Search Documents

By David M. Sullivan

Jim Walter Resources, Inc., (JWR) a division of Jim Walter Corporation, has 5 underground coal mines in Central Alabama varying in depths from 400-2500 feet. Gas Chromatography plays a vital role in safety and production at each mine. Chromatographic data is used to monitor working areas for safety and proper ventilation and to control the quality of extracted methane for sales purposes. Instruments have a1 so been employed during mine rescue operations. JWR's first Gas Chromatograph (GC) was installed in April 1984 to monitor gob gas taken from longwall gob areas and sold based upon BTU value. The GC allows maximum extraction rate of the gas within the quality guidelines. By late 1985, another system was purchased and both units were upgraded to perform an analysis of indicator gases which may appear during mine emergencies. Each unit has the ability to detect and measure the following gases at almost any level ; Oxygen (021, Nitrogen (N2), Methane (CH4), Carbon Dioxide (C02), Hydrogen (HZ), Carbon Monoxide (CO) , Ethylene (C2H4), Ethane (C2H61, Acetylene (C2H2) and a composite of hydrocarbon threes and above (C3+). The analytical run is accomplished in less than ten minutes and is completely automated. This report will introduce Gas Chromatography as applied by Jim Walter Resources for the analysis of underground mine air.

Jan 1, 1987

By Charles A. Weinstein

INTRODUCTION As a set of management practices, "Knowledge Management" (KM) has disappointed many of its early advocates. The core notion behind KM can be summed up in the oft- quoted adage, "If we only knew what we know." KM describes a set of tools, practices, and approaches for using data, information, and expertise-knowledge-resident in an organization to improve the performance of that organization. The idea was incubated, hatched, and grew among some the largest and most successful companies in the world. Some of these companies created "Chief Knowledge Officers." Many more collectively invested billions in a huge range of KM efforts, all designed to use their organizations' information and expertise to innovate, improve margins, sell, or accomplish any of a myriad of sound business goals. Some KM efforts were successful, and many were not.* Today, it is indisputably the case that KM as a named set of practices has fallen out of favor. Why, then, should KM be discussed at a conference on "Things that Actually Work" for plant operators? Because, in many instances, KM has actually worked. The practices that represent KM done right offer significant opportunities for plant operators to achieve real gains, especially in times of resource constraints and in the face of ever-increasing technical and commercial goals. The KM fad is all but over. The KM benefits continue to accrue to those who have applied the lessons learned from that fad, and implemented sound * Fair disclosure: I am not unbiased with respect to the potential impact of KM. Teltech has been a pioneer and leader in KM, both as a practitioner and as a leading consultant to other organizations.

Jan 1, 2004

By P. Mousset-Jones, F. Calizaya

This paper explains and discusses a computer program that has been developed to determine the ventilation design parameters for complex auxiliary ventilation systems such as those found in the construction of long excavations with multiple headings. The program is based on the principle of partitioning the system into segments of finite length, and formulating and solving the resulting networks recursively. The resulting network problems are solved analytically. With this program, the size of fans can be determined in order to reduce the total leakage and minimize the flow recirculation. The application of the program is illustrated by the detailed solution of an auxiliary ventilation system proposed for the Exploratory Studies Facility (ESF) at the Yucca Mountain Project, Nevada.

Jan 1, 1995

By John N. Murphy

In fiscal 1996, the US Congress directed that the US Bureau of Mines (USBM) be closed. Certain functions were reassigned to other agencies. The remaining employees were separated and the unoccupied sites were decommissioned. As a result, 12 locations were closed and about 1,200 employees were terminated in March 1996. About 600 employees at five locations were reassigned to other federal agencies. This article provides a summary of the continuing functions, the agencies involved and the points of contact for each continuing function. The functions that were discontinued are also identified. The functions that have been maintained and transferred to other agencies are: ? Portions of USBM's Mineral Information and Analysis program formerly conducted in Washington, DC and Denver, CO were assigned to the US Geological Survey (USGS). ? The Mineral Land Assessment program in Alaska (Anchorage and Juneau) was transferred to the US Bureau of Land Management (BLM). ? The Health and Safety Research program in Pittsburgh, PA and Spokane, WA was reassigned on an interim basis to the US Department of Energy (DOE). In fiscal year 1997, it was permanently assigned to the National Institute for Occupational Safety and Health (NIOSH). NIOSH is part of the Centers for Disease Control and Prevention within the US Department of Health and Human Services. ? Environmental Research at Pittsburgh, PA was assigned to DOE. ? Materials Research at Albany, OR was assigned to DOE. ? The helium program was assigned to BLM, where it will be managed pending privatization. ? Coal and noncoal mine maps were transferred to the Office of Surface Mining Reclamation and Enforcement (OSMRE). The following locations were closed: ? Research centers in Denver, CO; Minneapolis, MN; Reno, NV; Rolla, MO; Salt Lake City, UT and Tuscaloosa, AL. ? Field operations centers in Denver, CO and Spokane, WA. ? Washington, DC headquarters office. To provide a concise picture of all of the affected functions, the following is a synopsis of the USBM program functions and facilities immediately before the closure. There were two principal programs: information and analysis, and research.

Jan 1, 1997

By Edmond Donovan, O&apos

With the increase in complexity of conveyor systems and the inexorable demand for more capacity and availability, the ability of designers to accurately predict performance is becoming increasingly important. Dynamic analysis techniques for modelling wave mechanics in conveyors are finding increased applications. Unfortunately, the reliability of these modelling techniques is dependent on a thorough understanding of the performance characteristics of the components that make up the system. These characteristics include such things as response rate, hysteresis and efficiency. Some parameters such as idler rolling resistance can be easily quantified by measurement. More complicated drive parameters are difficult or impossible to measure, particularly in large horse-power equipment. One method of quantifying or at least bracketing the performance envelope of complicated pieces of equipment is to construct a mathematical model. This can be done quickly and economically, and the influence of various parameters can be determined. This paper sets out to demonstrate by example the usefulness of this technique in gaining an understanding of complicated systems. The model is developed and the influence of a number of variables are examined.

Jan 1, 1996

By Adrian Brown

Groundwater inflow and impacts have become major aspects in the permitting and operation of many gold mines. First, the hydrothermal or placer genesis of many of the orebodies being investigated or produced today almost guarantees that mines will be "wet", involving groundwater control as part of operations. Second, the style of ore deposition a1 so often involves a1teration of the host rock, resulting in relatively weak, low permeabi1ity materials that require extensive groundwater pressure control for stable mining. Third, the location of many mines in arid areas guarantees that impacts on water resources will be matters of key focus during permitting and operation. However, groundwater control and protection is a technically difficult area and often involves managerial decisions and activities that do not fit comfortably into traditional mining. In an attempt to overcome some of these difficulties, this paper provides a guide to mine managers and hydrologists as to appropriate strategies for designing, setting up, operating, and evaluating groundwater programs at gold mines that get the job done and are cost effective.

Jan 1, 1988

By R. Hogg, A. C. Maffei, D. T. Ray

Based on standard population balance models for agglomeration and size reduction processes, a simplified model has been developed to describe simultaneous growth and breakage in the flocculation of agitated suspensions. The results of semi-batch flocculation tests have been used for estimation of the model parameters and empirical relationships have been obtained to describe the effects of process variables and to establish scale-up criteria. Application of the model to the design, operation and control of continuous flocculation processes is discussed.

Jan 1, 1990

By H. Reginald Hardy, Maochen Ge

Data analysis is one of the most important steps required for the successful application of the acoustic emission/ microseismic (AE/MS) technique. A dedicated computer software package to analyze acoustic emission/ microseismic data associated with field applications in the geotechnical area has been developed recently at Penn State University. This paper addresses the major features and applications of this computer software package.

Jan 1, 1986

By Romeo S. Jurani

Yucca Mountain, located in Southern Nevada approximately 160 krn northwest of Las Vegas, is currently the site of intensive surfacebased and underground investigations. The investigations are required to determine if the site is suitable for long term isolation of the Nation's high level nuclear waste inventory. A major component of the program is the Exploratory Studies Facility, or ESF. The ESF, when completed, will consist of approximately 25,600 meters of tunnels and drifts. The network of tunnels and drifts (Figure 1) will house and support a wide array of testing programs conceived to provide physical information about the site. Information on geologic, geomechanical, and hydrologic data will be used in the repository design if the site is found suitable. Besides a few special requirements, the general ESF ventilation criteria during construction are similar to that of commercial tunneling and mining operations. The minimum air velocity at the Tunnel Boring Machine (TBM) and other active mining faces is 0.51 meter per second (m/s) (100 feet per minute [fpm]). Airways, estimated leakages and ventilation controls are converted into equivalent resistances for input to mine ventilation network computer simulations. VNETPC Version 3.1 computer software is used to generate the ventilation models for optimized system design and component selection. Subsequently, actual performance of the ventilation system will be verified and validated to comply with applicable nuclear regulatory quality assurance requirements. Dust control in the ESF is dependent on effective dust collection, enclosure, and airflow dilution. Minimum use of water, as feasible, is necessary to avoid adding moisture to the potential repository horizon. The limitation of water use for test drilling and TBM operation, and the rigid compliance with applicable federal and state regulations, make the ESF a ventilation design challenge.

Jan 1, 1995

By Khosrow Bakhtar, Robert E. Cameron, Arfon H. Jones

The use of rock simulators in rock mechanics research greatly expands the scope of the problems that can be investigated with physical models. However, the exact reproduction of full scale conditions, or absolute simulitude, is not obtainable on a small scale model. For this to be possible, the scales of length, time, and pressure (or mass) must be changed without altering the theoretical equations that describe the behavior of materials concerned. In using rock simulants for physical modeling of structures designed in rock, the geometry of full scale structure is reduced to a size suitable for the available testing machine. This will require the strength related properties to be scaled down. Simulation should be representative of the in situ conditions. Complete simulation will require that friction parameters and the stress ratios be matched exactly between prototype and model. The procedure involved in application of physical modeling for rock mechanics research is discussed in the following pages. Background, theoretical approach, and anticipated benefits to the research community are also elaborated.

Jan 1, 1986

By William S. Eaton

Managing a mine or mineral processing operation in today's environment presents many unique challenges to mining companies. In recent years, headlines around the world have publicized major incidents such as those associated with the Marcopper Mine in the Philippines, the cyanide release in Guyana from the Omai gold mine and numerous other mishaps associated with mining. These notable upsets were due to engineered system failures, either during normal operations or as a result of uncontrollable events. There fore, many mining firms are attempting to assess their overall risks and establish some priority for expenditure of limited operational and environmental budgets. Failure of an engineered component can have dire operational consequences that affect profitability until repair or replacement can be completed. In addition, there may be significant environmental consequences associated with the engineered system failure. This, too, may affect profitability for an extended time or even the viability of an operation. An engineered risk assessment (ERA) can support a mining company's efforts to cost effectively manage environmental risks associated with the operation of its facilities. The ERA approach also provides information about the current condition of engineered systems. This ERA approach provides a systematic review of the risks of an engineered system failure and the possible associated environmental consequences at mining company facilities. This approach has been successfully applied to many industries and types of engineered systems (Barneich et al, 1996; Whitman, 1984; Power and Tomkins, 1974; Keeney, Nair, and Kulkarni, 1979). This approach evaluates all mining and mineral processing facilities located at a single site and compares them with similar facilities located at multiple mine sites. The ERA approach has been applied to a mining, milling, smelting, leaching and refining operations. These assessments can be part of a comprehensive environmental program to aid in the recognition and cost effective management of the potential environmental risks associated with the operation of facilities. ERA results support plan-

Jan 1, 1997

By Jun Li, Marc Le Vier, Rong Yu Wan, Jan D. Miller

The hydrometallurgical treatment of gold and silver ores by ammoniacal thiosulfate solutions in the presence of a copper catalyst has been actively studied in recent years. Such a process strategy is very attractive due to the low toxicity of the lixiviant and the efficient recovery of the precious metals from difficult-to-treat ores. Important features of the ammoniacal thiosulfate system for the recovery of precious metals from various sources are reviewed in this paper, including leaching, metal recovery, and system stability.

Jan 1, 1995

By R. Pazhianur

Many investigators conducted surface force measurements between hydrophobic surfaces in water, and observed attractive force that was substantially stronger than the van der Waals attractive force. The excess force was appropriately referred to as “hydrophobic force”, for which many different theories have been put forth by numerous investigators. In an earlier publication (Yoon and Ravishankar, 1996), it was suggested that the hydrophobic force maybe due to the interaction between the large dipoles created by the surfactants adsorbing on solid surfaces in patches (or domains). In the present work, a mathematical model has been developed to further elaborate the theory.

Jan 1, 2003

By Peri Mehling, Allister Brown

Environmental regulations concerning the processing of gold ores and the treatment and disposal of spent process solutions range from rigid standards in some locations to site specific options in several other jurisdictions. This paper examines the regulations and policies in two North American jurisdictions. Emphasis will be placed on the mill process and waste stream treatment and disposal, and implications for environmental impacts. Case examples of mine licence requirements will be discussed, with brief descriptions of individual treatment and disposal systems. Policies and environ- mental regulations within each jurisdiction will be examined in terms of potential environmental protection.

Jan 1, 1987

By P. E. Nielsen, T. L. Loga, B. B. Mauko

A numerical model is presented which simulates the dynamic fracturing process for a circular geometry fracture in a uniform stress medium. The dependence of crack aperture and net pressure in the crack upon various dominant parameters of the fracturing process is discussed. An analysis of a 75% nitrogen foam fracture in a coal seam at 5600 feet (1707 m) is also presented. The analysis is based upon the discussed parametric trends, the job records of treatment parameters, and a Nolte plot of net downhole pressure. It is interpreted that fracturing with water, in pre-foam fracture pump tests, resulted in significant fracture height growth. However, the subsequent foam fracture had reduced height growth due to the high effective viscosity of the foam and due to the higher magnitudes of elastic modulus and stress in the bounding rock strata with respect to the coal.

Jan 1, 1986

By R. L. Grayson

In 1995, the United States Congress abolished the Bureau of Mines in the US Department of Interior. But Congress preserved the safety and health research functions being performed at the Pittsburgh and Spokane Research Centers. These functions were transitionally housed in the US Department of Energy before permanently merging with the National Institute for Occupational Safety and Health (NIOSH), Department of Health and Human Services, in October 1996. Since the rnerger of the former Bureau of Mines with NIOSH, there has been an active evaluation of ongoing research activities, significant interaction with stakeholders, and the development of a process leading to "data-informed" priority setting. This paper reviews the current surveillance information concerning the level of injury and disease from mining work and discusses how research priorities are evolving to improve the contribution of research to the prevention of injury and disease.

Jan 1, 2000

By Paul H. Lu

This paper proposes a novel method, "integrity factor approach," of mine-pillar stability evaluation based on in situ triaxial-loading measurement. The pillar integrity factor is defined as the quotient resulting from division of integrated total pillar strength across the critical dimension by the integrated total pillar load across the same dimension. The integrity factor is dynamic, while the conventional safety factor is static. With this approach, the pillar stability can be evaluated at any stage of mining progress during panel operation. It automatically considers the progressive failure of the pillar and post-failure strength without the need to clearly define the boundary between yielded and intact zones of the pillar. Based on two case studies, the integrity factor approach is shown to be a practical, effective technique for evaluating stability of conventionally designed pillars. It is suggested that a more realistic estimate of in situ pillar strength could be made based on the combination of in situ triaxial-loading measurements and laboratory true triaxial compression tests, rather than through the traditional combination of biaxial-loading measurements and conventional triaxial compression tests.

Jan 1, 1986

By B. J. Sauer

Misapplication of ac induction motors for mine crusher and mill applications has long been a frustration for the driven equipment supplier and the mine operator. Proper selection of ac induction motors is critical to providing efficient production. This paper focuses on the selection of ac induction motors for gyratory crusher, conecrusher and grinding mill applications. The criteria for motor selection includes: proper enclosure, driven equipment torque requirements, bearing life, temperature rise, starting requirements, ambient temperature, altitude and accessory requirements.

Jan 1, 2002

By Pradip

The selection, testing, and commercial utilization of flotation reagents is best carried out in stages through microflotation tests on pure minerals and their synthetic mixtures followed by bench-scale batch flotation tests on the ore. A systematic approach to quantitatively evaluate different reagents, in particular, through the analysis of batch flotation data, has been presented in this paper. It is recommended that the reagents are compared both in terms of their performance with respect to the recovery-time as well as the recovery-grade plots. While the former describes the kinetic aspects of reagent interaction, the latter is a measure of its selectivity for a particular separation problem.

Jan 1, 1987

By Raj K. Rajamani, M. K. Abd El-Rehman

The planetary mill is very much suited for the ultra-fine grinding of mineral fillers. Ultra-fine grinding here refers to grinding powders to a size range 5-1 0 rnicrons. Such powders enhance the quality of the final product. The operation of a specially built planetary mill is described. It is shown that a target size of 5 rnicrons can be reached in a few hours using the dual drive planetary mill. A centrifugal field of 37G is generated by the gyration arm of the mill. The design allows the desired setting of canister critical speed. The ultra-fine grinding of alumina, titanium dioxide, hematite, magnetite, kaolin and silicon carbide are described. Also, the continuous operation of the mill is shown.

Jan 1, 2003