Search Documents

By O. Durand

The Cerro Verde Hydrometallurgical Plant, located at Arequipa in the southern part of Peru, started its operation in 1977 with a design capacity of 33,000 MT/year of copper cathodes. The plant has treated 61,055,000 MT of ore mainly oxides with a content of 1.01% total copper and 0.67% of soluble copper. The leaching plant has three pads that produce 4.0 gpl copper solution. The solvent extraction plant has four trains with three extraction stages, two stripping stages with a single mixer in all stages. The mixer-settlers are 316 stainless steel and the pumps are vertical turbines. The flowrates of 1,300 gal/mil of aqueous and 1,300 gal/min of organic at a 1/1 ratio. The electrowinning plant contains 208 commercial cells and 18 starting sheet cells. Each cell has 47 anodes and 46 cathodes. In addition to describing the hydrometallurgical plant, this paper also mentions efforts directed at reducing costs and improving operations. The initial results from leaching secondary sulfides, which started October 1985, are also discussed.

Jan 1, 1987

By Bo Björkman

A controlled dust generation whereby the dust generated would be enriched with specific metals would considerably facilitate the possibilities of recovering metals from such dusts. A basic understanding of the dust forming mechanisms is of fundamental importance to achieve a controlled dust generation. The present study deals with dust formation in a copper converting process. Dust samples collected from various places in the gas cleaning system were characterised for chemical and mineralogical composition using chemical analysis as well as microprobe analysis. Thermodynamic calculations were used to predict the formation of chemically formed dust at various temperatures and amounts of leakage air to the gas system. The results show that a separation of mechanically formed dust. e.g . Si0:2. Cu and chemically formed dust. e.g .? Ph, Zn, As, Bi. could, to some extent, be obtained due to their different particle sizes. A selective condensation of Pb, Zn and As at various temperatures could. according to thermodynamic calculations, he possible at high temperature. A selective condensation of metals requires an airtight gas cleaning system or a gas cleaning system with a limited amount of leakage air in order to maintain the desired temperature level.

Jan 1, 1996

By A. Deneys

An experimental technique has been devised for studying the reaction kinetics of the reaction: ZnO + 2Fe0 = Zn(g) + Fe203, by which zinc evolution can occur from a molten slag bath in the absence of a carbonaceous reductant. When studying the reaction kinetics by heating from room temperature, solid state reactions and poorly defined melting points may obscure the starting point of the reaction. In order to eliminate this problem, an experimental technique was devised whereby two molten slags could be melted independently, and then mixed, to provide a well defined starting point from which to begin taking measurements. Two crucibles were mounted in a vertical reaction cylinder. The upper, mild steel, crucible had a bottom pouring plug which was sealed by a steel stopper rod. A fayalite mixture was contained in this crucible. The lower crucible contained an A12O3-CaO-SiO2-ZnO solution. Once the two slags had been melted, the steel stopper rod was removed from the upper crucible. The upper, reduced slag (fayalite in equilibrium with the upper steel crucible), drained into the lower crucible where the two slags were mixed by submerged argon stirring. Dip samples were taken to measure the zinc content of the final mixture as a function of time. The experimental procedure will be described, as well as results of experiments which were conducted on synthetic slags. The system investigated was similar to the lead blast furnace slag which is produced by the primary lead smelters of Missouri, USA.

Jan 1, 1997

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of alloying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an alloy.

Jan 1, 2003

By Neng-Wen Yu, Shau-Jun Zhu, Ji-He Wei

The desulfurization process by powder injection and blowing in the RH refining of molten steel and its mechanism have been considered and analyzed. Based on the two-resistance mass transfer theory and the mass balance of sulfur in the system, a kinetic model for the process has been developed. The related parameters of the model, including the mass transfer coefficients and the effective amount of powder in the molten steel being treated for desulfurization, have been more reasonably determined. Modeling and predictions of the process of injecting and blowing the lime-based powder flux under assumed operating modes with the different initial contents of sulfur and amounts of powder injected and blown in a RH degasser of 300 t capacity have been carried out using the model. The relevant circulation rate of the liquid steel and the powder injection and blowing rate were taken to be 100 t/min and 150 kg/min, respectively. The initial contents of sulfur in the liquid steel to be treated and the amounts of powder injection and blowing were respectively assumed to be 0.007, 0.006, 0.005, 0.004, 0.003, 0.002 mass-% and 10, 8, 6, 5, 4, 3 kg/t-steel. The total treatment time for desulfurization under each mode was set up at 24 min, equivalent to eight circulation cycles of the liquid steel to be treated. The results indicated that the predictions made with this model are in good agreement with some data of the industrial experiments and practice. Injecting and blowing the lime-based powder flux with the composition of 85 mass-% lime (CaO) + 15 mass-% fluorspar (CaF2) of 3-5 kg/t-steel, it is possible to decrease the sulfur content in the molten steel to ultralow level below (5-10)x10·4 mass-% from (60-80)x 10·4 mass-%. The total treatment time needed will appropriately be 12-20 min. Intensifying the powder injection and blowing operation and increasing the circulation rate of the liquid steel may effectively' raise the rate of the process in RH refining. The model may be expected to offer some useful information and a reliable basis for determining the reasonable process parameters and help in optimizing the technology of desulfurization by powder injection and blowing in the RH refining of molten steel.

Jan 1, 2000

By Florian Kongoli

Non-ferrous smelting slags .can contain magnesia, which substantially increases the liquidus temperature. One option to counter this increase is to flux with calcia. In this work, experimental liquidus measurements including new measurements on industrial slags have been compared with a FACT-based thermodynamic model, which predicts the liquidus surface of multi-component iron silicate smelting slags containing both magnesia and calcia. The predictions, which agree well with experimental results, are summarized in both isothermal and non-isothermal diagrams to give a quantitative description of the liquidus surface.

Jan 1, 1998

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

The cleaning of copper containing fayalite slag using a CuFe alloy was studied under an oxygen pressure ranging from 10-7 to 5 X 10-11 atm at 1200º c. The reduction of copper from fayalite slags by Cu-Fe alloys was found to be very effective. For example, at a P 02 of 10-7 atm, the copper content in the slag was reduced from 4.1 to 0.402 wt. percent after 90 min. of reaction time using a Cu- 5.27 wt. percent Fe alloy. The copper reduction rates were found to be independent of P02 in the gas phase when using Cu-Fe alloys which exhibit an iron activity of greater than 0.4. A mechanism for slag c1eaning is proposed based on the concept that the Cu-Fe alloy lowers the oxygen potential of the slag according to Eq.1 1, fol1owed by the reduction of cuprous oxide by wustite as shown in Eq.2. Here X represents element X in the alloy phase while (X) represents the element in the slag phase. The copper and iron transfer behaviour obtained in this study are explained by a ?Stepwise equilibrium model.

Jan 1, 1985

By Guanghui Li

In the paper, the recovery technology of gallium from zinc-leaching residue by cold-bonded coal-based direct reduction process following magnetic separation was developed. The results show that the scattered metal Ga can be concentrated obviously after the reduction of zinc-leaching residue briquette and magnetic separation of reduced product. At the same time, the volatilization of Zn in the residue is enhanced during the reduction. When the residue, bear¬ing 18.60% Zu.21.18% Fe and 527 g/t Ga, was reduced with coal at 1100°C for 150 min, the results of Zn volatilization of 9842% and Ga recovery of 89. 10% were obtained in reduction. After magnetic separation of the reduced product, the concentration of Ga in sponge iron is 2164 g/t, and the separation recovery of Ga reaches 92.42%. The enriched mechanism of Ga during reduction -separation process was studied by using electron microscope, scanning elec¬tron microscope, energy spectrum and mineralogical analysis. The investigations show that there is no formation of independent phase of Ga during reduction process. The Ga occurs mainly in metallic iron phase (the concentration of Ga in metallic iron phase is 0.04%-0,4%), in addition, there exists a little Ga in poorly crystalline sulphide (o.08%-0./5Y& Ow). But Go does not exist in most of glass and silicate phase. The affinity of Ga for metallic iron is the enrichment basis of Go in reduction, and it is also in favor of recovering Go during magnetic separation. Key Words: Gallium Zinc-leaching Residue Cold- Bonded Direct Reduction

Jan 1, 2003

By Mehdi Asadi, Heinz Palkowski

"In recent years, the increased demand for advanced high-strength steels (AHSS) mainly had been driven by the need of the automotive industry to reduce weight and to improve safety. Beside good ductility and high strength, those steels have a high bake hardening (BH) effect, giving additional contribution to the strength of structural parts, subjected to the paint baking process. In this paper we concentrate results gained for hot rolled dual phase (DP) steels.For the simulation of changing process conditions within the final hot rolling the specimens were hot deformed using different schedules of temperatures and reductions, selected according to the non-recrystallization temperature (TnRX). It was possible to refine the DP steel structure by control-ling the deformation temperature and the amount of strain below TnRX during the thermo-mechanical controlled processing (TMCP). This structure refinement resulted in an improvement of the strength and BH behaviour. A wide spectrum of mechanical properties could be obtained depending on the different hot deformation schedules. The best strength and BH levels were recorded for the deformation below TnRX at the highest amount of strain.IntroductionDP steels are characterized by a good formability, high strength and a good compromise between strength and ductility [1]. Moreover, the DP steels exhibit a continuous yielding behaviour, low yield point and a high strain-hardening coefficient [2]. Furthermore, the DP steels often show a large potential for bake hardening (BH). BH refers to the increase in yield strength as a result of the paint baking treatment of the shaped auto-body parts. The primary mechanism that causes the additional strengthening is the immobilization of dislocations by the segregation of interstitial atoms, known as classical static strain aging [3]. The increase of strength thus achieved allows a further reduction of sheet thickness and improves the crash safety and the dent resistance. The BH of special steel qualities is technically used in DP, where e.g. the increase in strength is realized in the final heat treatment [4]. Previous own investigations [5-6] stated that the BH effect of DP is much stronger than that one for conventional BH steels."

Jan 1, 2012

By Anish Kumar

Keywords: Ultrasonic velocity, Poisson?s ratio, Elastic constants A new correlation has been established between two independent elastic properties, ultrasonic shear wave velocity and Poisson?s ratio, in a wide variety of isotropic solid materials, such as pure metals, ceramics, polymers and intermetallics. It has been shown for the first time that Poisson?s ratio decreases with increase in elastic moduli, E & G and ultrasonic velocities. This new correlation between two independent elastic constants may lead to the reduction in independent elastic constants for isotropic solid materials from two to one, at least for a given alloy system with different microstructural conditions.

Jan 1, 2005

By Louis J. Mittoni

"It is well known that gas injection systems can exhibit a wide range of dynamical behaviours, ranging from linear periodic bubbling through to highly complex turbulent jetting. Recently, it has been observed that an important intermediate regime exists under certain system conditions, where the dynamics are complex in nature yet predictable for short time periods. This paper reviews the evidence to support the above hypothesis, and discusses the invariant quantitative measures such as density, return maps, Lyapunov exponent and dimension which may be used as pattern recognition features in a mOnitoring and control strategy.INTRODUCTIONThere has been a great deal of research on the submerged injection of gases into liquids. This interest is primarily due to the large number of applications in the pyrometallurgical and chemical engineering industries. Gases are typically injected into liquids to achieve goals such as heat and mass transfer, or physical mixing and agitation. Only recently though has the possibility of using the evolution of the gas dynamics as a probe to internal system conditions been raised [1, 2].At very low gas injection rates and small upstream chamber volumes, gas normally disperses in the form of stable bubbles of constant volume [3]. With increases in gas flow rate, the dynamics become more complex, bifurcating into double bubbling, multiple bubbling and complex coalescence behaviour. Irregularities measured in pressuretime series acquired upstream of the injection port under these complex conditions have usually been treated as bothersome noise or contamination to be filtered from the signal and ignored in the analysis. These irregularities, however, may contain physically interesting and useful information on the system from which they were produced if the system may be classified as deterministically chaotic [4]."

Jan 1, 1996

By Jian Li, Tiejun Chun, Jian Pan, Deqing Zhu, Vinicius Mendes

"A study of the coal-based direct reduction behaviors of composite binder magnetite pellets was carried out in a simulating coal-based grate-rotary kiln process. It is shown that preheated pellets possess much better reducibility than fired oxide pellets: 40 min are required for preheated pellets to reach over 90% metallization degree compared to 100 min for fired oxide pellets. The compressive strength of preheated pellets decreases dramatically at the earlier stage of reduction, climbs quickly after reducing for 30min and achieves a high value at the end of reduction. However, the compressive strength of metallized pellets from reducing of fired pellets is much lower, more cracks and fractures being formed. In the preheated pellets, crystallite of metal iron is coarse. In the oxide pellet, a large number of interconnected crystals of metal iron are formed inside pellets, and pellet structure is very compact.IntroductionDirectly reduced iron is an excellent feed in electric arc furnace (EAF) steelmaking, and possesses low tramp element content and steady component. It is generally preferred in the production of high quality steel [1-3]. Nearly 64.44 million tons of DRI were produced in 2009 over the world, over 80% of which were produced by gas-based processes, the left by coal-based processes. However, the DRI capacity was only 600 thousand tons in China in 2009. The EAF steel production has exceeded 40 million tons annually, and most of EAF operate on hot metal as feed [4]."

Jan 1, 2011

By Phillip A. Armstrong, Charles A. Lewinsohn, John H. Gordon

"This paper describes the opportunity offered by employing systems based on mixed conductive ceramics, in particular, ceramics conductive to oxygen ions and electrons, in reducing CO2 emissions from metallurgical production. Membranes based on these mixed conducting properties enable commercial viability of several attractive metallurgical processes. One of these processes utilizes modular, ceramic-membrane structures for the generation of pure oxygen, in tonnage quantity. The membrane-based systems offer significant capital savings and operating efficiencies in various metallurgical processes. The current status of this technology is summarized below.IntroductionCryogenic oxygen supply technology is currently the state-of-the-art for applications that require large quantities of oxygen (hundreds to thousands of tons per day). Cryogenic technology, however, requires substantial energy inputs and, hence, adds significant costs and emissions to processes. Furthermore, cryogenic oxygen supply technology is mature and there is relatively little potential for substantial capital cost reduction or efficiency improvement in coming decades. Non-cryogenic technologies offer a means to reduce the environmental footprint and cost of the oxygen supply facility in various applications.Ion Transport membranesCommercially available non-cryogenic air separation technologies, such as adsorption-based and polymeric membrane-based methods, do not afford the economies of scale that the cryogenic distillation enjoys. Therefore, industrial gas industry researchers began searching for alternatives to the relatively inactive and unselective polymeric membrane materials available. In the late 1980’s, Air Products began developing a new class of highly selective membrane materials with exceptionally high activity for oxygen transport. The materials constitute a class of oxide ceramics, and conduct both oxygen (as oxygen ions) and electrons in the same membrane, separating oxygen from air electrochemically. Numerous detailed process economics studies have shown that, based on these ion-transport membranes (ITM’s), the cost of oxygen can be reduced by approximately one-third relative to that obtained from state-of-the-art cryogenic oxygen supply technology, through a combination of capital cost savings and efficiency improvements. [1,2,3]"

Jan 1, 2008

By Markus A. Reuter, Robert Matusewicz

"Consumer products are a complex man-made mixture of sometimes in excess of 50 elements. In order to recover these complex mixtures of elements either as metals, compounds or energy requires versatile technology in physical separation but also smelting and energy recovery. This paper explores this by referring to the innovative application of Top Submerged Lance (TSL) technology and associated theoretical and environmental aspects to process (recycle) post consumer materials and industrial intermediate products and residues. A diversity of applications has been tested in Ausmelt’s pilot plant in Dandenong and many have gone to commercial scale globally. This paper reviews the varied applications ranging from e-waste recycling, lead and NiCd battery recycling, metals recovery from slags, zinc leach residue processing, electric arc furnace (EAF) dust, Municipal Waste Incinerator bottom ash processing, carbon containing residues such as retort ashes and spent pot liner from the aluminium production process as well as use of the technology for materials such as automotive shredder residue (ASR) and plastics. Introduction The modern resource cycle is a link between primary production of metals linked to the recycling of post-consumer goods. The sometimes complex combinations of materials and metals in consumer products such as televisions depicted by Figure 1, does require a range of technology to recover materials, metals and energy for reuse and/or recycling in an economically feasible as well as environmentally friendly manner."

Jan 1, 2008

By J. Bostjancic

As wastewater discharge regulations become more stringent, power plants, manufacturing plants and other industrial sites are looking for ways to reduce makeup water requirements and to recycle and reuse as much wastewater as possible. In some cases, environmental regulations require zero liquid discharge, meaning all wastewater must either be retained on site or reduced to solids for disposal off site. Zero liquid discharge or "closed-loop" wastewater treatment systems using evaporators and other process equipment have been well-accepted in recent years. Often overlooked is the fact that zero discharge is not just the latest fashion--many commercial zero liquid discharge systems have been in operation since the mid-70's. This paper will give specific examples of zero liquid discharge operations from 1974 to the present, showing how evaporation equipment and processes have changed to meet the requirements of industry and environmental regulations.

Jan 1, 1996

By Rodney L. Williamson

Optimal estimation theory has been applied to the problem of estimating process variables during vacuum arc remelting (V AR), a process widely used in the specialty metals industry to cast large ingots of segregation sensitive and/or reactive metal alloys. Four state variables were used to develop a simple state-space model of the V AR process: electrode gap (G), electrode mass (M), electrode position (X) and electrode melting rate (R). The optimal estimator consists of a Kalman filter that incorporates the model and uses electrode feed rate and measurement based estimates of G, M and X to produce optimal estimates of all four state variables. Simulations show that the filter provides estimates that have error variances between one and three orders-of-magnitude less than estimates based solely on measurements. Examples are presented that verify this for electrode gap, an extremely important control parameter for the process.

Jan 1, 2001

By Kazuteru Tozawa

Surface tension, density and viscosity coefficient of acidic copper sulfate solutions simulating electrolyte solution for electrolytic production of copper have been measured and are summarized as a function of the solution composition and temperature. Nickel sulfatc is taken to be a representative coexisting sulfate that affects the physical properties of the copper sulfate electrolyte solution. The sulfates in the solutions, including sulfuric acid, increase the physical properties under consideration. Gelatin, representing organic additives for electrolyte solution, was found to sensitively affect the surface tension of the solution at low concentration of up to 200mgIL. The surface tension was markedly lowered by the addition of gelatin and the increasing concentration of gelatin led to a more pronounced decrease in the observed values. The surface tension gradually increases with time after addition of gelatin and the increase is enhanced by higher acid concentration and higher temperature. The observed change in the surface tension is considered to reflect the preferential adsorption of gelatin to the bubble-solution interface and the decomposition of gelatin due to hydrolysis to form various molecules having smaller molecular weights.

Jan 1, 2003

By Wenjun Duan, Zongliang Zuo, Qingbo Yu, Qin Qin, Junxiang Liu

Moving bed has been widely used in the field of heat and mass transfer and reaction between solid particles and gas. In order to enhance the heat exchange coefficient, there will be tube banks inserted in the moving bed. In the process of drying ammoniates particles or heat recovery from high-temperature particles with moving bed, the particles flow behavior around the tube banks is significant. In this paper, the particles flow behavior around the tube banks is investigated, and all the results can provide guidance for the design and operation of a moving bed.

Jan 1, 2016

By Musa Karakus

The sedimentary iron ores of Alsace-Lorraine, France have very high phosphorous contents that average 0.7% and are as much as 2.19% P. Ores from the Tucquegnieux and Joeuf mines have been studied by cathodoluminescence microscopy, X-ray diffraction, scanning electron microscopy, and electron microprobe analysis in order to fully characterize the mineralogy, size, shape, and distribution of the deleterious phosphate grains. The phosphorous occurs as collophane, a carbonate fluorapatite, in ten morphological forms, most abundantly as microcoprolites, but also as intraclasts, concentric layers, and cortices in ooids, phosphate replaced ooids and bioclasts, phosphatiC shells, fossil infillings and internal molds, fish teeth, phosphatiC laminae, and cements between the goethite ooids. About 95% of the phosphate grains are sufficiently large that relatively fine grinding fol'lowed by reverse flotation would be expected to be effective in significantly diminishing the phosphorous content of the concentrates.

Jan 1, 1989