Search Documents

By C. M. McCulloch

A geologic study of Mines 32 and 33 in Cambria County, Pa., was conducted as part of a methane control research program. Areas of high methane emission and roof instability are encountered which are related to the structural and stratigraphic features that characterize the geologic setting of these mines. Locally the folds trend N 20° E ±2°, the direction of the butt cleat in the Lower Kittanning coal. The face cleat strikes at N 69° W ±2° and the systematic rock joint in the surface bedrock strikes N 67° W ±2°. This suggests that a directional stress oriented N 70° W produced the folds and influenced the directions of coal cleat and systematic joint sets. Analysis of SLAR indicates three directions of prominent regional lineation: N 39° E, N 31° W, and N 70° W. Little gas was encountered during development mining; large volumes of gas are encountered when roof falls. Most of the gas comes from strata above the mined coal; therefore, to control methane, roof instability must be controlled. Roof falls and high rates of methane emission are most likely where less than 30 feet of many thin layers of limestone, shale, and sandstone occurs between the Lower Kittanning coal and the next coal and in zones along the margins of a sandstone channel.

Jan 1, 1973

By G. W. Josephson

WHILE methods of utilizing blast-furnace slag have been developing, a great deal of literature on the subject has accumulated, but no comprehensive summary of information that would be helpful to engineers, contractors, architects, chemists, and others in under-standing and more successfully using this byproduct of the iron and steel industry has been published in the English language. The National Slag Association recognized the need for such a publication, and the Problems Committee of the Association under-took in 1943 to accumulate the necessary material. Over a period of several years this committee compiled pertinent information in manuscript form, and in 1948 the Bureau of Mines and the National Slag Association made an agreement whereby the Bureau was to prepare the data for publication as a cooperative bulletin of the Bureau of Mines and the National Slag Association.

Jan 1, 1949

By M. Cohen, P. E. Beaubien, D. Caplan

Addition of 1 pct Mn to Fe-26 CY ca/(ses a12 increase in scaling rate at 870° and 1090°C. Whereas only the rhombohedral oxide, formrs on tire manganese-free alloy, with manganese present major amounts of the spinel .Mn0 . Pro-duced through which diffusion is more rapid. At 1090°C the scale formed OH Mn is highly, irregular due to blistering and sintering, This is a second cause of faster oxidation Since much of the blistered oxide does not participate as part of the protective layer. The oxide phases that form at different times depend on the degree to which the surface metal has become depleted, in manganese by preferential oxidation. PREVIOUS work has demonstrated that the oxide scales formed on chromium steels at high temperature consist of both spinel and rhombohedra1 phases and may contain considerably more manganese, especially in the spinel phase, than is present initially in the alloy.' It has further been observed that a binary Fe-26 Cr alloy scaled less rapidly than an equivalent commercial steel and formed no spinel.' However, it is not established if manganese in chromium alloys actually promotes formation of spinel nor if it affects oxidation resistance. It seemed expedient to try to evaluate the specific effect of manganese by oxidizing an Fe-26 Cr alloy containing a small manganese addition under the same experimental conditions as used for the manganese-free alloy.' EXPERIMENTAL Table I shows the composition in weight percent of the Fe-26 Cr-1 Mn alloy and of the Fe-26 Cr alloy used as reference. The alloy with manganese was prepared from the vacuum-melted Fe-26 Cr alloy by remelting in vacuum with the proper manganese addition. The ingot was rolled to strip and specimens 1.1 by 0.035 by 5 cm and 1.1 by 0.5 by 4 cm cut out or machined. As previously described2 the specimens were smoothed by abrading through 600-grit Sic paper, electropolished in acetic-perchloric acid (20 to 1) to remove 10 p of metal, annealed at 1100°C in 20 torr of purified argon, and electropolished to remove a further 10 p of metal. They were then either rinsed in water and methanol and blotted dry or immediately etched for 45 sec in deoxy-genated 4 N HC1 under cathodic polarization at 10 pa per sq cm. Oxidation runs were carried out in a vertical tube furnace in a flow of purified oxygen at 1 atm while the weight increase was recorded continuously on a* automatic balance.3 Alter 98 hr at 870.C or 20 hr at 1090"C the specimens were removed to flowing argon and observed microscopically for evidence of spalling as they cooled. Subsequently they were examined by X-ray diffraction, the oxides analyzed chemically, and metallographic cross settions prepared. RESULTS Figs. 1 and 2 show the oxidation curves of Fe-26 Cr-1 Mn at 870' and 1090C. The Fe-26 Cr reference runs are shown as dashed curves. Experimental details of the six runs are included in Table 11. The first 20 hr of run 1 is repeated in Fig. 2 to show the effect of temperature. At 8'70°C the weight gain for Fe-Cr-Mn is about twice that of Fe-Cr (curve 1 vs curve 2, Fig. 1). Both alloys show regular oxidation curves. On parabolic coordinates (right-hand scale of Fig. 1) the

Jan 1, 1965

By Charles Will Wright

The present struggle for economic and industrial supremacy by the Communist world is against the United States, its main target, and the other Free World nations. The basis of industrial power is minerals, so the Communist nations are building up mineral production within their borders, often regardless of costs, and are acquiring quantities of mineral products from Free World countries for future use. They are contracting for additional supplies and advancing funds for the development of these quantities. A number of the less developed mineral producing countries of the Free World are being infiltrated by Communists and Communistic influence. This situation is well known, but as yet little has been done to oppose these activities or to awaken the public to their seriousness. The Communist countries are still far behind the Free World Nations in production of many essential minerals. But, shortages are being made up from Free World nations in exchange for petroleum, manganese ore, chromite and other products. Restrictions on shipments of strategic materials to Communist countries have not been maintained.

Jan 1, 1964

By Evelynn Stirling

Agenda ? Emissions legislation ? Cummins Tier 4 Technology ? Cummins Experience with Technology ? Operation and Maintenance Impact The Emissions Challenge ? The 2014/5 emissions regulations present the most significant challenge to our customer?s diesel powered equipment design and operation in recent history? ? ?and Cummins has the solution.

Aug 1, 2013

By G G. Suffel

T HESE remarks on the occurrence of strata-bound massive sulphide deposits are submitted be-cause the writer recently visited the principal Cyprus deposits (in January, 1965) and has also a back-ground of many years spent largely in detailed observation and map-ping of the Horne and Amulet ore-bodies, now largely inaccessible. They are particularly related to the Symposium papers (September Bulletin) by Hutchinson and by Roscoe. Some comments are offered on the cupriferous pyrite deposits of Cyprus. As the writer is currently reviewing the published literature on the related deposits in Turkey, a brief account of some characteristic Anatolian sulphide occurrences is given. The discussion is closed with some thoughts on the relationship between these Mediterranean sulphide deposits and those of northwestern Quebec and the Superior province in general. The geology of Cyprus, as it relates to the sulphide deposits, is well summarized by Hutchinson (1965). After visiting Mavrovouni, Skouriotissa and Limni and after much thought on the possible ge-nesis of these ores, it seems quite logical to me that he is right. They are indeed closely related to late-stage submarine volcanism.

Jan 1, 1965

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

Invensys’ recently introduced Field Device Manager for Foxboro I/A Series distributed control systems provides the industry’s first solution that takes advantage of both the latest Enhanced Electronic Device Description Language (Enhanced EDDL) and FDT technologies. This combination provides comprehensive lifecycle support to configure, calibrate, commission, diagnose and optimize the performance of any vendors’ foundation fieldbus device. The I/A Series Field Device Manager enables users to take advantage of any EDDL, Enhanced EDDL and/or FDT host deliverables supplied by the device vendor.

Jan 1, 2007

By Robert L. Lagace

[Suuple Iheorctrccil models are I'M lllolalcd to cltaraclerl/c medium frequency (MF) radio vase pi opaiation in undcrgiounli room arid pillar coal mines fur the purpose of predleiln the most lavolable operating fIegtucncics,md nr,ixunum communic;IIIoil ranges for pottahIe rldu)s with I top antennas. I or conductul IrCC areas, at hree layer propaeaIion IltodcI wit II a Iiallsmissloil IIIIi- lhlllllIIal'u11 lot the plupa!edti ii unlstallt Iris been dcvcloped ;md verified experimentally. 1 lie mode u1 propaCaUetl lakes Ills form of i parallel plane (0,t)) TIM lransnussu)nhne 1% PC of mode with the electric held vertical and the magnetic held hoti/cntal t itliin a planar coal scam in which the tunnels Can he ignored and which 1s hounded above and below hp richer conductivity rock. 1lie model lilt the data best river the 200 io 1000 kH/ frequency hand and exhibits a rc;;lon of optlnrul1l Pelffelntance, with respect Io maxnluiulg radio Communication range, between 300 and 100 klf/. Maximum cunununlcatrorl ranges are sliongls dependent oil the sigiial alleilliatroil sale, ant) Illelclulc on the electrical conductivltles of the coal seam and surrounding ruck. These ranges v;ny tutu about ,,5 Io 100 nleleis Ill a high Iuss scam such as the Ilelllit No. fl to about .100 to 400 meters in a low loss seam such as the Pittsburgh foil portable intrinsically safe radios. The ieslllls die haled on the comparison oftheorc' and experiment for eleven n n. ill sesen coal seams. V OT ate is dice: a conductor such as a power Cable, is present a model has been developed for the coupling of loop antennas to a low loss Coaxial TEM ti;u?smisslon line mode in which the cable acts as the inner conducl,lr and the rock above and below acts as the outer conductor. The electuc and md' nctic Itelds for till` (node are apprlixitllatcly transverse to the cahlC and fall oil expontially with distance in the transverse plane. The principle of reciprocity is used to simplify the analysis. More expelitnental data arc needed to help resolve discrepancies between the theory and the limited data available to date.]

Jan 1, 1980

By Leonard Weixler, Peter Halbach, Michael Jarowinsky, Johannes Post

Germany as an industrial nation is highly dependent on the import of mineral or metal resources. Sources which have not been considered until now are the marine mineral resources (MMR), which in recent times are enjoying more and more increasing interests and which might provide in the future a considerable contribution to the supply security on metal resources not only for the industrial countries. Backed up by the German government’s "National Masterplan Maritime Technologies" (NMMT) and corresponding industrial R&D-activities, the idea and the advantages of deep-sea mining is gaining more and more interests and supporters with respect to industrial and political considerations on strategic raw material resources as well as on the development of deep-sea mining technologies. The NMMT aims to initiate growth and increase the competitiveness of the German maritime industry on international markets and covers about 10 different marine and ocean technology sectors including deep-sea mining.

Sep 1, 2014

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By P. Nicholls

Though the burning of fuels extends far back into antiquity, and though fuel beds are the most common and widely distributed example of chemical actions and engineering practice, there has been little attempt to group fuel beds by types or to define the principles associated with them. This paper does not profess to cover completely the subject of fuel beds. It suggests some of the over-all principles of the two more common types. No new investigational data are included, but the deductions are largely based on a recent publication of the U.S. Bureau of Mines'. Definition of Types There are three primary types of fuel beds: (I) Underfeed, in which the fuel and the air move in the same direction; (2) overfeed, in which the fuel and the air move in opposite directions; (3) crossfeed, in which the fuel and the air move at right angles to each other. The principle that fixes the type is the relation between directions of the flow of fuel and of air. Fig. 1 shows the three types diagrammatically. All other types are compounded of these three in a simple or more or less complex manner. It does not follow that these three type designations are limited to the methods used in representing them in Fig. 1; they may be turned in any direction, and as long as the relative directions of the fuel and air are the same the type is not changed. For example, A as shown .resembles a pot-type stoker, but the air and fuel can move downward as in the so-called smokeless heating boiler furnace. Also, C can be placed horizontal, as in chain-grate stokers. For this reason, the terms used to designate the three types are not all that could be desired; more logical ones could be coined, but those used probably are satisfactory until the discussion of fuel-bed types becomes more common.

Jan 1, 1936

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By Allan E. Koski

Ceveland-Cliffs uses a specialized software package in mine planning at the Empire Mine, an iron ore mine it manages on Michigan’s Marquette Iron Range. The application puts together years of mining experience that began in the early 1960s on the eastern end of the Marquette Range. The Empire Mine is in its 38th year of production. It uses the software to model a complex and highly variable low-grade magnetite ore body, capturing the economics of mining and processing to the final product. With special attention given to geostatistical methods, the software is used for all geologic modeling, ore reserve estimation, ore control, pit design and short- and long-range planning.

Jan 1, 2000

By James L. Ash

This report contains the results of a technical and economic evaluation of conceptual systems for the underground mining, rubblization, and in situ retorting of deep oil shale deposits. Study efforts were first directed towards evaluation of the applicable geology, associated minerals, rock mechanics, in situ retorting, access mining, ventilation, rubblization, safety, and environmental impact factors. Conceptual systems were synthesized and then evaluated against these factors from both a technical and limited economic viewpoint. The results of these evaluations were then analyzed and, based upon this analysis, the following two systems were selected for further study: System II: Room and Pillar-Vertical Drill and Blast System IV: Tunnel Boring-Horizontal Ring Drill and Blast Due to the large number of variables to be considered, a computer program was developed and utilized to provide data for the cost trade-off studies and economic analysis. Results of the early computer runs indicated the value of the tool available? in the computer program and led to an extension in the contract to determine the sensitivity of the systems to several of the more apparent significant variables. These results in turn led to a refinement in the design assumptions and a better understanding of the technical and economic options available to an owner-operator of a Vertical Modified In Situ Shale Oil Extraction System. This report is submitted in fulfillment of the requirements of Contract Number 50241073 by Fenix & Scisson, Inc. to the Denver Mining Research Center, United States Department of the Interior, Bureau of Mines. Work was completed as of November, 1976.

Jan 1, 1976

By S Sims, A Stradl, G Hope, B Lacouture

Column flotation cells have been installed in numerous base metal operations around the world. The majority of these cells utilise conventional air-only spargers to introduce air into the bottom of the column. The recent development of instruments to measure the bubble characteristics in these columns has provided a renewed understanding of column behaviour. These new tools provided insight into why the columns at Red Dog Mine had never performed up to expectations. After efforts to optimise the spargers failed to substantially change the bubble size and air efficiency, alternate sparger systems were investigated. The Metso Minerals CISA Microcel sparger system appeared promising and was selected for a full-scale plant trial. The Microcel sparger system was originally developed for the coal industry at the Virginia Centre for Coal and Minerals Processing. In October 2003, a Microcel was retrofitted into one of two 3.66 m diameter flotation columns in the zinc retreat circuit at Red Dog Mine. The operation of the two different sparger systems in parallel allowed a detailed comparison. This paper discusses the performance of the Microcel based on the data collected during several detailed surveys. Bubble size measurements carried out in the pulp zone using the McGill University bubble viewer showed a significant difference in bubble size. The mean Sauter diameter of the bubbles decreased from 3.4 mm for the jetting-type sparger to 1.9 mm for the Microcel sparger. The overall recovery and the recovery by size fraction for both valuable and gangue minerals were compared. Paired t-tests demonstrated that the Microcel column produced a higher concentrate grade (0.6 per cent zinc absolute) and a higher unit recovery (2.8 per cent zinc absolute) than the existing Canadian Process Technologies Inc (CPT) SlamJet column. These improvements provided a payback period of 1.5 months for the $109 000 investment.

Jan 1, 2005

By A. E. Hilder

Introductory The following pages present the results of field investigations, laboratory and commercial tests, drilling, surveying, and preliminary development of the refractory clays which have been discovered recently in the township of Kipling, at the foot of Long rapids on the west side of the Mattagami river about 57 miles north of Kapuskasing and approximately 7 miles north of Smoky Falls, the terminus of the privately owned railway operated by the Spruce Falls Power and Paper Company, Kapuskasing (see Figure 1). Investigations on the clays of northern Ontario have been carried on over a period of seven years by officers of the Ontario Department of Mines, and I am indebted to the information published by that Department in reports by W. S. Dyer and A. R. Crozier, as well as?by Professor R. J. Montgomery, of the Ceramic Department, University of Toronto. It was, in large measure, the data given in the 37th, 38th, and 42nd Annual Reports of the Ontario Department of Mines that led me to make a personal investigation of the Mattagami River clays, with the result that we now have a commercial undertaking that will develop eventually into an industry of considerable importance in supplying the central manufacturing districts of Canada with refractories that heretofore have been largely imported from the United States. An extract from the 42nd Annual Report of the Department, Part III, 1933, page 75, reads as follows: "As for the refractory clay, the deposits are undoubtedly very large, but what is urgently needed is a deposit near the railway under sufficiently shallow overburden for recovery by stripping'. Having previously made an investigation of the clays adjacent to the Temiskaming and Northern Ontario railway, and these clays proving unsuitable, I turned my attention to the outcrops of refractory clays on the Mattagami river, first reported by Keele in 1919. This area offered possibilities within the economically permissible distance from rail transportation.

Jan 1, 1935

By W. P. Johnstone

The computer assisted generation of geological models to represent the geometry of, and grade distribution within, orebodies is a rapidly growing area of the geological profession. Such models are increasingly used as a necessary starting point in determining the mineability of mineral deposits in terms of practical mine design and economic considerations. The transition from traditional techniques such as field or underground mapping and the manual calculation of grade and tonnage estimates, as well as related activities such as the interpolation of cross-sections, the use of stereographic projections, core logging and hand contouring, to computerized applications, is by no means complete. In fact, many geological professionals deliberately avoid the use of computer simulations based on the perception that the resulting models are simplistic and that their construction is not founded on sound geological principles. The purpose of this paper is to assess current thinking on this topic by considering; (a) an overview of advances in the drafting of geological maps, (b) the theoretical basis for multi-dimensional geological modelling, (c) the case for combining traditional and modern techniques, and (d) the benefits to the mining value chain.

Jan 1, 2003

By W. Chi, R. Regan, R. A. Washington

"In uranium mines, the purification of underground mine air can be accomplished by the removal of dust particles and radon daughters using filters. Full-scale statistically designed experiments with flow rates up to 10,000 cfm have been conducted at Denison Mines Ltd. on mine air filtration with vermiculite as a filter material. Various filtration bed thicknesses were chosen, with different face velocities through each bed thickness. Results on total dust, respirable dust and radon daughter collection efficiencies were analysed statistically. It is shown that these collection efficiencies are directly related to the filter bed thickness. However, the different face velocities seem to affect only the collection of radon daughters. Optimum collection efficiencies for a clean bed of about 30% were found for respirable dust and radon daughters, and about 41>% for total dust, using an 8-in.-thick bed and a face velocity of 500 fpm. Dust build-up on the filter bed during operation led to an increase in collection efficiency, reaching 40 to 60% after two weeks."

Jan 1, 1973

By C. J. Allen, L. Battiston

"Introduction It has long been recognized by the hot-dip galvanizing industry that the characteristics of the galvanized coating can be influenced significantly by steel and pro cessing variables. Probably the variable of most concern to galvan izers today is steel chemistry. More specifically, the problem is the excessive reactivity of continuously-cast, silicon-bearing steels. In the past, structural steels processed by general galvanizers were in the low-to-medium ca rbon category and contained silicon at either low impurity levels (as with rimmed steels), or less than approximately 0.10% (as with semi-killed steels). The structures of the coatings produced on such steels are characterized by dense, compact layers of delta and zeta iron-zinc alloy phases and a distinct outer layer of eta zinc, which usually imparts a bright shiny appearance to the coating. The presence of silicon in steel, above the so-called semi-killed levels, is known to cause marked stru ctural changes in galvanized coatings. Such coatings are characterized by a relatively thin delta layer, a thick , coarse zeta layer and frequently an absence of the eta layer. The eta phase, comprising zinc which is carried out of the bath during withdrawal of the work, can be consumed by the continuation of the coating reactions until its temperature drops to the solidification point. This results in a dull grey and often mottled surface instead of the usually bright metallic appearance. These galvanized coatings are usually much thicker than coating specifications requ ire and they are usually more brittle and have poor adhesion to the steel. In service, these coatings tend to develop a rust-like discolouration. With the wider use of continuous casting by the steel producers and the associated additions of silicon in this process, the problem is becoming more important and receiving greater attention from the galvanizing industry ."

Jan 1, 1987