Search Documents

By Bo Yan, Jiaquan Zhang, Haibo Sun

"Based on the validation of steady-state isothermal mathematical model by a 0.4-scale water model for the single-strand slab casting tundish, the effect of varying pouring temperature on the flow, temperature field, and residence time distribution(RTD) of the liquid steel was studied by a transient hydrodynamic model. Due to the decreasing temperature of ladle stream over a casting period of 50 min, the direction of vortex flow at the downstream side of dam changes to clockwise from the anticlockwise at 4 min after the new teeming, and reverts to anticlockwise direction again at 43 min. Meanwhile, the melt flow state in the dam hole is also varying with time. For conventional isothermal water modeling, the RTD parameters obtained are much different as compared with the non-isothermal ones. For the flow control devices(FCD) design, however, the identical optimal scheme can be concluded from the point of view of isothermal modeling.IntroductionOriginally, tundish was adopted as a buffer and distributor to hold and allocate molten steel for sequence casting upon ladle exchange and to provide a desired steel flow rate to the mould below. With the increasing demand to strand quality, the tundish has become a critical metallurgical reactor to enhance inclusions removal, avoid reoxidation of molten steel, and prevent slag entrapment. The general trends to obtain these metallurgical effects are to optimize steel flow pattern and to extend the residence time of molten steel in the tundish through increasing the volume of tundish and/or using FCDs in the interior of the tundish."

Jan 1, 2012

By Robert Vidal

A model of the homogeneous chemistry and transport processes within the separator of a chrome-alum electrowinning cell is introduced, discussed, and compared to experiment. The influence of diffusion, electromigration, and convection are included; it is found that convection was the dominant mode of transport for the experimental conditions. Simulation results explain experimental observations concerning an apparent disappearance of dichromate ions produced at the cell anode. The relation between potential drop across the diaphragm and the current and fluid flow is also illustrated. The model is used to recommend future experimental and theoretical work.

Jan 1, 1994

By Tong Zhilin

The reasons why the pits were formed on the cathode in the process of Ni electrowinning and the methods how to prevent these pits from forming are described. Some examples are presented. It has 'been proven that P507 and P204 present in the electrolyte can effectively prevent pits from forming on the cathode.

Jan 1, 1993

By R. G. Hilton

This paper deals with application of Super Detox? stabilization technology to the treatment of electric arc furnace dust (US-EPA listed hazardous waste KO61 ). The process has been used on approximately 170,000 tons of electric arc furnace dust. In addition to the nearly four years of commercial experience at Sterling, Illinois, the process is now being permitted for application at two other locations. The process was originally developed by the Bethlehem Steel Corporation and then further improved by Conversion Systems, Inc. (Bethlehem Steel's Licensee). The treatment process offers many unique bases for its selection, including: A) Low cost compared to the treatment alternatives; B) Lowest available TCLP leachate levels for any process treating K061. Many other processes leave some residue that represents a disposal requirement, although often not addressed; C) Produces minimized final waste disposed, including the fact that the total volume of dust generated and less than the volume occupied by the residue slag from HTMR; and, D) Opportunities for the beneficial utilization of part or all of the waste stream through the development of chemical and physical characteristics. Each of these aspects will be specifically discussed in the paper, including that status of the operations now under permit.

Jan 1, 1994

By Patrick Clark

As part of the Mine Waste Technology Program (MWTP), a large-scale column test using bacteria and a sulfide ore was conducted at McClelland Laboratories, Inc., in Sparks, Nevada. Four technology providers participated in this demonstration. A mining company in Nevada provided the sulfide ore, process effluent and make-up water. A process effluent column, a chemical oxidation column, and the four biological treatment columns were set side by side on a test pad outside the laboratory building. The process effluent and chemical oxidation columns were used for experimental control. The goal of this project was to evaluate the viability and feasibility of using these biodegradation technologies to reduce the cyanide to the regulatory level of 0.2 parts per million (ppm) within an acceptable timeframe and with low operational costs. The column testing began on December 3, 1998 and operated until May 17, 1999. One technology provider reached the regulatory level within the 158 days. The remaining three biotechnology columns were approaching the regulatory limit at completion of the demonstration. The MWTP is funded by the U.S. Environmental Protection Agency (EPA) and is jointly administered through an interagency agreement with the U.S. Department of Energy (DOE).

Jan 1, 1998

By N. Kanari

The kinetics of oxychlorination of MgO by C12+02 was studied in the temperature range of 850 °C - 1025 °C, using thermogravimetric analysis. The effects of C12/02 ratio, gas velocity, temperature and partial pressure of reactive gases on the reaction rate were investigated. The oxychlorination process was characterized by an apparent activation energy of about 214 kJ/mol. The reaction orders with respect to C12+02, C12 and 02 at 950 °C were about 0.65, 0.98, and -0.37, respectively. Some data about oxychlorination kinetics of MgO, Cr2O3, and MgCr2O4 contained in chromite were compared. Efficiency of using oxychlorination for the removal of iron oxides contained in magnesia was demonstrated.

Jan 1, 1999

By Bo Zhou

During secondary aluminum recovery, complex aluminum scraps are melted and refined often in a rotary melting furnace and the aluminum metal has to pass through a molten salt layer and melt down in a bottom aluminum bath. Previous experimental study and industrial observations have indicated that salt shell formation and re-melting on the metal solids in the early stage plays a critical role in the overall melting process of the scrap. In the present paper, mathematical models are developed to simulate the process of salt shell formation and its re melting, as well as aluminum melting in the molten melt. Influence of the salt layer properties, the residence time of the metal particles in the salt layer, the particle size, the temperature of bulk melt were investigated. Reasonable agreement with the measurement data was reached. The developed melting model will be used to construct a population balance model of the scrap melting behavior for a rotary melting furnace, taking into account the distributed characteristics of the scrap. Finally, an overall process model based on Computational Fluid Dynamics (CFD) for the rotary furnace will be constructed, coupling with the population balance model for the scrap melting.

Jan 1, 2003

By Akira Nishikawa

During the twentieth century the copper smelting industry achieved dramatic expansion corresponding to the vast growth of global economy. This was largely due to innovations in pyro-metallurgical processes, such as autogenous smelting and continuous smelting and converting technologies. However, as copper production capacity increased, its impact on the environment also could not be ignored, and thus with increasing global environmental awareness, many smelting operations either had to renew or rebuild their facilities. In addition to these changes, in places like Japan and Europe, with scarce primary resources, the treatment and recovery of metals from a variety of items such as car shredder dust, used electrical appliances and electronic devices, on top of scraps traditionally treated, is having a profound effect on the reduction of waste and the preservation of primary resources. Thus compared to the days when copper smelting focused on the environmental control in order to break with "Smoke Stack Industry", copper smelting today is making an important contribution to the sustainable development of human society.

Jan 1, 2003

By Theo Lehner

The Rönnskär smelter has wide experience in the field of recycling of non-ferrous metals. Today, smelting and refining from primary and secondary raw materials are integrated in a complex flow sheet. Boliden operates a lead flash smelter, a lead refinery, a copper smelter and refinery, a sulphuric acid and sulphur dioxide plant, a slag fuming plant and precious metal plant at its Rönnskär smelter in the North of Sweden. The Business Area Smelter Operations also incorporates Boliden Bergsöe, Sweden's lead-acid battery recycler, and Norzink, Norway, where recycled zinc accounts for more than 20% of it's production. Raw materials for the Rönnskär smelter include concentrates, ashes, slags, metallic scrap, electronic scrap and electric arc furnace (EAF) steel-making dust. This paper briefly describes current operations and illustrates current measures to improve productivity. Limits to recycling as experienced by a non-ferrous smelter are, illustrated. The deportment of critical elements contained in raw materials is also discussed.

Jan 1, 1998

By Thomas Brynjulfsen, Merete Tangstad, Eli Ringdalen

Manganese ore fines cannot be added to the submerged arc furnace directly as they will prevent even gas flow through the burden. Low gas permeability in the burden will lower the degree of pre-reduction of ore subsequently increase the carbon and energy consumption of the process. In order to utilize manganese ore fines in the furnace, they are typically agglomerated into sinter. In this work, the melting and reduction properties of Gabonese sinter and Gabonese ore have been investigated in pilot scale experiments. Two experiments were conducted, one with 100% sinter as manganese source and one with 50/50 sinter and ore. Lime was used to achieve a charge basicity of 0.72 in both experiments. The composition of slag samples from the excavation of the furnace was established using EPMA(WDS), and the composition of the tapped slag and metal was found using XRF. It was found that while the coke-bed size would determine the tapped slag composition, the melting behavior of the Mn source would determine the mixing with lime.

Jan 1, 2014

By Kampe. S. L., Baker. Andrew H., Tony Zahrah

"Experimental heats of reaction for the formation of several Al3Ti + TiB2 intermetallic composite formulations have been determined utilizing bomb calorimetry. To overcome the kinetic constraints and achieve ignition in these formulations, a boron (B)/potassium nitrate (KNO3) initiation aid was incorporated within the blended reactant compact. The heat contribution from the initiation aid was regressed to provide estimates of the heat of reaction of the nominal formulations. Powder x-ray diffraction was utilized to identify the products of the reaction and discern any differences between the predicted equilibrium products of the formulation and the actual products.IntroductionReaction synthesis is a technique for the creation of ceramics, intermetallics, and in-situ composite materials [1]. Reaction synthesis is defined by its self, propagating mechanism, where the energy liberated from a localized reaction within a green powder compact is enough to carry the bulk reaction to completion. Achieving a self, propagating state can be achieved in variations of two primary methods of initiation: uniform volumetric heating and directional propagation [2].Uniform volumetric heating involves subjecting a green compact of the unreacted formulation to uniform heating in a furnace to encourage diffusion to initiate the reaction (Figure 1a) throughout the bulk material. Directional propagation utilizes a point heat source at one section of a green compact of unreacted formulation (Figure 1b). The localized exothermic reaction at one point in the compact then initiates the reaction in the section of the compact adjacent to it and fully propagates throughout the entire compact until completion. Initiation of the localized reaction is generally associated with the melting of the constituent with the lowest melting point, with instantaneous initiation of the reaction usually occurring close to that melting point [1]. This melting point can be high in some systems of interest, such as the titanium (Ti) and boron (B) system in equation 1:"

Jan 1, 2011

By R. A. Alock

The character, occurrence and genesis of the three types of nickel deposits, sulfide, laterite and deep-sea nodule are described, highlighting the differences in mineralogy and chemical composition that effect the extractive metallurgy of nickel and associated byproducts. World nickel production and current resources by deposit type and geographic location are also reviewed.

Jan 1, 1988

By A. Siegmund, Gerhard Martin

The recycling of metal containing scrap is a common practice in the industry and has a long tradition. . In rec~nt years, this philosophy has been transferred to organic materials, in particular to thermoplastic polymers. BSB . Recycling GmbH, a company with a long experience in the treatment and recovery of lead from battery scrap,· had recognized this exploitation at an early stage and challenged it by a consequent continuation of the idea to recycle materials other than metals without degradation and maintaining the quality. These efforts resulted in an economic and environmentally acceptable solution producing high quality polypropylene compounds at BSB beside lead and lead alloys from battery scrap. The raw material fair the production of polypropylene compounds is shredded plastics from the separated casings of spent lead-acid batteries. The production of polypropylene with specific physical and mechanical properties is carried out by the accurate dosing of organic as well as inorganic additives. The result of the procedure is a novel product group "Seculene PP", a registered trademark of BSB Recycling GrnbH.

Jan 1, 2000

By Min Chen, Nan Wang, Zhen Tian, Yingying Shen

"The enrichment behavior of phosphorus in CaO-SiO2-FeOx-P2O5 slag was studied by making an investigation on the distribution of phosphorous content in slag and 2CaO·SiO2 phase. The research results showed that the existing 2CaO·SiO2 solid particles in slag were the sites for the phosphorous enrichment. The enrichment process of phosphorus in CaO-SiO2-FeOx-P2O5 slag can be recognized as: mass transfer of phosphorus from bulk slag toward the surface of 2CaO·SiO2 particle, superficial dissolution reaction of phosphorus to 2CaO·SiO2 and diffusion of phosphorus through the product layer of 2CaO·SiO2-3CaO·P2O5 solid solution to the inner of 2CaO·SiO2 particle. Compared to the 2CaO·SiO2 particles with larger size (500µm to 1000µm), the completion time of enrichment was shorter for the particles with smaller size (less than 50µm).IntroductionDuring ironmaking and steelmaking, significant amounts of slag are produced. Contrast to the high utilization of ironmaking slag, the treatment of steelmaking slag is more difficult and challengeable, and therefore, an alternative approach is to recycle the steelmaking slag inside the ironmaking and steelmaking process itself. The main limitation to the reuse of steelmaking slag inside the process is that the refining process may be aggravated caused by the phosphorous accumulation if it is used in the blast furnace burden [1]. At the same time, the phosphorous content of steelmaking slag (approximately 1%~5% P2O5) is too low for it to be used as raw material for fertilizer [2, 3]. Moreover, owing to the diminishing supply of global iron ores with low phosphorous content, the control of phosphorus in iron and steelmaking processes has become an increasing problem, and as a result, more amounts of high phosphorus containing steelmaking slag are produced. Therefore, a valuable approach is quite appreciated in which the steelmaking slag is recycled within the ironmaking and steelmaking process and at the same time, the high phosphorus-containing phases in the steelmaking slag, suitable for use as fertilizer can be separated and recycled effectively [4]."

Jan 1, 2011

By Joo Hyun Park, Kyu Yeol Ko

The viscosity of the CaO-SiO2-xMnO-yCaF2 slags (C/S=1.0; x=10, 40%; y=0 to 15%) was measured to clarify the effect of CaF2 on the viscous flow of molten slags at high temperatures. Furthermore, the Raman spectra of the quenched glass samples were quantitatively analyzed to investigate the structural role of CaF2 in a depolymerization of silicate networks. The critical temperature of the slags abruptly increased at 15%CaF2, which was confirmed to originate from a crystallization of cuspidine using XRD analysis. The viscosity of the slags continuously decreased by CaF2 addition in the 10%MnO system, whereas the viscosity of the 40%MnO system was not significantly affected by CaF2 addition. The effect of CaF2 on the viscosity of the slags was quantitatively analyzed using micro-Raman spectra of quenched glass samples accompanying with a concept of silicate polymerization index, Q3/Q2 ratio. A polymerization index continuously decreased with increasing content of CaF2 in the 10%MnO system, whereas it was not affected by CaF2 in the 40%MnO system. Consequently, the bulk thermophysical property of the CaO-SiO2-MnO-CaF2 slags was quantitatively correlated to the structural information.

Jan 1, 2014

By T. Gunawansa, T. L. Alford, Zhao Zhao, A. R. Lanz, N. David Theodore

Many sustainability issues arise during the manufacturing processes that are currently used for solar cells. Solar energy is a renewable energy source that is independent of the earth’s resources, and it is therefore important for the development of more sustainable technologies. Microwave annealing (MW) has been proposed as a technically feasible fabrication scheme for large area silicon solar cells. Apart from that, microwave annealing has been demonstrated to be a promising alternative for repairing damage and electrically activating dopants in ion-implanted semiconductors for integrated circuit manufacturing. A microwave oven is cheaper than conventional furnace systems. In addition, microwave heating is much more efficient than conventional furnace heating, as heating is directly produced inside the material. This minimizes the loss of energy due to heating of the ambient. There is a need for more efficient processing techniques. In this study, microwave annealing is used as an alternative to the current postimplantation processing. Arsenic-doped silicon was microwave annealed (with an aluminacoated silicon carbide susceptor) to activate dopant atoms and to repair damage that was caused by ion implantation. Sheet resistance and Hall effect measurements were used to assess the extent of dopant activation. Rutherford backscattering spectrometry (RBS) with ion channeling was conducted to determine the extent of recrystallization. The dopant activation and recrystallization resulting from microwave annealing is compared with that resulting from conventional rapid thermal annealing (RTA) with the same heating profile. The results show that when compared to RTA, susceptor-assisted microwave annealing results in better dopant activation for shorter anneal times under the same heating conditions.

Jan 1, 2015

By Zhigang Liang

Effects of the configuration parameters of submerged entry nozzle on the flow field in slab mold were investigated through a water modeling. The experimental results showed, when the original submerged entry nozzle was applied, there was an appreciable level fluctuation in the mold with obviously naked surface and entrapment of mold flux at higher casting speed. By increasing the outlet area of submerged entry nozzle, without any change of other configuration parameters and submergence depth, a proper fluid field with active surface and good covering of mold flux can be obtained, which is proper to meet the requirement for increasing the casting speed and improving the slab quality simultaneously.

Jan 1, 2009

By D. W. Ashman

The zinc pressure leaching plant at Cominco's Trail Operations is now in its ninth year of production. The plant produces a zinc sulphate and jarosite slurry which is further processed in the calcine leaching circuit. Elemental sulphur, a by-product of the process, is sold in the North American market. During the past eight years, a number of changes have been made to the plant to remove known production bottlenecks and to improve leaching extraction. These changes have raised production rates above the initial design so that the plant currently accounts for approximately 20 percent of Trail s zinc production. These rates are expected to be increased further upon the completion of the alterations currently in progress. The knowledge gained over the operating life of this plant has allowed Cominco to plan for a possible future expansion of the zinc pressure leaching plant. If expanded, zinc pressure leaching would account for approximately 48 percent of cominco?s zinc production.

Jan 1, 1990

By Ronald L. Pariani

To date, significant advances have been made regarding the development and commercial implementation of full deposit stripping in the copper industry such as practiced at Copper Refineries, LTD in Townsville, Australia. The paper describes the history and current practice of Electrowinning (EW) plants which may be coupled with solvent extraction. The modular nature and degree of automation are described in relation to the various sizes of operations. Reference is made to the expansion capability of commercial equipment plus associated economics of the mechanical processes for producing full cathode deposits. It is recognized that the technology described may be adaptable to other nonferrous refining areas where feasible. The paper highlights the state of the art in mechanized stripping equipment as applied to current and planned SX-EW plants.

Jan 1, 1987

By James E. McNulty

Today's energy era is the beginning of a transition from the Petroleum Age to a future age of renewable fuel resources. Fuels for the transition era will come from unconventional sources and conversion technology. Affecting the practicability of transition technologies are attitudes of the public, capital requirements and availability, patterns of fuels utilization, producibility of fuels and the actions of governments. Primary energy sources to replace deficiencies of oil and gas and provide growth in the period of transition will be coal, oil shale, nuclear energy and peat.

Jan 1, 1981