Search Documents

By Pinakin C. Chaubal

An industry ? university consortium was set up to develop advanced tools necessary to understanding of the various phenomena occurring in the hearth of the modern iron making blast furnace. The major driver for this work was to provide the technological support required to extend campaign life of blast furnaces, which, by current agreement is tied to the life of the furnace hearth. The hearth wear is significantly affected by the hot metal velocity, temperature distribution and refractory temperatures. Due to the difficulty in making measurements inside the hearth, novel approaches to gain a fundamental understanding of the detailed physical and chemical processes in the hearth must be developed. The approach used in this project was to develop a 3-D CFD (Computational Fluid Dynamics) model coupled with extensive validation efforts. The CFD model is being utilized (1) to understand the phenomena in the hearth, (2) to understand the impact of changes in the internal conditions of the hearth on wear patterns; and (3) to design a monitoring/controlling system for prolonging campaign. In this paper, the results will be reviewed.

Jan 1, 2006

By Ji-He Wei

Keywords: stainless steel, AOD refining, side and top combined blowing, mixing characteristics, water modeling The fluid mixing characteristics in the bath during the side and top combined blowing AOD (argon-oxygen decarburization) refining process of stainless steel have preliminarily been studied on a water model unit of a 120 t AOD converter. The geometric similarity ratio between the model and its prototype (including the side tuyeres and the top lances) was 1:4. On the basis of the theoretical calculations for the parameters of the gas streams in the side tuyeres and the top lances, the gas blowing rates used for the model have more reasonably been determined. The influence of the tuyere number and position arrangement, and the gas flow rates for side and top blowing on the characteristics has been examined. The results demonstrated that the liquid in the bath underwent vigorous circulatory motion during gas blowing, without obvious dead zone in the bath, resulting in a well mixing effectiveness. The gas flow rate of the main tuyere had a governing role on the characteristics, a suitable increase in the gas flow rate of the subtuyere could improve mixing efficiency, and the gas jet from top lance could make the mixing time prolong. Corresponding to the oxygen top blowing rate specified by the technology, a roughly equivalent and good mixing effectiveness could be reached by using six side tuyeres with an angle of 27° between each tuyere, and five side tuyeres with an angular separation of 22.5° or 27° between each tuyere. The relationships of the mixing time with the gas blowing rates of main-tuyeres and sub-tuyeres and top lance, the angle between each tuyere, and the tuyere number have been obtained.

Jan 1, 2005

By A. E. M. Warner

At the Copper Cliff Smelter, Inco Limited has extensive experience in converting primary smelting mattes over a broad range of nickel/copper ratios and compositions. In the past 35 years, technology developments at Inco have reduced the number of Peirce-Smith converters in Nickel/ Bulk (nickel-copper matte) service from 13 to the current 5. This paper will discuss: ? The performance and life of ?stretch? 13.7m shells versus conventional 10.7m converters. ? Process control and information system development from the early 1980?s to view converter aisle status on a continuous basis to the recent central control of the stretch shells. ? Nitrogen cooling of finishing matte from plant testing to implementation in the early 1990?s to replace the dedicated cooling converters. ? The impact on converting of changing the smelter flowsheet in the early 1990?s. ? A current program to develop a converting strategy for the future to address environmental issues and profitability.

Jan 1, 2005

By V. Kamavaram

Keywords: Recycling, Aluminum Metal Matrix Composite, Ionic Liquids, BMIC Recycling of aluminum metal matrix composites (MMC) via electrolysis in ionic liquids at near room temperature was investigated. The electrolytic melt comprised of 1-butyl-3-methylimidazolium chloride (BMIC) and anhydrous AlCl3. Impure aluminum composite (Duralcan MMC Al-380, 20 vol % SiC) was electrochemically dissolved at the anode and pure aluminum (>98%) was deposited on a copper cathode. The deposits were characterized by scanning electron microscope, X-ray diffractrometer, and mass spectrometer. The influence of various process parameters such as concentration of electrolyte, and applied cell voltage on the recycling process was studied. The recycling process yielded current densities in the range of 200-500 A/m2, and cathode current efficiency of about 85%. The results indicated that impurities such as Cu, Si, Ni, Fe, Mg, Mn, and SiC particles were removed as anode residue. Energy consumption of about 3.7-6.3 kWh/kg-Al was obtained at a cell voltage of 1.0-2.0 V and cell temperature of 100 ± 5°C. Low energy consumption and no emission of pollutants are the two main advantages of this process compared to present recycling processes.

Jan 1, 2005

By C. M. F. Vieira

In the county of Campos dos Goytacazes, north of the State of Rio de Janeiro, Brazil, there is a large production of red ceramic, mainly perforated bricks. A percentage of these bricks are damaged during the firing processing and become a red ceramic waste. This work investigates a possible solution to this environmental problem through the mixture of fired brick wastes, up to 20 wt.%, with clay bodies to produce red ceramics. Cylindrical pressed bodies were fired at temperatures varying from 500 to 1100ºC. After firing, samples were then tested for linear shrinkage, water absorption and mechanical strength. The results showed that brick waste addition did not changed the workability of the clay and that up to 5 wt.% of waste no detrimental effect occurred on the fired properties at all temperatures.

Jan 1, 2010

By Jilai Xue

Experiments with various industrial cathodes ranging from 35 wt.% to 100 wt.% graphitic and fully graphitized carbons were carried out in a laboratory aluminum electrolysis cell. Sodium and cryolite bath penetration into the cathode samples was measured by XRD and SEM-EDS analysis. For a higher cryolite ratio in the bath, the cathodes with lower graphitic carbons exhibited more sodium penetration than the fully graphitized. The increased graphitization in the cathode materials can reduce Na, NaF and Na3AlF6 penetration. SEM-EDS inspection reveals that the sodium and fluorides penetration within the cathode samples has different patterns for varying graphitization of the carbon materials. XRD quantitative analysis indicates that there is a large percentage of Na3AlF6 in the penetrated bath. The results can provide useful information for quality evaluation of the industrial cathode products.

Jan 1, 2010

By Juliana Gutiérrez-Paredes

Keywords: Slag, chromium oxide, recovery, stainless steel Experimental and theoretical work was performed to estimate the effect of slag basicity and amount of reducing agents on the reduction of chromium oxide from the slag which interacted with molten steel at 1600°C. The slag system contained CaO, MgO, SiO2, CaF2 and Cr2O3 together with Fe-alloys (Fe-Si and Fe-Si-Mg). The CaF2 and MgO contents in the slags were 10 mass % each; Cr2O3 was 25%. The amount of the ferroalloys ranged from 12.5 to 50 g per 100 g of slag. The (CaO+MgO)/SiO2 ratio was held at 1 and 2. The Cr yield was determined using both Fe-alloys as reducing agents. Some estimations were made to determine the theoretical effect of temperature, slag basicity, (CaO+MgO)/SiO2, and amount of reducing agents in the slag on the chromium recovery. The FACT (Facility for the Analysis of Chemical Thermodynamics) computational package is used to determine the equilibrium between the slag and molten steel.

Jan 1, 2005

By Shadia J. Ikhmayies

The SnO2/CdS/CdTe thin film solar cells were fabricated on glass substrates by using the spray pyrolysis (SP) technique for the deposition of the SnO2 and CdS layers and vacuum evaporation for the CdTe layer. The transmittance curves were used to investigate the interdiffusion in the two interfacial regions SnO2/CdS and CdS/CdTe by taking the first derivative of the absorbance as a function of wavelength. The appearance of new bandgaps around the bandgaps of SnO2:F, CdS:In and CdTe layers is a strong evidence on the interdiffusion in the two interfacial regions and/or the formation of quantum dots.

Jan 1, 2010

By Jeffrey D. Winterton

Keywords: Copper, ion exchange, sulfonic acid, bis-picolylamine, ion exchange modeling, ion exchange kinetics As part of an investigation into the feasibility of using ion exchange resins to recover copper from aqueous waste streams generated during the manufacturing of semiconductor devices, the uptake of copper onto two ion exchange resins was investigated. The resins studied were DOWEX G-26, a standard gel type sulfonic acid resin, and DOWEX M4195, a macroporous chelating resin with a bis-picolylamine functional group. The equilibrium and kinetic behavior of the uptake of copper were investigated over a range of copper concentrations with constant sulfate concentration and different levels of acidity. The homogeneous structure of the G-26 resin yields equilibrium relationships that fit the Langmuir equation, and equilibration times of less than 30 minutes. The uptake behavior of M4195 is complicated by the need to absorb co-ions to maintain electroneutrality, resulting in uptake profiles that change character with increasing copper concentrations, and extended equilibration times.

Jan 1, 2005

By Li Chen

A new process, i.e. Ball milling--Neural leaching--Oxidation calcinations--Chloridizing distillation--Hydrolysis, was designed to recover germanium from the vacuum furnace slag produced in Shaoguan smelter. The suitable process and operational parameters were determined for the practical production.

Jan 1, 2005

By J. C. Pandey

The paper highlights the experimental investigations to characterize texture and plastic strain ratio r-Bar in auto grade steel sheets by ultrasonic measurements, whereas attempts were made to characterize interlamellar spacings in pearlite, tensile stresses and torsional properties in prestressed concrete wires by eddy current measurements. Good correlations were obtained between the testing parameters (such as ultrasonic attenuation and velocity in case of steel sheets as well as eddy current out put voltage and phase angle in case of steel wires) and the materials properties (such as texture, plastic strain ratio r-Bar, interlamellar spacings in pearlite, tensile stresses and torsional properties). 15 MHz normal direct contact and 20 MHz delay line normal shear wave probes were used for ultrasonic measurements. Eddy current measurements were done using an absolute coil probe with variable frequency selection. The experimental results show the possibility of nondestructive on line measurement of the above microstructures and properties.

Jan 1, 2010

By Mark C. L. Patterson

Hydrothermal brines are extracted from significant depths below the surface of the earth and arrive at the surface at elevated pressure and temperature. The exact chemistry and conditions of these brines depends upon the rock formations through which the water travels, but many of the brines are rich in dissolved minerals especially silica which is often saturated in the brine. At pressure and temperature the minerals remain in solution but in order to extract heat from the brines, they need to be cooled and during which many of the minerals precipitate causing problems. Where precipitation is a problem in the downstream processing, the brines are maintained at a high enough temperature and pressure so as to avoid precipitation and injected back into the geothermal formation. This results in a significant loss in potential energy that could be recovered from the geothermal brines. If left to precipitate in an uncontrolled manner, many of the minerals will precipitate as gels, in a high surface area form which is difficult to extract from the liquor and which can causes problems. Precipitation in this manner often builds up on the inside of pipes, reducing the pipe cross-section available for fluid flow and reducing the overall efficiency of the plant. If the brines are seeded at the appropriate time or the precipitation conditions are changed, mineral particles can be grown and separated more easily from the brine. During this precipitation and growth phase the chemistry of the local environment can also be altered to grow more valuable particulates. Some of the specific chemistries will be discussed with reference to known geothermal brines and what needs to be done to precipitate value added products. A theoretical approach to the complete extraction of minerals from geothermal brines is also discussed with the goal of extracting more heat from the brine prior to reinjection into the well.

Jan 1, 2006

By Taufiq Hidayat

Accurate description of complex phase equilibria provide the foundations for the improvement of non-ferrous pyrometallurgical smelting and recycling processes. Recent advances in microanalysis and experimental techniques enable accurate phase equilibria characterisation. Quantitative microanalytical techniques including Electron Probe X-ray Microanalysis and Laser Ablation ICP-MS enable the concentrations of major and minor elements present in different phases in samples to be accurately measured providing data that cannot be obtained using bulk chemical analysis techniques. High-temperature equilibration experiments coupled with the subsequent analysis of elementary reactions at micro- and macro-scales ensure the attainment of equilibrium conditions, and therefore, ensure true phase equilibria information is obtained. Examples of the application of the improved methodology on the investigation of phase equilibria of low-order and complex, multi-component gas/slag/matte/metal/solids Cu2O–PbO–ZnO–Al2O3–CaO–MgO– FeO–Fe2O3–SiO2–S systems and the distribution of minor element are provided. The experimental study is closely integrated with thermodynamic database development for the above system. Example of implementation of the research outcomes into industrial operations is demonstrated.

By M. Hochenhofer

Keywords: desulfurization, mathematical model, slag reaction To produce ferroalloys like ferro-nickel for alloying purposes in a quality that meets the requirements of today?s steel industry, refining processes like desulfurization and dephosphorization are indispensable. The performance of desulfurization-treatment by slag reaction depends on various parameters, such as: sulfide capacity and viscosity of the slag, sulfur distribution between metal and slag, activity of sulfur in melt and movement of melt. Within this work, the combined influences of these parameters on the desulfurization of a ferro-nickel alloy were examined. As a basis for this examination, a mathematical model, based on data from plant trials, was created. This model demonstrates the relationship between desulfurization rate and initial values of the above mentioned parameters. With this model the relevant parameters were evaluated and assessed concerning their influence on desulfurization.

Jan 1, 2005

Sm-Co alloy is a kind of magnetic material with high power and has been applied in modern industry widely. In this study, the wet chemical co-precipitation was developed for synthesis of the Sm-Co alloy oxide precursor. The thermodynamic analysis of the studied system was done to clarify the solution behavior theoretically based on the thermodynamic equilibrium and simultaneous equilibrium. Then, the experiments were done to address the various effects on the wet chemical process, including solution pH, reactant concentration, dispersant, reaction temperature and time, etc. It is found that by precise control of the process, the Sm-Co alloy oxide precursor was synthesized with fine crystallization and special size & size distribution.

Jan 1, 2005

By A. J. Rigby

Refractory linings in converters or anode furnaces used to over-oxidize the blister copper will suffer rapid deterioration, due to prolonged contact with copper oxide-rich slag. Nitrogen stirring with COP KIN porous plugs and use of SEMTECH OPC in converters and anode refining vessels can considerably reduce both refractory wear and processing times. In addition, careful control of the vessel atmosphere and the use of real-time optical process control minimize both slag volume and contact time with the vessel refractory.

Jan 1, 2005

By Won C. Park

Experiments showed changes in the mineral content of dolomitic oil shale at temperatures and exposure times which bracket conditions encountered during in situ retorting. Laboratory results correlate with cores from a spent in situ retort at Occidental's Logan Wash test site at Garfield County, Colorado. Dolomite, CaMg(CO3)2, decomposes rapidly to form periclase, MgO, calcite, CaCO3, and CO . Both calcite and periclase are intermediate products that can be stabilized by CO atmosphere at lower temperatures, while steam accelerates the formation 2 of silicates. The decarbonation of calcite appears to involve a direct reaction with both quartz and periclase in forming these silicates. Decarbonation preceeds the formation of akermanite, Ca2 MgSi 207, and diopside, CaMgSi 206, within several hours of heating and is followed by the nucleation of forsterite Mg2SiO4, and monticellite, CaMgSiO4. Under in situ retorting conditions, akermanite and diposide are the major minerals above 800°C. Equilibrium is not attained within 200-300 hours. In situ retorting temperatures above 800°C for extended periods of time should reduce potential ground water leaching by the formation of silicate minerals. These silicates are less soluble than free lime, magnesium or alkali oxides. There is a corresponding decrease in the natural pH of these silicates from approximately 12 down to 7.5 to 9:

Jan 1, 1981

By Purushottam Kumar

Keywords: Magnetostriction, magnetic properties, Pd(Fe,Co,Ni) single crystals Fe-Pd, Co-Pd and Ni-Pd alloy systems show appreciable magnetostrictive strains that are of interest for sensor applications. These systems exhibit congruent melting minima. In this work the magnetic and magnetostrictive behavior of congruent melting Fe-Pd, Co-Pd, and Ni-Pd compositions have been examined. The alloys examined include Fe-54.9 at.-% Pd, Ni-45.4 at.-% Pd, and Co-45 at.-% Pd. The paper describes the growth of bulk single crystals of these alloys using Czochralski technique. X-ray diffractometer was used to obtain rocking curves that were used to determine the [001] crystal direction. Magnetostriction in [001] direction was measured using strain gages. Magnetic properties were measured using a vibrating sample magnetometer. Ni-Pd showed the highest magnetostriction values among the congruent melting compositions. Magnetic and magnetostrictive behaviors of these alloy single crystals are presented.

Jan 1, 2005

By Hong Yong Sohn

Keywords: Barium sulfate, Barium sulfide, Environment, Kinetics, Pollutants, Sulfur dioxide conversion, Thermodynamics Nonferrous smelters and coal gasification processes generate sulfur dioxide streams, most of which are treated to produce sulfuric acid with the accompanying problems of market shortage and transportation difficulties. While the conversion of sulfur dioxide to elemental sulfur has many environmental advantages, no processes exist that are environmentally acceptable and economically viable. A method for converting sulfur dioxide to elemental sulfur by a cyclic process involving calcium or barium sulfide and calcium or barium sulfate without generating solid wastes has been developed. In this process, the sulfate, as the starting raw material, is reduced by a suitable reducing agent such as hydrogen to produce the sulfide, which is used to reduce sulfur dioxide producing elemental sulfur vapor and regenerating the sulfate. The latter is then reduced to reproduce the sulfide. This paper describes work on the BaS/BaSO4 system. Thermodynamic analysis and experimental results indicated that the BaS-SO2 reaction produces mainly sulfur vapor and solid barium sulfate and that the gaseous product from the BaSO4-H2 reaction is mainly water vapor. The rates of the two reactions are reasonably rapid in the temperature range 700-1050°C.

Jan 1, 2005

By S. Tanaka

The Tamano Smelter of Hibi Kyodo Smelting Co. Ltd. was commissioned in 1972. Since start up, the anode production capacity has increased from 101,000 tpy to 290,000 tpy, as a result of the application of continuous improvements at each phase of the expansion projects. The Tamano Smelter had developed several innovations, including the original coke combustion technology for Flash Smelting Furnace operations (T-FSF), and has also been able to extend the operating life of the Peirce-Smith converters. This paper will present several improvements implemented at the Tamano Smelter, and will discuss relevant P-S converter operation.

Jan 1, 2005