Search Documents

By M. A. Cocquerel

External process energy requirements and air pollution control regulations formulated to limit particulate and SO2 emissions are impacting on smelting and converting technologies and the corresponding process and secondary gas handling systems. This paper presents an overview of the different technical solutions used for cooling and dedusting the process gases in the different pyrometallurgical copper concentrate stages, including: drying, smelting, converting, slag cleaning and fire refining. The main principles of the process gas handling systems are presented &d a qualitative technical and economical comparison is discussed in relation to process changes, energy recovery and marketing or disposing of the various sulfur fixation by-products. Finally, a brief review of the methods for fixing sulfur contained in the process and secondary gases is presented.

Jan 1, 1999

By Liyuan Chai

The corrosion mechanism of A3 steel induced by chloride ions in the purified water had been investigated with the A C Impedance technique. The results showed that there were another two factors which determined its electrochemical corrosive rate: the electrode potential and coverage ratio of chloride ions on the surface of A3 Steel. The corrosion mechanism of A3 steel in the solution with chloride ions emendation was two steps of electrode process with the rate-determining step of 0,32kFeClFeCle+--¾¾®++.

Jan 1, 2009

By G. A. Brooks

The problem of treating concentrates with increasingly higher levels of arsenic and antimony is compounded by the trend to stricter environmental guidelines regarding the disposal of smelter wastes. Much of the arsenic and antimony from non-ferrous processes is recovered as oxide fume. The options for handling these fumes include recycling them to the smelter, stabilising and disposing of them, and recovering values from them. Whilst arsenic oxide has little value, there is a market for antimony oxide and this provides an incentive for devising techniques for separating antimony oxide from arsenic oxide before disposal of the arsenic oxide. Arsenic can be separated from antimony oxide by selectively volatilising the more volatile arsenic trioxide from a mixed oxide sample or by selectively condensing the less volatile antimony tetroxide at high temperatures, leaving arsenic trioxide to condense out at lower temperatures. The results of selective volatilisation experiments at 379 to 587 °C indicate that it is difficult to achieve an arsenic content below 5.0 wt.% using air or nitrogen as carrier gas due to the formation of solid solutions between the two oxides. Injection of oxygen into a mixed vapor stream improved separation by selective condensation and antimony tetroxide containing as low as 0.23 wt.% was obtained in laboratory experiments.

Jan 1, 1994

By C. Mattich, A. L. Beyzavi

The Waelz Plant at Taiwan Steel Union Co. Ltd. (TSU) was erected within nine months from September 1, 1998 to May 15, 1999. The nominal capacity of the plant is 50,000 tonnes per year of electric are furnace dust (EAFD). The plant, consisting of material handling, a waelz kiln, a waste gas cleaning system, waelz oxide leaching and waste water treatment, was commissioned within three months from July 1, 1999 until October 12, 1999. The specific problem of the plant is the high chlorine content in the EAFD pellets which is up to 6 %. Lurgi Metallurgie GmbH, Frankfurt, Germany was responsible for the engineering erection and commissioning of the plant.

Jan 1, 2000

By ZhiLong ZHAO, Lin Lin, Zhancheng Guo, Jingtao GAO, Huiqing Tang

Grain sticking often occurs in the fluidized bed reduction of f ine iron ore, which is closely related to the precipitation morphology of metallic iron on the surface of ore particles. In this work, simulating the gas-solid reduction process of iron ore, in situ observations were carried out to investigate effects of doping mineral oxides on the precipitation morphology evolution of metallic iron during reduction of iron oxides with CO. Results indicate that the precipitation morphology of metallic iron is related to the quantity of doped mineral oxides. The minimum mole fraction of doped oxide ( xyOA N ) that can inhibit the growth of iron whiskers is related to its cation radius ( Ax r ), extranuclear electronic layers ( Ax n ) and valence electrons ( Ax q ). Their relation can be expressed as:

Jan 1, 2016

By E. Kozeschnik

A new model is presented for the simulation of the evolution of precipitates in a multi-component multi-particle multi-phase environment The mathematical formulation as well as the physical background of the model are briefly introduced and its capabilities are discussed on the example of a precipitation sequence in a complex steel. Keywords: Modeling, precipitation kinetics, nucleation, growth, coarsening

Jan 1, 2003

By Lin Yang, Minjun Tang, Shuishi Liu, Jianfeng Zhou, Linjiang Qing, Xiaolei Song, Yufeng Guo, Tao Jiang

"The dynamics of oolitic hematite magnetic roasting was studied. The results show that oolitic hematite magnetic roasting was controlled by the internal diffusion, and the diffusion coefficient was 9.018x10-7 m2·s-1when the oolitic hematite was roasted at 650°C. Magnetic susceptibility improves when temperature increases and roasted time prolonges under the condition of roasting at 650°Cfor 50min, with the magnetic susceptibility is 39.88%. CaF2 and Na2C03 can significantly improve the magnetic susceptibility at the same roasting condition, and the magnetic susceptibility was 63.35% and 57.99% respectively, thus the reduction of oolimic hematite was promoted.IntroductionWith the continual depletion of free-milling iron ores and its rising price, developing the abundant resources of oolitic hematite has become one of the main research areas. The oolitic hematite accounts for 10% of China's iron ore reserve, and it also accounts for 30% of red ore reserve in China [1]. In order to exploit the oolitic hematite, there are many beneficiation research methods, including fine grinding/selective flocculation/high intensity magnetic separation or flotation, high-gradient magnetic separation, low intensity magnetic separation/high intensity magnetic separation/reverse flotation, chloridizing roasting/acid pickling, magnetic roasting/leaching process etc [2]. However, the oolitic hematite is easy to slim and the valuable mineral is covered by the slim, because of the tiny granule of value mineral, then the ooides are formed due to the state of layer morphology formed by iron ore and ganaue minerals [3, 4]. Fairly good separation indexes were hard to be obtained by traditional separation due to its structural features, so the magnetic property of the iron minerals will be changed with the use of the magnetic roasting [5, 6], which result in hematite variably altered to magnetite and simplified technological process so that a good separation indexes will be obtained by using the low intensity magnetic separation. Therefore, in order to provide theoretical direction of how to use the oolitic hematite effectively through the magnetic roasting, the oolitic hematite of GuiZhou province was studied, which emphasized on researching the dynamics of oolitic hematite magnetic roasting."

Jan 1, 2013

By Zhong g. Shui-ping

A new type Pb-Ag (0.8wt%)-Bi (0~5.0wt %) alloy used as anode in electrowinning of zinc from sulphuric acid electrolytes was prepared. The electrochemical properties of this ternary lead alloys have been tested and compared with those of Pb-Ag (0.8wt %) anodes used in industry. Results show the anodic overpotential decreases with the increasing of Bi content in the alloys. When the content of Bi was 1.0 wt% and 5.0 wt%, the anodic overpotential is about 40?50 mV and 60?80 mV lower than that of Pb-Ag (0.8wt %) alloy, respectively. The formation of oxide layers on the surface of these alloys was traced by LSV methods and the composition of the anodic oxide layers was characterized by XRD and SEM analysis. The surface layer on the two type anodes examined is mainly composed of a?PbO2 and ß?PbO2. But different structure of the surface layer was observed, Pb-Ag (0.8wt%)-Bi (1.0wt %) has a more fine-grained structure as compared to Pb-Ag (0.8wt %). But the film on Pb-Ag (0.8wt%)-Bi (3.0wt %) alloy is rather friable, cracked and not tightly attached to the anode.

Jan 1, 2008

By Sergio N. Monteiro

Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.

Jan 1, 2009

By Alexander V. Suvorin, Vladyslav M. Sokolov

"The traditional technologies for production of the coprecipitated and deposited catalysts are analyzed from the standpoint of diversion of application of the feedstock and increase of efficiency for its usage. The options for return of the metals of spent catalysts to the catalysts production are described. The novel environmentally friendly and cost efficient approach for reutilization of the spent catalysts is realized in practice. It anticipates application along with spent catalysts of the waste generated in the catalytic productions. Reutilization of the Ni-containing catalysts is referred as an illustration. Introduction The recent development of large catalytic manufacturing for organic and inorganic synthesis, and petroleum refinery as well as for applied environmental catalysis has brought about increase and diversification of catalysts production. The generation of spent catalysts has been increased correspondently. The feedstock for production of catalysts is mostly metals in a form of nitrates, carbonates, hydroxides, hydroxydcarbonates. Sometimes salts of organic acids, of ammoniates, of chlorides and of sulphates occur. All these materials are scarce and expensive. So their repeated use by reutilization of spent catalysts is very actual issue. The traditional recycling the Fe-, Cr-, Ni-, Cu- or Zn-containing spent catalysts are carried out by pyrometallurgical reclamation of pure metals or alloys. They can not be used directly in production of catalysts [1, 2]. The hydrometallurgical approach is used for recycling spent catalysts with PGM, W, Mo, Co, Ni or Cu. It provides production of salts of these metals in a form of sulphates, chlorides, carbonates, hydroxydcarbonates and sometimes nitrates or ammoniates. Only a limited number of these salts can be used directly in production of catalysts. Material losses during catalysts production The basic feedstock for manufacturing coprecipitated and deposited catalysts that may be produced from the spent catalysts is aqueous solutions of metals nitrates. Their production is based on application of nitric acid as a dissolvent. About half of it is lost with the flue gases in a form of nitrates vapor and nitrogen oxides (II, IV). The last compound is generated by reaction:"

Jan 1, 2008

By D. P. Cook, M. I. Bloch, J. A. Dantzig

"In this article, we describe a combined experimental and computational program to study the filling of automotive wheels during low pressure die casting. Experiments are performed by placing thermocouples into the mold walls of a production caster for the Ford F 113 wheel to measure the temperature profiles in the die during processing, and to infer the filling pattern. Computational models are also developed using a 36° section of the wheel pattern, taken directly from CAD data files. We use these models to simulate the filling and heat transfer processes. Comparison between experimental and computational results are presented, demonstrating the viability of this procedure.IntroductionAutomotive companies are using increasing amounts of aluminum in production vehicles: While the main driving force is improved fuel economy through weight reduction, replacing steel wheels by aluminum also offers the potential for improved vehicle performance by reducing unsprung mass. For these reasons, many new vehicles are now supplied with cast aluminum alloy wheels, and the aftermarket for these wheels continues to grow.The most common production process for these wheels is low pressure die casting. The process is subject to numerous defects, including microporosity, cold shuts, cold folds, misruns and inclusions. Scrap rates at the caster of the order of 10% are not uncommon. Many wheels also have large production runs, into the hundreds of thousands of wheels per year. Thus, the cost savings from even small reductions in scrap rate have the potential to be quite significant.Most of the defects are associated with the filling and solidification processes in the mold. The molds are air cooled, and the placement and sizing of cooling passages is currently as much art as science. The ultimate goal of this project is to improve that situation, by implementing simulation procedures that enable engineering design methods to be used in die and process specification."

Jan 1, 2000

By Yang Xianwan, Zhu Xiaoyun, Guo Zhongcheng, Zheng Yanping, Zhai Dacheng

"Corrosion resistance of RE-Ni-W-P-SiC composite coating and 3 l6L stainless steel in corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations by means of immersion methods and anodic polarization curves obtained by DHZ-1 electrochemical synthetic tester and HDV-7 transistor constant potentiometer. Immersion experiment results show that corrosion rate of RE-Ni-W-P-SiC composite coating as-deposited in HCl solutions increases with the rise of HCl concentrations, on the contrary, the corrosion rate of the composite coating after heat treatment decreases with increasing the HCl concentrations the corrosion rates of the coatings as-deposited and after heat treatment in H2SO4 and H3PO4 solutions respectively decrease with the rise.of H2SO4 and H3PO4 concentrations the corrosion rate of the deposit as-deposited in FeC13 solutions decreases with increasing FeC13 concentrations, while the rate of the composite coating after heat treatment increases .with the rise of FeC13 concentrations.In addition, the corrosion rate of 3 l 6L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions at different concentrations increases with rising of concentrations. Furthermore, the corrosion rate of 316L stainless steel in the corrosion media of H2SO4, HCl, H3PO4 and FeC13 solutions respectively is much greater than that of the RE-Ni-W-P-SiC composite coating as-deposited and after heat treatment in the same corrosion media.1. IntroductionAll the materials and their products, when processed, stored and used, it is inevitable that the corrosion, wear, fatigue and crack occur owing to the actions of surroundings. Those early failure and abrasion, through all kinds of departments and profession that corrosion consumes one percent of tens of the steel products of the whole world; and two or four percent of the GDP is lost because of the corrosion."

Jan 1, 2000

By B. R. Adams

This paper discusses the use of a reacting CFD model to determine chalcopyrite kinetics in a drop tube furnace and to predict the reaction of a chalcopyrite concentrate in the reaction shaft of an industrial smelter. Reacting CFD codes can be applied to determine the consequences of the interaction of gas with particles and therefore improve the ability to derive kinetic parameters that take into account the temperature and oxidation histories that different particles will see. This paper describes the application of such a model to derive improved kinetic parameters for the pyrolysis and oxidation of chalcopyrite. The reaction shaft model includes the effects of turbulent fluid mechanics, entrained flow mixing, turbulent particle dispersion, heterogeneous particle reactions, radiative and convective heat transfer, and' surface and bath deposition rates. Particle reaction and composition characteristics are predicted as a function of particle trajectory and deposition and are used to aid in evaluating shaft performance.

Jan 1, 1999

By Guillermo J. Román

The precipitation of copper and zinc as cements from a copper alloys' spent pickling solution has been studied at laboratory and pilot scale, with the objective of designing an economic process to recover both metals and render a solution to be either recycled to the pickling process or treated in a standard fashion and produce a non-hazardous sludge. The sulfuric acid spent pickling solution already containing copper and zinc was used first to dissolve another solid residue originated in the copper alloys foundry to neutralize part of the acidity. The resulting enriched solution was treated separately with two reductants,; sodium borohydride and iron powder varying pH and excess of reductant under constant agitation. Under the best conditions, precipitation of over 95 percent of zinc and copper was achieved together with the reduction of lead and cadmium contents respectively. A process for the combined residues treatment is proposed.

Jan 1, 1995

By R. C. Hubli

Copper (II) chloride has proven to be an efficient lixiviant for copper sulphide ores and secondary sources of copper such as scrap. Nickel sulphides are generally associated with copper ores and copper-nickel matte is an intermediate product of processing mixed sulphides. While the copper species in aqueous chloride media are present as chlorocomplexes, the presence of nickel as Ni++ offers effective separation between the two by solvent extraction techniques. Oxidation of millerite by cupric chloride in sodium chloride solutions has been studied as a function of rate of agitation, leaching time, temperature, acid concentration and total initial cupric concentration. The reaction has a 1/2 order of dependence on initial cupric concentration in the range of 0.0 to 0.5M. The activation energy for the temperature range 333 -363 K has been found to be 59.2 kJ/mol with chemical reaction at the unreacted mineral surface as the rate controlling step. The rate expression, according to the shrinking-core model, for initial cupric concentrations between 0.0 to O.5M, is evaluated as

Jan 1, 1996

By David Ellis

The next generation of Reusable Launch Vehicle (RLV) will utilize regeneratively cooled combustion chamber liners in the engines. The current design calls for using a new Cu-8 at. % Cr-4 at. % Nb (Cu-8 Cr-4 Nb) alloy for the liners. Work is ongoing to characterize the thermophysical and mechanical properties of the alloy from - 253 to 800°C, the temperature range to which the alloy will be subjected during service. The alloy has been commercially produced in quantity for NASA. The powder size has been characterized and the microstructure examined. The powder was extruded into bar using a commercial extrusion press. In addition, samples have been hot isostatically pressed (HIPed) at NASA Glenn Research Center. Both processing methods produced fully consolidated material. Transmission electron microscopy (TEM) revealed highly faulted Cr2Nb and some elemental precipitates. Cryogenic tensile testing showed the extruded specimens had significantly higher strengths than NARloy-Z (Cu-3 wt % Ag-0.5 wt % Zr) even after being subjected to a simulated braze cycle. The Young's moduli (Cu-8 Cr-4 Nb) were lower than NARloy-Z. The lower moduli is highly beneficial for reducing thermally induced stresses in rocket engine combustion chamber liners and similar applications.

Jan 1, 1999

By Sh. Najisi, O. Lashkari, M. R. Ghomashchi, A. Charette

"One of-the important parameters in casting and foundry technology is the fluidity of molten metal. This parameter becomes particularly important when casting thin wall parts. Therefore, understanding and controlling fluidity plays a major role in fabricating sound and defect-free cast components.Semi-Solid Metai SSM, slurry is a mixture of solid and liquid, mushy zone, with solid volume fractions of 0.1-0.5 and apparent viscosity close to oil viscosity at room temperature. It flows easily under pressure and capable of making complicated shapes with high degree of die filling and integrity.In this study, the ability of the semi-solid slurry to continue to flow is investigated through the effect of different fraction solids and holding temperatures. The results show that in mechanically stirred, MS, semi-solid 356 Al-Si alloy, increasing fraction solid reduces fluidity. Furthermore, the results of MS-alloy are compared with a newly patented Rheocasting route, i.e. SEED, Swirl Enthalpy Equilibrium Device to highlight the differences of the two processes. In addition, the interrelationships between microstructural evolution and fluidity are discussed."

Jan 1, 2004

By Debbie Marshall

Process water is an important consideration in the development of a nickel laterite project. Depending on the location of the ore body, sufficient fresh water may not be available and it may be necessary to use seawater (or saline groundwater) for ore preparation. This introduces various species, which have major effects on materials of construction and leaching chemistry. This paper summarizes batch testwork completed at the Falconbridge Technology Center. The leaching behaviour of eleven different laterite ore samples were compared using seawater and fresh water. For brevity, six of the eleven samples are reported here-the other five samples showed similar results. Each ore type was leached under identical conditions in both freshwater and seawater and the leaching chemistry compared. The batch test results were confirmed in a continuous pilot plant, and leach kinetics for the two systems were compared. Keywords: high pressure acid leaching, laterites

Jan 1, 2004

By Chonghe Li, Xionggang Lu, Wei Xiao, Xingli Zou, Weizhong Ding

The reduction degree and rate of the initial ilmenite concentrate and pre-oxidation samples by hydrogen were investigated by using thermogravimetric analysis system. H2-TPR was used to detected reduction properties of the pre-oxidation products which were oxidized at different temperatures. The phase transformations and micromorphology changes during pre-oxidation and hydrogen reduction were identified by XRD and SEM. The FeTiO3 was decomposed into TiO2 and Fe2O3 at the temperature below 900 oC. With the temperature rising, Fe2TiO5 was the only stable phase in high temperatures. The reduction of pre-oxidation ilmenite concentrate was faster than the natural sample, which was attributed to the micropores generated on the surface of ilmenite concentrate during oxidation. The main phases of the reduction product were metallic iron, ferrous pseuodbrookite.

Jan 1, 2014

By Roger N. Kust

Removal of heavy metals from industrial process streams is becoming increasingly important for _the recovery and reuse of values in process tails. Technology has been available for several years which removes heavy metals, from dilute (0.1-3.0 g/L) streams, as hydroxide or hydrated oxide sludges, allowing discharge of washed cakes with up to 60% solids. This paper reports on improvements to this technology which now allows treatment of streams with metal concentrations in excess of 60 g/L while eliminating the need for thickeners. Streams containing copper, iron, aluminum, chromium, nickel, zinc, cobalt and lead have been successfully treated.

Jan 1, 1992