Search Documents

By M. Patel, A. W. Piper, R. A. Forsdick

"Lead bullion is refined in kettles to remove the contained impurities such as copper, antimony, silver and bismuth. These impurities are removed sequentially by the addition of one, or more, reagents to the bath. Impurity elements react selectively with the reagents to form a dross layer on the surface that is subsequently removed for further processing. Mixing the lead bath using specific impeller designs, which form a vortex to ensure that good contact takes place, carries out the reactions. It is important that the mixing is controlled to achieve the optimum bath conditions and hence good dross grades.This paper presents initial modelling work on the kettle refining process using both physical modelling (Water Models) and mathematical modelling (Computational Fluid Dynamics - CFD). Comparisons between measured plant data and simulation results are given.IntroductionThe refining of lead bullion takes place in hemispherical kettles of varying sizes. It is normal practice to remove the impurity elements sequentially, by the addition of reagents, which selectively react with the impurity element. The impurity element forms a dross layer on the surface, which can be removed for subsequent processing at the end of the reaction period.All the refining stages in the production of lead and lead alloys involve mixing the lead bath, although different conditions are required for each stage. At Britannia Refined Metals mixing is achieved using either 3 or 4 angled or flat blade impellers, which generate a vortex in the central region of the kettle. However, throughout the industry a wide range of mixer types are used which are all trying to achieve the same result."

Jan 1, 1999

"An experimental study has been performed to investigate the dispersed phase holdup induced by a high-strength submerged gas injection in a bottom blown air-stirred one-seventh water model of CLU (Creusot-Loire Uddeholm) reactor using two different tuyere configurations. The air flow rates varied from 0.00599 m3/sec to 0.01312 m3/sec. In these series of experiments, water height and kerosene height were kept constant at 0.23m and 0.02m respectively. The dispersed phase holdup was determined at various gas flow rates, and tuyere orientations by using water and kerosene.The dispersed phase holdup increased with gas injection rate and decreased with vertical distance from the original interface. At constant gas flow rate, as the vertical distance increased in the centerline, off-center configuration of nozzles displayed higher values of the dispersed phase holdup than those of the center configuration. The variation of the dispersed phase holdup with the dimensionless axial distance and the gas injection rate was correlated by using the Modified Froude Number. The experimental values of the dispersed phase holdup were found to be in good agreement with the calculated values obtained from the correlation equations."

Jan 1, 1999

By M. I. Zinigrad

A model of an ideal associated solution is presented. This model takes into account the existence of complexes of various compositions, sizes and geometries and allows calculating thermodynamic properties and phase diagrams of binary alloys. The model has been used formerly to calculate thermodynamic parameters and the position of the liquidus line for binary eutectic systems and also those having a stable compound in the solid phase. In all the cases the model parameters were not adjusted rather estimated from melting temperatures of the components. The recent studies dealt with the influence of arbitrary-stoichiometry associates on the equilibrium thermodynamic properties of liquid alloys. The application of the model to eutectic systems and systems having an unlimited solubility in solid and liquid states close to liquidus has been considered. It was shown that if the difference in melting temperatures of the components was small, different types of fusibility diagrams were possible: eutectic diagrams, cigar-shaped diagrams or diagrams with upper or lower azeotropic points. Peritectic transformations could take place when the difference in melting temperatures of the components was large. The present work is devoted to calculation of phase diagrams and thermodynamic properties of binary systems on the basis of chrome.

Jan 1, 2006

By G. Kugler, M. Tercelj

"The use of the up-to date light alloys and their development are in the sharp ascent especially in transportation industry. In the last years the use of the magnesium alloys for the various purposes was strongly increased. The aim of present research was to study the influence of solidification rate on hot workability and on obtained mechanical properties of AM60 magnesium alloy. The study was also focused on possibility to omit prior homogenisation process which would result in cost reduction. The solidification of gravity cast alloy has been investigated with various methods of the thermal analysis: in situ simple thermal analysis and simultaneous thermal analysis. In order to reveal optimal hot working conditions the deformation behaviour was studied in the temperature range 200-450°C and strain rates between 0.001-lOs-1. Mechanical properties have been studied with tensile and impact toughness testing.IntroductionIn recent years, the increased demand for magnesium alloys has been mainly driven by the need of automotive and transportation industry to reduce the weight, as this is the most important parameter to reduce the energy consumption. Beside their very low weight in comparison to other metals, the magnesium alloys are characterized by good machinability, corrosion resistance and good mechanical properties, and can thus compete with aluminium alloys and for some applications even with steels. Due their decreased workabilty they are typically used as cast alloys, but in recent years also the research of their wrought state has become more extensive [1-7]. Decreased hot workability of magnesium alloys originates from their hexagonal close-packed structure. One of the most popular magnesium alloys with great potential for many applications is AM60 (MgA16Mn), which is predominately used for casting. But its application could be increased if the mechanical properties, could be improved. This can be done by hot working. Namely it is well known that wrought microstructure is characterized by better mechanical properties in comparison to as-cast state. On the other hand due to its low hot workability the homogenization process is required prior hot deformation, which results in increased production costs. Thus the aim of the present research was to study the influence of solidification rate on hot workability of AM60 alloy in order to improve its mechanical properties and to check the possibility of producing near-net-shape casting products omitting homogenisation process by employing small additional deformations after casting. Within the framework of this research the solidification of gravity cast AM60 alloy has been investigated with various methods of the thermal analysis."

Jan 1, 2011

By Yuhua Pan

Generic mathematical models have been developed for simulating heat transfer in two types of slag resistance heating electric furnaces for sulphide smelting: i) six-electrode-in-line rectangular furnaces and ii) three-electrode circular furnaces. The models are based on three-dimensional steady-state heat transfer of conduction, convection and radiation. Solidification of liquid slag into solid slag by water-cooling units, for use as freeze lining of furnace walls, is also considered in the models. The developed models are capable of providing predictions with reasonable accuracy for electric furnaces on 1) temperatures in slag, matte, cooling water, freeze lining and other solid regions as well as temperatures at various fluid/solid interfaces, 2) freeze lining thickness, 3) furnace smelting rate and 4) furnace heat loss rate. These computer models are built into executable application programs that are very efficient, with execution time less than one second, and can be easily portable to most computing platforms. This paper describes, as an example, the modelling results on heat transfer in six-electrode furnaces. The major modelling results show that in six-electrode furnaces uniform electric power inputs to the electrodes likely lead to low temperature regions close to slag and matte tapping ends of the furnaces, and the power input and the formation of air gaps between freeze lining and cooling units have significant influences on the thickness of freeze lining maintained by the cooling units.

Jan 1, 2006

By P. D. Nolan

Smelters operating under pollution control orders have become increasingly dependent upon the reliable operation of sulphuric acid plants and no factor affects the long term reliability of those plants more than efficient gas cleaning. The sources and characteristics of contaminants in smelter of fgases and the conventional approaches to removing these contaminants to accepted levels are discussed. New technology is described which offers advantages of lower capital cost, lower operating cost and reduced space requirements over the conventional approaches. This new technology has been developed by LAB s.a. and is licensed for metallurgical gas applications by Chemetics International Company.

Jan 1, 1983

By Seshadri Seetharaman, Nurni N. Viswanathan, Haijuan Wang

"In order to make the stainless steel making process efficient and environment friendly, it is essential to minimize the loss of chromium to the slag phase. With a view to investigate the advantages of using CO2 to attain moderate oxygen partial pressures in the oxidant gas during the decarburizations of stainless steel, the present experiments were carried out to understand the oxidation kinetics of Fe-Cr alloys and Fe-V alloy with gas mixtures containing CO2. In the present work, the oxidation behavior of Fe-Cr and Fe-V was examined by thermogravimetric analysis (TGA). Various mixtures of O2 and CO2 were used as the oxidant gas and the oxidation rate was followed by the weight changes as a function of time.The experiments demonstrated that the oxidation rate is independent of temperature at present experimental situation, but has strongly related to the Cr-content of the alloy as well as the oxygen partial pressure in the oxidant gas mixture. The wetting of alumina by the iron drop and the change of the drop shape during the course of the oxidation were investigated by X-ray radiography."

Jan 1, 2010

By Xue Ping

Sm2Fe17 alloy is an important precursor for the preparation of Sm2Fe17Nx magnet, which possesses a higher Curie temperature, larger anisotropy field, better resistance to oxidation and thermal stability. In this paper, the wet chemical co-precipitation was developed for synthesis of the Sm-Fe alloy oxide precursor. Based on the principles of simultaneous equilibrium and mass balance, a series of thermodynamic equilibrium equations of Sm(III)-Fe(II)-NH3-C2O4 2--H2O system at ambient temperature were deduced theoretically and the thermodynamic diagrams of lg[M2+]T (M=Sm, Fe) versus pH at different solution compositions were drawn. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH value, reactant concentration, reaction temperature and aging time, etc. It is found that by precise control of the process, the Sm-Fe alloy oxide precursor was synthesized with fine crystallization and special size &size distribution.

Jan 1, 2008

By C. J. N. Buisman

THIOPAQ technology developed and marketed by PAQUES Bio Systems in Balk, Netherlands, has been successfully used at commercial scale at the Budelco zinc refinery in the Netherlands for the treatment of contaminated groundwater since 1992. In essence, THIOPAQ technology consists of two biological process steps in series: sulfate reduction to hydrogen sulfide (anaerobic) and sulfide oxidation to elemental sulfur (aerobic). The biogenic sulfide produced can be employed for the chemical precipitation of metals in solution either inside the anaerobic reactor or in a separate vessel. Since the solubilities of most metal sulfides are much lower than of their respective hydroxides, considerably lower effluent metal concentrations can be achieved with THIOPAQ systems than in neutralization processes which immobilize metals predominantly by hydrolytic precipitation. In recent years, PAQUES has made significant advances in the design and operation of aerobic and anaerobic bioreactors for metal-sulfur systems. Moreover, the company has increased its technology portfolio to allow the development of more process oriented applications of THIOPAQ technology. A new PAQUES designed plant at Budelco treating sulfatecontaining proceswaters will be started up in 1999. The sulfate reduction is accomplished in a 500 m3 reactor in which hydrogen is used as electron donor. The endproduct, ZnS, is used for Zn and H2S04 production.

Jan 1, 1999

By Daoxin Wu

In this paper, the rutile TiO2 were prepared under air, Ar and H2 calcination atmosphere by low temperature hydrolysis using Tetrabutyl titanate (C16H36O4Ti) as raw material. Powers were characterized by X-ray diffraction, UV-vis diffuse reflectance and X-ray photoelectron spectroscopy. The influence of the calcination atmosphere on the photocatalytic reactivity of rutile TiO2 for oxygen production was investigated. The photocatalytic reactivity of rutile TiO2 prepared under air, Ar and H2 atmosphere was compared under ultraviolet and visible light radiation with Fe3+ (c=8.0mmol.L-1) as electron acceptor. The results showed that rutile TiO2 prepared under Ar and H2 atmosphere had higher photocatalytic activity for oxygen production than that prepared under air atmosphere. The oxygen production rates under ultraviolet irradiation were 427.5, 378.2 and 357.0µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere. The oxygen production rates under visible light irradiation were 78.2, 52.2 and 13.5µmol.l-1h-1 respectively when rutile TiO2 was prepared under Ar, H2 and air atmosphere.

Jan 1, 2008

By R. Ghisleni, R. E. G. Bohrer, L. Radtke, R. M. C. Santana

"The major source of environmental pollution in urban areas is the transport sector and its impact on human health and the greenhouse is preoccupying. In many works of literature is monitored the pollutants in urban cities, however in specific areas such as universities, they are scarce. Therefore, the aim of this work is to monitorate the gaseous pollutans in a bus terminal at Santa Cruz do Sul University-UNISC and to develop a control framework of the air quality. Six points were selected for monitoring, being one of them inside a bus. The monitoring of CO, HC and CO2 were carried out on arrival and departure of the bus. Preliminary results conducted in a day of spring showed that the most critical condition was during the night shift, where the concentration of CO (200 ppm) was the highest, caused by the vehicles increase, due to the larger number of students.IntroductionThe first major global assessment of climate change science in six years has concluded that changes in the atmosphere, the oceans and glaciers and ice caps show unequivocally that the world is warming. The report released on February 2, 2007, the first of four volumes to be released this year by the IPCC, also confirms that the marked increase in atmospheric concentrations of greenhouse gases is the result of human activities.The transport sector has become by far major source of environmental pollution in urban areas. The continual traffic growth has raised concerns over the impact of traffic emissions on human health and urban environmental quality, and has fuelled the demand for a coherent regulatory framework for the management of traffic, air quality and emission at urban level, as well as at regional and national scales.In Greater Metropolitan São Paulo, Brazil, fossil fuel combustion in the transportation system is a major cause of outdoor air pollution (Miraglia&El Kouri, 2007). In China several studies on gaseous emissions are being conducted by F. Costabile&Alegrini, (2007), developed a study on the pollutants in the city of Beijing suggesting methods for the control of pollution.The results obtained from the estimation of the atmospheric pollutants emitted monthly in Campo Grande/MS, Brazil, by buses and minibuses, which employ diesel, biodiesel or natural gas as fuels showed that the substitution of diesel by biodiesel would diminish the emissions of pollutants (Kozerski&Hess, 2006)."

Jan 1, 2008

By Peijia Lin

Wheat straw was chemically modified by alkaline treatment followed by succinylation and sodium carbonate treatment for the use of cadmium and nickel adsorbent. The adsorption efficiency was calculated in different conditions. The experimental parameters were solution pH, adsorbent dosage, contact time and initial metal concentrations. The biosorbent was analysed by FTIR (Fourier- Transform Infrared Spectroscopy) to investigate the changes of surface functional group. The maximum adsorption percentages of cadmium (>99%) and nickel (>98%) were achieved using 5 g/L adsorbent with 50 mg/L initial metal concentrations. The adsorption kinetic study showed that the reaction was pseudo-second order kinetics and the adsorption isotherm was well fit by the Langmuir adsorption model. The dynamic column study indicates that modified adsorbent has a better adsorption capacity towards cadmium than nickel.

By G. Hanko, A. Lebleu, M. Sibony, J. Lecadet

The New Jersey distillation process is today the most important pyrometallurgical method for the production of zinc of very high purity. The flexibility of the pyrometallurgical zinc production process, especially its ability for recycling, makes it competitive, although it is energy intensive. A deeper knowledge of the New Jersey process is necessary to further increase its technical performance by ensuring its global safety. A project, integrated in the European research program EUREKA, has been started in order to define the process chemistry of distillation. Experimental measurements have been carried out with a column at the laboratory scale, and the results, linked with industrial measurements, support the development of a model based on material and thermal balances. The first conclusions indicate that the key parameters for process optimization are the column geometry and the distribution of the thermal losses.

Jan 1, 2000

By S. P. Jupp

A 2-D coupled thermo-mechanical model was developed to simulate hot tandem rolling of AA5056 aluminum alloy using the commercial finite element software package, ABAQUS The model was used to predict the temperature, strain rate and strain distribution in the strip at any position in the roll bite and was verified through comparisons with literature results in terms of both temperature and strain predictions at the roll bite exit. A sensitivity analysis indicated that model predictions of temperature and strain at the roll bite exit were sensitive to the friction coefficient and moderately sensitive to the heat transfer coefficient for the conditions studied. Microstructure equations taken from the literature were used to make predictions at various positions in the strip. The temperature, strain rate and strain vary dramatically through the thickness of the strip in the roll bite. The sensitivity of the microstructure predictions to these parameters was assessed and it was found that using average values of temperature and strain rate in the roll bite versus exit values significantly influenced the resulting microstructure predictions.

Jan 1, 2001

By M. O. Lai

"Metal matrix composite (MMC) with composition of Al-4.Swt.%Cu reinforced by IOwt.%TiB2 or ISwt.%SiC particulate has been successfully fabricated using powder metallurgy technique. Disk, compression and beam specimens were prepared with (a) layered structure containing ductile Al-4.Swt.%Cu with brittle Al-4.Swt.%Cu/TiB2 or Al-4.Swt.%Cu/SiC layers, and (b) homogenous constituent with composition of Al-4.Swt.%Cu/lOwt.%TiB2' The specimens for the fracture toughness measurement were built through three ductile-brittle-ductile alternating layers. For the beam specimens, the layers were built through brittle-ductile-brittle sequence. The brittle layer consisted of Al-4.S%Cu with fixed amount of reinforcement. Fracture toughness testing revealed an increase for layered composites although the total amount of the reinforcement was the same for all disk specimens. The increase in fracture toughness is due to the existence of ductile layers which manifests a strong influence on delaying the occurrence of fracture. It acts as a barrier to resist the propagation of crack and hence increases the fracture toughness of the layered MMC specimens, Delamination in the beam specimens was observed to be due to shear stresses. Fracture surfaces of both disk, compress and beam specimens were characterized using the SEM. IntroductionMechanical and thermal properties can be achieved by the incorporation of refractory secondary phases to constrain the plastic flow of the matrix in a metal matrix composite (MMC). The size of the reinforcement particulate incorporated must be in the range larger than the dislocation cell size and strongly bonded to the matrix (I). Particulate reinforced metal matrix composites hence provide high modulus, improved wear resistance and strength (2-4). Because of the incorporation of refractory phases which are generally brittle, the major limitation in the mechanical properties of MMCs is their limited ductility in comparison to their base metals. Cracks normally initiate from the reinforcement and voids (4, 5). Due to the lack of ductility, cracks propagate rapidly with increase in load. As a result, the interactions between reinforcement particles and propagating cracks have recently been of great research interest (6). In addition, volume fraction of reinforcement and aging condition of the matrix significantly affect the mechanical behaviour of MMCs. In the case of AI-3.5%Cu reinforced with varying volume fractions of SiC particulate, it has been found that the probability of particle fracture increased with increasing volume fraction of reinforcement (7)."

Jan 1, 1996

By Takamitsu Nakasuga, Haiping Sun, Kyushu University, Katsumi Mori

"The kinetic behavior of reduction of chromite ore by liquid iron containing carbon and silicon has been investigated under various experimental conditions to clarify the reduction mechanism. It was found that the reduction rate of chromium ore by liquid Fe-C alloy was very slow. In addition, when carbon and silicon coexisted in the iron melt, silicon was found to preferentially oxidized to form silica, which favored for the fonnation of liquid slag and the rate of reduction was considerably accelerated. The similar effect was obtained by the addition of some fluxes, such as SiO2, Na2B407, CaO-SiO2, which also promoted the formation of a liquid slag and thus the reduction rate in the early stage also increased.IntroductionThe reduction of Cr2O3 is a basic reaction for production of ferro-chromium from chromite ore and for chromium recovery from the slag fonned during the decarburization period of a stainless steel-making process. The reduction of chromite ore consumes much energy and its reaction rate is not so high. Thus, in order to increase the reduction efficiency, it is strongly desired to clarify its reduction mechanism from the practical and the theoretical points of view."

Jan 1, 2000

By S. Suda

Hydrogen storage materials have been investigated for more than 30 years, particularly on metal hydrides. These materials are, however, considered today impractical because of their poor hydrogen capacity measured by mass density and their poor surface properties and characteristics against impurities. Recent R&D activities have been located in new categories of materials such as complex hydrides and chemical hydrides. Among these materials, NaAlH4 (one of alanates), Li-based complex hydride, and NaBH4 (SBH: sodium borohydride) are 3 major candidates as hydrogen storage materials. In the presentation, SBH as a non-reversible on-site but recyclable off-site is described in view of its practical availability as the source of H- (protide) applied for a new type of fuel cell named Direct Borohydride Fuel Cell (DBFC) and H2 (hydrogen) for Proton Exchange Membrane Fuel Cell (PEMFC).

Jan 1, 2006

By W. B. Carter, A. T. Hunt, G. W. Book

"Combustion Chemical Vapor Deposition (CCVDSM ), an open air, flame assisted CVD process, is under development. The CCVD process produces non-line-of-sight, epitaxial deposition. Materials deposited include YBa2Cu3Ox' Y2BaCuOx, BaTiO3, Y2FesOI2, ZrO2, yttria stabilized ZrO2 (YSZ), partially (yttria) stabilized ZrO2 (PSZ), and amorphous silica. Two modifications of the CCVD process are being studied. Liquid fuel CCVD deposition, involves the combustion of an organic solvent that contains dissolved reagents carrying the desired coating cations. Gaseous fuel CCVD deposition uses a flammable gas as fuel. A non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol prior to its combustion. Substrates to be coated are held near the flames' ends.IntroductionThin films and coatings can be deposited using a wide variety of techniques including chemical vapor deposition (CVD). CVD is ""a materials synthesis process whereby constituents of the vapor phase react chemically near or on a substrate surface to form a solid product.""lIn conventional CVD processing, gases carrying coating constituents flow into a reaction vessel where deposition occurs onto a heated substrate. The deposition process is often conducted at reduced pressure. Both cold and hot wall reaction chambers are used. Heat can be provided by a resistance furnace, rf induction, or high-intensity radiation lamps. Plasma, microwave, photo, laser, RF, and electron-enhanced CVD processes have been developed. The necessity of using a reaction vessel limits the substrate size and affects coating economics. Although most CVD depositions are performed as batch processes, continuous deposition can be accomplished with the use of appropriate hardware.The chemical vapor deposition of thin, dense oxide films has been accomplished in the open atmosphere with a flame assisted process. The process is called combustion chemical vapor deposition (CCVDSM).2 Two modifications of the CCVD process have been developed. The liquid fuel CCVD process involves the combustion of an organic solvent in which reagents (containing the coating cations) are dissolved. The gaseous fuel CCVD process uses a flammable gas as fuel. In this modification, a non-flammable solution containing dissolved reagents is either aspirated into the flame or mixed with the fuel gas as an aerosol of small droplets prior to its combustion. Substrates to be coated are held near the flames' ends."

Jan 1, 1994

By Zhijing Zhang

Long-term thermal stability of ionic liquids is essential for reliable performance of ionic liquids in any engineering applications. TGA studies were carried out on a series of ionic liquids with different cations and anions such as 1-butyl-3-methylimidazolium chloride ([C4mim]Cl), 1-hexyl-3-methylimidazolium chloride ([C6mim]Cl), 1-hexyl-3¬methylimidazolium tetrafluoborate ([C6mim]BF4), 1-hexyl-3-methylimidazolium hexafluorophosphate ([C6mim]PF6), 1-octyl-3-methylimidazolium hexafluorophosphate ([Csmim]PF6), and 1-butyl-3-methylimidazolium bis(trifluromethanesulflonyl)imide ([C4mim][Tf2N]). The short-term thermal stability of ionic liquids was evaluated by measuring the onset temperature of decomposition of ionic liquids, and the long-term thermal stability of ionic liquids was also evaluated by weight loss of ionic liquids over a long period of time at various temperatures. The experimental results showed that the long-term thermal stability of ionic liquids decreased with increasing temperature and was significantly lower than the onset temperature of decomposition of ionic liquids.

Jan 1, 2002

By Cui Wang, Qian Li, Kexin Jiao, Haibin Zuo, Jianliang Zhang

Abstract：A rational cooling water system is the assurance for long campaign life of blast furnace．In the paper, the heat transfer of different furnace period and different furnace condition based on the water quality characteristics were analysed, and the reason of the heat flux over the normal from the hydrodynamics was analysed. The results showed that, the vapour-film and scale existence significantly influenced the hearth heat transfer, which accelerated the brick lining erosion. The water dynamic characteristics of the parallel inner pipe or among the pipes were the main reason for the abnormal heat flux and film boiling. As to the reasonable cooling water flow, the gas film and the scale should be controlled and the energy saving should be considered.

Jan 1, 2015