sodium, and zirconium chloride solutions as drilling fluid additives. These drilling results were compared with the average drilling performance using distilled, deionized water on Sioux Quartzite (12 replicate tests) and Westerly Granite (3 replicate tests). Maximum in-creases in penetration per given time and bit life were obtained when drilling with zero point of charge (ZPC) concentration solutions of each additive. For Sioux Quartzite, maximum increases in penetration and bit life ranged from 96 to 115 pct and 64 to 99 pct, respectively. For Westerly Granite, maximum increases in penetration of 155 and 165 pct and bit life of 109 and 136 pct were obtained at or near ZPC aluminum chloride concentrations of quartz (7.3 x 10-7 mol/L AIC13) and alkali feldspars (1.1 to 1.5 x 10-6 mol/L AIC13), respectively. This simultaneous increase in penetration per time together with extended bit life should result in increased productivity and reduced bit costs.

Jan 1, 1987

By D. Harrington

The Bureau of Mines was created in 1910 largely to determine methods of preventing coal-mine explosions; the Bureau's studies have proved that coal dust, except possibly that of some grates of anthracite, can initiate an explosion in the absence of gas and that its ability to extend or propagate an explosion of either gas or dust has been responsible for nearly all of the widespread explosions that have taken place in bituminous and other nonanthracite mines in the United States in the present century. It is believed by many persons that all atmospheric dusts may be harmful if breathed in large enough quantities for long enough time; bituminous coal dust is generally considered to be essentially harmless physiologically, yet there is abundant evidence of definite damage from inhalation of bituminous dust mixed or unmixed with the dust of other materials. Attention un¬questionably should be given to allaying dust in bituminous mines, especially at principal dust-producing sources. This publication enumerates some of the sources of dust and describes practical methods of employing water as one of the most effective of the known methods to allay dust in bituminous mines.

Jan 1, 1938

The realization that there is a limit to our supply of domestic mineral and fuel resources, which have been taken for granted until recently, has stimulated the need for conservation and optimum utilization of the Nation's minerals, metals, and fuels-resources critical to our national economy. The mission of the Bureau of Mines is to develop new technology, improve existing technology, and disseminate information related to mineral resources and industries. Fulfilling the mission is necessary to insure a continuing, adequate supply of minerals and alternative supplies of energy from reliable sources at the lowest possible cost to society and the environment. Established in 1910, the Bureau of Mines under the Department of the Interior is the Federal Government's primary research arm in the mineral field. Since the transfer of the fossil fuels portion of the energy research program to the newly organized Energy Research and Development Administration (ERDA) in fiscal year 1975, Bureau research has been concentrated on increasing mineral production, decreasing energy usage through more efficient processing, and decreasing material losses caused by corrosion. Concurrently, research is being addressed to improved coal-preparation techniques, especially to expanding utilization of low-grade coals and coals difficult to beneficiate, which are essential for reducing the need for petroleum and natural gas supplies and for redirecting our energy consumption. Fluctuations in the availability of foreign sources of minerals, metals, and fuels due to political and economic variability among nations have necessitated intensified investigation into coal mining, uranium-ore processing, and geothermal energy sources-three alternatives that can help to alleviate the dependence of the United States on foreign sources of energy.

Jan 1, 1975

By Thomas Novak, Sampurna Arya

Controlling dust generation and keeping it below permissible limits to meet federal dust standards at the working face of a roomand-pillar coal mine is a challenge for a mine operator. With the recent changes in federal dust regulations requiring lower worker exposure, maintaining compliance has become increasingly difficult. The current most effective practice of dust control at a continuous miner face in an underground mine is the use of a flooded-bed scrubber. A study carried out by the National Institute for Occupational Safety and Health (NIOSH) indicated that a flooded-bed scrubber could achieve cleaning efficiencies between 58 and 90%. But, the operation of such a system is maintenance intensive. The flooded-bed scrubber screen becomes clogged with dust particles and requires frequent cleaning to maintain performance. However, the dust control issue is not solely a mining industry problem. Other industries face similar issues. The University of Kentucky collaborated with Toyota Motor Manufacturing on the development of a novel wet scrubber, called the vortecone scrubber, for capturing oversprayed paint particles in automotive paint booths. The vortecone scrubber achieved a cleaning efficiency of 99% and required minimal maintenance. This study aims to assess the ability of this vortecone scrubber to capture respirable dust in an underground coal mine. The paper presents the results of computational fluid dynamics (CFD) modeling of this vortecone scrubber. It discusses the effects of air quantity and dust particle size on the performance of the scrubber.

By N. Waters

"Nickel saprolite ores are normally mined as feed to Fe-Ni smelters or Ni matte smelting operations. The smelting processes typically require high Ni cut-off grades of approximately 1.5 to 2.2% Ni, depending on the operation. These very high cut-off grades result in a significant portion of the saprolite profile being regarded as “waste” and hence having little to no value. The Starved Acid Leach Technology (SALT) was developed to recover nickel and cobalt from nickel saprolites and Caron plant residues. Relatively small amounts of acid are applied to ground saprolites or Caron residues in order to selectively leach nickel and cobalt. The leaching is performed atmospherically under low free acid conditions. Nickel and cobalt may be recovered from the leachate as a mixed hydroxide. The mixed hydroxide may be added directly to a saprolite smelting operation or refined separately. InCoR Technologies is advancing the application of SALT at a number of sites. Bench scale testing has provided a relationship between acid addition and nickel extraction in leaching. Conceptual engineering studies have been completed by SNC Lavalin. The simplicity of the SALT technology provides the benefits of low capital and operating cost and an expected rapid ramp up to full production.INTRODUCTION The recent history of hydrometallurgical nickel laterite treatment plants has demonstrated mixed financial and operational performance. Table 1 summarizes the next generation plants built after the financial and/or technical failure of the Bulong, Cawse and Murrin-Murrin plants in Australia. The Coral Bay plants (Line 1 and 2) stand out (and now Taganito) as relatively low capital cost, simple (no acid plant, production of mixed sulfide product), and modest in scale (10, 12 and 36 kt Ni/a). However, the other plants in the list (Ravensthorpe, Ramu, Goro and Ambatovy) are all characterized by financial and technical challenges. All plants have a very high capital cost ($67,000 to $120,000 USD/annual t of Ni production). Ravensthorpe was sold by BHP Billiton after a poor startup. Ramu has had a steady ramp up but only produces mixed hydroxide for refining by others. Goro has had an extended construction period (since 2001), is high cost and has been very slow to ramp up to design production rates. Ambatovy has had a steady ramp up."

Jan 1, 2017

By Mostafa Maazouz, Jeff Blackwood, Mauricio Gordillo, Sang Hoon Lee, Micah Ledoux, Liang Zhang

To meet rising requirements for the low-damage ultra-fine process with the focused ion beam (FIB) in the materials science and semiconductor industry, the advanced ion column and corresponding advanced applications as a solution are developed and demonstrated. Novel high-speed high kV milling, low kV cleaning and imaging capabilities have enabled the creation of impeccable ultra-thin structures such as TEM samples and nanometer scale structures. Minimizing Ga+ induced sample damage is achieved through the optimized final cleaning at 500 eV ion landing energy with the new ion optics, which utilizes close control of the ion dose, beam incidence angle, spot size, pattern algorithm and imaging performance. Newly introduced process solutions achieve the improved process throughput. Initial demonstration is performed on the latest 14 and 10 nm scale FinFET device. Validation of the thinnest <0.8 nm thick ion damage layer on the <7 nm thick lamella structure was confirmed through TEM analysis.

Mar 1, 2017

By A. C. Dorenfeld

In most mineral enterprises, what is the progress, and shift in responsibilities, as the young engineer advances in the corporation? You are all familiar with the normal pattern-in mine production from level boss, to shift boss, to superintendent to manager; in milling from test engineer, to shift boss, to foreman, to superintendent and then manager; in engineering from surveying on to Chief Engineer; and all then aspire to the corporation presidency. Note the shift-from purely technical jobs, say in the first five to ten years in the profession, to administrative positions for 30 to 40 years. What is the average preparation given to mineral engineering students, who can look forward to about 30 years of administrative work? From the catalogs of 21 institutions, offering 36 curricula of four years length, in mining and/or metallurgy, requiring the equivalent of about 150 to 160 semesterhours for graduation, the following results were obtained: Average number of semester hours of economics, 3 hr. Range of requirements, 0 to 8 hr. Thirteen curricula do not require any economics. Accounting and business law, average: 1 semester hr, 26 curricula do not require business law or accounting.

Jan 2, 1955

By R. G. Knickerbocker, C. T. Baroch, A. W. HACKWOOD

The difficulties inherent in the production of alumina by the formation of potassium alum and its subsequent thermal dehydration and decomposition have been overcome , to a large extent , in a process developed at the Boulder City Station of the Bureau of Mines . This process is applicable to the reserves of alunite known to occur in several Western States and , possibly , to certain clay and low-grade bauxite deposits known to exist in this country . The operations sequence of the process is shown in the flow sheet (fig . 1) . Only those steps included within the heavy line are considered in this report . Four different procedures for dehydration of alum were investigated ; ( 1 ) Spray drying , ( 2 ) rotary - kiln drying , ( 3 ) dry grinding in a thermal ball mill , and ( 4 ) dehydration in the vertical- column flash dehydrator . Based upon fuel requirements and other practical considerations , the vertical- column dehydrator , or some modification of its operating principle , offers the botter possibility for commercial use .

Feb 1, 1946

By H. M. Smith

The production of oil during the early development of new oil fields is usually accompanied by large quantities of natural gas. Since in most fields gas under pressure is the main source of the energy causing the oil to move through the sands into the wells and thence to the surface, coincident production of natural gas will continue as long as present-day producing methods are used. Generally the use of this gas is restricted, since markets are not readily available. Consequently, a large portion of the gas produced is often wasted by being blown into the air. The magnitude of gas waste is well brought out in the following statement by Miller:5 Only a few outstanding examples need be cited to show the enormous production of gas that accompanies the discovery of new sources. In April, 1927, the Ventura field produced approximately 210,000,000 cubic feet of gas a day; and during the summer of 1927 Alamitos Heights reached a peak gas production of 102,000,000 cubic feet a day; on December 1, 1928, as a result of the summer&apos;s deeper drilling in the Long Beach field, surplus gas production amounted to 125,000,000 cubic feet a day. It is estimated that in January, 1929, the Santa Fe Springs field will have a daily gas production of 387,000,000 cubic feet from the recently discovered Buckbee oil zone. Of this amount 274,000,000 cubic feet a day will be the surplus above the amount required for field and plant fuel, taken out by utility corporations, and that used in repressuring the Meyer sand which lies above the Buckbee zone.

Jan 1, 1931

By MáAndrusiewicz, M M. Hilden, M S. Powell, P D. Kay, B Foggiatto

Circuits with unconventional and potentially more complex designs are predicted to become more common in the future as plant designers and operators look to process ores more efficiently. Ideas have been presented on how circuit design may be changed to utilise todayÆs technology to address tomorrowÆs challenges (Powell and Bye, 2009; Powell, Benzer and Mainza, 2011a). High pressure grinding roll (HPGR) installations in various configurations; application of preconcentration plants eg sorting, magnetic or gravity separation; and preweakening devices eg microwave processing; are all examples of technologies having the potential to deliver a significant reduction in comminution energy for ores amenable to these processes. Not only will future novel circuits contain equipment for which models are not as well developed (if at all), many will likely require the ability to respond to variations in feed, and interact with geometallurgical models requiring process adjustments when the ore characteristics change.In order to confidently simulate more complex circuits and accommodate variations in feed type, a significant advancement in modelling and simulation capability is required. This includes dealing with multiple components in the feed, accommodating different competencies of ore, utilising physical separation opportunities and tracking the grade reporting along the different potential processing routes. Developing the means to simulate complex circuits has been a key priority of a collaborative group of comminution researchers working to solve these challenges.Simulations are presented utilising a new configurable simulation interface called the model developers kit (MDK). The MDK is designed to accommodate multi-components and incorporate new models under development. These will be used to demonstrate the potential of flexible circuit design, based on measured ore properties and equipment performance.CITATION:Foggiatto, B, Hilden, M M, Powell, M S, Kay, P D and Andrusiewicz, M, 2012. Simulation of flexible circuits, in Proceedings 11th AusIMM Mill OperatorsÆ Conference, pp 291-298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 29, 2012

By A Teen

An open cast mine on the West Coast of the South Island of New Zealand proposes to remove up to 30 m of overburden to access an ore body neighbouring National Reserve land. Part of the conditions of the mining permit is that no material above natural discharge levels may be released over the Mining Lease boundary onto the adjacent land. In order to meet this requirement, the client has contracted the design and installation of over 2.6 km of high energy dynamic rockfall control barriers. This paper describes how the rockfall hazards were assessed and the rockfall barriers dimensioned. The design involved 2D modelling of over 3000 simulations. &nbsp; Modelling parameters were calibrated during field trials at a purpose built section of barrier. The resultant energies ranged from 500 to 3000 kJ. The construction phase of the project involved the drilling, anchoring, and installation of certified barriers up to 7 m high in a remote and inhospitable climate with limited machinery access. By exploring best practice in this specialized field of engineering, a novel rockfall hazard mitigation solution was identified.

Jan 1, 2007

By P B. Hills, R J. Walton

Geotechnical instrumentation has been implemented as a key step for monitoring and optimising an engineered mine design for managing seismicity at the Beaconsfield Gold Mine. Measurements of displacement, stress change, ground control element load and seismic response of the rock mass allow for back analysis and calibration of critical parameters for feedback into the engineering design loop. Instrument clusters are installed in strategic locations prior to the commencement of stoping in order to determine the nature of the response of the rock mass to stoping. A selection of instruments including instrumented cable bolts and rod extensometers, resistance wire extensometers, hollow inclusion stress cells, vibrating wire stress meters and resistance wire extensometers are used to gather data through a data logging system. The rate at which data is recorded is adjusted to provide more information during periods of anticipated rapid change such as around stope firings or during periods of high seismic activity, and less information during periods of anticipated quiescence. The twofold purpose of the instrumentation is to calibrate the numerical modelling output which forms the basis of the engineered mine design, and to provide an alert mechanism where the behaviour of the rock mass is not what was anticipated, or where the impact of that behaviour may compromise the integrity of the engineered ground control system. The paper describes the location of instrument clusters with respect to stoping, the type of instruments employed and the method of data acquisition. It provides examples of results obtained and illustrates the way in which that information is used to optimise the mine design and manage seismicity.

Jan 1, 2008

[JOSEPHSON, W. G.: The Argonaut Mine of Today, M88, 475 JOUET, C. H., biography, M29, 258 Joule-Thompson effect, 98, 381 JOWETT, J. H., biography, M83, 276 JUDSON, S. A.: Operations in the Gulf Coast of Texas and Louisiana for 1926, G26, 659 JUDSON, S. A., EASTON, H. D. JR. AND SCHAEFFER. W. A. JR.: Estimation of Petroleum Reserves in Prorated Fields 114, 11. Abs., YB35, 50 JULIHN, C. E.: Copper---An Example of Advancing Technology and the Utilization of Low-grade Ores. Brookings Lecture, in Mineral Economics (1931 volume, B. W. Mudd Fund)]

Jan 1, 1936

By Edward E. Johnson

The Bureau of &apos;Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By H. L. Bridgman

The correct sampling of ores is a subject of far greater importance than is usually conceded to it. Of the little which has been published on this subject, the recent paper by Mr. Glenn, with the accompanying discussion by Dr. Raymond (Trans., xx., 155), is the latest and best, and well worthy the careful perusal of all interested in accurate sampling, whether by hand or by machine. It is doubtless true that thorough hand-sampling gives as good average results as can be obtained; but all hand-sampling is subject to the possible incompetency, carelessness, or dishonesty of the workmen employed. It is, moreover, tedious and expensive, requires large space, and usually entails considerable delay, both in unloading and in sampling. For these and other reasons, machine-sampling is now regarded with more favor than ever before. So-called machine-sampling may be accomplished in two radically different ways: 1. Part of the stream of material is taken for the whole time. 2. The whole stream of material is taken for part of the time. Under the first case the stream, as it issrles from the deliveryspout of the crusher, is cut continuously in any given proportion, such as one-tenth, one-fourth, or one-half, by some fixed apparatus, which, as it contains no moving parts, is strictly speaking not a machine at all, but may be termed an appliance. The principle under which these appliances operate is now pretty generally conceded to be wrong, becanse of the practical impossibility of&apos; cutting such a

Jan 1, 1892