Search Documents

By R. M. Taylor

Lime addition to acid mine drainage (AMD) leads to precipitation, predominantly of metal hydroxides and calcium sulfate, and is the benchmark for remediation by precipitation. Geo2 Limited of Melbourne, Australia has developed and patented a novel alternative precipitation scheme based on the formation of mixed valency, M(I1)-M(III), hydroxide sulfate salts. When the composition of AMD is appropriate, the Green Precipitate Process provides a useful and more effective alternative to conventional liming. The characteristics and utility of the Green Precipitate Process are described in terms of the underlying chemistry, and a case study where the Green Precipitate process outperforms conventional liming. A mobile pilot pipe reactor rig which was built by Geo2 to demonstrate the process, and used successfully in both Australia and the United States, is described.

Jan 1, 1998

By T. Shoji

"The human history is characterized by social development based on mineral and energy resources, and many conflicts to take the resources by power. This is shown by not only world wars but also many local conflicts as well as international supremacy.IntroductionThe world population after B. C. 10000, which is summarized in several papers, is approximated by four straight lines on a semilogarithmic diagram as shown in Figure 1 [l]. The annual rates of increasing are 0.0041, 0.071, 0.53, and 1.85 % from the old and young periods. The boundaries among four periods are approximately B. C. 4600, AD. 1670, and 1930. The start of the second period seems to correspond to the beginning of agriculture and cattle breeding. Precisely speaking, the usage of natural energy resources such as woods and domestic animals already began, but is inferred to have become common after the age. The third and fourth periods are characterized by the common usage of coal and oil, respectivety. Not only energy resources but also mineral resources including gold, copper, iron and others are also important for the human history.Mineral and energy resources have supported the development of the .human civilization, and have caused many conflicts because of this reason. Every day newspapers report conflicts, such as Chechnya, East Timor and Ache. We can easily point out the facts that the conflicts closely relate to mineral and energy resources. Groznyj, Capital of Chechnya, is located on the western margin of Caspian oil field. Many mineral deposits occur in Kavkaz Mountains running south of Chechnya. Subsea oil fields occur in Timor Gap located between East Timor and Australia. Ache is also one of oil fields in Indonesia. It is very difficult to state present conflicts independently of a political view of point. For this reason let us try to historically review the relation between mineral and energy resources and international domination and conflicts [2] based on many papers [3]."

Jan 1, 2000

By D. Raghavan

In recent years, the environmental issues related to the landfill shortage received considerable importance. Many polymeric solid wastes have high resistivity to chemical and biological degradation, and options are sought by which these wastes can be recycled and reused, or reduced in volume. The present study investigated the biodegradation of polyethylene by Aspergillus niger, and biodesulfurization of rubber by pure and mixed cultures of Thiobacillus thiooxidans and Thiobacillus ferrooxidans. The fungus, A. niger, was found to metabolize portions of polyethylene. Quantitative calorimetric measurements revealed that the amorphocity of the sample decreased during biodegradation. Removal of sulfur from synthetic rubber samples containing 2 to 15% sulfur, was studied in shake flask experiments and the associated oxygen consumption was studied in Warburg respirometers. The mixed bacterial cultures were more effective in the desulfurization of rubber samples than the pure cultures of T. thiooxidans and T. ferrooxidans. The data obtained in these studies may have far reaching consequence for the development of new effective processes regarding the remediation and management of discarded polymeric packaging wastes and car tire rubber materials.

Jan 1, 1993

By Willem P. C. Duyvesteyn

A novel hydrometallurgical process for Escondida copper concentrates has been developed by The Minerals Laboratory of BHP. The Escondida Process consists of concentrate leaching, solution purification, electrowinning and residue flotation. Part of the copper will be sold as high grade concentrate and part as high purity SX-EW copper. Contrary to previous efforts for the development of a hydrometallurgical process for copper concentrates, this patented process does not advocate the total dissolution of copper. It only aims for the copper that is readily soluble in a mildly oxidizing environment with an ammoniacal or acidic lixiviant. Both lixiviants were studied, but ammonia was preferred because of fast kinetics at ambient temperatures and pressures. By controlling the oxidation potential, the formation of sulfate ions and, consequently, of an ammonium sulfate byproduct, is precluded. These mild leaching conditions also prevent the dissolution of unwanted impurities and result in the production of ultra-high purity electrowon copper. Solution purification is carried out by solvent extraction with LIX-54. The very high loading capacity of this organic results in a compact SX circuit, consisting of two loading, one scrubbing, and one stripping stage. As the organic is selective for simple copper ions, the copper amine complex is broken down and free ammonia is regenerated and recycled for leaching. High purity copper cathodes are produced in a conventional sulfuric acid based electrowinning system. One scrubbing step is needed to separate the ammoniacal circuit from the acid circuit. Limiting copper dissolution to less than 50% also provides an opportunity to produce high grade concentrates by residue flotation. Copper recoveries in excess of 98% with precious metal values reporting to the final concentrate can readily be obtained. Complete breakdown of the copper mineral- pyrite middlings results in a final concentrate grade that can be even higher than the original feed material. The Escondida Process also provides an opportunity to accept lower grade copper concentrates producing improved copper recoveries in the mill and yet high quality concentrates for marketing. The Paul E. Queoeau International

Jan 1, 1993

By M. Goto, T., Matsutani, T. Igarashi

"PT. Smelting was established in February 1996 as a company to· construct the first copper Smelter and Refinery in Indonesia with US$500 million direct construction cost and operate it. The plant is located in Gresik, East Java, Indonesia and 20km northwest from Surabaya, 2nd largest city in Indonesia. The site was selected due to following .advantages.1. Adjacent PT: Petrokimia Gresik, - a fertilizer company, purchases all sulfuric acid produced through pipeline.2. Facing on the seashore of the Madura Strait, it is possible to unload copper concentrate from West Papua (3,000km from Gresik) and load granulated slag to the market.3. Close to the good harbor facilities at Surabaya for export the products.4. Gresik Industrial Area has adequate infrastructure.5. Surabaya is a quite nice city to live for people from abroad.The shareholder of PT. Smelting are Mitsubishi Materials Corporation (60.5%), PT. Freeport Indonesia (25:0%), Mitsubishi Corporation (9.5%) and Nippon Mining and Metals Co. Ltd. (4.5%).The Gresik Copper Smelter and Refinery is designed to produce 200,000 tpy of copper cathode from 660,000 tpy of copper concentrates supplied 100% by 'Grasberg Mine of PT. Freeport, Indonesia in West Papua (former Irian Jaya). Other by products are 600,000 tpy of sulfuric acid, 30,000 tpy of gypsum, 509 tpy of precious metal slime and 400,000 tpy of granulated slag. These are sold to domestic and international markets.This project adopted the Mitsubishi Continuous Copper Smelting and Converting Process in the Smelter for anode casting, Contilanod process comprising Hazelett twin belt caster and a Mannesmann's travelling shear were selected. ISA stainless steel cathode process is applied in refinery. The combination of contilanod anode and stainless steel cathode ensured good cathode quality from the very beginning of start-up SO2 gas generated from Smelter is treated by Lurgi-Mitsubishi double contact/absorption acid plant. All contact. wastewater from the plant is treated in multistage wastewater treatment plant.Electricity and oxygen are ·supplied ""over the fence"" by a company which is located in the site of the Gresik Smelter and Refinery."

Jan 1, 2000

By Timothy W. Ellis

This paper presents the basic theory of operation, physical chemistry and phase equilibria which allow the development of liquid-liquid extraction circuits based on metallic solvents. The incorporation of reduction and reduction/diffusion processes into the process 'scheme is discussed and a detailed description of ,several liquid-liquid extraction schemes are developed. A synopsis of experimental results obtained using this: method to separate rare earth and other metal based materials will be given.

Jan 1, 1996

By Akira Yazawa

The similarities and differences in copper, nickel and lead smelting processes are discussed based on the sulfur-oxygen chemical potential diagrams and the free energy minimization assessments using a thermodynamic software. The prominent features of copper smelting are ascribable to the fact that copper has a strong affinity for sulfur but weak for oxygen and the liquid phase immiscibility between Cu and Cu2S. During the oxidation of sulfides, nickel metal is not stable except at temperatures higher than 1500°C, well miscible with its sulfide, and is oxidized more easily than copper. Metallic lead looks as stable as copper during the oxidation of the concentrate but Pb and PbS. are much more miscible with each other and the vaporization loss is considerable. In the reductive smelting of oxides, the effects of oxygen potential and temperature on the copper contents in slag are not significant due to the monovalent character of copper and the reduction of copper content in slag is not easy in practice. The effect of the slag compositions on the oxidic metal contents of slag is much more significant for lead than either copper or nickel. Due to the immiscible nature between Pb and Fe, high grade lead bullion is easily obtained and lead is more tolerant to impurities.

Jan 1, 1998

By J. W. Evans

Mathematical modeling has now become a standard technique in the development of new technology and the improvement of existing technology in the processing industries. Physical modeling has a longer history but a smaller following at present. The paper reviews some examples of the application of both types of modeling in non-ferrous metal extraction, particularly within the copper and aluminum industries. The objective is to show that well founded models can lead to results that have practical consequence in scaleup, design and operation.

Jan 1, 1993

By Amy Anderson

The Silica (SME) Technology has been utilized on three separate projects focusing upon the stabilization of mercury-contaminated materials: at the Mother Lode Mine in Oregon, the Sulfur Bank Mercury Mine in California and at a former chloralkali plant in British Columbia. Each of the projects relied primarily on the results collected via EPA Method 1311 TCLP, with additional tests such as SPLP, humidity cell tests and other supporting tests employed as well. Both technical and economic performance of the silica-based technology was evaluated as well as that of competing technologies in some cases. Results established that in each of the three projects an SME chemical dosage rate of 3% chemical by weight of soil/sludge was the optimal ratio required to achieve project treatment objectives, TCLP test results exhibited a reduction in the leachable mercury from the treated materials ranging between 75% and 99% as compared to untreated material, satisfying the technical objectives for each project, Project costs ranged from $l5.00 - $18.26 per metric ton.

Jan 1, 2003

By Honggang Zhong, Xin Cao, Qijie Zhai, Hongmei Song, Congsen Wu, Cheng Zhang, Jingzheng Ye

"The influence of superheat on the solidification structure and ferrite/austenite phase transformation of a novel lean duplex stainless steel (DSS) was investigated on a setup, which designed to thermally simulate the continuous casting process. The results showed that the macrostructure of the samples all exhibited chill zone, columnar zone and equiaxed zone. The distance from chill zone to position of columnar to equiaxed transition (CET) moved from 51.0 mm to 39.8 mm with an decrease of superheat from 70 °C to 10 °C, and that the grains in the chill zone tended to be finer. In equiaxed zone, the fme and uniform grains were observed when superheat higher than 40 °C; while, coarse grains were found in samples poured at low superheat. Generally, the volume fraction of ferrite increased along the dendritic growth direction, and stabilized in equiaxed zone. The high superheat decreased the volume fraction of ferrite in equiaxed zone, while it had indistinctive influence on chill zone and columnar zone.IntroductionDuplex stainless steel with approximately equal volume of ferrite and austenite, offering an attractive combination of corrosion resistance and mechanical properties. [ l]. The production of DSS, worldwide application in structural engineering[2] and petrochemical industry[3], have increase by more than 100% in the latest decade[4]. But due to the sharp prices increase of nickel and chromium, lean duplex stainless steels which have lower contents of alloy elements were developed. They perform well in both mechanical and corrosion resistance[S, 6] and even have TRlP(Transformation Induced Plasticity) effect[?]. Nonetheless , the mechanical properties of DSS was affected greatly by the solidification structure, such as columnar to equiaxed transition (CET), grain size and phase content[8]. So, the solidification behavior of stainless steel was investigated widely"

Jan 1, 2014

By Marco Olper

The Italian company Engitec Impianti has developed a new electrochemical technology for the treatment of Electric Arc Furnace (EAF) flue dust generated in steel mini-mills. This process is based on a new and completely different concept from the Waeltz technology applied at present and allows, due to its modular nature, for an erection on the steel producer's site. Engitec Impianti spent US $700.000 constructing a 500 t/y throughput pilot plant at Pittini Group's Ferriere Nord mini-mill in Osoppo, Italy in order to demonstrate the process capabilities and obtain the data for a commercial plant design. The paper describes the pilot plant performances and the engineering criteria for a commercial unit of 10.000 t/y throughput. The feasibility study demonstrates a pay-back period of 3 - 4 years for the commercial plant.

Jan 1, 1995

By Y. K. Rao

In the carbonyl process for the refining of crude nickel CO(g) reacts with nickel in the 310-370K range producing nickel tetracarbonyl, Ni(C0)4(g). Iron and cobalt impurities also form gaseous carbonyls but their partial pressures are low. The carbonyl is led to a decomposer plant wherein the gas disproportionates in the 500-600K range depositing pure metal on nickel pellets that move countercurrent to the gas-flow. This system serves to illustrate the fundamental principles involved in the vapor phase mass transport of elements, against temperature-gradient, under the influence of chemical potential gradient. Unlike in the crystal growth, the source is at a lower temperature (say 350K) whereas the seed is in the hot-zone (say 550K) of the closed ampoule-type reactor. By assuming virtual gas-solid equilibria in the end zones, with diffusion of gaseous species between them acting as a slight perturbation, the quasi-steady- state mass-transport rates are computed for a range of CO-pressures and temperatures.

Jan 1, 1993

By Mahesh C. Meyer Jha

AMAX has developed a chloride refining process to produce pure nickel and cobalt metals from mixed sulfide .precipitates, Metal chloride solutions, generated in a hydrochloric acid leaching step and purified in a solvent extraction circuit, are converted to metal oxides .and HCI gas by pyrohydrolysis. A pilot plant consisting of a 30-inch diameter fluidized bed reactor and other ancillary units was designed, constructed, and operated for over one year. Process design was aimed at minimizing energy consumption, maximizing conversion efficiency, and achieving simplicity of operation and control. The operation provided valuable information on process scale up parameters, process control strategies, and materials of construction., Several process variables such as bed temperature, solution composition, solution feeding system, bed particle size distribution, and fines recycle system were investigated to determine their effects on process efficiency and the physical and chemical characteristics of the product.

Jan 1, 1985

By S. M. Hay

The zinc content of blast furnace and basic oxygen furnace dusts is low compared with electric arc furnace dusts and it is generally not economical to treat the dusts to recover zinc. However, they have a high iron content and removal of the zinc would allow recovery of the iron values. A literature review and thermodynamic analysis was undertaken and, as a result, several smelting options were identified. This paper describes experiments undertaken to develop understanding of metallurgical aspects of these processes which are not amenable to theoretical analysis. Dusts from an Australian steelworks were characterised in order to determine their mineralogical make-up and the form of the iron. The processing aspects investigated in the laboratory were slag-metal equilibrium and solid-state pre-reduction using reducing gases of compositions expected from bath-smelting processes. Particular attention. was paid to the deportment of zinc, sodium, potassium, phosphorous and sulfur between the phases formed during smelting and pre-reduction. The smelting results indicate that less than 10% of the zinc, sulphur, sodium and potassium report to the metal. About 99% of the zinc and potassium and about 80% of the sodium could be volatilised from the dusts by reducing them at 1,000°C with mixtures of CO, CO2, H2 and H2O even when metallic iron was not formed. The experiments indicate that smelting of blast furnace and basic oxygen furnace dusts should produce hot-metal of a composition which can be blended into the main stream of hot-metal in the steelworks.

Jan 1, 1994

By Young-Dae Kim, Dong-Sic Kim, Jong-Jin Pak, Kyung-Hyo Do

"Sulfur is one of the most harmful elements in stainless steel (SIS) products and the specification of sulfur content is getting more severe for high grade SIS. In order to accurately control the desulfurization reaction in high chromium containing SIS melts, it is important to know the thermodynamic interaction between chromium and sulfur in Fe-Cr melts over a wide range of chromium content. In this study, the equilibrium sulfur distribution, Ls, between a Ca0-Alz03 slag and Fe-Cr-C,.,-S melts were measured under CO atmosphere in the temperature range of 1823-1923 K. The specific effect of chromium on the activity coefficient of sulfur in the melts was determined with the consideration of carbon effect on sulfur. A separate experiment was carried to determine. Ls between a slag and FeCr- S melts (Cr: 0-30 mass%) at 1873K to check the validity of the thermodynamic parameter determined in the present study.IntroductionFerritic stainless steels containing chromium (Cr) up to 30 mass% have been developed for a good corrosion resistance and a high formability to replace austenitic SIS. Especially, Sulfur (S) causes a reduction of high-temperature strength and the hydrogen induced cracking (HlC) in stainless steel for line pipes. [l]Many studies on the desulfurization of hot metal and liquid steel have been carried out for several decades and they used HzS-H2 gas equilibrium technique for measuring the effects of many alloying elements on the activity coefficient of S in liquid iron. However, the study on desulfurization of Fe-Cr melts was very scarce.[2] In order to accurately control the desulfurization reaction of high Cr stainless steel, it is essential to know the thermodynamic relation between Cr and S in Fe-Cr melt over a wide range of Cr content and temperature.In the present study, the thermodynamic interaction between Cr and S in liquid iron was determined by measuring the equilibrium distribution ratios of S between Fe-Cr-C,.1-S melts containing a wide range of Cr up to 30 mass% and a 55 mass%Ca0-45 mass%Alz03 slag of which the sulfide capacity was pre-determined using Fe-C,a1-S melts in the temperature range of 1823-1923 K. The validity of thermodynamic parameter determined in the present study was checked by measuring the S distribution between a Ca0-Alz03-Mg0 slag of known sulfide capacity and liquid Fe-Cr-S alloy at 1873 K. Using Wagner's formalism, the results of experiment were thermodynamically considered to determine the effect of a specific concentration of Cr on the activity coefficient of S in liquid iron."

Jan 1, 2014

By Grant E. Casley

Since 1970 Mount Isa fines Limited has made a significant increase in blister copper production from approximately 100,000 to 155,000 mt per annum and in fact 161,040 mt were produced in the calendar year 1974. Flowsheet developments including fluidised bed roasting and converter slag flotation are discussed, particularly their contributions to minimising major equipment changes in smelting and converting. The use of model- ling and simulation techniques for such an exercise is mentioned. The paper reports the alterations made to both equipment and operating techniques in the reverberatory furnace and converter sections to achieve the regular production of 250 mt of blister per converter day from a 41% Cu matte grade. The effects of flux composition on converting performance are highlighted. The air quality control programme is discussed in relation to its restriction of blister copper production.

Jan 1, 1976

By M. B. Sizgoric

Quantitative mineralogy is used in a study done on an Inco Metals Company nickel sulfide occurrence from 'the Thompson area in Northern Manitoba. The study included: a) determination of the variations in chemical composition of the ore minerals; b) determination of the liberation of the ore minerals for the various types of ore and for different feed grinds; c) assessment of the preliminary mill test results by comparing the mineral distribution in the different tailings. Preliminary mill test results had outlined three main problem areas: 1) unacceptabiy low grade concentrate with, 2) very high weight recovery and, 3) low pyrrhotite rejection resulting in a high sulfur concentrate. The mineralogical study readily explained these results by showing that: 1) between 20 and 40% of the nickel in the feeds and 55 and 75% of the nickel lost in the tailings is associated with pyrrhotite. This accounts in part for the low grade of the concentrates obtained at high recoveries: 2) hexagonal nonmagnetic pyrrhotite constitutes over 90 percent of pyrrhotite. Since hexagonal pyrrhotite floats more readily than monoclinic pyrrhotite, this could be part of the reason for the undesirable high pyrrhotite recoveries into the concentrates. Further test work to establish both the optimal grind and the best conditions for pyrrhotite rejection is therefore mandatory.

Jan 1, 1981

By Nicholas Zabaras, Deep Samanta

"Solidification of metal aluminum and aluminum alloys is modeled on uneven surfaces characterized by sinusoidal curves. Wavelengths and amplitudes of these sinusoidal surfaces are varied to study their effects on processes like solidification, macro-segregation and inverse segregation. Solidification and macro-segregation are modeled using a slightly modified form of a stabilized finite element method developed recently to model high Rayleigh number solidification and porous media flows. For pure metal solidification, the effect of varying amplitudes and wavelengths is observed in heat transfer, fluid-flow ~nd phase change processes. The relative importance of shrinkage driven flow and solutal convection on the redistribution of solute for an alloy solidifying in a rectangular cavity is compared. The analysis is then extended by modifying one of the surfaces to a sinusoid. In this case the effects of varying amplitudes and wavelengths are studied in heat transfer, fluid flow, phase change, macro-segregation and inverse segregation processes.1 IntroductionTransport phenomenon during solidification of alloys is a major cause ofcasting defects such as segregation, micro-voids, hot tears, porosity, internal and surface cracks. Heat flow across metal and mold surfaces directly affects the phase change process and plays an important role in determining freezing conditions within the metal. In alloys, natural convection and shrinkage play an important role in determining the final solute redistribution, macrosegregation and evolution of solid macromorphology. Surface unevenness plays an important role during the early stages of solidification. It influences the heat transfer rate and fluid flow in the melt, which in turn affect the morphology and shape of the solid-liquid interface. The effect of surface unevenness on solute redistribution is important during solidification of alloys, where solute driven flow in the mushy zone is prominent. Thevik and Mo in [7] and [8] used a one dimensional model for studying surface segregation and macrosegregation in alloys under the influence of exudation and solidification shrinkage. Air-gap formation in their model was expressed through a variable convective heat transfer coefficient at the boundary. Tsai et al. in [3] and [4] have modeled macrosegregation in an aluminum-copper alloy driven by shrinkage and solutal convection. They used a single domain model based on mixture theory and solved the transport equations using finite difference methods. Our aim is to model solidification of aluminum followed by macrosegregation and inverse segregation in aluminum-copper alloys on uneven surfaces by finite element methods. These surfaces are modeled as sinusoids characterized by amplitudes, ?s and wavelengths, As, By varying As and ?s, changes in heat transfer, fluid flow, phase-change and macrosegregation are studied."

Jan 1, 2004

By W. L. Dalmijn

Glass recycling in the Netherlands 'has grown fr.om 10.000 to 300.000 tonnes per annum. The various advantages and problems of the glass cycle with reference to the state of the art in the Netherlands is given. Special attention is given to new technologies for the automated sorting of cullet with detection systems. In Western Europe the recycling of glass has, become a success story. Because of this, the percentage of ,glass cullet used in ,glass furnaces has increased. To meet the quality demands of the glass industry, automated sorting for the removal of stones, non-ferrous metals and other impurities ,had to be developed and incorporated in glass recycling plants. ;In Holland, Germany and other countries, the amount of glass collected has reached a level that colour-sorting becomes necessary to avoid market saturation with mixed cullet. Recently, two systems for colour-sorting have been developed and tested for the separation of bottles and culletin the size .range of 20 -50 mm. With the increased capacity of the new glass recycling plants, 120,000 -200,000 tpy, the quality systems have also to be improved and automated. These quality control systems are based on tile automated sorting technology developed earlier. for the glass recycling plants. The data obtained are automatically processed and printed. The sampling system and its relation to the theory of Gy will be described. Results of both developments in glass, recycling plants will be described.

Jan 1, 1995

By Pengfu Tan

NiModel, a thermodynamic model, database and computer program, has been developed to predict the distribution behavior of Ni, Cu, Co, Fe, S, O, As, Sb and Bi, and heat balance in the nickel pyrometallurgical processes such as Outokumpu flash smelting, Outokumpu direct high-grade matte smelting, INCO flash smelting, and Peirce-Smith converting processes. In this model, as much as 16 elements (Ni, Cu, Co, Fe, As, Sb, Bi, S, O, Al, Ca, Mg, Si, N, C and H) are considered. The compositions of matte, slag and gaseous phases, and heat balance are calculated using the thermodynamic data and the activity coefficients of the components derived from the experimental data. The model predictions were compared with the known industrial data from Kalgoorlie Nickel Smelter in Australia, Outokumpu Harjavalta Nickel Smelter in Finland and INCO Metals Company in Canada, and an excellent agreement was obtained. In this paper, the applications of NiModel in the nickel pyrometallurgical industries have been presented. NiModel has been used by Jinchuan Group Limited in China.

Jan 1, 2004