Search Documents

By Elli Nurminen

Sulphate decomposition was studied in the conditions of a typical copper flash smelting heat recovery boiler. The aim was to determine the kinetics of the copper sulphate decomposition reactions and to find out if they are likely to take place in the process conditions prevailing in an industrial HRB. The information is essential in CFD-modelling of the reactions taking place in the boiler and for optimising the process. Thermal decomposition of sulphates was studied by thermogravimetry. The experiments were conducted with a commercial copper sulphate, a partially sulphated copper oxide and an actual process flue dust. The main variables studied were temperature and gas composition of a N2-O2-SO2-mixture. The samples were characterized with SEM, optical microscope and XRD. Temperature affected the decomposition rate strongly but the gas composition had a minor effect on the kinetics. The decomposition was fastest in the partly sulphated oxide and slowest in commercial copper sulphate. Keywords: Sulphate decomposition, flash smelting, heat recovery boiler, flue dust

Jan 1, 2004

By Nicola Baldo, Marco Pasetto

"The paper presents the results of a laboratory study, conducted at the Experimental Road Laboratory of the University of Padova, in order to verify the possibility to use different types of electric arc furnace (EAF) steel slags – in substitution of the natural aggregates – in the composition of both dense graded and porous asphalt mixes for flexible road pavements. The research has been articulated in a preliminary study of the chemical, physical, and mechanical properties of the EAF steel slags, and in the following mix design and performance characterization of the bituminous concretes, through stiffness modulus tests at various temperatures and permanent deformation (creep) tests. All the mixtures with EAF slags have satisfied the requisites for acceptance standardized for the road sector, thus resulting as suitable for use in the construction of infrastructures, moreover presenting higher mechanical characteristics than those of the corresponding asphalts with full natural aggregate. IntroductionSteel is produced industrially employing two main technologies: the integral cycle, which starts from mineral iron, and the electric cycle, which uses scrap metal. A consistent amount of the steel produced in Italy (approx. 55%) comes from Electric Arc Furnaces (EAF), which every year, alongside the steel, produce approximately 2 million tons of slag. The recycling of this waste product to produce new high-quality raw materials would reduce both the exploitation of limited natural resources and the amounts of refuse. In the European Union, 60% of slag from EAF is still today disposed of in dumps. The extremely diverse origins of scrap metal (waste from mechanical manufacturing, industrial and civil demolition, car bodywork, etc.) means that the by-products generated by the smelting, slags and ashes, contain different elements, in varying composition, also depending on the type of steel to be produced and the consequent adding of binding and melting elements during the production process. For this reason, iron and steel industry electric furnace slag - unlike the blast furnace dross utilised in cement works, which has a more uniform composition as it comes from a more standardised cycle – has been viewed in the past with some diffidence and so, at least in Italy, the possibilities of its re-use have never been fully developed."

Jan 1, 2008

By Y. H. Liu

Several foaming aluminum samples of different density were prepared in a semi-industrial scale experimental system. Their properties such as the energy absorption characteristics, mechanical properties, heat conductivity and acoustical properties were measured. The results showed that the foaming aluminum with a density of 0.5 to 0.6 g/cm3 has the best energy absorption and this makes it suitable as the ensuring bar of the automobiles and also as a cushion material for the engine. The foaming aluminum with a density of 0.25 to 0.4 g/cm3 has the best acoustical properties and heat conductivity resistance, which is suitable for the door filling material, the ceiling and the partition of the car engine.

Jan 1, 2003

By Hiroyuki Matsuura

Treatment of electric arc furnace (EAF) dusts has become an important issue from the viewpoint of the environmental protection and recycling of variable resources because these dusts contain considerable amount of zinc and lead. A new recovery process of these metals has been proposed, in which the metals in the dusts react with waste polyvinyl chloride to form metal chlorides. Therefore, it is important to clarify the physicochemical properties and behaviors of zinc, lead and those chlorides and oxychlorides. In the present study, the kinetics of chlorination of ZnO, PbO and ZnFe2O4 mainly contained in the EAF dusts were investigated at 1023 K to 1273 K with Ar-O2-Cl2 gas. Based on these results, the selective chlorination and evaporation process of zinc and lead from the mixture of Fe2O3-ZnFe2O4-ZnO-PbO was examined and the high efficiency of selectivity has been demonstrated.

Jan 1, 2006

By Cui Wang, Kexin Jiao, Qiuye Cai, Jianliang Zhang

Prolonging the campaign life of the blast furnace has been an important task for iron makers, and it has been studied for decades. Adding titanium-bearing materials is a generally agreed and effective technique to protect the blast furnace hearth. Titanium from titania additions in the burden or tuyere injection react with carbon and nitrogen and form scaffolds on the hearth surface to protect the hearth from subsequent erosion. In this article, the progress on blast furnace hearth protection of titania additions in Chinese steel companies and research institutions is investigated, and the difficulties in the operation and production, such as little effect after adding titaniumbearing materials and the property deterioration of liquid iron and slags, are analyzed. The future research for protection in Chinese blast furnace is proposed, and a comprehensive process which combines protection of titanium bearing materials with reasonable thermal balance and slagmaking regimes should be established.

Jan 1, 2015

By Wang Dawan

During the process of arsenic bearing gold concentration biooxidation, the content of chloride ion in water is a very important factor to the activity of bacteria and the oxidation of sulfide minerals. In this paper, the influence of underground mine water with different chloride ion content to the biooxidation of arsenic bearing gold concentration and the limit of chloride ion content to bacteria were summarized. These results indicated if the content of chloride ion was less than 1.2g/L, the bacteria?s ability to oxidize sulfide minerals was little affected, and if the content of chloride ion were increased to 2g/L or more, the activity of bacteria was seriously restrained, and if the content of chloride ion were increased to 4g/L, the activity of bacteria was absolutely restrained. So, as the content of chloride ion in water was cumulated to 2g/L or more in biooxidation plant, the water must be refreshed to maintain normal production.

Jan 1, 2008

By Daoxin Wu, Zhong Cao, Yan Shi, Yu Ding, Huanli Yang, Zhongliang Xiao

"2-substituted benzimidazole-zinc and 2-substituted benzimidazole-copper complexes were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. So these four complexes were prepared by 2-substitutedbenzimidazole reacting with zinc ion and copper ion, the complexes crystals were determined by IR, its thermal stabilities were studied by TG method. The results indicated that the thermal stability of 2-substituted benzimidazole-zinc is higher than the 2-substituted benzimidazole copper,and the thermal decomposition mechanism was presentedIntroductionImidazole compounds which is an important heterocyclic compound shows the important value and outstanding prospects[I-3l in field of biological engineering, medicine, and high-performance composites. It's said that imidazole compounds is an excellent new metal surface treatment[4] agent, because it has good reaction activity with metals and can form a chemical layer on the metal surface. The complexes of imidazole were main components of organic solderability preservative (OSP) in PCB producing process and affect the thermal stability of OSP film. The mechanism of imodazole combined with metal and film deposited has been reported, but the opinions about thermal stability of film have bifurcation, let alone the thermal decomposition mechanism of film at high temperature. The complexes were prepared by combining of 2- substituted-benzimidazole with zinc and copper iron, which were studied by IR and TG method, in order to get thermal stability of different complexes."

Jan 1, 2011

By Huanyu Zhang, Quanqiang Ma, Huiqing Tang

Improvement of the coke quality for blast furnace (BF) iron making by hydrothermal oxidation treatment on coke quality was investigated. Results show that, under subcritical condition, sulfur removal rate is 15% and the weight loss is 3%; under supercritical condition, both sulfur removal rate and mass loss rate increase with the increase of H2O2 concentration. In the experimental conditions, sulfur removal rate and mass loss rates were 45% and 17%, respectively. Hydrothermal oxidation treatment could reduce the CO2 reactivity of the coke and the treatment under supercritical condition is more effective. Hydrothermal oxidation treatment could improve the graphitization of the coke and smoothness of pore boundary in the coke and the treatment under supercritical condition is more effective.

Jan 1, 2016

By Viktor Ashikhin, Pavel Arkhipov, Yurii Zaikov

"Lead alloys electro-winning from chloride melts was under investigation. Impurities concentration in cathode lead is strongly depended on temperature, electrolyte composition, anode current density. The equilibrium electrode potentials of lead-antimony alloys with the various content of electropositive metal in the alloy were investigated in the wide temperature interval. Thermodynamic properties of Pb-Sb alloys containing 20-95 mol% of Pb were studied by EMF method in temperature interval 723-873K in molten mixture of potassium and lead chlorides. Partial and integral thermodynamic characteristics were calculated. Small negative deviations from Raul’s law were found. Anode processes were investigated. The lead dissolution was found to be the only process in certain interval of current densities and electropositive metal content in alloy.IntroductionAt present human race is facing the problem of pollution by lead and its compounds and also the pollution influence on population health all over the world. One of the solution ways is the recycling lead containing technical wastes by ecologically clean technologies.World scientific community pays much attention to the electrolysis of molten salts. The usage of salt mixtures, as electrolytes, discovers new possibilities in the production of metals, metal compounds and alloys. ?????????? of the electrolysis at the temperature 50 - 200 °? above the melting temperature of chosen salt mixture allow to unbreaks processes, that undergo in the pre-electrode layer. The rate of the electrodepositing of elements are much higher than in the water electrolytes. At present there are technologies developed for production of metals (Ta, Nb, Ti, Zr, Hf, Ca, Al, Mg, Be, Li and others) by the electrolysis of the melts. Electrolysis of melts might be used in order to convert different technological formations containing lead and other nonferrous metals, that produced by different enterprises. According to the level of the influence on the living organisms lead is in the group of highly dangerous substances alongside with arsenic, cadmium, mercury, selenium, zinc, etc. Toxity and ability to accumulate in the human organism are two main sources of danger for the human being."

Jan 1, 2008

By Felipe P. D. Lopes, Ailton Silva Ferreira, Sergio N. Monteiro

"Environmental issues such as global warming and water pollution are motivating fast changes in scientific and technological paradigms. Special importance is now being given to the so called environmentally friendly materials, which are renewable, recyclable and biodegradable. An example is the natural fibers with increasing industrial applications beyond the conventional uses as baskets, fabrics, ropes and carpets. In addition to traditional natural fibers, others like curaua (Ananas erectifolius) are being investigated for possible use as reinforcement of industrial composites. Since epoxy matrix is not yet incorporated with curaua fibers, the objective of this paper was to study the basic properties of epoxy composites reinforced with different amounts of curaua waste fibers. A comparative analysis aiming at the use of these composites as substitute for conventional building materials was carried out.IntroductionThis new millennium, which initiates with the 21th century, is experiencing a fast degradation of the environment by pollution and climate changes. Most of the problems are related to our methods of development associated with the use of fossil fuels and the energy intensive processing and production of synthetic materials. As a consequence, environmental issues such as global warming and ocean pollution are motivating rapid changes in technological paradigms. One relevant example is the current importance given to natural materials like the lignocellulosic fibers extracted from cultivated plants or found as industrial wastes [1]. These fibers are considered environmentally correct alternatives to substitute energy intensive conventional synthetic fibers such as carbon, glass, nylon and aramid. In addition to the renewable recyclable and biodegradable nature of the lignocellulosic fibers, the low cost and abundance in developing regions are major advantages that justify their increasing application as reinforcement of composites [2,3].In fact, nowadays, the use of natural fibers is no longer restricted to baskets, ropes, clothes and carpets. Industrial composites are introducing these fibers in large technological segments associated with car making, building construction and furniture [4,5]."

Jan 1, 2008

By Greg Dowling, Jun Ge, George Shannon, Shufeng Yang, Yongfeng Chen, Lifeng Zhang

"Inclusions in 316L stainless steel ingots poured using two different upgate designs – a traditional upgate and a swirl upgate - were investigated using SEM and ASPEX automated inclusion analysis. The main inclusions were high SiO2 inclusions, MnS inclusions and SiO2-Al2O3-CaO inclusions. More inclusions were detected at the top of the ingot than other places in vertical direction, and more inclusions were at the edge of the ingot than other place in the radial direction. With swirling upgate there were more K- and Na- bearing inclusions than that with the traditional upgate indicating possible more serious flux entrainment with the swirl upgate.IntroductionIngot casting still is very important for production of special steel grades including high carbon chromium bearing steel, thick plate, seamless tube, forgings, bars, and wire rods [1] . During the bottom teeming process, molten steel enters the trumpet and passes through the spider into the runners. Molten steel then enters the ingot mold through an upgate near the end of the runner. In the early stages of filling a mold, a mold flux bag hung in the mold were burnt and the mold flux will cover the top of the rising steel to protect the steel from being reoxidized, acting as well as act as a thermal insulator. So far, some efforts on studying inclusions characteristics in the ingot have been reported. A review paper on the control of inclusions during steel ingot casting was published by Zhang et al. [2] Zhang also studied Inclusions in bottom-teemed ingots of plain carbon steel and found that the >20µm inclusions originated from either the entrainment of mold flux of the reoxidation during teeming process. [3] The results of Nagendra and Du showed that there were more inclusions in the centre part of the ingot [4]. Eriksson et al reported that the composition of inclusions was more complex in the mold samples in comparison to the ladle samples, and more inclusions in the mold were found than in ladle because of the reaction between the mold flux and the molten steel [5]. It was reported that SiO2-CaO-Al2O3 inclusions originating from mold powder with reoxidation product Al2O3 as a part, and there were more inclusions close to the side wall than the center of the ingot in the radial direction. [6]. A more recent investigation showed that four main types of inclusions in runner samples were classified: oxides, sulfides, complex and carbon-nitrides. [7] The flow pattern in the mold during filling has been found to be an important factor regarding inclusions in the ingot. In the early stages offilling a mold, steel enters the mold through the entry nozzle at a high velocity. The effect of the resulting turbulence on the meniscus can lead to the entrainment of mold flux. Efforts have been paid over the years to find methods to reduce the velocity of the molten steel entering the mold, such as using opening angle of the inlet nozzle [8], using swirl blade at the runner [9], using a divergent nozzle combined with a swirling flow generated in the nozzle [10-11]."

Jan 1, 2012

By Maria Kuttig, Christian Ruback, Gerhard Tober, Petra Maier

"It has been demonstrated that there is a strong relationship between work hardening with various post heat treatment and cyclic deformation behavior of structural steel S275. This study contributes to a project developing a process for the complex forming of steel, which combines rolling and bending. Due to the complex geometry of the final work piece, the deformation degree varies greatly. The forming temperature, as well as post heat treatruent, influences recrystallization processes in dependence of the local deformation degree, resulting in inhomogeneous microstructure of the work piece, which affects the quasi-static and dynamic properties. Cyclic creep and hardening or softening has been monitored during constant amplitude loading at stresses near fatigue strength in normalized condition. Work hardening, stress relief or recrystallization influence the cyclic deformation behavior and produces cyclic creep effects. Cyclic softening or hardening and creep were observed to occur in parallel. To what extent these properties are noted depends on the deformation degree.IntroductionThis work is part of a research project developing a new process for the three dimensional forming of steel. For the final product the fatigue strength influenced by the forming parameters is very important. Due to its complex geometry, the formed final plate has different deformation degrees. This leads to different recrystallization behavior and heat treatruent will have different effects on the microstructure. The peak deformation degree cp of the plate will be around -0.5 what leads to the analysis using rolling from 22 mm to 13 mm of thickness. The quasi-static material properties are very important for calculating the preliminary design. However, work pieces which are cyclic loaded need fatigue tests to describe the in-service material behavior. [l] For the prediction and to guarantee the wanted life-time of the part cyclic deformation tests are important. [2, p.23-32] When it is assumed that the work piece will only loaded in cyclic tension, fatigue testing will be done from zero to a maximum force value. In preliminary tests this value is the tensile fatigue strength from a Smith diagram. During processing, here forming, work hardening takes place resulting in strengthening. Therefore, in further tests maximum load can be increased to monitor cyclic deformation mechanism in more detail. However, to study cyclic creep and hardening and softening data should be evaluate over sufficient life time and should not fracture too soon."

Jan 1, 2013

By F. G. Caballero, J. L. Gonzalez-Carrasco, S. Barrius, H. Carreon, M. Lieblich

"The grit blasting is a low-cost technique successfully used to enhance mechanical fixation of the implants through increasing their roughness. As a result of the severe plastic surface deformation, it produces subsurface effects such as grain refinement, hardening and compressive residual stresses which are generally evaluated with destructive techniques. In this research work, non-contacting and contacting thermoelectric power measurements are performed in blasted 316L VM and Ti-6AI-4V specimens using Ah03 and Zr02 particles which yield a coarse and a fine rough surface, respectively. This study correlates the microstructural changes induced by the grit blasting treatment and the limitations and advantages of each of the nondestructive thermoelectric techniques based on the Seebeck effect used to evaluate these biomaterials.IntroductionIt is well known that surface properties play an important role in metallic materials used in bio-medical applications. Since the biological response is correlated directly with surface properties it is comprehensible the intense activity in superficial modification by physics or chemistry methods in this field. Grit blasting, one of the most popular surface modification of metallic biomaterials, enhances the mechanical fixation of the implant through the increase in roughness [1-3]. Roughening is developed by bombarding the surface with a high-velocity jet of ceramic particles, being the final roughness a function of the processing parameters (pressure, distance, time, ... ) and blasting particles (nature, shape, size). As the plastically deformed surface layer tries to expand relatively to the intact interior of the specimen, residual compressive stress gradients develops perpendicular to the surface at shallow depths with a maximum value at a depth in the range of 5 to 60 µm. This surface treatment also may cause subtle variations in the subsurface material properties, such as increased hardness and grain size refinement, which are consequences of the significant plastic deformation through cold work. Blasted affected zones may extend to a depth of up to about 200 µm. The subsurface hardening and the near-surface compressive stress gradient playa beneficial role by retarding fatigue crack nucleation and further growth, ultimately extending the fatigue life of the metallic part [4]. In this work, two non-destructive thermoelectric techniques (NDTT), the non-contacting and contacting thermoelectric power measurements were used to analyze the subsurface induced changes on blasted Ti-6AI-4V and 316L VM specimens using Al2O3 and Zr02 particles. Detailed information on the microstructural induced effects and subsurface mechanical properties were published elsewhere [5-8]. Here the nondestructive evaluation of the involved microstructural changes is used to assess the global subsurface damage. Advantages of using nondestructive techniques during manufacturing are envisaged."

Jan 1, 2012

By Björn Hinzel, Joachim Rösler

"The most important characteristic of open-pored metals is porosity, since it enables all of their functional applications as filters or sound absorbers. Due to the notch effect of the pores, mechanical properties of porous metals are better than the ones of comparable structures made of polymers or ceramics. Consequently, only open-pored metals can be used in aircrafts to reduce flow noise or noise resulting from the core engine by acoustic absorption. Absorption properties depend highly on pore size and porosity of the material, which must be characterized as precisely as possible in order to analyze the correlation between morphology and noise reduction performance. Here, a line segmenting method is explained in order to characterize pore size and porosity of absorber materials using image processing based on two dimensional microscopy images, including sample preparation and specification of the set-up. Then, the influence of the pore structure on the measured absorption behavior is discussed. Finally, the correlation of acoustic behavior, pore morphology, and porosity is outlined.IntroductionSignificant noise loads affect everyone causing anxiety, depression, insomnia and other effects which impair health and productivity [1],[2]. Due to the rising number of flights and aircrafts, air traffic noise increases dramatically. To counter this development, various approaches have been developed to reduce the different noise sources resulting from airframe, jet or engine [3],[4],[5],[6]. One approach to reduce this noise is the application of noise reducing liners in the hot gas path [7]. This is especially important, since the engine is becoming the dominant noise source of modern airplanes during take-off [8]. Due to the elevated temperatures and high fatigue loading in this part of the aero-engine, conventional passive absorber materials cannot be used. Polymers would not be able to bear the heat and ceramic fibers would crack under the mechanical loading due to the notch effect. Consequently, this study focuses on metals with open pores, which can resist elevated temperatures and fatigue loading and additionally resemble geometrically conventional passive absorbers. Based on the production processes, e.g. sintering of metal fibers [7], powder processing using a foaming agent [9], coating of polymer foams [10], or using melt infiltration techniques [11], the characteristic dimension of the porosity is usually in the range of 0.01-10mm. In this work, sintered metals and metal sponges are analyzed after the theory of sound absorption is briefly outlined. Then, measurements of the acoustic absorption of metal sponges and sintered metals in an impedance tube are performed. To understand and predict the acoustic properties of metals with open porosity, it is necessary to characterize the materials as precisely as possible. This is explained in detail using a line segmenting technique, followed by a discussion of the connection of pore characteristics and acoustic absorption. Finally, a conclusion is given."

Jan 1, 2012

By Akram Salah Eddine Belaidi, Lakhdar Azzouz, Benchaa Benabed

"The dunes sand is a material of a large availability in Algeria. This material is practically unexploited. The introduction of this material as a new element in the construction can be more relieve the domain of building, and contribute to the development of the southern regions of Algeria, which are very rich in this material. The main objective of our work is to exploit a largely available material in the Algerian south which is the dunes sand, as a material of construction in the region of Laghouat.In this study, first we investigated the effect of the curing environment and the nature of the sand on the mechanical properties of the mortar, such as; flexural and compressive strengths. Then after, we studied the durability of the mortar under cycles of wettingdrying and the chemical attack of sodium sulfate (Na2SO4 5%).According to the results, we note that the mortar of the sand mixes (river sand plus dunes sand) present the best mechanical performances under different environment of curing. In addition result of durability studies put forward that the mortar of the sand mixes is more resistant to the sulfates attack."

Jan 1, 2008

By R. S. Tahautdinov, A. N. Posazhennikov, V. V. Bastrygin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Samples of iron ore and carbon reductant were chemically and physically analyzed. Green pellets were processed via a lab tube furnace to simulate RHF conditions. The nuggets and slag were chemically analyzed. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2011

By R. M. Westcott

A two-electrode, direct current, slag resistance furnace (SRF) has been constructed and operated to selectively reduce the zinc and lead contents of non-ferrous slags. The experimental SRF is equipped with multiple methods of gas/solids injection for both mixing and reaction. A computer is used to position the electrodes and for data acquisition. A geometric factor correlation was previously developed at Columbia University for calculating the electrical resistance on the basis of furnace geometry and slag conductivity. The experimental SRF was used to test this correlation.

Jan 1, 1994

By T. Yoshida

The Ni-MH (nickel metal hydride) rechargeable battery was developed several years ago. Its higher electrochemical capacity and greater safety compared with the Ni-Cd rechargeable battery have resulted in very rapid Increase in its production. The Ni-MH rechargeable battery consists of Ni. Co and rare earth metals, so that recycling is important to recover these valuable mineral resources. In this study. a basic recycling process for used Ni-MH rechargeable batteries has been developed, in which the Ni. Co and rare earth elements are recovered through a combination of mechanical processing and hydrometallurglcal processing.

Jan 1, 1995

By E. V. Redin

"The Bakal (South Ural, Russia) deposit of iron ore bearing iron carbonate (siderite) with the capacity of more than 1 billion tones belongs to the MMK. This ore cannot be fully processed via blast furnace technology because of high content of MgO. According to the investigations carried out in the USA and Japan in 1999-2004 the ITmk3 (Ironmaking Technology mark three) RHF technology is a breakthrough in Ironmaking. Four iron ore types (hematite, magnetite, high and low Al2O3/SiO2) were tested. Reduction, melting and slag removal can be achieved in just 10 min. The main objective of the investigation is to establish optimum operation conditions for the production of iron nuggets from iron carbonate bearing ore via the ITmk3 by means of the lab scale testing. Green pellets were processed via a lab tube (chamber) furnace to simulate RHF conditions. This preliminary test work provides valuable information which may be used for large-scale testing in a commercially sized RHF.IntroductionThe ITmk3 process upon which this paper focuses was developed by Kobe Steel in its research facilities in 1996 [1]. After pilot testing at Kobe Steel’s Kakogava Works in 1999-2004 the pilot demonstration plant was built and operations were successfully carried out by Mesabi Nugget joint venture in 2002-2004. Steel Dynamics has committed to building the commercial plant at the Mesabi Nugget site in Hoyt Lakes (Minnesota). Only 4 iron ore types (hematite, magnetite, high Al2O3/SiO2 and low Al2O3/SiO2), as well as 4 coal types with range of volatility, ash and fixed carbon were tested. Results were consistent with nugget characteristics confirming ITmk3’s flexibility with respect to raw material inputs. At the same time, no research in the field of nugget from iron carbonate bearing ore with high content of MgO has been done. Such kind of iron ore is restricted for charging into the blast furnace due to contamination of MgO. The reason for restriction is the limitation of load of MgO in the blast furnace. If a lot of MgO enters the blast furnace, slag becomes viscous. The viscous slag is obstacle for stable operation of the blast furnace."

Jan 1, 2012

By W. G. Davenport

Most pre-t 988 Outokumpu flash furnaces were built with blast heaters. Many continue to use them. Blast temperatures in these smelters· are typically 400 to 700 K (Table 2. 1) This chapter: (a) shows how hot blast is included in our calculations (b) evaluates the effects orhot blast onauthothermal65% Cu matte production.

Jan 1, 2001