Search Documents

By G. T. Newell, J. G. Stone, V. M. Mejia

Introduction Advances in drilling have reached a point where large diameter cores can be recovered from "tight," or weakly indurated placer gravels. In such ground, core drilling can provide more reliable data regarding tenor than can be obtained using churn drilling or similar classical techniques. It can also provide metallurgical and geological information that is not available from samples obtained through alternate methods. In 1985, Coastal Mining Co, a subsidiary of M. A. Hanna, and Western Gold Reserves began to review a Tertiary placer deposit owned by San Juan Gold at North Columbia, CA, about 14 km (9 miles) northeast of Grass Valley. The deposit is one of the largest remaining unmined portions of the formerly extensive early Tertiary ancestral Yuba river system. It has been known since the 1850s, has been the subject of much technical literature, and has been the object of at least four previous drilling programs. The eastern one-third of the 6 km (3.7 mile) stretch of the channel between North Columbia and Badger Hill was partially stripped by large scale hydraulic mining in the late 1870s and early 1880s. Mining ceased in 1884 when the Sawyer Decision prohibited further discharge of hydraulic tailings into the Sacramento and San Joaquin Rivers. By that time, about 30 to 45 m (100 to 150 ft) of relatively low grade upper gravels had been removed over some 81 hm2 (200 acres). About 90 to 105 m (300 to 350 ft) of higher grade middle and lower gravels were left at least partially stripped. In 1914, a few churn holes were drilled along a widely-spaced line. In 1938-1939, Selection Trust conducted an extensive drilling campaign to evaluate the deposit. Particular attention was directed toward the partially stripped eastern portion. In 1968, the US Geological Survey drilled three churn holes in the eastern part of the deposit. The US Bureau of Mines conducted experimental mining and drilling in the Badger Hill area. In the late 1970s, Placer Service Corp. acquired a lease on the deposit. Between 1979 and 1984, Placer Service drilled 28 large diameter BADE (a German-manufactured machine) drill holes on the eastern portion of the deposit. The surviving records from the widely-spaced 1914 drilling program are fragmentary and the reported grade not well substantiated. The 1968 holes were drilled for scientific purposes. Again, drilling details are not available. However, detailed records for both the churn drilling program and the BADE program were available and formed the basis for the initial evaluation of the property. Geology The geology of the auriferous Tertiary gravels of California have been described by Whitney (1880), Lingren (1911), and, more recently, Yeend (1974). In general, the Tertiary gravels in the North Columbia area occupy a broad channel cut into pre-Tertiary igneous and metamorphic rocks. The upper, or white gravel is overlain conformably by volcanic tuffs and volcaniclastic rocks. A middle gravel is characterized by the presence of silicified and carbonized wood. A lower blue gravel unit has relatively coarser cobbles and contains a higher proportion of igneous and metamorphic cobbles than the other units. The upper gravel consists of interbedded pebbly sand and silty, or clayey sands with prominent cross bedding. Most of the pebbles are well rounded and consist mostly of white vein quartz and quartzite. The upper unit is moderately well compacted. Exposures in the walls of the old hydraulic mine pits stand at 45° and 50° angles. The gold content of the unit is well below an economic cutoff. The middle gravel - included with the upper unit by Yeend (1974) - is coarser grained, with carbonized wood, and 75 to 100 mm (3 to 4 in.) cobbles of metased-imentary and metavolcanic rocks in a sandy matrix containing abundant lithic fragments. The upper contact appears to be conformable, but the lower portion of the unit appears in places to consist of reworked lower gravels. The unit contains less clay than the upper unit and is somewhat more friable than the underlying lower gravels. The gold content, while somewhat higher than the upper level, is too low to be of ore grade. The lower gravel averages between 30 to 45 m (100 to 150 ft)

Jan 9, 1988

By A. Johnson

When are SMART transmitters the smartest choice? To answer this question requires a closer look at SMART transmitter technology. It is necessary to understand this technology in order to recognize how it can best be utilized to give the greatest value for the application. And, once the decision to buy transmitters has been made, it becomes a question of whose SMART transmitter to buy. For, although the under-lying technology is similar, the differences that exist in how the technology has been implemented can make a dramatic difference in the end result. What prudent users of SMART technology do is to analyze their needs by application before making their buying decision.

Jan 1, 1988

By S. Hicks

This technical note describes an alternative procedure that can be used in linear programming calculations where the compliance limit of lbs SO2/million Btu for the blending coal is subject to change. Dr. Mateer in his technical note titled "Coal blending for sulfur compliance" (ME, September 1994, p. 1103) defined an "excess sulfur" parameter that provides a valid constraint equation for a linear program optimization. The coals used by Dr. Mateer in his examples are shown in Table 1. To create the parameters for the constraint equations to blend to an SO2 content of 1.2 lbs SO2/million Btu, the excess sulfur for Coal A was defined as Sulfur excess% = 0.5 - 0.6*13,000/10,000 = -0.28 This equation was used to create the constraint equation -0.28A + 0.44B + 1.36C[<] 0.0 Another way to create the parameters for the constraint equation is given below. In these equations: •W is the total weight; •A, B and C are the fractional proportions of each potential blend stocks; •Sa, Sb and Sc represent the percent sulfur content of the blend stocks; •Ha, Hb and Hc represent the calorific content of the blend stocks in Btu/lb; and •H and S represent calorific and sulfur contents of the composite blend. The weight of blend to produce one million Btu is [ ]

Jan 1, 1998

By T. O. Price

In 1969 Holosonics designed and developed a portable system for conducting acoustical surveys in metal mines, with lead-silver veins as the principal targets. Recently this system has been proven useful in describing rock structures for advance geologic information in civil engineering application and underground construction applications. This paper discusses a case history of acoustical surveying from a series of pilot drill holes in an advancing tunnel. In acoustical surveying a pulsed acoustic signal is used to generate reflected signals from the rock formation. Arrival time, amplitude and phase of the returned signals can be determined. These data became the basis for a signal correlation program designed to relate the signals to their respected pseudo-planar reflecting interfaces. An application of acoustical surveying has recently been conducted in a portion of the excavation for the Washington Metro Area Transit Subway. The data results and conclusions of the program are discussed in the paper. Acoustical surveying was successful in predicting the occurrence of major jointing and foliation plane shearing ahead of the tunnel advancement.

Jan 1, 1974

The development of a successful restoration strategy for any drastically disturbed site is dependent upon a thorough understanding of the chemical properties of the spoils or mining wastes that need to be stabilized. The majority of revegetation research in the USA has been conducted on coal mining spoils and coal preparation wastes, and this paper will focus on these two materials and their modification for plant growth and water quality protection. Potential acidity derived from the oxidation of pyritic (FeS2) materials is the most important chemical factor that must be estimated and managed, but physical properties such as severe compaction or excessively low water holding capacity are also very limiting. Conventional soil fertility tests are very difficult to interpret for mine soils because of their tendency to extract elements from fresh, unweathered surfaces that are soluble in the extract, but not plant-available. A wide array of waste products such as sewage sludge biosolids and coal fly ash are readily available for use as mine soil amendments, but their utilization must be carefully matched against the needs of the post-mining plant community and their potential water quality impacts.

Jan 1, 2002

By Walter E. McCulloch

Installation of flash flotation in the copper concentrator of Freeport Indonesia in late 1986 and 1987 increased gold recovery by about 13%, while also increasing concentrator throughput. Copper recovery remained essentially the same. Flash flotation has since been included in a recently completed mill throughput expansion to 32,000 t/d (35,300 stpd) as well as in a current expansion to 52,000 t/d (57,300 stpd).

Jan 1, 1991

By Graham E. Rawlings

Geotechnical investigations for underground projects are subject to a variety of constraints, including factors such as accessibility, geological complexity, thickness of oberburden and finance. As a result, the extent of geological data available for route selection and assessment of underground design and construction problems may vary between wide limits. It is essential that the data collected, the degree to which it is representative, and the confidence with which the problems can be anticipated, should be reflected in the type of contract set up and the way in which the contract documents are written. The paper addresses the methods by which investigations can be focussed to make suitable overall ground assessments for feasibility level studies. Subsequent investigations can then be objectively directed toward obtaining data on specific geotechnlcal problems or aspects which impact tunnel, cavern and shaft design and construction. The extent of investigations at the preliminary and design engineering stages must be closely related to the geotechnlcal surveillance and control during excavation. Fixed-price contracts necessitate a secure geotechnical data base prior to bidding, and the provision of that to the tenderers. By contrast, &apos;design-as-you-go&apos; contracts minimize the geotechnical information needed before construction, yet require immediate assessment of the excavated ground for determination of support requirements and payment category.

Jan 1, 1983

Research has determined that ground control interaction problems in mining over a previously mined seam occur primarily in the tension zone created at the edge of the subsidence trough, and in areas above lower seam remnant pillars. Based on empirical and analytical studies, planning options for improving conditions on the upper seam have been developed to optimize extraction while minimizing the negative effects of seam interactions. These options include prediction of potential upper seam damage, guidelines for minimizing inevitable negative interaction effects, and recommended opening and pillar sizes, shape, and orientations, as well as design and planning procedures.

Jan 1, 1988

By A. Goulsbra, S. McAllister, R. Dunne

Since 1992, a tailings gravity re-treatment plant has been in operation at the New Celebration Gold Mine to recover aurifer­ous pyrite (Martins, Dunne and Gelfi 1991; Martins, Dunne and Delahey 1993). The gravity pyrite concentrate is ground in a Tower mill to liberate gold (average particle size around 25µm) prior to cyanide leaching. Although the re-treatment plant has met the predicted gold recovery, based on original laborat01y testwork, there is still room for improved gold recovery. This requires enhanced pyrite recovery, especially in the finer size ranges. The application of centrifugal gravity separators would seem to be an ideal means to achieve this criterion. In particular, the Falcon continuous centrifugal separator (Series C machines) would appear to be ideal for this particular duty. A testwork program to evaluate the application of the contin­uous Falcon to recover pyrite from New Celebration ores was unde1iaken over a six month period during the later part of 1997. The work involved laboratory batch testwork, followed by con­tinuous testing of the Falcon Cl0 (2tph to 3tph) and Falcon C40 (l00tph) units. A summary of the results from this evaluation program are provided in this paper.

Jan 1, 1998

By Werner Stahl, Karsten Keller

Vibration screens are commonly used not only in classifying bulk material but also in dewatering it. The lack of a comprehensive physical theory of dewatering often leads to difficulties in the design and operation of the vibration screens. Firstly, the dewatering of bulk material will be shown, based on a physical model. Because of the oscillatory motion of the liquid in the bulk, the inertial force of the accelerated liquid and the dripping of water out of the bulk or screen must be taken into special consideration. The physical model put forward shows the effect of the various operations parameters of dewatering screens. The comparison between dewatering theory and practice will be shown by measurements using coal, limestone, etc. Dewatering measurements, which have been conducted on a vibration screen, demonstrate that different vibration frequencies and rates of acceleration lead to different residual moistures. Finally, the possibilities of improving vibration dewatering will be described.

Jan 1, 1995

By P. E. Sperry, J. M. Duncan

INTRODUCTION The purpose of the report on which this paper is based is (1) to evaluate the potential for cost reduction of urban mass transit tunnels by use of alternative materials transport systems during the tunneling process, and (2) to identify research and development program elements to assure that the materials transport system will not become the limiting factor for the rate of excavation. The approach taken was: Review the state of the art of urban tunneling by extensive interviews with representatives of tunnel contractors, equipment manufacturers, government agencies and consultants, and by review of recent literature.

Jan 1, 1979

By H. E. Goetzman

A cooperative research project supported by the taconite industry and the Minnesota DNR was undertaken to establish quality standards for carboxymethyl cellulose (CMC) based organic binders. The objective of this study was to identify the effect of CMC quality parameters such as degree of substitution, molecular weight, and purity as well as the effect of inorganic extenders such as sodium carbonate on performance. These factors have been evaluated by green-ball testing with two taconite concentrates followed by pot-grate tests. Balling tests with bentonite and Peridur were conducted to provide baseline data. At a constant DS the molecular weight as measured by viscosity had the greatest effect on green-ball drop strength. Dry-ball compression strength was most dependent on CMC addition rate and sodium carbonate content. DS was not found to have a major effect on green-ball quality for medium molecular weight CMC.

Jan 1, 1988

By Alan P. Cook

Methane levels have been measured around continuous miners and compared with computer simulations of methane flow. A multi-channel data logger, reading continuously from six methanometers, has shown methane levels to vary at different positions around a continuous miner, with the cutting drum and the immediate face area not necessarily recording the highest concentrations. Methane levels in the driver&apos;s cabin are generally low compared with the return side. Computer simulations, using computational fluid dynamics, have been supported by the measured data, and have shown that methane behaviour within the first few metres of the face varies considerably for different bord and pillar development stages. Methane is diluted rapidly to acceptable levels, but the distance required for this is extended when ventilation flow to the face is restricted.

Jan 1, 1995

By Stefan Norgaard

In today's modern gold mining industry in Australia, and the world, more and more companies are recognising the competi­tive advantages gained by implementing an effective training program for operations (processing plant) personnel. Plant operators, or process technicians, are unique amongst all other gold mine employees. They are at work in shifts cov­ering 24 hours a day and their actions can have a profound effect on the operation's economic performance. To a large degree, the minute to minute decisions and actions of an operator can deter­mine whether gold is extracted to bullion in the goldroom or is discharged into the tailings dam. Experience has suggested that most small to medium sized gold operations in Australia, and even some large ones, have not implemented an effective training program. This is not attrib­uted to deliberate negligence or "anti" attitudes against training, moreover mill superintendents and metallurgy managers are technical people not oriented to human resource techniques. Usually the demands of designing, constructing and commis­sioning a gold plant overshadow the need for training in the first instance, In fact some well designed plants treating friendly oxide friable ore have little need for a dynamic well trained oper­ating staff. However, many plants do require a thinking team to optimise production and changing ore conditions towards the end of a mine's life can expose poor competence levels at large expense. Few managers will argue that training is a necessity and results in a win-win situation. The operators win by increased job skills, job satisfaction, clear career development and possibly better pay conditions. Trained personnel usually reciprocate with increased effmt and work ethic. The company wins also by having a thinking team which will maximise gold production and reduce operating costs.

Jan 1, 1998

In west-central England, 183 m (600 ft) below the Cheshire Plain, lie the evaporate remains of an ancient sea. Stratified into nine beds of salt separated by marl bands, the deposit stretches roughly 21 x 12 km (13 x 7.5 miles) and contains reserves of rock salt estimated as high as 400 Gt (440 billion st). The Winsford Salt Works, one of England&apos;s largest underground mines, extracts the Cheshire salt and sells it for use as animal feed, for application in de-icing programs, and as a key ingredient in sodium fertilizer production and a variety of other industrial processes. Because road de-icing is an important market, demand for Winsford&apos;s salt varies with the severity of British winters. Design capacity is 2.25 Mt/a (2.5 million/year). However, production peaked at 2 Mt (2.2 million st) in 1987. Over the past five years, annual production has averaged 1.6 Mt (1.7 million st). Run-of-mine salt averages 92.5% NaCl, mixed with about 5% marl. The marl was formed by deposition of a reddish dust blown into the Cheshire basin from deserts in what is now central Europe. Association with the marl adds color to the salt, producing tea-colored crystals that resemble unrefined sugar. Adaptation of coal mining systems Rock salt mining in the Winsford district began at least as early as 1682. Mining at the current site dates from 1844 but was shut down from 1892 to 1928. In the early 1900s, a series of catastrophic collapses and floods plagued and ultimately shut down then-active Cheshire brine-salt producers. Subsequently, Winsford reopened and began adapting mechanized underground coal mining systems to rock salt extraction.

Jan 1, 1992

By D. A. Lee

The selection of control system equipment for a mineral plant is based on several criteria, including opera tor interface, supervisory capabilities, ease of maintenance, ease of programming and configuration, compatibility with auxiliary control equipment, and total cost. The paper discusses the technical evaluation procedure with respect to control system equipment available today.

Jan 1, 1988

By Zvonimir Jam?ek

In Rudarski Institut Ljubljana (RIL), i.e. Ljubljana Mining Institute, we have developed CADRIL, a smaller CAD package which purpose is to overcome the difficulties by introducing Computer Aided Design in our mines. Program CADRIL is a graphics shell for several computer applications in mining. With the basic version of CADRIL all 2D working maps for daily use can be produced. Inserting different program blocks into CADRIL we get versions MAPRIL, TAHRIL, SECRIL and so on. The main purpose of all versions is graphics design. The main and most innovative feature of CADRIL is the screen four-word command menu. Not having pull-down or tablet menus is the speciality of this program. CADRIL contains 500 achievable commands. Each of them can be composed by choosing two to four expressions stored and shown in a specific four- column menu, sorted as objects functions, parameters and modes. Thus all commands are immediately accessible. As a result of its plainness and adaptability to the present working methods of mining engineers, CADRIL quickly attained a good reputation in our mines.

Jan 1, 1992

By Charles E. Melbye

INTRODUCTION In a discussion of South American exploration, it is difficult to know how much area to cover, as there has been such intense exploration for many years in all of the South American countries. Therefore, I have decided to discuss only Argentina, Bolivia and Peru in this paper, since I am most familiar with these three countries. This familiarity has been gained during my last 12 years of nearly continual exploration and mine development. Furthermore, these three countries form a contiguous block straddling the Andes Mountain chain for 2,200 miles in length N-S. Although Chile is part of this block, I excluded that country because it has had the longest recent history in South American exploration, and it is now in a mature stage where new important mines are being placed in production every year. Exploration must progress a lot for the other three countries to attain the stature of Chile. However, major exploration successes such as Yavacocha and Pieriva in Peru, Kori Khollu in Bolivia and Bajo Alumbrera, Agua Rica and Cerro Vanguardia in Argentina certainly indicates that these countries are rapidly accelerating in exploration successes and the resulting new mine developments. Also, by concentrating on three countries, I have avoided making this paper too lengthy. This paper will cover activities of both junior and senior mining companies, both of whom are making significant contributions to exploration. The junior companies often make the initial discovery, develop it further and then bring in a major company when large capital is required. Since most exploration is for gold and copper or combinations of these, most descriptions will cover these types. However, there are significant new exploration successes for zinc and for silver-lead-zinc, and they will be covered, as well. After descriptions of the various properties, there is included a discussion of the governmental policies of Argentina, Bolivia and Peru, as to how they are affecting exploration activities and budgets. Some of these problems could have a major negative affect on the future exploration plans of many companies. I have intended to cover what I think are significant exploration developments in each country, and if a company project is omitted, there was no intention to slight anyone. Since exploration results change monthly, there could be

Jan 1, 1998

Maximising margins in competitive markets demands superior productivity. Unfortunately, management systems developed early this century for other industries often drive counterproductive behaviours choking mining productivity. Many executives and managers waste valuable time and effort relying on simply training and communicating to improve managerial practices and attitudes. In covering practical human behaviour, the paper explains why this fails - and explains how to use systems to successfully drive improved managerial practices and attitudes. It highlights use of modern performance Measurement, Analysis and Reporting systems to drive behaviours and improve margins - without capital investment - and make executive and managerial work easier and more effective.

Jan 1, 1999

By D. L. Slyter

Coeur d'Alene Mines Corporation's Thunder Mountain project in Valley County, Idaho, is one of the most remote active mining operations in the US. High altitude, heavy snows, and proximity to wilderness complicate operations in this environmentally sensitive area. Mining is conducted by conventional open pit techniques while processing utilizes on-off heap leaching and Merrill-Crowe zinc precipitation. The project is one of a few similar operations which detoxify the leached ore prior to its removal from the leach pads. Both leaching and neutralizing ( detoxifying) circuits are closed and independent loops. After leaching, alkaline chlorine solutions destroy residual cyanide in the heaps. Calcium hypochlorite solution for the cyanide destruction is prepared by injecting chlorine gas into milk of lime solution.

Jan 1, 1998