Search Documents

By W. Dutton, D. Simms

"The clearing of tuyeres on copper and nickel converters or similar metallurgical, vessels has, for many years, been done using mainly a manually- operated ""puncher"". One such device is the ""Gaspe Puncher"" developed in 1962 at Noranda's Gaspe Smelter. In an attempt to remove the operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor.The automated puncher is controlled by a Texas Instruments Model 530C Programmable Controller (PLC). Position measurement and control is done using non-contact position measuring equipment from the Tele-Controls Division of Geodimeter Inc. The entire automation system was installed on an existing Gaspe Puncher with minimum disruption to the operation of the smelting process. The operator's panel allows the user to ""block out"" any individual tuyere, and to select any of a variety of operating modes.The development of the automated puncher is described, and the results of several months operation are given.IntroductionThe tuyeres of copper and nickel converters and similar metallurgical vessels become blocked with solidified material formed by the cooling action of the blowing air. This restricts the converting operation. Clearing these blocked tuyeres has for many years been done mainly using a manually-operated ""puncher"" which uses a hydraulic or pneumatically-operated piston to drive a steel bar into the tuyere. The Gaspe Puncher, developed at Noranda's Gaspe Smelter in 1962 is one such device. It is currently being built and sold by Heath & Sherwood (1964) Limited, under license to Noranda. There are over 200 units in operation world-wide.In an attempt to remove the Puncher operator from the cab of the Puncher, and to relieve him of a tedious, uncomfortable job, and to increase productivity, Noranda's Horne Division, in cooperation with Heath & Sherwood (1964) Limited and the Noranda Research Centre, undertook to automate the Gaspe Puncher used on the Noranda Continuous Smelting Process Reactor. This paper describes the development of the automated Gaspe Puncher, its installation at the Horne Smelter, and the results of its operation after several months."

Jan 1, 1989

By Tetsuro Sakai

Home appliance recycling law was put into force in April 2001 in Japan. Specified kinds of home appliances, such as air conditioners, television sets, refrigerators and washing machines, should be recycled according to the law. Mitsubishi Materials Corporation (MMC) in cooperation with home appliance manufacturers is operating five home appliance recycling plants in Japan. MMC established complete treatment system of recyclable materials generating from home appliance recycling plants, which is formed by unique collaboration among home appliance recycling plants, copper smelter and refinery, and cement plants. Recyclable materials containing copper and precious metals are only handled and treated within the MMC group. By using this lock-in system, safe treatment and traceability of materials are guaranteed as 100% materials recycle.

Jan 1, 2008

By Kurt Westerlund

Three. years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm /h at Boliden Ronnskar Sweden on a TBRC smelting palena (PbS). Operating experience from the Kivset flash WHB 11.900 nm /h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3 /h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By Kurt Westerlund

Three years operating experience of the FLUXFLOW waste heat boiler (WHB) 20.000 nm3/0h at Boliden Rönnskär Sweden on a TBRC smelting galena (PbS). Operating experience from the Kivset flash WHB 11.900 nm3/h at Samim, Porto Vesme, Sardinia, Italy. Conceptual features of the 93.600 nm3/h FLUXFLOW (WHB) on the Isasmelt smelting in melt furnace for 180.000 t Cu/a at Mount Isa, Australia.

Jan 1, 1992

By A. F. Usov

"The use of the Electric Pulse Discharge method of materials destruction (EP) for disintegration of materials in an industrial-waste processing are examined. The principles and Experience of the development device of EP-disintegration have been described, the technological efficiency of disintegration of industrial minerals estimated.IntroductionThe Russian scientists have proposed and comprehensively studied the electric pulse (EP) technique which is applied in ores and materials disintegration [1, 2 ]. The different aspects of the problem have been presented by the authors in papers at many international congresses [3-6]. Recently the technique is intensively developed in many countries, and various disintegration installations are exhibited.Crashing and disintegration of ores by EP-method is characterized by high selectiveness of destruction. It provides better disclosure of mineral grains and prevent it from destruction. EPmethod reduces slurry formation. All this provides better mineral extraction at ore beneficiation and improves concentrate quality. It also prevents the product from polluting with equipment metal, inwall and grinding equipment material. The possibility to change the character of dynamic loading allows controlling grain-size composition and getting small-size product in contrast to mechanical method of crashing.The product of EP-crashing is characterized by less toughness and greater specific surface area of grains since the new surface is formed at splitting and chinks extension. The product is of high sorption and reactivity in chemical changes. Open grains of mineral spots correspond to their natural condition and it is of great importance for studying mineral.The principles of the development deviceLong-term studies of the technique carried out by research institutes such as Research Institute of High Voltages (Tomsk), Kola Science Centre of RAS (Apatity), Institute ""Mekhanobr"" (S.Pertersburg), made it possible to substantiate principles of the disintegration installations design, make exploratory stands and technological installations to carry out pilot tests and operations under production conditions. The construction design of disintegrating installations depends on many technological and physical factors. Of all the technological factors, the most significant one is to preserve the liberated product because it is the peculiarity of the EPdisintegration to have high selectivity of disintegration. The preservation of the mono-mineral product liberated from the rock mass means that this product is not overgrinding, which causes the loss of the product with slime in processing, and that the initial natural form of the mineral inclusion is also preserved because it is the size and the integrity of crystals that determines its cost value (precious minerals). On the one hand, it is provided by a stage disintegration technique, with the product classified after each stage, and, on the other hand, by selection of specific conditions of electric breakdown, which ensure high performance of electric breakdown and effective disintegration of material fragments, with the useful mineral inclusions preserved intact, with its size considerably exceeding the discharge gap. These conditions are provided by the appropriate geometry of electrodes, the discharge gap and the screen size due to the material’s nature and grain size."

Jan 1, 2008

By Wolfgang Baum

Remediation work on thermal process dusts and slags has been primarily based on chemical analyses. These data offer little information for the assessment of treatability and reuse potential. In addition, the lack of mineralogical residue characterization has frequently caused time-consuming and inefficient waste management. This paper will outline the cost-effective, and sucessful use of process-oriented mineralogical analyses for treatment and beneficial reuse of various thermal residues. These include a patented process for detoxification of Pb-contaminated bottom ash, the pyrometallurgical treatment of K 061, the reprocessing of lead smelter slag as well as various power plant residues.

Jan 1, 1992

By Andreas Dietrich

Laser off-gas measurement of CO, O2 and temperature has been carried online in EAFs. A visualization screen shows the values of CO and Oxygen and temperature for the entire heat, and includes the status of furnace equipment. The historical data of the heats are stored such that the furnace performance can be evaluated and optimized. A short comparison between laser based and conventional systems has been carried out related to speed, influence of dust, water, pressure, protection for bag house explosions. A high water and/or dust content in the sample does not represent a problem for this type of system. The measurement method works without interruption even under worst conditions such as dirty scrap, carbon injection etc. The installation was developed in conjunction with Marienhuette, Graz. They are 100% scrap based with a tap to tap time of ca. 46 min. Keywords: Laser Measurement, Off Gas, CO, O2, Temperature

Jan 1, 2003

By E. L. Frueh

AMAX Base Metals Research & Development, Inc. has developed a process for treating copper-nickel mattes to produce copper cathodes and a pure nickel sulfate solution. In this process, the input matte is preleached in a copper sulfate electrolyte bleed solution so as to dissolve nickel from the matte and cement copper from solution. The preleach leaves a substantially pure nickel sulfate solution. The residue from the preleach is roasted to less than about one percent sulfur. A portion of the calcine is leached with sulfuric acid to make a copper sulfate solution for input to the tank house. The residue from this leach and the remaining calcine are smelted to form a bimetallic (copper/nickel.) anode. The anodes are electrolytically refined and copper is preferentially deposited on the cathode while the nickel reports to the electrolyte, A bleed stream is taken from the electrolyte and used in the preleaching of the input matte. This process produces high purity metal streams while consuming less energy and smaller amounts of reagents as compared with other matte processes.

Jan 1, 1983

By Alva L. Kuestermeyer

This paper presents the results of an economic analysis in the production opportunities of various co-product and minor metals in the base metals smelting 'industry. Pro forma cash flow statements were prepared for each co-product and/or minor metal analyzed utilizing US tax laws for items such as depreciation and taxes. The generated cash flows are based on anticipated revenues, estimated capital and operating costs (where applicable), and nominal production data for the respective co-products and minor metals. The economic analysis includes consideration of items such as metal payfors and bonus metals ,payments per current smelting terms. Sensitivity analysis to market prices is also ,addressed.

Jan 1, 1995

By Milan Lj. Stamatovic

The hydrometallurgical recovery of zinc from recycled blast furnace dust from a steel plant (Smederevo Metallurgical Company - Yugoslavia) was investigated. The dust contained 22% Fe, 17% Zn and 0.2% Pb. X-ray diffractometry showed that the main components were hematite and magnetite, in combination with zinc oxide and a very low content of lead oxide. Individual particles were generally spherical and ranged in size from 10 to 150 microns; 63% were less than 33 microns in diameter. An effective hydrometallurgical approach proved to be by caustic leaching followed by electrowinning. Recovery of zinc in the form of zinc powder was over 90%. This powder can be used for the cementation of impurities in the conventional hydrometallurgical process for zinc production.

Jan 1, 1993

By E. Legault-Seguin

The current industrial practice in the processing of nickeliferous laterites involves the precipitation and releaching of Ni and Co to allow separation from the major impurities of Mn, Mg and Ca. A direct solvent extraction process has significant advantages over this practice, which suffers from difficult and costly precipitation steps, lower recovery and inherently complex flowsheets. The present investigation involves the examination of Cyanex 272, Cyanex 301 and Cyanex 302 as extractants for the direct extraction of Ni and Co from major impurities associated with laterite leaching, i.e. Mn, Mg and Ca. For Co extraction, Cyanex 301 and Cyanex 302 are superior to Cyanex 272, because they are able to selectively separate Co from Mn, Mg and Ca. Cyanex 272 offers complete extraction of Co from Ni and Ca, but Mn and Mg pose difficulty. Ni can only be extracted selectively with Cyanex 301, thus another extractant selective for Ni, such as Versatic 10 or Cyanex 301, is needed to recover Ni if Cyanex 302 or Cyanex 272 is used for the initial extraction.

Jan 1, 2004

Off-gas cleaning from metallurgical plants requires? in many cases very low dust contents which are difficult to achieve with conventional scrubbers, even with high energy input. Lur.gi has developed a scrubber which improves the separation of the fine dust by electrical charge prior to. the scrubbing zone. An Electrostatic Scrubber has been successfully installed for the off-gas cleaning from slag' granulation after a waelzkiln achieving less than 1 mg/m3 in the clean gas.

Jan 1, 1992

By A. F. Sidorov

A method of improving mineral recoveries from ores by modifying the physical and chemical properties of minerals using radioisotope radiation was tested. It was observed that irradiation modifies mineral cell sizes, changes the crystal structure of some minerals, reduces the sulfur content 1 to 1.5 % in sulfides, changes the zeta potential, alters the surface properties of mineral grains I and produces other changes. Preliminary tests indicate that accelerated electron treatment of ores in connection with mineral processing has a potential for improving mineral recoveries by flotation and by magnetic separations.

Jan 1, 1989

By Vladimir Kislik

Competitive complexation/solvation theory of solvent extraction constitutes a general framework for interpretation and quantification of ion-molecular interaction data in extraction systems. Depending on extracting metal -- solvent affinity constant and metal concentration ratios, four possible stages of extraction behavior and interacting mechanisms, are considered. Affinity constant ratios are easily acceptable through the independent measurements of three-component systems. Once determined and tabulated, the affinity constant ratio data may be used in any system of interest. Mathematical descriptions of the results are introduced for different interactions. Active solvent (including water) concentrations in the organic phase and temperature are included to the quantitative consideration. The theory allows direct comparison of the complexing/solvating power (competition order) of various extractants, active solvents and diluents. As a result, predictions for the extraction effectiveness and selectivity are possible. Some metal extraction systems are analyzed on the base of the theory. Analysis gives a key for preliminary quantitative prediction of suitable extraction systems.

Jan 1, 2003

By Qingwei Qin, Ping Xue, Guangqiang Li

Ausmelt furnace slag contains about 0.9% Cu (mass %). With increasing the amount of Ausmelt furnace slag, the recovery of copper from it will produce an enormous economic yield. The recovery of copper by floatation from slow cooled Ausmelt furnace slag was studied in this paper. The phases and composition of the slow cooled slag were analyzed. The factors which affected the copper recovery efficiency such as grinding fineness, pH value of flotation medium, different collectors and floating process were investigated. It was shown that the size distribution of the primary grinding and secondary grinding of middling were 75% for particles less than 0.074mm and 82% for particles less than 0.043mm respectively. The closedcircuit experimental results with butyl xanthate as collector in laboratory showed that the copper grade reached 16.11% and the recovery rate of copper reached 69.90% and the copper grade of tailings was only 0.2%.

Jan 1, 2015

By Bernhard J. Ralph

In refractory gold ores much of the gold occurs in sub-microscopic form in sulfide minerals, most commonly pyrite and arsenopyrite Bacterial leaching is being developed as a pretreatment for these minerals to aid the liberation of gold and a variety of extracting reagents. This paper reviews the nature of the principal micro-organisms involved, the effects of various physico-chemical factors on the rate and extent of extraction, and likely mechanisms involved.

Jan 1, 1989

By Beatriz Ribeiro Nogueira, Vijaya Kumar Rangari, Esperidiana A. B. Moura, Anne Chinellat, Arifa Parveen, Angel Visentim Ortiz

"Composite consisting of ethylene vinyl alcohol (EVOH) with short piassava fibers were prepared by extrusion process and their thermal and morphological behavior were investigated. The EVOH reinforced with 5 and 10 % of pi as sa va (Attaleafunifera Mart) fiber particle, based on the percentage weight ratio (wt %), untreated and treated with a commercial silane coupling agent, were prepared and the influence of fiber loading and the effect of chemical treatment on their thermal and morphological behavior were evaluated by SEM, DSC and TG analyses. Melt flow index (MFI) of the composites have been determined to evaluate the effects of fiber reinforcement on dynamic viscoelastic melt of the EVOH. In addition, piassava fibers characterization by SEM, FTIR, and organic and inorganic composition have also been carried out. The SEM results of the composites showed surface micrographs without microvoids and a good distribution, dispersion and compatibility between the fillers and the EVOH matrix. Concerning the piassava fibers characterization, the results showed that piassava has higher lignin content than cellulose and hemicelluloses, and around 0.7 % of ash with 52 % of silica (Si02). This high concentration of silica is consistent with the SEM analysis of the fiber that showed a large amount of ""silica rings"" encrusted on their surface.IntroductionLately, great worldwide interest has arisen in developing new technologies that enable the use of products with less environmental impact. Effort has been put into seeking natural modifier applications, particularly regarding the use of natural fibers. Special attention has been given to the use of natural vegetable fibers, because of the huge variety of species available. Such vegetable fibers are usually referred to as lignocellulosic materials [1]. This work evaluated the effects of piassava (Attalea funifera Mart.) fiber incorporation in an ethylene and vinyl alcohol copolymer (EVOH). The EVOH belongs to a family of copolymers with excellent gas barrier properties and resistance to organic compounds, which allow its application in different segments, from food packaging to gas tanks. However, EVOH is very sensitive to moisture, and in conditions of high humidity its gas barrier properties, thermal and mechanical properties are affected."

Jan 1, 2012

By Andre Thess, Oleg Zikanov

"Direct numerical simulation methods are applied to study the influence of a constant magnetic field on turbulent flows of liquid metals. The flow is assumed to be homogeneous and the problem is reduced to the classical case of the turbulent flow in a 3D box with periodic boundary conditions. The main subject of the study is the anisotropy developing in a liquid metal flow affected by constant magnetic field.To investigate the long-time evolution of initially isotropic flow the large-scale forcing is applied to maintain the flow energy at a statistically steady level. It is found that the flow evolution depend strongly on the magnetic interaction parameter (Stuart number). In the case of small Stuart number, the flow remains three-dimensional, turbulent, an approximately isotropic. At large Stuart number (strong magnetic field) the turbulence is suppressed rapidly and the flow becomes two-dimensional and laminar. Very interesting is the intermittent flow evolution at moderate Stuart number. Long periods of almost two-dimensional, laminar behavior are interrupted by strong turbulent three-dimensional bursts.The influence of a constant magnetic field on scalar transport properties of liquid metal turbulence is investigated using the simplified formulation of homogeneous flow driven by an imposed mean temperature gradient. Such a flow consists primarily of two turbulent antiparallel jets providing an effective mechanism for heat transfer. It is shown that the magnetic field parallel to the mean temperature gradient stabilizes the jets and, thus, enhances heat transfer considerably."

Jan 1, 1999

By B. Yawney

A copper-nickel sulfide concentrate was leached in water at about 2000C under oxygen pressures of about 0.35 MPa. Oxidation of sulfide to sulfate was virtually complete in about 30 minutes, resulting in greater than 95% copper and 98% nickel extractions. Leaching temperature was shown to be the most important factor affecting metal extractions. Measured rates of oxygen consumption were used to develop batch kinetic data. Mini-plant continuous pressure leaching tests agreed with batch leach results. A proposed overall flowsheet is briefly examined.

Jan 1, 1976

By Aichun Zhao, Rui Wang, Yihong Li, Yanping Bao, Yafeng Ji, Jiansheng Liu, Xiao Hu, Qingxue Huang

The slag entrapment under different conditions of 80t blowing argon ladle furnace was investigated by physical simulation. The water was used to simulate liquid steel and liquid paraffin was for slag. The processing of slag entrapment under different blowing structures was analyzed and the critical velocity and critical droplets diameter of describing it was obtained. Based on the experiments, the relationship between the interface flow velocity and the critical blowing rate CBR was deduced. In the real process, it is suggested that the bottom blowing rate is from 40 L/min to 180L/min when the interface tension is 0.12~1.2 N/m during the soft argon blowing.

Jan 1, 2016