Search Documents

By D. C. McIntire

The Homer City Station, jointly owned by New York State Electric and Gas Corporation and Pennsylvania Electric Company is a three unit coal fired station. The first two units were put into commercial operation in 1969; the third unit became commercial in 1977. Units 1 and 2 are subject to the Pennsylvania State Implementation Plan (SIP) emission limit of 3.7 pounds of S02 per million BTU. Unit 3, having started construction later, is subject to the Clean Air Act, New Source Performance Standards emission levels of 1.2 pounds of 50-2 per million BTU.

Jan 1, 1988

By Collin L. Stewart

Published subsidence data for the western United States is limited in comparison with data for the east. This paper summarizes the results of a subsidence monitoring program above two longwall panels at the Foidel Creek Mine located in northwest Colorado. The monitoring area is characterized by overburden ranging from 1000 ft to 1100 ft in thickness. The surface slope parallels the dip of the bedding at approximately 5 deg. Average mining height is 9 ft. Smax averaged 3.4 ft. Draw angles averaged 15 deg for up-dip ribsides and 19 deg for down-dip ribsides. A site-specific profile function is developed from the data.

Jan 1, 1986

By Neil D. Donnell, O&apos

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1984

By M. Liu

In-situ soil washing using surfactants shows great potential to remove hydrophobic organics from subsurface environment. Lab scale soil washing experiment were performed using Sodium Dodecylsulfate (SDS), an anionic surfactant, and anthracene, a highly hydrophobic compound. The results of this research show that solubility of anthracene increases linearly with an increase in SDS concentration above the critical micelle concentration. Furthermore, SDS can be effective in removing anthracene from contaminated sand.

Jan 1, 1992

By Jack M. Jodrey, Neil D. O’Donnell, R. A. Metz

Bituminous sands of the Lower Cretaceous McMurray Formation in northern Alberta constitute the ore for the surface mining operation at Syncrude Canada Ltd. These sediments represent a complex succession of fluvial, estuarine and marine depositional environments. Grade prediction is realized through a combination of geological interpretation, computer modeling, and reference to past mining experience. Accurate forecasts of feed grade permit reliable predictions of volumes for removal to meet budgeted synthetic crude oil production. This planning facilitates efficient allocation of mining equipment and resources. The feed grade to the Extraction Plant is monitored at various points along the delivery system.

Jan 1, 1992

By Maurice Rey

The copper segregation process is designed to concentrate oxidized copper ores or mixed sulfide-oxide copper ores which are refractory to normal and cheaper mineral dressing or leaching processes. Such ores contain copper silicates or highly disseminated copper minerals in a gangue not entirely free from limestone or dolomite. Concentra¬tion by flotation is, under these circumstances, not possible and the acid-consuming constituents do not permit acid leaching. A high temperature treatment at 700-800°C, in the presence of a small amount of sodium chloride and of finely divided carbon, concentrates the copper into easily floated metal by a kind of reducing chloridizing roast. The sulfides, if present, are either oxidized in the heating stage and react like oxides or float with the metallic copper in the flotation step. The ores which have the aforementioned characteristics and which are high grade enough to pay for the treatment are scarce, so that the process has only a limited application. Theory of Copper Segregation Sodium chloride, reacting with water vapor and the acid gangue constituents, produces hydrogen chloride which reacts with the copper minerals. The copper is volatilized as cuprous chloride and immedi¬ately reduced on the coal particles by hydrogen emanating from the volatile matter of the coal and from the water-gas reaction. Hydrogen chloride is

Jan 1, 1985

By Rene Padilla, Siyanda B. Mngadi, Gerrie van Aswegen, Peter Stonestreet

While many mine tunnels are developed through ground that must be riddled with the sources of small (and larger) mining induced seismic events, recorded by the mine seismic monitoring systems, we do not see planar discontinuities classified as seismic sources in the geotechnical databases. Here we list criteria that may be useful to identify discontinuities in drill core which are dynamic slip surfaces, parts of mining induced seismic sources. Such shear rupture surfaces in core would generally be powdery, cohesionless, and rough on cm scale. Finely broken rock and rock flour may be found in the core boxes at the discontinuities. Slickensides would be soft (easily destroyed) and kinematically consistent with the local stress field. In some cases, a cross fabric would be present, orthogonal to the slickensides, being the intersections of en-echelon extension fractures, within the dynamic shear zones, with the shear zone walls.

Apr 26, 2022

By E. Watkins, R. Kimutis, H. Dougherty

Gas wells have often intersected mining resources, but unconventional shale well drilling has more recently challenged mines to balance the risk of interaction due to higher pressures and larger quantities of gas. Full extraction mining, such as the longwall method, induces ground movement that may influence the casings if wells are drilled within the mining area. The possibility of a casing shear would lead to the risk of unplanned gas migration into the mine. This has the potential to quickly overcome the ventilation system and reach the explosive range which, if ignited, can have catastrophic consequences on the health and safety of underground workers. The utilization of network software to model mine ventilation is a common practice in the mining industry and can assist with a well breach scenario. This work focuses on a well breach in between two longwall panels after second panel mining with gas entering primarily through the gobs of the adjacent longwall panels. Applying the network software Ventsim, a gob zone and ventilation network were created to better understand the distribution of gas within the mine and the limitations and effectiveness of a ventilation system. The model shows both a transient flow simulation and steady state concentrations throughout the mine ventilation system. Using a standard Pittsburgh coal seam longwall ventilation scheme, we find that the system can dilute a significant inflow of up to 700 cfm of methane.

Mar 2, 2022

By M. Sagisaka

Coal is expected as one of the main energy sources for a long period because of vast deposits. However, two large barriers to utilize it are suggested, i.e. the carbon dioxide emissions and ash disposal. The authors chose principal methods and areas to utilize coal ash and analyzed the environmental impacts caused by the ash treatment considering the source of the ash. According to the analysis based on lifecycle thinking, an optimized ash treatment system can reduce the integrated environmental impact. It suggests that coal can carry out its role for several decades without disturbances from the point of ash treatment.

Jan 1, 2006

By H. Cetin

The availability of coal resources of selected 7.5-minute quadrangles of southwest Indiana was examined in this study. Resources were defined as original coal in place, remaining after mining, and currently available considering land-use and technological restrictions. The amount of coal mined from each study area varies depending on the mining practices of the companies operating within the area. Of the three quadrangle investigations, the available resources range from 50 percent to 79 percent of the original resources. Most of the coal resources under deep-minable category were not available because of technologic restrictions, such as insufficient coal thickness.

Jan 1, 1996

By G. Robert Ganis

The folded Appalachians are a physiographic province of eastern North America extending from Nova Scotia to Alabama. The province strikes through the state of Pennsylvania (see Fig. 1) comprising roughly 20 percent of the state and it is here that the focus of this paper will attend. The province is a thick sedimentary sequence which was compressed into a folded mountain belt by the Appalachian Orogeny which terminated at the end of the Permian. The stratigraphy contains both carbonate and non-carbonate rocks as a reflection of the depositional environment at any specific time and place during the Paleozoic geosynclinal accumulation. Although a great deal of variety and difference exists in the geology from one end to another, a common thread of structural and stratigraphic style exists. Carbonate rocks, limestones and dolomites, comprise a substantial percentage of the total Appalachian stratigraphy and are interbedded with clastic materials such as sandstones, siltstones, and shales. The carbonate rocks are extensively mined and collectively represent a vast economic resource.

Jan 1, 1983

By Michael Brittan

The AARL elution process has recently been introduced to the North American mining industry by Bateman Engineers Inc. The process is described along with its noteworthy features. Design and operating considerations are discussed.

Jan 1, 1998

By Shoung Ouyang, Pinnaduwa H. S. W. Kulatilake

Available literature on the topic is reviewed. Methods are suggested to improve the presently available techniques to perform probabilistic modeling of shear strength parameters for rock discontinuities. The Mohr-Coulomb model and a power law model are used as strength criteria to model shear strength of rock discontinuities. Use of various regression techniques for point estimation of shear strength parameters from direct shear data are discussed. Goodness-of-fit tests for bivariate beta and bivariate normal distributions are developed, and the applicability of them to represent the distribution of shear strength parameters is tested through examples. Both distributions seem to have potential to represent the statistical distribution of strength parameters.

Jan 1, 1986

By John Thella, Edward McNew, Christina Thella, Mends Emmanuel, Pengbo Chu

Ore sorting is an emerging technology in mineral processing that can produce a significant impact on the total mining and processing economics. The technology is capable of preconcentrating an ore based on differences in the mineralogical characteristics, which can include color, brightness, transparency, size, shape, density or near-infrared response. The current practice of conducting an ore sorting test typically requires large amounts of materials to be sent to a commercial testing facility, which is expensive and time-consuming. Here, we present a novel method to simulate commercial ore sorting on a laboratory scale using a rare earth ore.

Jan 1, 2025

By Nobuharu Isago, Atsushi Kusaka, Kosuke Kawata

"Rock tunnels suffered severe damage from recent large earthquakes in Japan, despite the empirical knowledge that tunnels tolerate earthquakes better than surface structures. Seismic design for rock tunnels have therefore become a fascinating subject for many tunnel engineers. However, even basic behavior, including deformation mode and loading magnitude for hard-rock TBM tunnels and conventional ones during earthquake, has not been fully understood due to lack of actual seismic data; while EPB and slurry TBM tunnels take account of seismic design in Japan if needed. This study conducted a dynamic measurement in an actual road tunnel constructed in rock. The strongest aftershock of “the 2011 off the Pacific coast of Tohoku Earthquake” (Mw = 7.1) occurred during the measurement, providing precious data to examine deformation mode of the tunnel. Considering the acquired data, numerical analysis was also performed to calculate loading magnitude to cause fatal fracture of tunnel lining during earthquake.INTRODUCTIONLarge earthquakes can pose serious risks even for rock tunnels, as evidenced by large earthquakes in the past. In the large earthquake in Japan in 2004 (Mw = 6.6), some tunnels suffered severe damage including collapse of their permanent lining (Mashimo 2005), even though the tunnels were constructed in ordinary ground conditions except for fault, fracture zone, portal area, etc. To mitigate such risks, mechanical behavior of tunnel lining during earthquake should be clarified; however, even basic mechanical behavior including load-bearing capacity of the tunnel lining against earthquake is not fully understood.Numerous damage modes were actually observed due to various ground conditions (eg. Wang et al. 2001; Mashimo 2005). Among them, major tunnel damage caused by earthquakes can be grouped into three main modes as shown in Figure 1, excluding extremely unusual conditions such as a tunnel located on a stratum boundary where the stratum stiffness varies significantly. TYPE-I shows flexural failure or crack by bending moment at shoulders; TYPE-II indicates compression failure or flexural compression failure at crown; and TYPE-III illustrates compression failure at sidewall, mainly observed on tunnel that was constructed using steel ribs and lagging method. These damage modes, Type-I, II and III, are predominantly caused by shearing, horizontal compressing and vertical compressing deformations of the surrounding ground, respectively (Kusaka et al. 2011; Asakura et al. 2001)."

Jan 1, 2016

By Leslie S. Halasz

This paper describes the techniques implemented at Randfontein Estates to develop twin-haulages at 'high speed'. An operation which culminated in the world record advance for twin-end multiblast cyclic development in hard abrasive quartzites. A major expansion project was planned for the mine, with the sinking of a third twin-shaft system (to be known as Cooke No. 3), to raise the level of ore production from 3 500 000 to 5 000 000 tonnes per alumm. Subsequent redesign of the proposed shaft system as a single 9 m brattice wall shaft took place, reducing the planned shaft sinking period by 12 months and saving an estimated R 250 000 (U.S. $ 330 000) in sinking costs. The advancement of the Cooke No. 3 Shaft sinking and development programme necessitated a rapid excavation schedule for two interconnecting twin-haulages from the existing Cooke No. 2 twin shaft complex to provide a second means of egress. An early holing between the two shafts would provide significant financial and technical benefits. Pre-development and equipping of shaft pillar excavations would enable a rapid shaft production build up and blocking out of at least one year's ore-reserves.

Jan 1, 1983

By Jan E. Stache

Commercial software programs are being utilized to create and maintain a mine subsidence database in conjunction with the U.S. Bureau of mines research on mine subsidence in Illinois. A three-year survey net of monitored structures in an Illinois subdivision was entered as textual information (attributes), on an existing AutoCAD drawing. These attributes can be optionally displayed on the corresponding drawing or extracted as a text file for import to a database program. The database program, dBASEIV, allows combinations of multiple database files for extensive querying capabilities. Subsurface database files can be merged with surface database files to enhance the effectiveness of surface response analyses in mine subsidence research. The geographic information system (GIS), pcARC/INFO, was chosen to integrate existing AutoCAD drawings and dBASEIV database files into a relational database with a graphical representation. The relational database allows users to update either the graphical representation or the database, with the changes being reflected automatically in its alternate format. The increased capacity, through use of a GIS, to query combinations of database files and have the results reflected graphically has significant potential for expediting mine subsidence research.

Jan 1, 1986

By Purnima A. Shivdasan

The fluorspar deposits at Okorusu, Namibia are closely related to an alkaline igneous ring complex of late Cretaceous age (125±7 Ma). The fluorite ores consist of relatively fine-grained purple replacement fluorite and subsequent coarser grained purple and green vug-filling fluorite crystals. Homogenization temperature measurements for 38 primary fluid inclusions shows that main stage purple to green fluorite crystals were deposited over a temperature range from 166°C to 144°C, and minor late yellow fluorite was deposited at lower temperatures from 132°C to 128'C. Homogenization and freezing temperatures measured for 18 primary fluid inclusions shows that the fluorite-depositing fluids were less saline than MVT ore fluids and overlap the lower temperature range of fluids that deposited epithermal ore deposits. Mining in two open pits (A and B) at Okorusu has gradually provided exposures which reveal that the fluorite orebodies have been emplaced primarily by the preferential replacement of carbonatites. Evidence for the replacement of carbonatite includes: 1) replacement remnants of carbonatite within the fluorite ores, 2) goethite pseudomorphs after the carbonatite minerals, pyroxene, pyrrhotite, and magnetite that are disseminated in the fluorite ores, 3) partial replacement by fluorite of a titaniferous magnetite rimmed carbonatite dike in the A pit, and 4) partial replacement by fluorite of a large sill-like carbonatite body in the B pit. Electron microprobe analyses of minerals in unreplaced portions of the carbonatites show that their mineralogy consists of titaniferous magnetite, diopside pyroxene, apatite, biotite, and calcite. Magnetite contains 6.97% to 10.46% Ti02, averages 8.44% Ti02, and has an average V203 content of 0.35%. At high magnifications under the SEM, the magnetite shows abundant fine ulvöspinel exsolution lamellae arranged in a cloth texture. Apatite contains moderately high fluorine contents that range 3.21 to 5.0% and average 4.2%, and apatite crystals range in total rare earth oxides from 1.7% to 2.61%. Pyroxenes in the carbonatites are iron-rich diopside, and they contrast to pyroxenes in the fenites that are aegirine-augite. All of the microprobe analyses for mica crystals in the carbonatites give biotite compositions. The fluorite ores also have replaced marble locally in the A pit, especially along the A band in the B pit, and dominantly in the orebody proposed for the new C pit. Carbonatite and marble were preferentially replaced by fluorite because the calcite was readily soluble in the presence of the fluorite-depositing fluids and the dissolution of calcite provided calcium for the formation of fluorite.

Jan 1, 2005

By Jack S. McPartland, Gene E. McClelland

It is advisable, for any heap leach project, to develop an historical metallurgical data base to predict production heap performance before ore is mined and placed onto the heap. A data base would include results from: interval assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples; and those results plus column leach test data on diamond drill core or bulk ore composites. Subsequent larger scale heap leach test data can then be compared to the historical data base, to blast hole composite data during mining, and eventually to production data. This paper does not discuss metallurgical comparisons between assays, cyanide solubility tests, and bottle roll tests on exploration drill cuttings samples, but does discuss metallurgical comparisons from bottle roll tests, laboratory scale column leach tests, and pilot scale heap leach tests on core and bulk ore samples with operating data for three U.S. commercially producing heap leach operations. Provided that representative core or bulk samples are used for evaluation, heap leach test results accurately predict or understate the success of the commercial operation and remove most of the uncertainty from the investment decision.

Jan 1, 1990

By A. L. Ling, A. K. Janzen

"Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software and water quality calculations provided by PHREEQC, and is well-suited to modeling parameters of interest in the mining industry, especially metals and sulfate. Physical processes such as membrane separation and greensand filtration are modeled by defining mass rejections for each parameter and flow routing based on vendor projections and bench- or pilot-scale equipment testing. GoldPHREEQC models chemical precipitation processes such as HDS metals removal and gypsum precipitation by (1) performing surface-aging and solubility calculations in PHREEQC and (2) using the GoldSim framework to direct supernatant and precipitate to subsequent process steps. Users can apply this modeling framework to predict effluent water quality, chemical requirements, sludge production, and required equipment capacity to support design, troubleshooting, and cost estimating. INTRODUCTION Design of effective mine water treatment plants depends on the ability to reliably predict treatment outcomes, but systems with multiple chemical and physical treatment processes and recycle loops can be difficult to model. GoldPHREEQC is a modeling framework that integrates mass and flow routing capabilities of GoldSim software (1) and water quality calculations provided by PHREEQC (2), and is well-suited to modeling treatment of parameters of interest in the mining industry, especially metals and sulfate. GoldPHREEQC can also be applied to other water treatment scenarios using inorganic reactions and processes. The GoldPHREEQC model framework moves water and mass between specified model nodes and calculates specified reaction and water quality outcomes. It can be organized to provide flow, load, and concentration information for each location, including effluent and byproduct streams, and outputs can be adapted to include power and chemical costs."

Jan 1, 2018