Search Documents

By V. Gornitz

The Orphan mine uranium deposit, Grand Canyon, Arizona, is a cylindrical collapse-breccia pipe, 70 to 150 m in diameter and 500 m deep. Pipe fill was derived from the Supai Group, Hermit Shale, and the Coconino Sandstone. Uraninite, with Cu, Fe, Pb, Zn and Ni-Co sulfides is concentrated along the pipe boundary ring fracture (annular ring) and within the central porous sandstone matrix. There is some suggestion of vertical and lateral zonation of U with respect to Cu. Reduction of ferric oxide cement from red beds and recrystallization of carbonate, with formation of kaolinite preceded major ore deposition. Early Ni sulfides, arsenides and disseminated pyrite were followed by massive pyrite, and botryoidal uraninite, which in turn was suc-ceeded by Cu, Zn and Pb sulfides. A second, later generation of uraninite was closely intergrown with hematite and base metal sulfides. Oxidation of primary minerals may have been associated with Tertiary regional uplift. The paragenetic sequence closely resembles that of other Grand Canyon breccia pipes, except for the extensive development of the distinctive uraninite-hematite association. Mineral assemblages at the Orphan suggest possible mixing of the metal-bearing solution(s) with a more oxidized fluid, containing soluble uranyl complexes. Homogenization temperatures of fluid inclusions in calcite (GO-lIO?C) at the Orphan fall within the lower end of the range observed at other breccia pipes.

Jan 1, 1987

By Nils Lippmann, Ulrich Weber, Siegfried Schmauder, Jr. Mishnaevsky

"A computational approach to the optimization of fracture resistance of multiphase materials (here - high speed steels) by varying their microstructure is presented. The main points of the optimization of steels are as follows: (1) development and verification of the model: numerical simulation of crack initiation and growth in real microstructures of steels, (2) computational experiment: simulation of crack growth in different idealized quasi-real microstructures and (3) the comparison of fracture resistances of different microstructures and the development of recommendations to the improvement of the fracture toughness of steels. Numerical simulations of crack growth in real microstructures of steels and different idealized carbide distributions are carried out. On the basis of the simulations, recommendations for the improvement of high speed steel microstructures are given. It is shown that the fracture resistance of the steels is much higher for the fine than for the coarse version of the same type of microstructures.IntroductionThe purpose of this work is to develop an approach to the optimal design of multiphase materials on the basis of numerical simulation of their behaviour under mechanical loading. We suggest here the following strategy:1. Collecting input data for the simulations: taking a micrograph of a microstructure, and determining mechanical properties and failure conditions of the material constituents [1, 2],2. Simulation techniques and assumptions are tested for a real microstructure of the material: crack growth in a real microstructure is simulated and then compared with the experimental data,3. Computational experiments: different microstructures of materials are tested in the numerical model under the same loading conditions. The calculated service properties of the different microstructures are compared, and recommendations are developed. As differentiated from the ""real"" experimental techniques, the computational experiment is much cheaper and not labor- and time-consuming."

Jan 1, 2001

By J. M. Rapkoch

In late October 1996, an acid plant at a major U.S. copper smelter was faced with unexpected and rapidly increasing pressure drop across the gas cooling tower in the acid plant, indicating a build-up on the packing. This threatened to halt operations if not resolved. Earlier that month, a smaller vessel in the acid plant was found to be completely plugged with lead sulfate. It was feared that a similar fate awaited the gas cooling tower unless the scale build-up was stopped. Although lead sulfate is present in most copper smelter acid plants, this accumulation was unusually severe. An investigation was launched to find the source of the lead, determine how lead is transported to the gas cooling tower, recommend operating practices to prevent such severe scaling, and seek ways to recycle the lead value in the scale covered polypropylene packing. Late in the investigation it was learned that the lead originated from an improperly executed recycling program.

Jan 1, 2000

By Donald J. Hallbom

Limonitic nickel laterites slurries exhibit complex rheological properties including time dependency that varies from thixotropy to rheopexy. Chronic problems may occur if plant designers and operators fail to take time dependency into account. Stress decay tests indicate that laterite slurry takes roughly two minutes to approach steady state after a step change in the shear rate. As a result, most rheometer measurements are taken at a non-equilibrium state, making evaluation difficult. Two minutes is also long relative to the time that a unit of slurry in a processing plant is at any given shear state, so the slurry may never reach equilibrium. This paper presents a method to describe the rheology of laterite slurry using a Flow Array, which describes the rheology using an array of instantaneous flow curves crossed by an equilibrium flow curve. A rate equation for structural change in non-equilibrium conditions allows time dependence to be efficiently modeled. This flow array allows the flow behavior of time- dependent slurry to be predicted in non-equilibrium conditions using a simple time-step methodology. Keywords: Rheology. nickel laterite, hydraulic transport, pressure acid leach, flow array

Jan 1, 2004

By Robin D. Rogers

Room temperature ionic liquids (RTIL) can replace certain traditional organic solvents in liquid/liquid extraction of metal ions from aqueous systems. The very low vapor pressure and non-flammable nature of RTIL warrant consideration of these neoteric solvents for new processing technologies which will reduce pollution, Increase safety, and lower costs. Metal ion separations in RTIL, however, will typically require the use of an extractant and research is needed to identify suitable selective extractants which have appreciable solubility in the RTIL and low solubility In the aqueous phase. Choice of extractant should also take into account the toxicity, expense, and disposal of the ligand.

Jan 1, 1999

By Yasumasa Hattori

An extensive study including fluid dynamic calculations, cold model tests, pilot plant tests as well as measurements in a commercial flash furnace was carried out in order to develop a new Sumitomo flash smelting concentrate burner. The pressure measurements in the commercial burner indicated that the premixing of the concentrate and reaction air in a burner was insufficient. Pilot plant tests showed that enhancement of the premixing of the concentrate and reaction air is very effective for improving the burner performance. Using the additional pressure drop of the reaction air as an indicator of the premixing, a new type Sumitomo premixed concentrate burner was developed.

Jan 1, 2003

By M. Barkhudarov

The results are presented of research aimed at validation and development of a general purpose CFD code FLOW-3D. FLOW-3D is a commercial code developed by FLOW SCIENCE, INC. A number of physical modeling experiments involving the filling of cavities of different geometries with coloured water have been performed in order to compare the measurements with the results of computer simulations. Other numerical calculations were also done to be compared with the known analytical solutions.

Jan 1, 1992

By Norbert L. Piret

From the copper smelter operation a various outputs are to exert negative impacts on the environment. Particularly, emissions like SO2 and dusts, solid wastes like contaminated gypsum and arsenic sludge, effluents and heated cooling water are generated. Most countries have sitipulated an environmental legislation to provide the framework for an efficient environmental management. As part of the planning activities for x major greenfield copper smelter, the Following elaborations are required and were drawn up. -The Environmental Impact Assessment which is the first step of environmental management and mandatory for every new project. - The Environmental Monitoring Plan, which describes the monitoring procedures for the main impacts identified and assessed. -The Environmental Management Plan, which deals with the minimization of environmental impacts, and the methods of its implementation.

Jan 1, 1996

By Husamuddin Ahmadzai

A survey of regulations and state of the art control technologies is presented relating to the smelting of primary aluminium, copper and recycling of residues. Some costs associated with the alternatives and trends for the coming decade in this. sector are identified.

Jan 1, 1992

By M. C. Ruiz

The leaching behavior of chalcopyrite concentrate in acidic CuC12-NaCI-O2 solutions was investigated. Experiments were conducted under continuos flow of oxygen at atmospheric pressures. The results indicated that among the variables temperature has the largest influence on the dissolution of chalcopyrite in this medium, and high copper extraction can only be obtained at temperatures near the boiling point of the solution. It was also found that the stirring speed did not influence appreciably the dissolution of chalcopyrite. An increase in the oxygen flow rate up to 0.1 1/min increased the copper extraction. The total chloride concentration affects the dissolution of chalcopyrite up to about 4 M. Copper extraction of 93 % was obtained in leaching chalcopyrite of size fraction -400 # Tyler at 105 OC in 2 hours.

Jan 1, 1997

By Onwukamike, Onyedika G. O, Ogwuegbu M. O. C., K., Onyenehide C

A detailed mineralogical and elemental characterization of a lead (Pb) ore deposit from Ishiagu, Ebonyi State, Nigeria was carried out with XRD, SEM-EDX, and ICP-OES based mappingtechniques. The results show that the most dominant and valuable metal is lead (Pb = 95.02%, mass fraction). The main mineral is galena. Ilmenite and sphalerite occur as minors, which account for 2.71% and 0.80% respectively. Elements like Al, Ca, Mg, Ti, Na, Mn, Si and Sn occurred in trace amounts and are disseminated in the entire ore body.The surface and interrelations of the crystals were examined with x-ray mapping and the result shows the pattern of dissemination of the minerals within the ore body.

Jan 1, 2015

By S. P. Marsh, D. Banerjee

"Casting processes involve phenomena that occur on widely disparate length-scales. Simulation of macroscopic effects, such as heat transfer and convection, are generally addressed by solving the appropriate equations in discretized form on a finite-element mesh. Microscopic phenomena are described by micromodels that may be empirical or analytical in form. Coupling of phenomena in these two regimes is a critical issue in predicting microstructure and defect formation resulting from macroscopic process conditions. A formalism has been developed for expressing micromodels in a consistent manner using stereological parameters to quantify the geometric characteristics of the developing microstructure. This approach provides a robust and physically consistent method for coupling local micromodels with the macroscopic fields. The macroscopic state variables at each node serve as global constraints on the micromodels that are applied to a local unit volume. An outline of an equiaxed solidification model based on this approach is presented, along with preliminary simulation results. Coupling of convection and enthalpy effects between the micro and macro regimes is also discussed. IntroductionThe primary goal of casting simulations is to improve the reliability of cast parts while minimizing cost and development time. Effective simulations can speed up the mold design process and reduce the likelihood of defective parts by refining a particular casting process on a computer, reducing the dependence on cost- and time-intensive prototype castings. The challenge in developing effective simulations stems from the need to address physical processes that occur over a wide range of length-scales, from microscopic (atomic) and mesoscopic (microstructural) scales to macroscopic distances comparable to the size of the casting itself. Overviews of the various thermophysical phenomena and computational factors that are important in solidification modeling are provided in the literature by Rappaz [1] and Tseng et al. [2].Macroscopically, the solidification process is largely governed by the rate of heat flow from the alloy through the mold wall. Another important effect that occurs on the scale of the casting size is convective flow of the melt, which is driven by density-variations in the melt. Macroscopic calculations employ finite-element or finite-difference methods to solve the sets of equations that govern these effects, and the spatial resolution is determined by the grid spacings used for the calculations. Typical spatial resolutions are on the order of 10-2 to 10-3"" meters. This represents a compromise between the resolution required to simulate the continuum transport processes accurately, and the computational time required to model the entire solidification and cooling process."

Jan 1, 1994

By P. Felix

A discussion on the need of visualization and animation tools in modelling solidification processes is made. An outline of an approach for the production of a video computer animation is provided. A number of examples including, 2 and 3 dimensional melting, filling, and macrosegregation are presented.

Jan 1, 1993

By João M. S. Rodrigues

The use of sandblasting as a treatment method for conditioning anodes for zinc electro-winning was investigated and compared with conventional fluoride preconditioning. The anodes were made from two different lead-based alloys (Pb-Ag-Ca and Pb-Ag). Laboratory results showed that sandblasting and preconditioning both minimize lead contamination in the zinc and sludge generation. Sandblasting was found to have no aggravating effect on the anode corrosion. The sandblasting treatment was tested on Pb- Ag-Ca anodes on an industrial scale in the celJhouse of a local zinc producer. An unexpected finding of the large-scale tests was that the sandblasting appeared to strengthen the anodes, resulting in reduced warping during handling and operation.

Jan 1, 1996

By Aarne Kopanen

In recent years, various renovations have been carried out in the production chain of the Outokumpu copper refinirg process. The anode casting shop, which is the final integral production section at the Harjavalta copper smelter built in its original form in 1945, was fourxl unsuitable for technical and capacity demads during longer periods of operation, and a new casting shop was built in 1974. The electrolytic copper refinery of Outokumpu Oy at Pori was built in 1941, and subsequently expanded in two stages. Even with its present limited scale of production it has been fom important to mechanize the main operations. This work was started in 1967 with the design and construction of the starting sheet machine connected with the cathode washing and unloading machine as a combined unit. Mechanized treatment of anodes has gained advantage particularly from the new design of a highly automated anode casting shop. In the further development of the mechanization a stripping machine for, starting sheets was designed and installed, starting operation in 1974.

Jan 1, 1976

By Adele Garkida

Compacts of crushed waste window glass, fluorescent tubes, drinking glasses and laboratory glass wares were made at various proportions from 106 microns and minus 75 microns powders in combination with 5% bentonite as binder for each glass type, after several trials to determine compatibility of particle sizes. They were made using the uniaxial press at 10,000 psi and sintered at a temperature range of 700- 750oC. The results showed anisotropic shrinkage behavior for all the samples, exhibiting an axial shrinkage lower than the radial shrinkage. Sintered compact from waste drinking glass which comprised of 60% 106 microns and 40% minus 75 microns powders showed the least sintering shrinkage factor of 1.125, fused at 700oC and the highest shrinkage factor of 1.286 obtained at 750oC. This shrinkage behaviour connotes that sintering can be employed to utilize these waste glasses up to the maximum of 95% recycled glass content in ceramic tile production.

Jan 1, 2008

By Ho-Jung Shin

The influence of cooling rate from 1873 to 1473 K on the size and morphology of austenite grains was studied using a Fe-O.I5 % C-I.5 % Mn alloy. The experiments were carried out at three different cooling rates of O.33KJsec, O.67KJsec and air-cooling. The austenite grain showed an isotropy at 0.33KJsec but maximized anisotropy at O.67KJsec and become much less. anisotropic. In order to account for these phenomena, a model was developed for estimating the size and morphology of austenite grains as a function of cooling rate. The driving force for the )( phase formation from 0 phase is caused by undercooling degree due to cooling rate and energy barrier is restricted to the misfit strain energy which is caused by mismatch between )( phase and 0 phase. The )( phase from 0 phase could be formed on not random orientation index systems but specific orientation systems depending on cooling rate.

Jan 1, 2001

By Hye-Sung Kim, Dong-Wha Kum, Gyeungho Kim

"Mechanical alloying is an effective way to finely distribute inert dispersoids in AI-TM (TM is a transition metal element) systems. It is considered that high melting point aluminides are formed by precipitation from the supersaturated aluminum matrix. The analysis is based on the fact that much higher content of TM than the solubility limit can be dissolved in alpha aluminum during the high energy ball milling. Nonetheless, the role of undissolved TM particles affecting the formation of aluminides is not suitably considered. In this paper, authors present experimental observation on the formation of Ab3Ti particles from mechanically alloyed AI-Ti alloys in the hyper-peritectic region. This study showed that, in the mechanically alloyed AI-20wt%Ti specimen, intermediate phase of cubic Ab3Ti and tetragonal AIz4Tis formed at 300 - 400°C and 400 - 500°C, respectively, before the MA-state reaches to the global equilibrium at higher temperatures. The formation behavior of Lh- Ab3Ti is interpreted by interdiffusion of Al and Ti in solid state based on the fact that large amount of nano-sized Ti particles exist in the milled powder. Present analysis indicated undissolved Ti particles of nanosize should have played an important role initiating the formation of Ab3Ti phase during annealing.IntroductionInterest in the hyper-peritectic AI-Ti alloys is based on industrial demand for high-modulus and high-temperature aluminum alloys. Earlier works on hyper-peritectic AI-Ti alloys with 4 to 12wt%Ti show that these alloys are strong at ambient temperature and maintain high strength above 300°C when titanium-trialuminide (e.g., Ab3Ti) is finely distributed in the aluminum matrix [1,2]. High melting point and high stiffness with low density of AbTi make the AI-Ti alloys strong with greater thermal stability while keeping weight savings as much as possible. Titanium in aluminum shares other merits of transition metal additions because Ti solubility in Al is low (i.e., 1.l5wt%Ti at 665°C and virtually zero below 400°C), and fine dispersion of Ab3Ti particles is readily accomplished and resists grain coarsening effectively."

Jan 1, 1996

By Jerome P. Downey

Technologies developed within the field of extractive metallurgy to recover, concentrate, and purify metals and industrial minerals from ores, have served as the foundation for all of the subsequent environmental remediation, materials recycling, and waste management technologies. This paper discusses the application of classical extractive engineering principles to the development of a thermal process for the recovery of mercury from solid wastes. Process development is presented as a series of logical stages, which begin with a thorough characterization of the site-specific waste, move on to bench and pilot scale testing of the process options, and end with a functional process flowsheet. This paper also presents thermodynamic data on many mercury species of interest to the minerals, power, and chemical industries. These data can be used to model the speciation and recovery of the mercury as a function of various process parameters.

Jan 1, 2003

By Wei-feng Liu

On the basis of the brief introduction of the gold-antimony concentrate smelting process in China, some problems in the original process were analyzed and the corresponding improvements were introduced in this paper, such as the treatment of antimony matte, the refinement of gold-silver alloy, the concentrating gold from gold-antimony alloy, the treatment of soda slag. The roasting method that was used to treat the antimony matte was transferred to the ore dressing method. The solvent extraction was used to refine the gold-silver alloy instead of the electrolytic method. The technology of selective chlorination leaching under controlling potential was applied to concentrate gold from the gold-antimony alloy and gold-lead alloy instead of the electrolysis method. Soda slag was recovered by the second reducing smelting method substituting for the mixed-salt method of sodium arsenate. After those improvements, the process has been done smoothly; the direct recovery rate of metals has been greatly increased. Meanwhile the procedure

Jan 1, 2008