Search Documents

By Pierre M. Matheron

TRANSMANCHE-LINK is responsible for designing, developing and implementing the project for a fixed link under the English Channel, comprising two running tunnels of diameter 7.6 metres and a service tunnel of diameter 4.8 metres. The three tunnels will all be 50 km long, with 37 km bored through chalk marl at a depth of 40 metres under the sea bed. The tunnels will be driven from both sides of the channel from intermediate addits above the coastline on either side with a 55 m access shaft at Sangatte in France and two "descenderies" or inclined tunnels addits and a shaft at Shakespeare Cliff on the English side. A total of eleven tunnel boring machines will drive the 150 km of tunnels. The major part of the tunnel linings will be built of precast reinforced concrete segments, and two plants have been specially built to produce the necessary 725,000 segments. Seven million cubic metres will be evacuated on wagons along the tunnels and then lifted by belt conveyor on the English side, and by hydraulic mucking from the bottom on the French side. Preliminary work started early in 1987 with manufacture of the first boring machines, construction of five precasting plants, boring of the Sangatte shaft in preparation of the Shakespeare Cliff entrances. The principal project dates are :

Jan 1, 1987

By V. Matthews

"INTRODUCTION Typical grinding electrification requirements are defined by high power, constant torque and slow speed. Dual pinion mills also include a need for tight tolerances in torque between the two motors, to avoid overloading any single motor. Standard induction (asynchronous) motors have often been used but only in combination with mechanical gearboxes (reducers), required to reduce process speed to the correct level for mill pinions. The gearbox introduces added system complexity, capital cost, maintenance and energy cost due to mechanical losses. SYNCHRONOUS AND ASYNCHRONOUS MOTORS Elimination of the gearbox requires a motor designed to operate at a very low speed (rpm). Traditionally, mill motor requirements were best served by synchronous motors. The benefits of synchronous motors include- • Higher Efficiency (no conductor losses in rotor) • Very high power at low speed • Flexible Power factor (leading or lagging) • Constant speed (not load dependent) • More accurate speed control Synchronous motor cost is higher due to construction complexity, need for exciter and excitation panel, brushes, brush lifters. Figure 1 represents the equivalent circuit for a synchronous motor.Asynchronous motors, also known as squirrel cage induction motors, are singly excited, per Figure 2, the resulting equivalency circuit is less complex and only in need of a single voltage source.Commonly, a DC voltage supply is connected to the rotor (both physically and electrically) via brushes. The DC voltage enables the production of flux in a single direction. The brushes are connected to rings. The slip rings encircle the rotor but are insulated from the rotor. The slip rings are connected to a rotor winding known as a field winding. On large motors, brushless exciters are often used. A brushless exciter is a small AC generator whose field circuits are mounted on the stator and armature circuits are mounted on the rotor shaft. The exciter generator’s 3-phase output is rectified to DC by a 3-phase rectifier (mounted on the shaft) and fed into the main DC field circuit. It is possible to adjust the field current on the main machine by controlling the small DC field current of the exciter generator (located on the stator). [1] Brushless synchronous motors are often preferred over the traditional brush design but introduce additional complexity to motor construction in the form of additional windings and rectifiers comprising the excitation circuit. It stands to reason that because of the additional complexity, a synchronous motor will be higher in cost than an equally rated asynchronous induction machine."

Jan 1, 2015

By J. P. Wilson

The Tessenderlo-Kerley Leach process has been shown to be effective in the removal of residual copper from molybdenite concentrates. Concentrates of varying mineralogy, including those containing relatively large amounts of chalcopyrite, have been successfully leached on laboratory and pilot plant scales. The lixiviant system is ammonia and ammonium bisulfite with air / oxygen addition. An abrasive is added which greatly enhances the kinetics, and it is subsequently screened out and reused. The dissolved copper is easily recovered using existing technology. Extraction profiles, reagent consumptions, and mineralogical data are presented.

Jan 1, 1999

By William Mayrsohn

INTRODUCTION The net smelter return (NSR) calculations made on various smelter-refiner alternatives, is usually done by taking the gross metal value less metal deductions, smelter-refiner charges and transportation-insurance costs. An important further step in the calculations is the financial charges imputed by refining time, transportation delays, to the time gold is returned (if tolled) or paid for if bought by the refiner. Metal that is priced in advance of payment also requires a forward premium that the mine may or may not be getting. This is a hidden cost that is often omitted from the calculations. Segmentation of each of the above costs are vital to see where improvements can be made through negotiations, better choice of metal pricing or transportation alternatives. BASIC NSR CALCULATIONS SMELTER-REFINER CHARGES Payable Metals - Treatment Refining Charges: Since these can vary from one smelter to another, the effect of a $25 per ounce price increase/decrease should be calculated and kept in mind. This effect is compared to differences in refining/treatment charge and a total smelter/refiner cost on a cost per ounce of dore, gold, or a dry ton of concentrate. Transportation - Insurance: Research has to be done on transportation alternatives perhaps with some assistance from the smelters, railroads or trucking companies. For dore, the U.S. postal service is viable and inexpensive. For railroads, deal with the regional office ie., B&N El Paso, if production warrants regular bulk shipments. Spot rates tend to be higher. A small mine producing concentrates usually goes to the nearest smelter due to extremely high transportation costs. Here is where a refiner can help. Insurance-Quotes for rates on dore/ concentrates are easily obtainable, but the mine has to shop for the best rates. Your insurance broker is the best source of this information. Differences between Mine and Smelter/Refiners Metal losses can be caused by the following: - Concentrate dry weight differences caused by moisture determination or faulty scales (often at the mine). - Sample bias by poor preparation practices on either side ie., grinding of the sample removing gold; or a poorly mixed concentrate. Dore bullion has no such difficulties.

Jan 1, 1987

By M. A. Gibson

Ilmenite-rich lunar deposits can be converted to liquid oxygen to support lunar base operations and space transportation propulsion needs by a Carbotek-developed process. Iron oxide in ilmenite is reduced at elevated temperatures by hydrogen in a fluidized-bed reactor to water vapor which is electrolyzed to product oxygen and recycle hydrogen. Reaction rate, thermodynamic equilibrium, and lunar-gravity fluidization behavior are key factors which have been considered. Fluid-solids behavior has been modeled from data taken at lunar gravity conditions aboard NASA KC-135 flights. Large-scale pilot plant operations are planned to complete the development.

Jan 1, 1991

By R. Benito, J. Lopez, H. Gamarra

This article describes three practical applications of the Hill of Value (HoV) methodology within different stages of strategic planning for open-pit mining operations and projects. In the pursuit of optimal mine planning, this study establishes a comprehensive case study during the (i)design phase, by refining key parameters for efficient decisionmaking. (ii)production planning, where the HoV is used to define achievable production rates, enhancing operational effectiveness through a nuanced consideration of mining and processing capacities. (iii)Additionally, the study introduces a conceptual framework for orchestrating the optimal sequence of multiple pits during the planning phase, with a focus on maximizing project value.

Feb 1, 2024

By J. M. Mutmansky

Introduction Since the Hardy Cross numerical algorithm was applied to the solution of mine ventilation networks, numerous developments have taken place in ventilation network analysis procedures. The Newton-Raphson method, the linear theory method and the second-order approximation method are three of the additional approaches that have been applied. The efficiency of a ventilation network analysis procedure depends not only on the method of solving the system of equations derived from ventilation networks but also on the method of deriving the equations through selection of the meshes. This paper investigates the impacts of three mesh selection methods on the efficiencies of four ventilation network procedures. The minimum-resistance spanning tree method is the most popular procedure for selecting meshes. The shortest-path method was suggested by Epp and Fowler (1970) for improvement of the Newton-Raphson method. The minimum-resistance-path method is suggested here as the third method of selecting meshes. The effects of these three methods on the Hardy Cross method, the Newton-Raphson method, the linear theory method and the second-order approximation method are analyzed in this paper. These network analysis methods have been summarized in the paper by Kim and Mutmansky (1991). Mesh selection methods A procedure for mine ventilation network solution based on mesh equations typically consists of two steps: • the mesh selection step and • the network solution step. The mesh selection step establishes a set of independent equations to solve the network. The resulting equations are nonlinear. One method of solving nonlinear equations is to linearize the equations and iteratively solve these linear equations. The four analysis methods previously discussed in this paper use this approach. The linear equations required for solution can be written in matrix form as: P•dQ = dF (1) where P is the pseudo-resistance matrix, Q is the quantity matrix, and F is the Jacobian matrix (Kim and Mutmansky, 1991). The efficiency of the solution method depends on the characteristics of the P matrix, which in turn depend on the method of selecting meshes. To understand the impacts of the mesh selection methods on the efficiency of the ventilation network analysis procedures, the characteristics of the P matrix must be understood first. The diagonal elements of the P matrix, m in number, are the sums of the pseudo-resistances of the branches contained in the m meshes necessary for solution. The off-diagonal elements are the sums of the pseudo-resistances of the branches shared by two meshes. For example, P12 (first row, second column element of the P matrix) is the sum of the pseudo-resistances of the branches common to mesh 1 and mesh 2. When solving the system of equations expressed in Eq. (1), three of the iterative procedures (the Newton-Raphson, the linear theory and the second-order approximation methods) use the direct factorization method (Burden and Faires, 1985) on the P matrix. When the direct factorization method is used, the computational efficiency is enhanced by larger diagonal elements and a sparser P matrix. Generally, the sparsity of the P matrix is more important than the size of the diagonal elements. There is no known mathematical method of predicting the efficiency of these procedures, but heuristic methods can be used to study the efficiency. The Hardy Cross algorithm applies the Gauss-Seidel method of splitting the P matrix and applies the Newton-Raphson procedure. The efficiency of the Hardy Cross method depends on the spectral radius of the matrix[[D-L]-1U], where D is the diagonal, L is the lower triangle and U is the upper triangle of the P matrix for the Newton-Raphson method (Ortega, 1972). The smaller the value of the spectral radius, the faster the convergence. As with the other three methods, larger diagonal elements and a sparser matrix aid in faster convergence. With the Hardy Cross method, however, the size of the diagonal elements is more important than the sparsity of the matrix. Remembering that each of the diagonal elements of the P matrix is the sum of the pseudo-resistances of the branches in a mesh and that each off-diagonal element is the sum of the pseudo-resistances of the branches shared by two different meshes, the following strategies can be used: • Avoid having branches with larger resistance values shared by multiple meshes. This increases the size of the diagonal elements and reduces the chance of off-diagonal elements being large.

Jan 1, 1993

By Felicia F. Peng

Flotation process is particle hydrophobic surface-based separation technique. To improve the essential flotation steps of collision and attachment, and reduce detachment probabilities between air bubbles and hydrophobic particles, a selectively designed cavitaion venture-tube can be used to generate very high numbers of pico-nano bubbles to flotation column. Fully embraced by those high numbers of tiny bubbles, hydrophobic particles are readily attracting those tiny bubbles to their surfaces. The results of column flotation of Pittsburgh No.8 seam coal are obtained in a 50 cm ID and 162cm height flotation column equipped with static-mixer and cavitation-venture tube, using kerosene as collector and MIBC as frother. Design of experiment procedure combined with statistical two-stepwise analysis method are applied and attempted to made the optimizing the grade and recovery. The effect of independent variables on response has been explained. Combustible material recovery of 85-90% at clean coal product of 10-11 % ash are obtained from feed of 29.6% ash, with reduced amount of frother and collector than that used in conventional column flotation. The column flotation process utilizing the pico-nanobubbles can also be extended to the lower limit and upper limit of particle size ranges for better recovery minus 75 µm and 300-600 µm, respectively.

Jan 1, 2013

By C. M. Sliepcevich

This paper is a brief status summary of investigations by the authors over the past decade to develop a continuous process for recovering' high purity metal powder from pregnant solutions by gaseous reduction at elevated temperatures and pressures. Although these studies included extraction of other metals such as nickel, silver, and gold, this presentation will be confined to the hydrogen reduction of acidic and ammoniacal solutions of copper. The continuous hydrogen reduction process (CHR) described herein enjoys the environmental advantages of other hydrometallurgical processes but, in addition, provides a substantial benefit in fuel economy over competing processes. As was recognized by Schaufelberger in 1956, for a given amount of fuel a continuous hydrogen reduction process has the potential for producing four to six times as much metal as an electrolysis process (1). Although hydrogen reduction of metal salt solutions has been known for more than a century, extensive development work leading to commercialization was not initiated until the 1950's. Since then, commercial applications relative to other extractive techniques have been minor and have been confined to batch or to continuous, completely-mixed autoclaves. By contrast, the process described herein utilizes a continuous, tubular reactor which is operated in modified plug flow so that only limited and localized backmixing occurs. Thus, gradients in concentration, temperature, and pressure exist over the length of the reactor, the presence of which can be utilized to advantage for achieving high conversions and product quality (2, 3).

Jan 1, 1975

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By A. Pinches, R. Winby, P. J. van Staden, M. K. Rhodes, P. C. Miller

This paper is a progress report on the commercialization of using bioleaching for base-metal concentrates. The paper focuses on bioleach processes for recovering copper from chalcopyrite and nickel/cobalt from pentlandite/pyrrhotite. Data is discussed from pilot-plant trials in which an overall recovery >95% was obtained for the bioleaching of copper from chalcopyrite. The pilot plant was operated in closed circuit with solvent extraction and electrowinning circuits for final metal recovery. For the bioleaching of nickel and cobalt from pentlandite/pyrrhotite, an overall recovery of 97% was achieved. Precipitation routines were used to produce a final nickel/cobalt product. The pilot plants were capable of treating a few kilograms of concentrate per day. Prominent features in the design of a 1-t/day (1.1-stpd) copper-bioleach demonstration plant for the treatment of chalcopyrite concentrate are discussed. The plant, which is now under design, will be constructed and operated based on the results obtained from the laboratory pilot-plant campaigns. Issues of scale-up for the demonstration plant, together with integration into upstream and downstream processing, are also addressed. Independently derived capital and operating costs are presented for a possible commercial plant. These cost studies indicate the principle economic issues in considering the application of bioleaching to the extraction of base metals. The benefits of bioleaching complex concentrates that are not amenable to physical beneficiation and economic treatment by conventional smelting are highlighted. Issues, such as the environmental aspects, that illustrate the benefits of bioleach technology are given.

Jan 1, 2000

By Alan R. Grant

Interpretation of presently available geological information indicates that most of the periods of significant metal deposition in the Washington Cascades Range are, at least in part, genetically related to late Cretaceous -Tertiary intrusive episodes. Chemically, the most favorable environment for base metal deposition is high in potassium. Characterizing the advanced stages of these chemical alteration conditions are the silicate mineral assemblages orthoclase and/or secondary biotite. Wall rock alteration includes both deuteric and hydrothermal processes, the intensity of which primarily depends upon the degree of fracturing in the country rock prior to the introduction of secondary material. Broadly speaking, the primary physical controls for the distribution and concentration of sulfides appear to be a series of structural couples involving both northwest (paralleling regional trends) and northeast--striking systems. Meaningful base metal exploration in the Washington Cascades demands a basic understanding of the various geologic factors related to the distribution of the sulfide deposits. Any geologist contemplating Cascade work should be well grounded in the fundamental concepts of petrology and structure.as these constitute two of his most beneficial aids. The acquisition of the detailed data necessary for this understanding may seem a bit academic, yet it has been demonstrated in numerous instances that a fair economic appraisal of a particular property or mining district depends primarily upon the ability of the geologist to recognize the subtle environmental differences which could lead to the discovery of a major ore deposit.

Jan 1, 1971

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By S. K. Mukherjee, M. M. Singh, N. I. Jayaramn

In underground mining operations, ventilation and water sprays are the common methods of controlling dust. In recent years, there has been a proliferation of technical literature dealing with water sprays for dust control. However, guidelines for the design of an effective water spray system have not been presented to the mining industry. This paper recommends guidelines for water spray systems to control dust in underground mining operations. These guidelines suggest type, number, location, and orientation of nozzles; desirable operating water pressure; and associated filtration system.

Jan 1, 1987

By E. Pardo-Igúzquiza

Most mining applications of geostatistical simulation are to the simulation of quantitative variables, such as grade. In many instances the occurrence of quantitative variables and the values they take are controlled, at least partially, by qualitative, or categorical, variables. Examples include quartz-vein controlled gold orebodies and stratigraphic silver/lead/zinc deposits. In these cases a realistic simulation must include geological controls on the spatial distribution of the simulated quantitative variables. This paper describes extensions to, and algorithms for, the truncated plurigausian method of simulating categorical variables. The categorical variables are modelled as indicator random functions that represent the presence/absence of the variable at spatial locations. Stochastic images of the distributions are obtained by truncation of realisations of two Gaussian random functions simulated at the same locations. Parameters required are the thresholds for truncation of the Gaussian variables and the covariance structure of each Gaussian random function. These parameters are estimated from the experimental proportions of each variable and indicator direct and cross semi-variograms. A detailed case study is shown in order to illustrate the procedure, to discuss the results and to present the algorithms for plurigaussian simulation.

Jan 1, 2002

By P. C. Thakur

Mine productivity, measured by the output of minerals per manshift, depends on a number of factors including physical conditions of the minable seam, type of mining equipment, management techniques, worker attitudes and governing jaws and regulations. The greatest scope of improving productivity lies, perhaps, in modifying physical conditions to an advantage and using highly productive equipment. In the case of coal mines, increased productivity can be achieved by (i) obtaining prior knowledge of the mineable property, e.g., the grade and thickness of, the coal seam, presence of sand channels, faults, etc., (ii) eliminating conditions that hamper production, e.g., high emissions of methane and water, and (iii) using more productive mining techniques. Conoco/Consol's (Conoco Inc. and Consolidation! bal Company, a fully-owned subsidiary) horizontal drilling system was developed with the hove objectives in mind. It can drill 75 to 1001 in diameter boreholes to depths of more than 600 1 and maintain the borehole in a preselected horizon. Such boreholes can be utilized for premining exploration of the coal seam, for removing methane and water and in devising mining techniques with high productivity. The purpose of this paper is to describe the horizontal drilling system briefly and to discuss its applications in the above-mentioned- areas.

Jan 1, 1980

By Steven J. Kirk

In the past decade, many hardrock surface miners have revegetated dumps and tailings ponds to allow those waste disposal areas to blend more easily with the surrounding landscapes. Efforts have also been made to more creatively use the flat land resulting from the disposal of overburden and tailings. However, the mines which serve the best post-mining land uses are those that have been preplanned to incorporate such end uses. To more fully explore such a philosophy, interdisciplinary team from The University of Arizona conducted a study during 1974 and 1975 of six open pit copper mines in the Santa Cruz River Basin south of Tucson, Arizona for the purpose of investigating both interim and end-use possibilities for mine waste disposal areas. Among other reasons for the study, it was felt that alternatives for such waste areas would be more socially acceptable than barren dumps or tailings ponds. The team, known as the Mines Project Group, consisted of architects, engineers, and hydrologists. As it would have been economically infeasible to move the existing waste rock dumps or tailings ponds, preplanning was limited to the disposal of waste generated after the inception of the project. To better present their concepts, architecture professors Kenneth Clark and Fred Matter constructed a large-scale cardboard relief model of the mines and the surrounding Santa Cruz River Valley (1). The model was built at a scale of 1:12 000 (1 in = 1000 ft) with 30.48 m (100 ft) contour intervals and covered an area of 40.23 km by 32.18 km (25 miles by 20 miles) in scaled area. The mines being studied were cut into the model, but the proposed waste dumps and tailings ponds were built separately so different disposal configurations could be evaluated.

Jan 1, 1980

By Margaret Armstrong, Arne Berckmans

The longterm aim of this research project is to find fast ways of simulating the recoverable reserves of a deposit for input into financial Monte Carlo simulations without having to conditionally simulate the whole orebody many times. The first step in this re- search is to visualize and quantify the ore tonnage T and the metal quantity Q above an arbitrary cutoff z. This paper presents detailed results for one specific distribution, the lognormal. These lead to a suggestion of a fast way of simulating QTz curves.

Jan 1, 1996

By J. A. Herbst, Y. C. Lo

An attempt has been made to parameterize the population balance model for a ball mill based on measurements of the elementary breakage process obtained using an ultrafast load cell device. Detailed insight obtained concerning the fragmentation of particle assemblies with the ultrafast load cell leads to a better understanding of ball mill grinding. The ball mill breakage function and specific selection function are derived from an average single event representing the multiple breakage events which occur in ball mill grinding. Since both the breakage function and the specific selection function depend on the loading mode in the mill, predictions of breakage mechanisms in ball mills are possible by using data obtained in various elementary loading modes. The application of this model to the description of batch ball milling behavior has resulted in reasonably accurate predictions of product size distributions for various energy inputs.

Jan 1, 1992

By Z. T. Bieniawski, Nicholson G. A.

This paper describes an empirical constitutive model for underground excavations in rock which equates the deformation modulus to the ratio of the principal stress difference to the major principal strain. The model requires failure criteria which define both the stress difference at failure and strain as a function, in part, of rock mass classification ratings (i.e. Bieniawski's RMR and Barton, Lien and Lunde's Q). Available failure criterion allows reasonable estimates of the stress difference for intact rock as well as rock mass. However, a suitable failure criterion for estimating strains at failure for rock was not available. Toward this end, this paper describes the development of an empirical criteria for defining strain at failure for intact rock as well as methodology for developing similar criteria for rock mass.

Jan 1, 1986