Search Documents

By S Januszewski and, G Dirom, D Christensen

Four field test plots were constructed in 1998 on a sloped waste rock surface at the Myra Falls Operations of Boliden Westmin (Canada) Limited to evaluate hydraulic performance of alternate cover system designs. The field test plot cover systems were designed to control oxygen ingress and water infiltration to the underlying waste rock while providing a medium for a grass and legume vegetation cover. The test plots consisted of a bare waste rock surface (control plot), and three additional plots consisting of native compacted till placed directly on the waste rock surface, overlain by non-compacted till. Two of the test plots included a compacted till layer ameliorated with flyash and bentonite, respectively, to improve moisture retention and reduce permeability. The third test plot consisted of a compacted layer of native till overlain by non-compacted till. A performance monitoring system was installed in each test plot to evaluate net percolation and oxygen ingress to the underlying waste rock. In addition, each test plot has profiles of matric suction, water content, and temperature sensors installed at up-slope and down slope locations. A review of four years of monitoring data shows that the compacted till/bentonite cover system has been most successful in limiting the infiltration of meteoric waters and oxygen ingress to the underlying waste rock material. The compacted till/flyash and compacted till cover systems have produced similar net percolation results and neither have functioned well in maintaining an oxygen ingress layer throughout the year. The amelioration of bentonite with till to produce a compacted barrier layer shows promise in reducing water and oxygen ingress at the MFO site, while the incorporation of flyash with the till did not result in a significant increase in performance. The field performance data clearly demonstrates the need for developing field trials prior to full-scale construction, as opposed to relying solely on an un-calibrated numerical modelling to design the full-scale cover system.

Jan 1, 2003

By Willie M. NeSmith

In the Metropolitan Atlanta Area today, augered, cast-in-place (ACIP) piles will be considered on most projects where deep foundation support is required. ACIP piles were first used in Atlanta in the late 1960s, and application began to blossom in the mid-1980s. Current design practice for ACIP piles is addressed in another paper in this conference. This paper describes the evolution of the ACIP industry in Atlanta, and details the use of ACIP piles on major projects in the Atlanta area.

Jan 1, 2003

The Malvern Hills coal project is now in an advanced stage of development with the stripping of overburden from above former underground workings in which a 3 m seam of subbituminous C coal with very low ash and sulphur was previously mined. The main seam dips at 45¦ to the south-east, along with other adjacent potentially recoverable thinner seams, and the strike extent of past coal mining in the Malvern Hills approaches 10 km with most extraction by underground methods. Overburden and interburden is predominantly weak mudstone, with only very minor sandstone, whilst a 1 - 2 m thick veneer of Last Glaciation loess covers the area. The coal product from the present mine site will supply the local industrial market, with production planned to peak at about 20 000 tpa. Settling pond design has been based on several different approaches, including an estimate of likely inflows from the contributing catchment of about 5 ha under predicted storms having a ten year recurrence interval. A pond of about 1000 m2 in area has been constructed with its invert in mudstone bedrock, and soil slopes have been lined with lime-stabilised clayey loess silt incorporating a gravel armour layer. The pond outflow takes place via a 2 m high 1.8 m diameter concrete dewatering tower, with a skimmer arrangement to lower the pond by approximately 500 mm between storm events. The overflow water discharges to the main stream above a natural wetland, which will act as a secondary polishing pond, and this is to be enhanced in conjunction with the neighbouring forestry company. Discharge consents specify turbidity and pH as the controlling criteria, and both will be monitored at the settling pond discharge point as well as at the entry to the main stream. Investigations to date indicate that the pH of water exiting from previous underground workings is in the range 6.8 to 7.2, and that acidic drainage will not be an issue with this mine site. No dispersive clays have been identified in assessing the overburden and batter materials, although erosion during storm events is expected and all drains will ultimately be routed through the main settling pond to ensure adequate control of runoff-generated sediment. Reestablishment of vegetation on cut and fill batters remains a priority, and ongoing monitoring will ensure satisfactory long-term performance of the pond system.

Jan 1, 2003

By Joseph K. Cavey

To accommodate the new Pier A expansion at BWI airport, a 1.8 m (6.0 ft)diameter stormwater pipe was constructed below active Runway 15R-33L. The jacked tunnel alignment runs east/west below the runway, and the depth the crown was 6.1 m(20 ft). Soil conditions consisted of very loose to medium sand and gravel, with some medium stiff clay and silt. Super Jet Grouting was selected as the ground treatment system, creating large diameter columns. All work was performed from the surface of the runway between the hours of 12 am and 6 am. Monitoring points along the tunnel in the grout zone indicated zero settlement during tunneling. Tunneling operations in front of and beyond the treatment zone experienced significant settlement. Super Jet Grouting in the treatment zone provided a low permeability continuous stable soilcrete that was readily mined while the runway remained in service.

Jan 1, 2003

Anyone who has driven backwards using only their rear view mirrors knows how difficult it is to avoid spinning the steering wheel the wrong way. So why run your mine that way? Traditionally Reconciliation has focused on the past performance of the mine. In this paper we make a case for Prognostication û the act of forecasting or predicting something in the future from present indications or signs. Reconciliation is a common activity carried out at most mines around the world. Countless geologists and engineers spend hours poised in front of spreadsheets diligently comparing how their resource/reserve model, grade control, and survey pick ups compare to what was actually produced. The result is usually a group of factors, which are applied to future estimates in an attempt to better predict how the operation may perform. Unfortunately, if the road ahead isnÆt the same as what you have just been down, youÆll be æoff-roadingÆ in no time! An alternative is to constantly collect and analyse key measurements that are used to calibrate critical estimates in an iterative process. When variations occur, they are analysed and corrective action is taken to ensure the estimates and measurements realign. In this way the estimates become forecasts and can then form the basis for decision making to ensure that what does happen in the future will match the plan or schedule. By automating this process, some mines have been able to be proactive on a daily basis in order to improve the overall performance of the operation. This paper outlines the key estimates and measurements used for reconciliation, details the characteristics of an automated web based information management system to facilitate the process and provides some insights about how mining operations might move beyond reconciliation.

Jan 1, 2003

By M Vavro, V Slivka, J èterba

In the course of the last ten years the development of the mining industry in the Czech Republic has been influenced by the pushing through of economic and ecological criteria. Due to this coal mining was ended in the whole series of the underground coal mines. These mines become the source of ecological and safety risks û methane leakage, surface deformation, etc. The way of solving of these problems is by stowing of underground spaces, and also surface fault basins with the help of mixtures produced from industrial wastes. The presupposition of this procedure is knowledge of prescriptions for production of the mixtures, and of the economic advantageousness of carrying out these activities. This contribution pays attention to the utilisation of power-gypsum as a raw material in the production of mining-construction materials.

Jan 1, 2003

By Glenn Boyce, Paul Gribbon, Gary Irwin, Greg Colzani, Jim McDonald

This paper discusses the process utilized by the City of Portland Oregon’s Bureau of Environmental Services (BES) to procure and compensate Impregilo-SA Healy (I/H)for the West Side Willamette River Combined Sewer Over?ow (CSO) Project. The contract method is a three-phase process consisting of qualifications based contractor procurement, pre-construction phase design assistance/construction planning, and facility construction where the contractor is compensated on a cost reimbursable-fixed fee basis. The paper focuses on pre-construction phase lessons learned from the development of the contract general conditions, establishment of a construction budget and cost control program, incorporation of contractor recommended design changes, and development of a subcontractor procurement program for construction.

Jan 1, 2003

By J. Engesser

A research project was undertaken to determine if coal addition tofluxed-magnetite pre-fired pellets would reduce nitrogen oxide (NOx)emissions during pellet induration. Iron oxidation rate tests, coal oxidation rate tests and calcination rate tests were conducted in a laboratory furnace to determine the amount of coal necessary to provide adequate heat for limestone calcination without producing detrimental effects to magnetite oxidation. Pilot scale pot-grate tests were then performed with and without coal in the pre-fired pellets to verify pellet quality parameters and nitrogen oxide emissions. The off-gas during each pot-grate test was analyzed for NOx, CO2, CO, SOx, and O2. There was approximately a ten percent reduction in NOx emissions with coal addition during the normal pot-grate firing cycle. There was a 75% reduction in NOx emissions during firing cycles that used 25% to 75% excess air during firing rather than the normal 300% excess air.

Jan 1, 2003

By Daniel Kittelty

A fully instrumented laboratory electrowinning cell has been used to produce nickel cathodes from synthetic solutions containing various impurities in order to evaluate the effects of both metallic ions and organic reagents (from prior solvent extraction and other processes) on the quality of the electrodeposited nickel. The conditions used were typical of those employed in industrial electrowinning operations. The impurities were found to alter the crystal size and shape, induce the development of hydrogen pits on the deposit surface, incorporate as metal hydroxide crystals in the deposit, and alter the internal stress and current efficiency. These effects have been interpreted in terms of previously established relationships between the solution composition and the physical properties of the cathodes. The incorporation of the common metal impurity ions into the deposit have been interpreted in terms of a mass transport controlled reduction or precipitation reactions. In particular, a low concentration of aluminium ions resulted in an initial highly deleterious effect, which was replaced by a positive influence at higher concentrations. A model which involves the buffering effect of the aluminium on the pH at the cathode surface has been proposed.

Jan 1, 2003

By Ivan Imris

The iron production has generated many tonnes of very fine residues with high concentration of iron. In addition, during the recycling of galvanised steel scrap in the steel making processes the zinc and lead are largely concentrated in the dust. These kinds of dusts are usually dumped beside the metallurgical plants and cause environmental problems. Therefore the metal recovery from the metallurgical residues has become a major interest not only from the viewpoint of metals recycling but mainly from the viewpoint of environmental land protection. The thermodynamic analyses and laboratory experiments suggested that the metals could be recovered from metallurgical wastes by reduction roasting and by plasma smelting processes. The iron rich pellets with very high metallization may be obtained from metallurgical wastes by the reduction roasting and the inert slag and pig iron could be produced by plasma smelting processes. In both cases the iron rich products are suitable for the steel production. During the reduction roasting or plasma smelting the high volatile zinc and lead metals were removed and enriched as a secondary dust, Zn-Pb concentrate, which is suitable for processing in zinc and lead smelters. Suggested processes are commercially feasible and environmentally friendly without any solid or liquid waste.

Jan 1, 2003

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By T. R. Roy

"This paper presents an objective model for the estimation of fire risk potential of an underground coal mine panel by the bord-and-pillar method of mining where extraction is carried out by depillaring with caving. The fire risk rating procedure for the estimation of fire risk potential involved in the panel is described in detail. The model developed thereof is tested with the field data collected from different collieries across the country along with the laboratory data for critical assessment of fitness of the model. Some results showing the validity of the model are also cited here. Introduction The occurrence of fire in underground coal mine panels is quite common in India and elsewhere. These fires cause extensive loss of resources.Although substantial work has already been done by different research organizations, the problem has not been fully eliminated.The causes of panel fires depend not only on the spontaneous heating susceptibility of coal, but also on the extraneous conditions created in the panel due to the mining operations. From the studies done so far by various organizations, it is apparent that two types of parameters associated with spontaneous heating of a coal mine panel exist: intrinsic and extrinsic. Parameters related to the nature of coal, i.e., its physicochemical characteristics, petrographic distribution and mineral make-up are intrinsic, while the extrinsic parameters are related to the atmospheric, geological and mining conditions such as scope of leakage of air into the panel, wetness of mines, heat dissipation capacity of the panel, gassiness of seam, geological disturbances, method of extraction, size of panel, etc.Banerjee (1982) identified twenty-two mine parameters such as spontaneous heating susceptibility of coal, method of mining, geological disturbances, quality of overburden, degree of consolidation of coal mass, scope of accumulation of coal fines, etc. that can influence spontaneous heating in underground mines. He used the terms “high” and “low” for fire risk rating of each of these parameters. Since this approach is oversimplified, it can not determine the exact fire risk potential of an underground working."

Jan 1, 2003

By F. Terblanche, M. Holton, A. Kruger

The paper presents an optimal mine planning system designed to simultaneously optimize all the underground mines of large South African gold and platinum mining corporations. The system, code named PlanIT-OPTIM, is a multi-stage solution involving the use of adetailed 3D CAD-based mine planning system (CADSmine™V4). The mine design and scheduling rules defined in CADSmine™ are responsible for simulating mining sequencing, rock mechanics, and ventilation, etcetera. Feasible production ranges generated by CADSmine™ and various high-level mathematical models are used as inputs to a mathematical optimization engine. The optimization engine produces optimal production profiles (i.e. key business indicators such as tonnages, mineral and areas extracted per time period) by maximizing net present value. Other objectives such as profit continuity, production continuity and maintaining available reserves can also be specified as optimization criteria. The final step in the PlanIT-OPTIM process is to convert the optimal production profiles into practical and attainable business plans. This is achieved through the CADSmine™ Detail Optimization Engine that modifies the original CADSmine™ schedule to match the optimal production profiles. With current methods it is an impossible task to find the best business plan for a mining corporation in any reasonable period of time should conditions change (e.g. gold prices, exchangerates, grade estimates, etcetera). The fast turn around time achieved through PlanIT-OPTIM makes it possible to do several ‘what-if’ scenarios in a reasonably short time. PlanIT-OPTIM has already been used in the gold mining industry to find optimal business plans for a mine.

Jan 1, 2003

By M. S. Klima, A. Simard, M. L. Turek

Laboratory testing was carried out to evaluate several devices for recovering clean coal from bituminous coal refuse material. The bulk of the testing focused on using a dense-medium cyclone to process -0.6-mm refuse material. A hindered-settling column and a spiral concentrator were also used to process nominal 1.2 x 0.15-mm material. Product yields and ash contents were obtained for all tests, while partition curves were generated for selected tests from which the characteristic performance parameters (relative density of separation and probable error) were determined. The results indicated that the dense-medium cyclone was capable of cleaning down to 0.037 mm, while the other devices were effective to 0.15 mm. Keywords: Coal recovery, Coal refuse, Dense-medium cyclone, Hindered settling, Spiral concentration

Jan 1, 2003

By S Jahn, M Noel, E M. Rykaart, M Pau

Three soil cover test areas were constructed on waste rock backfilled into the Lichtenberg Pit, near Ronneburg Germany. A fourth, uncovered area was included as a control. Each test area measures 50 m by 65 m, and was constructed using full-scale equipment and construction practices. Extensive material sampling and testing was included as part of the construction. Devices were installed in each plot to monitor meteorology, infiltration, run-off, interflow, soil moisture, soil temperature, and soil pore gases. Boreholes were completed in each area and instrumented for temperature, pressure and pore gas sampling to a depth of approximately 60 m. Data from the monitoring instruments have been collected since July 2000, and have been comprehensively analysed and modelled on two occasions. The paper presents an overview of the test area design and instrumentation and the results of the two comprehensive data reviews. The reliability of the various monitoring methods is discussed and experience with several innovative methods is reviewed. The difficulties encountered in modelling the data set using common soil physical models are discussed.

Jan 1, 2003

By Xiao Songwen

Based on the anion coordination polyhedron growth unit theory, the polymorph transformation mechanism of antimony white (Sb2O3) in hydro-process was investigated. The new findings had been verified in the commercial-scale test and it was shown that adding a small amount of tartrate ions was economical and effective for polymorph transformation of antimony white in hydro-process.

Jan 1, 2003

By Paul Kunze

We have been told many times by legal folks and insurance types about the importance of producing accurate blast reports should you ever get dragged into court. In that venue the investigators will look at the information regarding product type and quantity, it’s distribution among the holes, and delay information in order to arrive at some judgement regarding vibrations or other blast induced phenomena

Jan 1, 2003

By T. Ito, N. Tokashiki, H. A. Bilgin, Ö. Aydan, T. Akagi

This study is concerned with the electric potential induced by deformation, fracturing and sliding of non-piezoelectric geomaterials. In experiments, the acoustic emissions together with electric potential measurements were also measured in order to see how the so-called seismic electric signals are associated with new fracture occurrence and propagation and sliding in case of existing discontinuities. The outcomes of this experimental study may explain why such electric potential variations may occur during the fracturing and sliding of non-piezoelectric geomaterials. On the basis of these outcomes, their possible implications in geo-engineering and geo-science are discussed. Ce travail concerne 1e potentiel électrique produit par la déformation, 1a fracture ou le glissement du matériel géologique non-piézoélectrique. Aux expérimentations, on a mesuré 1es émissions acoustiques avec le potentiel électrique afin de constater la relation entre les phénomènes de glissement ou de formation et de propagation de nouvelles fractures le long des discontinuités existantes. Les résultats de ce travail expérimental expliquent pourquoi de telles variations de potentiel electrique se produisent durant le glissement ou la fracture du matériel non-piézoélectrique. Sur la base de ces résultats, on a discuté de leurs éventuelles implications dans les domaines de 1a géologie et de 1a géo-ingénierie. Diese Studie befasst sich mit dem elektrischen Potential das durch die Deformation, Bruchbildung und Gleiten von nicht-piezoelektrischen Geomaterialien induziert wird. In Experimenten wurden die akustischen Emissionen zusammen mit elektrischen Potentialmessungen gemessen, um zu sehen, wie die so genannten seismischen elektrischen Signale mit neuer Bruchbildung und Ausbreitung sowie Gleiten im Falle von vorhandenen Diskontinuitäten verbunden sind. Die Ergebnisse dieser experimentellen Untersuchungen könnten erklären warum elektrische Potential Schwankungen während der Bruchbildung und dem Gleiten von nicht-piezoelektrischen Geomaterialien entstehen. Auf der Basis dieser Ergebnisse, wurden ihre möglichen Implikationen in Geoingenieurwissenschaften behandelt.

Jan 1, 2003

By Tetsuya Uda

Our recent achievements of rare earth separation technique[1,2] and new process idea for rare earth magnet recycling[3] are reviewed, (1) Binary chloride mixtures of rare earths were separated by a new selective reduction-vacuum distillation process. According to our experimental results, apparent separation factors were 8.1 for the Pr-Nd chloride mixture and 570 for the Nd-Sm chloride mixture. These values are much higher than conventional solvent extraction methods. (2) A study of recycling process of magnet sludge was carried out. The rare earths in the neodymium magnet sludge were extracted by chlorination with FeCI2, An activated carbon was used as a de-oxidation reagent Metallic iron in the sludge was not chlorinated because the iron monochloride is not stable, The extracted rare earth chlorides were easily separated from Fe-alloy and the excess of FeCh by vacuum distillation, 96 % of neodymium and 94 % of dysprosium in the sludge were extraeted into chloride phase, By the vacuum distillation, a mixture of neodymium and dysprosium trichlorides of 99.2 % purity was recovered, On the other hand, the rare earth chlorides can be converted to the corresponding oxides by a pyrohydrolysis reaction accompanied by a formation of HCl gas, The HCI gas can chlorinate metallic iron to FeCh, Therefore, a new recycling process for rare earth magnet waste can be realized as a chlorine circulation type process. During the process, only carbon and water are consumed and there are no toxic pollutants, Moreover, the obtained rare earth oxide can be directly used as raw material in the conventional oxide electrolysis process,

Jan 1, 2003

By S. Yap, F. J. Sotillo, L. P. Irwin, F. M. Utsey

Slimes, especially clays, are detrimental to several processes in the Mining Industry. The efficiency of classification, clarification, gravity separation, and flotation decreases significantly in the presence of slimes and clays. This problem is particularly critical in the Phosphate and Sulfide Industries. To reduce the effect of slimes in mineral processing, several desliming techniques and chemical additives are used, such as sodium silicate, sodium carbonate, sulfuric acid, tripolyphosphate, hexameta phosphate, etc. Lately, the Mining Chemical industry has shift to more “Specifically Developed” reagents that offer the most efficient and cost effective performance, mainly using organic polymers. For this purpose, the Mining Chemical Industry needs to understand the crystal chemistry of minerals, the chemistry of the aqueous media, the interactions in solids-aqueous-gas interfaces, the rheology of the system, and the plant operation conditions and parameters. This paper describes the use of surface chemistry fundamentals on the design of an organic polymer capable of modifying the rheology of clayish slurries of a phosphate ore. The change in the rheological characteristics of the clayish phosphate slurries allow fine ore particles to settle faster by reducing the slurry viscosity. Thus, abetter separation of the ore from the slimes is possible using gravitational or centrifugal forces. As examples of the application of this reagent, industrial and pilot plant tests on desliming using tanks and hydrocyclones are presented. These tests showed the reduction of 32%-36% in ore losses for different phosphate ores during desliming operations, and the increase of cyclones desliming efficiency to 80%. Tests were also carried out to improve the rejection of unwanted iron bearing slimes in phosphate feed. These tests demonstrated that it is possible to reduce by 0.25%-1.23% Fe2O3content in the flotation feed product. As a result, significant economical benefits are observed with the use of this new technology without any adverse effect on down stream operations, such as clay settling or phosphate flotation.

Jan 1, 2003